From 9c717d4c64142e4599585256245b75cc122cacd4 Mon Sep 17 00:00:00 2001 From: Vladimir Barinov Date: Fri, 2 Feb 2018 18:16:59 +0300 Subject: LVDS: move from poc-supply to poc-gpios Use gpiod instead of gpio regulator in LVDS drivers This is ruquired to remove patch: 0035-regulator-fixed-probe-after-i2c.patch The above patch breaks regulators support on Kingfisher board --- .../linux-renesas/0030-Gen3-LVDS-cameras.patch | 65 +-- .../0040-arm64-dts-renesas-add-ADAS-boards.patch | 592 +++++---------------- 2 files changed, 163 insertions(+), 494 deletions(-) (limited to 'meta-rcar-gen3-adas/recipes-kernel') diff --git a/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0030-Gen3-LVDS-cameras.patch b/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0030-Gen3-LVDS-cameras.patch index 3c80601..2c3b903 100644 --- a/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0030-Gen3-LVDS-cameras.patch +++ b/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0030-Gen3-LVDS-cameras.patch @@ -18,7 +18,7 @@ Signed-off-by: Vladimir Barinov drivers/media/i2c/soc_camera/ar0132.h | 213 ++++ drivers/media/i2c/soc_camera/ar0220.c | 528 ++++++++++ drivers/media/i2c/soc_camera/ar0220.h | 309 ++++++ - drivers/media/i2c/soc_camera/max9286.c | 697 +++++++++++++ + drivers/media/i2c/soc_camera/max9286.c | 692 +++++++++++++ drivers/media/i2c/soc_camera/max9286.h | 244 +++++ drivers/media/i2c/soc_camera/ov10635.c | 759 ++++++++++++++ drivers/media/i2c/soc_camera/ov10635.h | 1139 ++++++++++++++++++++++ @@ -28,7 +28,7 @@ Signed-off-by: Vladimir Barinov drivers/media/i2c/soc_camera/ov490_ov10640.h | 102 ++ drivers/media/i2c/soc_camera/ov495_ov2775.c | 639 ++++++++++++ drivers/media/i2c/soc_camera/ov495_ov2775.h | 23 + - drivers/media/i2c/soc_camera/ti9x4.c | 520 ++++++++++ + drivers/media/i2c/soc_camera/ti9x4.c | 518 ++++++++++ drivers/media/i2c/soc_camera/ti9x4.h | 156 +++ drivers/media/platform/soc_camera/rcar_csi2.c | 297 ++++-- drivers/media/platform/soc_camera/rcar_vin.c | 194 +++- @@ -36,7 +36,7 @@ Signed-off-by: Vladimir Barinov drivers/media/platform/soc_camera/soc_mediabus.c | 16 + include/media/drv-intf/soc_mediabus.h | 3 + include/media/soc_camera.h | 1 + - 26 files changed, 8291 insertions(+), 109 deletions(-) + 26 files changed, 8284 insertions(+), 109 deletions(-) create mode 100644 drivers/media/i2c/soc_camera/ap0101_ar014x.c create mode 100644 drivers/media/i2c/soc_camera/ap0101_ar014x.h create mode 100644 drivers/media/i2c/soc_camera/ar0132.c @@ -2130,10 +2130,10 @@ index 0000000..29987a6 +}; diff --git a/drivers/media/i2c/soc_camera/max9286.c b/drivers/media/i2c/soc_camera/max9286.c new file mode 100644 -index 0000000..4dd80f5 +index 0000000..c850196 --- /dev/null +++ b/drivers/media/i2c/soc_camera/max9286.c -@@ -0,0 +1,697 @@ +@@ -0,0 +1,692 @@ +/* + * MAXIM max9286 GMSL driver + * @@ -2150,7 +2150,6 @@ index 0000000..4dd80f5 +#include +#include +#include -+#include +#include + +#include @@ -2193,7 +2192,7 @@ index 0000000..4dd80f5 + struct i2c_client *client; + int max9271_addr_map[4]; + int ser_id; -+ struct regulator *poc_supply[4]; /* PoC power supply */ ++ struct gpio_desc *poc_gpio[4]; /* PoC power supply */ +}; + +static char fsync_mode_default[20] = "manual"; /* manual, automatic, semi-automatic, external */ @@ -2355,12 +2354,10 @@ index 0000000..4dd80f5 + } + + if (timeout == priv->timeout / 2 && poc_trig) { -+ if (!IS_ERR(priv->poc_supply[idx])) { -+ if (regulator_disable(priv->poc_supply[idx])) -+ dev_err(&client->dev, "fail to disable POC%d regulator\n", idx); ++ if (!IS_ERR(priv->poc_gpio[idx])) { ++ gpiod_direction_output(priv->poc_gpio[idx], 0); /* POC power off */ + mdelay(200); -+ if (regulator_enable(priv->poc_supply[idx])) -+ dev_err(&client->dev, "fail to enable POC%d regulator\n", idx); ++ gpiod_direction_output(priv->poc_gpio[idx], 1); /* POC power on */ + mdelay(priv->poc_delay); + } + } @@ -2499,9 +2496,8 @@ index 0000000..4dd80f5 + max9286_initial_setup(client); + + for (idx = 0; idx < priv->links; idx++) { -+ if (!IS_ERR(priv->poc_supply[idx])) { -+ if (regulator_enable(priv->poc_supply[idx])) -+ dev_err(&client->dev, "fail to enable POC%d regulator\n", idx); ++ if (!IS_ERR(priv->poc_gpio[idx])) { ++ gpiod_direction_output(priv->poc_gpio[idx], 1); /* POC power on */ + mdelay(priv->poc_delay); + } + @@ -2609,8 +2605,8 @@ index 0000000..4dd80f5 + struct property *prop; + int err, pwen, i; + int sensor_delay, gpio0 = 1, gpio1 = 1; -+ + u8 val = 0; ++ char poc_name[10]; + + if (of_property_read_u32(np, "maxim,links", &priv->links)) + priv->links = 4; @@ -2627,6 +2623,11 @@ index 0000000..4dd80f5 + + mdelay(250); + ++ for (i = 0; i < 4; i++) { ++ sprintf(poc_name, "POC%d", i); ++ priv->poc_gpio[i] = devm_gpiod_get_optional(&client->dev, poc_name, 0); ++ } ++ + reg8_read(client, 0x1e, &val); /* read max9286 ID */ + if (val != MAX9286_ID) { + prop = of_find_property(np, "reg", NULL); @@ -2744,7 +2745,6 @@ index 0000000..4dd80f5 +{ + struct max9286_priv *priv; + int err, i; -+ char supply_name[10]; + + priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) @@ -2760,11 +2760,6 @@ index 0000000..4dd80f5 + if (err) + goto out; + -+ for (i = 0; i < 4; i++) { -+ sprintf(supply_name, "POC%d", i); -+ priv->poc_supply[i] = devm_regulator_get_optional(&client->dev, supply_name); -+ } -+ + err = max9286_initialize(client); + if (err < 0) + goto out; @@ -7108,11 +7103,11 @@ index 0000000..3f53689 +}; diff --git a/drivers/media/i2c/soc_camera/ti9x4.c b/drivers/media/i2c/soc_camera/ti9x4.c new file mode 100644 -index 0000000..aac892b +index 0000000..a4c7b3f --- /dev/null +++ b/drivers/media/i2c/soc_camera/ti9x4.c -@@ -0,0 +1,520 @@ -+/* +@@ -0,0 +1,518 @@ ++ /* + * TI DS90UB954/960/964 FPDLinkIII driver + * + * Copyright (C) 2017-2018 Cogent Embedded, Inc. @@ -7128,7 +7123,6 @@ index 0000000..aac892b +#include +#include +#include -+#include +#include + +#include @@ -7156,7 +7150,7 @@ index 0000000..aac892b + int ti9x3_addr_map[4]; + char chip_id[6]; + int ser_id; -+ struct regulator *poc_supply[4]; /* PoC power supply */ ++ struct gpio_desc *poc_gpio[4]; /* PoC power supply */ +}; + +static int ser_id; @@ -7350,9 +7344,8 @@ index 0000000..aac892b + ti9x4_initial_setup(client); + + for (idx = 0; idx < priv->links; idx++) { -+ if (!IS_ERR(priv->poc_supply[idx])) { -+ if (regulator_enable(priv->poc_supply[idx])) -+ dev_err(&client->dev, "fail to enable POC%d regulator\n", idx); ++ if (!IS_ERR(priv->poc_gpio[idx])) { ++ gpiod_direction_output(priv->poc_gpio[idx], 1); /* POC power on */ + mdelay(priv->poc_delay); + } + @@ -7443,6 +7436,7 @@ index 0000000..aac892b + char forwarding_mode_default[20] = "round-robin"; /* round-robin, synchronized */ + struct property *csi_rate_prop, *dvp_order_prop; + u8 val = 0; ++ char poc_name[10]; + + if (of_property_read_u32(np, "ti,links", &priv->links)) + priv->links = 4; @@ -7459,6 +7453,11 @@ index 0000000..aac892b + mdelay(250); + } + ++ for (i = 0; i < 4; i++) { ++ sprintf(poc_name, "POC%d", i); ++ priv->poc_gpio[i] = devm_gpiod_get_optional(&client->dev, poc_name, 0); ++ } ++ + reg8_read(client, 0x00, &val); /* read TI9x4 I2C address */ + if (val != (priv->des_addr << 1)) { + prop = of_find_property(np, "reg", NULL); @@ -7547,7 +7546,6 @@ index 0000000..aac892b +{ + struct ti9x4_priv *priv; + int err, i; -+ char supply_name[10]; + + priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) @@ -7562,11 +7560,6 @@ index 0000000..aac892b + if (err) + goto out; + -+ for (i = 0; i < 4; i++) { -+ sprintf(supply_name, "POC%d", i); -+ priv->poc_supply[i] = devm_regulator_get_optional(&client->dev, supply_name); -+ } -+ + err = ti9x4_initialize(client); + if (err < 0) + goto out; diff --git a/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0040-arm64-dts-renesas-add-ADAS-boards.patch b/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0040-arm64-dts-renesas-add-ADAS-boards.patch index b351089..b33ccc9 100644 --- a/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0040-arm64-dts-renesas-add-ADAS-boards.patch +++ b/meta-rcar-gen3-adas/recipes-kernel/linux/linux-renesas/0040-arm64-dts-renesas-add-ADAS-boards.patch @@ -33,11 +33,11 @@ Signed-off-by: Vladimir Barinov --- arch/arm64/boot/dts/renesas/Makefile | 22 + arch/arm64/boot/dts/renesas/legacy/Makefile | 8 + - .../renesas/legacy/r8a7795-es1-h3ulcb-kf-v0.dts | 1624 ++++++++++++++++++ - .../renesas/legacy/r8a7795-es1-h3ulcb-kf-v1.dts | 441 +++++ + .../renesas/legacy/r8a7795-es1-h3ulcb-kf-v0.dts | 1624 +++++++++++++++++++ + .../renesas/legacy/r8a7795-es1-h3ulcb-kf-v1.dts | 441 ++++++ .../dts/renesas/legacy/r8a7795-h3ulcb-kf-v0.dts | 1638 +++++++++++++++++++ .../dts/renesas/legacy/r8a7795-h3ulcb-kf-v1.dts | 465 ++++++ - .../dts/renesas/legacy/r8a7796-m3ulcb-kf-v0.dts | 1171 +++++++++++++ + .../dts/renesas/legacy/r8a7796-m3ulcb-kf-v0.dts | 1171 ++++++++++++++ .../dts/renesas/legacy/r8a7796-m3ulcb-kf-v1.dts | 465 ++++++ .../dts/renesas/legacy/r8a7797-v3msk-kf-v0.dts | 82 + .../boot/dts/renesas/legacy/ulcb-kf-cmos.dtsi | 75 + @@ -49,7 +49,7 @@ Signed-off-by: Vladimir Barinov .../boot/dts/renesas/r8a7795-es1-h3ulcb-vb.dts | 69 + .../boot/dts/renesas/r8a7795-es1-h3ulcb-vb2.dts | 77 + .../boot/dts/renesas/r8a7795-es1-h3ulcb-vbm.dts | 26 + - .../boot/dts/renesas/r8a7795-es1-h3ulcb-view.dts | 544 ++++++ + .../boot/dts/renesas/r8a7795-es1-h3ulcb-view.dts | 544 +++++++ .../dts/renesas/r8a7795-es1-salvator-x-view.dts | 550 +++++++ .../boot/dts/renesas/r8a7795-h3ulcb-had-alfa.dts | 22 + .../boot/dts/renesas/r8a7795-h3ulcb-had-beta.dts | 23 + @@ -58,28 +58,28 @@ Signed-off-by: Vladimir Barinov arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-vb.dts | 68 + arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-vb2.dts | 68 + arch/arm64/boot/dts/renesas/r8a7795-h3ulcb-vbm.dts | 26 + - .../arm64/boot/dts/renesas/r8a7795-h3ulcb-view.dts | 544 ++++++ + .../arm64/boot/dts/renesas/r8a7795-h3ulcb-view.dts | 544 +++++++ .../boot/dts/renesas/r8a7795-salvator-x-view.dts | 550 +++++++ arch/arm64/boot/dts/renesas/r8a7796-m3ulcb-kf.dts | 40 + .../arm64/boot/dts/renesas/r8a7796-m3ulcb-view.dts | 286 ++++ .../boot/dts/renesas/r8a7796-salvator-x-view.dts | 317 ++++ .../boot/dts/renesas/r8a7797-eagle-function.dts | 62 + arch/arm64/boot/dts/renesas/r8a7797-eagle.dts | 575 +++++++ - arch/arm64/boot/dts/renesas/r8a7797-v3msk-kf.dts | 533 ++++++ - arch/arm64/boot/dts/renesas/r8a7797-v3msk-vbm.dts | 548 +++++++ + arch/arm64/boot/dts/renesas/r8a7797-v3msk-kf.dts | 520 ++++++ + arch/arm64/boot/dts/renesas/r8a7797-v3msk-vbm.dts | 513 ++++++ arch/arm64/boot/dts/renesas/r8a7797-v3msk-view.dts | 297 ++++ arch/arm64/boot/dts/renesas/r8a7797-v3msk.dts | 314 ++++ arch/arm64/boot/dts/renesas/r8a7797-v3mzf.dts | 424 +++++ - arch/arm64/boot/dts/renesas/r8a7798-condor.dts | 963 +++++++++++ - arch/arm64/boot/dts/renesas/ulcb-kf-cn11.dtsi | 498 ++++++ + arch/arm64/boot/dts/renesas/r8a7798-condor.dts | 963 ++++++++++++ + arch/arm64/boot/dts/renesas/ulcb-kf-cn11.dtsi | 462 ++++++ arch/arm64/boot/dts/renesas/ulcb-kf-most.dtsi | 30 + arch/arm64/boot/dts/renesas/ulcb-kf-sd3.dtsi | 46 + - arch/arm64/boot/dts/renesas/ulcb-kf.dtsi | 1492 +++++++++++++++++ - arch/arm64/boot/dts/renesas/ulcb-vb-cn12.dtsi | 495 ++++++ - arch/arm64/boot/dts/renesas/ulcb-vb.dtsi | 1678 +++++++++++++++++++ - arch/arm64/boot/dts/renesas/ulcb-vb2.dtsi | 1724 ++++++++++++++++++++ - arch/arm64/boot/dts/renesas/ulcb-vbm.dtsi | 577 +++++++ - 48 files changed, 20093 insertions(+) + arch/arm64/boot/dts/renesas/ulcb-kf.dtsi | 1458 +++++++++++++++++ + arch/arm64/boot/dts/renesas/ulcb-vb-cn12.dtsi | 459 ++++++ + arch/arm64/boot/dts/renesas/ulcb-vb.dtsi | 1610 +++++++++++++++++++ + arch/arm64/boot/dts/renesas/ulcb-vb2.dtsi | 1656 ++++++++++++++++++++ + arch/arm64/boot/dts/renesas/ulcb-vbm.dtsi | 543 +++++++ + 48 files changed, 19769 insertions(+) create mode 100644 arch/arm64/boot/dts/renesas/legacy/Makefile create mode 100644 arch/arm64/boot/dts/renesas/legacy/r8a7795-es1-h3ulcb-kf-v0.dts create mode 100644 arch/arm64/boot/dts/renesas/legacy/r8a7795-es1-h3ulcb-kf-v1.dts @@ -10812,10 +10812,10 @@ index 0000000..ce7a88e +}; diff --git a/arch/arm64/boot/dts/renesas/r8a7797-v3msk-kf.dts b/arch/arm64/boot/dts/renesas/r8a7797-v3msk-kf.dts new file mode 100644 -index 0000000..c61b613 +index 0000000..862236f --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a7797-v3msk-kf.dts -@@ -0,0 +1,533 @@ +@@ -0,0 +1,520 @@ +/* + * Device Tree Source for the V3MSK Kingfisher board on r8a7797 + * @@ -10999,6 +10999,11 @@ index 0000000..c61b613 + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "coax"; + ++ POC0-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; ++ + port@0 { + ti9x4_des0ep0: endpoint@0 { + ti9x3-addr = <0x0c>; @@ -11039,6 +11044,11 @@ index 0000000..c61b613 + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; + ++ POC0-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; ++ + port@0 { + max9286_des0ep0: endpoint@0 { + max9271-addr = <0x50>; @@ -11076,9 +11086,10 @@ index 0000000..c61b613 + reg = <6>; + /* Slot B (CN11) */ + -+ video_a_ext0: pca9535@27 { ++ /* PCA9535 is a redundant/deprecated card */ ++ gpio_exp_a_26: gpio@26 { + compatible = "nxp,pca9535"; -+ reg = <0x27>; ++ reg = <0x26>; + gpio-controller; + #gpio-cells = <2>; + @@ -11138,7 +11149,7 @@ index 0000000..c61b613 + }; + }; + -+ video_a_ext1: max7325@5c { ++ gpio_exp_a_5c: gpio@5c { + compatible = "maxim,max7325"; + reg = <0x5c>; + gpio-controller; @@ -11168,30 +11179,6 @@ index 0000000..c61b613 + output-high; + line-name = "Video-A PWR_SHDN"; + }; -+ video_a_cam_pwr0 { -+ gpio-hog; -+ gpios = <8 GPIO_ACTIVE_HIGH>; -+ output-high; -+ line-name = "Video-A PWR0"; -+ }; -+ video_a_cam_pwr1 { -+ gpio-hog; -+ gpios = <9 GPIO_ACTIVE_HIGH>; -+ output-high; -+ line-name = "Video-A PWR1"; -+ }; -+ video_a_cam_pwr2 { -+ gpio-hog; -+ gpios = <10 GPIO_ACTIVE_HIGH>; -+ output-high; -+ line-name = "Video-A PWR2"; -+ }; -+ video_a_cam_pwr3 { -+ gpio-hog; -+ gpios = <11 GPIO_ACTIVE_HIGH>; -+ output-high; -+ line-name = "Video-A PWR3"; -+ }; + video_a_des_shdn { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; @@ -11351,10 +11338,10 @@ index 0000000..c61b613 +}; diff --git a/arch/arm64/boot/dts/renesas/r8a7797-v3msk-vbm.dts b/arch/arm64/boot/dts/renesas/r8a7797-v3msk-vbm.dts new file mode 100644 -index 0000000..d355adb +index 