diff options
author | 2018-10-20 14:55:18 +0700 | |
---|---|---|
committer | 2018-12-19 15:23:55 +0700 | |
commit | 0814c5cebd418b10a24b11e22ae08a84324d0f27 (patch) | |
tree | ebbd74ba4f5601ce202f057abf19d0d99d4a48db /meta-rcar-gen3/recipes-bsp/arm-trusted-firmware/arm-trusted-firmware_git.bb | |
parent | 98f4f5ec2c9bc4ab03d430e9cdcb4b7591a64dcd (diff) |
rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.9.2
This commit upgrades Linux BSP to v3.9.2 for the following changes:
[Kernel]
- Add support for RCKSEL clock selection.
- Fix pin functions of R-Car E3 according to H/W UM Rev1.00 errata.
- Fix warning of the make W=1 C=2.
- Identify R-Car M3 Ver.1.3.
- Add the big.LITTLE CAS scheduler fix patches.
- Fix MOD_SEL bit numbering for R-Car E3.
[Power Management]
- Fixup power-domains of 3DGE for R-Car E3 Ver.1.0 and add device
tree file for R-Car E3 Ver.1.0.
[Audio Driver]
- Fixup clock start checker.
- Resolve the problem that the noise is generated during long playback
with R-Car E3 Ebisu-4D board by kernel rebasing.
[Display Driver]
- Add function of suspend and resume to adv7511_drv.c and add hot plug
event function at resume in rcar_du_drv.c.
- Add depends on DRM_RCAR_DU to config DRM_RCAR_LVDS.
- Revert "drm: rcar-du: Fix legacy DT to create LVDS encoder nodes".
- Add clock function for LVDS PLL.
[Ethernet Driver]
- Decrease TxFIFO depth of Q3 and Q2 to one.
- Fix not to call phy_resume() if PHY is not attached and add toggling
phy reset if PHY is not attached.
- Revert "ravb: RX checksum offload" for communicating of Q-Tag VLAN
frame correctly.
- Resolved the problem that the S2RAM resume failed on R-Car E3
Ebisu-4D by kernel rebasing.
- Avoid unsupported internal delay mode for R-Car E3 and limit to
100Mbps.
[I2C Driver]
- Check bus state before reinitializing.
[IPMMU Driver]
- Fix crash on early domain free.
- Revert "arm64: defconfig: Enable QCOM_IOMMU" for suspending with
LTSI kernel.
- Correct whitelist devices assignment.
[PCIe Driver]
- Avoid PCI device removing/rescanning through sysfs triggers
a deadlock.
[PWM Driver]
- Avoid deadlock warning when removing PWM device.
[SD/MMC Driver]
- Fix card initialization failure in high speed mode.
- Add adjust HS400 offset by manual calibration mode and adjust HS400
offset by manual calibration mode for R-Car M3 Ver.1.3.
[USB2.0 Function]
- Add reset_control.
- Backport upstream patches to support OTG mode for R-Car E3.
- Make DMAC system sleep callbacks explicit.
- Add Super-Speed (b-device) support.
[Video Capture driver]
- Review adv748x driver for R-Car E3 Ebisu board and add option for
changing SD output route to TXA.
- Revert "rcar-vin: rcar-csi2: Add blank margin when caluculating bit
rate" and fix pixel rate values.
- Add CPG reset and release when using digital pin.
[RWDT Driver]
- Don't keep timer value during suspend/resume.
- Don't set divider while watchdog is running.
This also updates ADSP driver patches to adapt to the new
Linux version.
Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com>
Signed-off-by: Khang Nguyen <khang.nguyen.xv@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
Diffstat (limited to 'meta-rcar-gen3/recipes-bsp/arm-trusted-firmware/arm-trusted-firmware_git.bb')
0 files changed, 0 insertions, 0 deletions