0000000..226b659 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a7797-v3msk-vbm.dts -@@ -0,0 +1,548 @@ +@@ -0,0 +1,513 @@ +/* + * Device Tree Source for the V3MSK Videobox Mini board on r8a7797 + * @@ -11373,42 +11360,6 @@ index 0000000..d355adb + aliases { + serial1 = &scif3; + }; -+ -+ pwr0: regulator-pwr0 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1: regulator-pwr1 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2: regulator-pwr2 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3: regulator-pwr3 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; +}; + +&canfd { @@ -11570,10 +11521,11 @@ index 0000000..d355adb + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr0>; -+ POC1-supply = <&pwr1>; -+ POC2-supply = <&pwr2>; -+ POC3-supply = <&pwr3>; ++ ++ POC0-gpios = <&gpio_exp_6c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_6c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_6c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_6c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des0ep0: endpoint@0 { @@ -11612,10 +11564,10 @@ index 0000000..d355adb + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "coax"; -+ POC0-supply = <&pwr0>; -+ POC1-supply = <&pwr1>; -+ POC2-supply = <&pwr2>; -+ POC3-supply = <&pwr3>; ++ POC0-gpio = <&gpio_exp_6c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpio = <&gpio_exp_6c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpio = <&gpio_exp_6c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpio = <&gpio_exp_6c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des0ep0: endpoint@0 { @@ -13927,10 +13879,10 @@ index 0000000..cdd9844 +}; diff --git a/arch/arm64/boot/dts/renesas/ulcb-kf-cn11.dtsi b/arch/arm64/boot/dts/renesas/ulcb-kf-cn11.dtsi new file mode 100644 -index 0000000..095a503 +index 0000000..a87c38b --- /dev/null +++ b/arch/arm64/boot/dts/renesas/ulcb-kf-cn11.dtsi -@@ -0,0 +1,498 @@ +@@ -0,0 +1,462 @@ +/* + * Device Tree Source for the H3ULCB Kingfisher board: + * this adding conflicting resource on VIN4/VIN5/VIN6/VIN7 for CN11 @@ -13944,44 +13896,6 @@ index 0000000..095a503 + * kind, whether express or implied. + */ + -+/ { -+ pwr0B: regulator-pwr0B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1B: regulator-pwr1B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2B: regulator-pwr2B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3B: regulator-pwr3B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+}; -+ +&i2cswitch4 { + i2c@2 { + #address-cells = <1>; @@ -14080,10 +13994,11 @@ index 0000000..095a503 + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "coax"; -+ POC0-supply = <&pwr0B>; -+ POC1-supply = <&pwr1B>; -+ POC2-supply = <&pwr2B>; -+ POC3-supply = <&pwr3B>; ++ ++ POC0-gpios = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des1ep0: endpoint@0 { @@ -14125,10 +14040,11 @@ index 0000000..095a503 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr1B>; -+ POC1-supply = <&pwr0B>; -+ POC2-supply = <&pwr3B>; -+ POC3-supply = <&pwr2B>; ++ ++ POC0-gpios = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des1ep0: endpoint@0 { @@ -14519,10 +14435,10 @@ index 0000000..b854216 +}; diff --git a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi new file mode 100644 -index 0000000..a33a2a0 +index 0000000..447cfc3 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi -@@ -0,0 +1,1492 @@ +@@ -0,0 +1,1458 @@ +/* + * Device Tree Source for the ULCB Kingfisher board + * @@ -14642,42 +14558,6 @@ index 0000000..a33a2a0 + enable-active-high; + }; + -+ pwr0A: regulator-pwr0A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1A: regulator-pwr1A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2A: regulator-pwr2A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3A: regulator-pwr3A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ + kim { + compatible = "kim"; + shutdown-gpios = <&gpio_ext_74 3 GPIO_ACTIVE_HIGH>; @@ -15415,10 +15295,11 @@ index 0000000..a33a2a0 + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "coax"; -+ POC0-supply = <&pwr0A>; -+ POC1-supply = <&pwr1A>; -+ POC2-supply = <&pwr2A>; -+ POC3-supply = <&pwr3A>; ++ ++ POC0-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des0ep0: endpoint@0 { @@ -15459,10 +15340,11 @@ index 0000000..a33a2a0 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr1A>; -+ POC1-supply = <&pwr0A>; -+ POC2-supply = <&pwr3A>; -+ POC3-supply = <&pwr2A>; ++ ++ POC0-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des0ep0: endpoint@0 { @@ -16017,10 +15899,10 @@ index 0000000..a33a2a0 + diff --git a/arch/arm64/boot/dts/renesas/ulcb-vb-cn12.dtsi b/arch/arm64/boot/dts/renesas/ulcb-vb-cn12.dtsi new file mode 100644 -index 0000000..778a477 +index 0000000..b29fc18 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/ulcb-vb-cn12.dtsi -@@ -0,0 +1,495 @@ +@@ -0,0 +1,459 @@ +/* + * Device Tree Source for the H3ULCB Videobox board: + * this adding conflicting resource on VIN4/VIN5/VIN6/VIN7 for CN12 @@ -16033,44 +15915,6 @@ index 0000000..778a477 + * kind, whether express or implied. + */ + -+/ { -+ pwr0C: regulator-pwr0C { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0C"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_c_5c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1C: regulator-pwr1C { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1C"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_c_5c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2C: regulator-pwr2C { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2C"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_c_5c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3C: regulator-pwr3C { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3C"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_c_5c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+}; -+ +&i2cswitch2 { + i2c@3 { + #address-cells = <1>; @@ -16171,10 +16015,11 @@ index 0000000..778a477 + ti,lanes = <2>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "coax"; -+ POC0-supply = <&pwr0C>; -+ POC1-supply = <&pwr1C>; -+ POC2-supply = <&pwr2C>; -+ POC3-supply = <&pwr3C>; ++ ++ POC0-gpios = <&gpio_exp_c_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_c_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_c_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_c_5c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des2ep0: endpoint@0 { @@ -16216,10 +16061,11 @@ index 0000000..778a477 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr1C>; -+ POC1-supply = <&pwr0C>; -+ POC2-supply = <&pwr3C>; -+ POC3-supply = <&pwr2C>; ++ ++ POC0-gpios = <&gpio_exp_c_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_c_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_c_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_c_5c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des2ep0: endpoint@0 { @@ -16518,10 +16364,10 @@ index 0000000..778a477 +}; diff --git a/arch/arm64/boot/dts/renesas/ulcb-vb.dtsi b/arch/arm64/boot/dts/renesas/ulcb-vb.dtsi new file mode 100644 -index 0000000..07594447 +index 0000000..0185e46 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/ulcb-vb.dtsi -@@ -0,0 +1,1678 @@ +@@ -0,0 +1,1610 @@ +/* + * Device Tree Source for the ULCB Videobox board + * @@ -16624,78 +16470,6 @@ index 0000000..07594447 + regulator-always-on; + }; + -+ pwr0A: regulator-pwr0A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1A: regulator-pwr1A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2A: regulator-pwr2A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3A: regulator-pwr3A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr0B: regulator-pwr0B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1B: regulator-pwr1B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2B: regulator-pwr2B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3B: regulator-pwr3B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ + /delete-node/sound; + + rsnd_ak4613: sound@0 { @@ -17127,10 +16901,11 @@ index 0000000..07594447 + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "stp"; -+ POC0-supply = <&pwr0A>; -+ POC1-supply = <&pwr1A>; -+ POC2-supply = <&pwr2A>; -+ POC3-supply = <&pwr3A>; ++ ++ POC0-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des0ep0: endpoint@0 { @@ -17171,10 +16946,11 @@ index 0000000..07594447 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr1A>; -+ POC1-supply = <&pwr0A>; -+ POC2-supply = <&pwr3A>; -+ POC3-supply = <&pwr2A>; ++ ++ POC0-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des0ep0: endpoint@0 { @@ -17305,10 +17081,11 @@ index 0000000..07594447 + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "stp"; -+ POC0-supply = <&pwr0B>; -+ POC1-supply = <&pwr1B>; -+ POC2-supply = <&pwr2B>; -+ POC3-supply = <&pwr3B>; ++ ++ POC0-gpios = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des1ep0: endpoint@0 { @@ -17349,10 +17126,11 @@ index 0000000..07594447 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr1B>; -+ POC1-supply = <&pwr0B>; -+ POC2-supply = <&pwr3B>; -+ POC3-supply = <&pwr2B>; ++ ++ POC0-gpios = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des1ep0: endpoint@0 { @@ -18202,10 +17980,10 @@ index 0000000..07594447 +//#include "ulcb-vb-cn12.dtsi" diff --git a/arch/arm64/boot/dts/renesas/ulcb-vb2.dtsi b/arch/arm64/boot/dts/renesas/ulcb-vb2.dtsi new file mode 100644 -index 0000000..b0145a2 +index 0000000..92a3300 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/ulcb-vb2.dtsi -@@ -0,0 +1,1724 @@ +@@ -0,0 +1,1656 @@ +/* + * Device Tree Source for the ULCB Videobox V2 board + * @@ -18302,78 +18080,6 @@ index 0000000..b0145a2 + regulator-always-on; + }; + -+ pwr0A: regulator-pwr0A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1A: regulator-pwr1A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2A: regulator-pwr2A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3A: regulator-pwr3A { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3A"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr0B: regulator-pwr0B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1B: regulator-pwr1B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2B: regulator-pwr2B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3B: regulator-pwr3B { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3B"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ + /delete-node/sound; + + rsnd_ak4613: sound@0 { @@ -18829,10 +18535,11 @@ index 0000000..b0145a2 + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "stp"; -+ POC0-supply = <&pwr0A>; -+ POC1-supply = <&pwr1A>; -+ POC2-supply = <&pwr2A>; -+ POC3-supply = <&pwr3A>; ++ ++ POC0-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des0ep0: endpoint@0 { @@ -18873,10 +18580,11 @@ index 0000000..b0145a2 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr1A>; -+ POC1-supply = <&pwr0A>; -+ POC2-supply = <&pwr3A>; -+ POC3-supply = <&pwr2A>; ++ ++ POC0-gpios = <&gpio_exp_a_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_a_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_a_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_a_5c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des0ep0: endpoint@0 { @@ -19007,10 +18715,11 @@ index 0000000..b0145a2 + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "stp"; -+ POC0-supply = <&pwr0B>; -+ POC1-supply = <&pwr1B>; -+ POC2-supply = <&pwr2B>; -+ POC3-supply = <&pwr3B>; ++ ++ POC0-gpios = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des1ep0: endpoint@0 { @@ -19051,10 +18760,11 @@ index 0000000..b0145a2 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr1B>; -+ POC1-supply = <&pwr0B>; -+ POC2-supply = <&pwr3B>; -+ POC3-supply = <&pwr2B>; ++ ++ POC0-gpios = <&gpio_exp_b_5c 9 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_b_5c 8 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_b_5c 11 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_b_5c 10 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des1ep0: endpoint@0 { @@ -19936,10 +19646,10 @@ index 0000000..b0145a2 +//#include "ulcb-vb2-cn12.dtsi" diff --git a/arch/arm64/boot/dts/renesas/ulcb-vbm.dtsi b/arch/arm64/boot/dts/renesas/ulcb-vbm.dtsi new file mode 100644 -index 0000000..bc36e95 +index 0000000..47e2b2d --- /dev/null +++ b/arch/arm64/boot/dts/renesas/ulcb-vbm.dtsi -@@ -0,0 +1,577 @@ +@@ -0,0 +1,543 @@ +/* + * Device Tree Source for the ULCB Videobox Mini board + * @@ -19955,42 +19665,6 @@ index 0000000..bc36e95 + serial1 = &scif1; + }; + -+ pwr0: regulator-pwr0 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR0"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 8 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr1: regulator-pwr1 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR1"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 9 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr2: regulator-pwr2 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR2"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 10 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ -+ pwr3: regulator-pwr3 { -+ compatible = "regulator-fixed"; -+ regulator-name = "PWR3"; -+ regulator-min-microvolt = <9000000>; -+ regulator-max-microvolt = <9000000>; -+ gpio = <&gpio_exp_6c 11 GPIO_ACTIVE_HIGH>; -+ enable-active-high; -+ }; -+ + lvds-encoder { + compatible = "thine,thc63lvdm83d"; + @@ -20211,10 +19885,11 @@ index 0000000..bc36e95 + maxim,resetb-gpio = <1>; + maxim,fsync-mode = "automatic"; + maxim,timeout = <100>; -+ POC0-supply = <&pwr0>; -+ POC1-supply = <&pwr1>; -+ POC2-supply = <&pwr2>; -+ POC3-supply = <&pwr3>; ++ ++ POC0-gpios = <&gpio_exp_6c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_6c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_6c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_6c 1 GPIO_ACTIVE_HIGH>; + + port@0 { + max9286_des0ep0: endpoint@0 { @@ -20254,10 +19929,11 @@ index 0000000..bc36e95 + ti,lanes = <4>; + ti,forwarding-mode = "round-robin"; + ti,cable-mode = "coax"; -+ POC0-supply = <&pwr0>; -+ POC1-supply = <&pwr1>; -+ POC2-supply = <&pwr2>; -+ POC3-supply = <&pwr3>; ++ ++ POC0-gpios = <&gpio_exp_6c 8 GPIO_ACTIVE_HIGH>; ++ POC1-gpios = <&gpio_exp_6c 9 GPIO_ACTIVE_HIGH>; ++ POC2-gpios = <&gpio_exp_6c 10 GPIO_ACTIVE_HIGH>; ++ POC3-gpios = <&gpio_exp_6c 1 GPIO_ACTIVE_HIGH>; + + port@0 { + ti9x4_des0ep0: endpoint@0 { -- cgit 1.2.3-korg