From c4227b7989785af8a08ae8dba5d0a8ffcbf21b77 Mon Sep 17 00:00:00 2001 From: Ronan Date: Tue, 13 Dec 2016 10:41:21 +0100 Subject: fix markdown syntax Signed-off-by: Ronan --- getting-started/machines/R-Car-Starter-Kit-gen3.md | 33 ++++++++++++++++------ 1 file changed, 24 insertions(+), 9 deletions(-) (limited to 'getting-started') diff --git a/getting-started/machines/R-Car-Starter-Kit-gen3.md b/getting-started/machines/R-Car-Starter-Kit-gen3.md index 523a6b9..040e70b 100644 --- a/getting-started/machines/R-Car-Starter-Kit-gen3.md +++ b/getting-started/machines/R-Car-Starter-Kit-gen3.md @@ -24,7 +24,7 @@ The following documents may also be helpful: Before setting up the build environment, you need to download the proprietary drivers. * Download Renesas graphics drivers with a "click through" license from Renesas website [Link][rcar demoboard] - * Under the Target hardware: **R-Car H3/M3** section. + * Under the Target hardware: **R-Car H3/M3** section. #### Note: @@ -33,6 +33,7 @@ The operation is fast and simple but nevertheless mandatory to access evaluation Once you registered, you can download two zip files. * The files must be stored into your download directory (usually $HOME/Downloads, pointed by $XDG_DOWNLOAD_DIR). Here after is an example of the typical files downloaded at the time of writing: + ``` chmod a+r $XDG_DOWNLOAD_DIR/*.zip ls -l $XDG_DOWNLOAD_DIR @@ -86,6 +87,7 @@ Generating setup file: /home/working/workspace_agl_master/build_gen3/agl-init-bu ------------ aglsetup.sh: Done [snip] ``` + If you encounter this issue, or any other unwanted behavior, you can fix the error mentioned and then clean up by removing the “$AGL_TOP/build” directory then re-launch the procedure again. After this command, the working directory is changed to $AGL_TOP/build. @@ -99,12 +101,13 @@ or MACHINE = "m3ulcb" ``` -Configure for Release or Development: development images contain extra tools for developer convenience, in particular: +Configure for Release or Development: +* development images contain extra tools for developer convenience, in particular: * a debugger (gdb) * some tweaks, including a disabled root password * a SFTP server * the TCF Agent for easier application deployment and remote debugging - * some extra system tools (usb, bluetooth ...) + * some extra system tools (usb, bluetooth ...) * ... We explicitely activate these debug facilities by specifying the “agl-devel agl-netboot” feature. @@ -137,7 +140,7 @@ Then, for each build, the SD-card is merely rewritten and used to boot the confi ## Prepare the SD-card on the host -Plug the microSD card and get its associated device by either running *dmesg | tail -15* or *lsblk*, for example: +Plug the microSD card and get its associated device by either running *`dmesg | tail -15`* or *`lsblk`*, for example: ``` dmesg | tail -15 @@ -165,7 +168,7 @@ lsblk └─sdc2 8:34 1 788M 0 part ``` -** IMPORTANT NOTE **: This is a critical operation, each computer is different and removable devices can change from time to time: so you should repeat this operation each time you insert the microSD card to confirm the device name. +**IMPORTANT NOTE**: This is a critical operation, each computer is different and removable devices can change from time to time: so you should repeat this operation each time you insert the microSD card to confirm the device name. In the example above, we see: * the first SATA drive as 'sda'. @@ -205,6 +208,7 @@ sudo fdisk /dev/sdc Calling ioctl() to re-read partition table. Syncing disks. ``` + * Initialize the ext4 partition using “mke2fs”; for example, if the microSD card is associated with *sdc*: ``` @@ -248,7 +252,7 @@ Make sure the filesystem is empty: sudo rm -rf ${SDCARD:-bad_dir}/* ``` -** IMPORTANT NOTE **: Verify that **tar** version is 1.28 or newer: this is required to create extended attributes correctly on the SD-card, and in particular SMACK labels used to enforce security. Check with the following command: +**IMPORTANT NOTE**: Verify that **tar** version is 1.28 or newer: this is required to create extended attributes correctly on the SD-card, and in particular SMACK labels used to enforce security. Check with the following command: ``` tar --version @@ -442,6 +446,7 @@ Hit any key to stop autoboot: 0 * Hit any key to stop autoboot (warning you have only few seconds). * Check if you have correct parameters for booting your board: * For machine m3ulcb: + ``` => print baudrate=115200 @@ -461,6 +466,7 @@ Hit any key to stop autoboot: 0 ``` * For machine h3ulcb: + ``` => printenv baudrate=115200 @@ -481,23 +487,30 @@ Hit any key to stop autoboot: 0 ``` * If not, copy line by line: + ``` setenv bootargs console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait rw rootfstype=ext4 setenv bootcmd run load_ker\; run load_dtb\; booti 0x48080000 - 0x48000000 setenv load_ker ext4load mmc 0:1 0x48080000 /boot/Image ``` + * For machine h3ulcb: + ``` setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/Image-r8a7795-h3ulcb.dtb ``` + * For machine m3ulcb: + ``` setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/Image-r8a7796-m3ulcb.dtb ``` - * Finally save boot environment: - ``` + + * Finally save boot environment: + + ``` saveenv - ``` + ``` * Now you can boot: @@ -540,6 +553,7 @@ setenv bootmmc '1:1' setenv bootcmd_sd 'ext4load mmc ${bootmmc} 0x40007fc0 boot/uImage+dtb' setenv bootcmd 'setenv bootargs ${bootargs_console} ${bootargs_video} ${bootargs_root}; run bootcmd_sd; bootm 0x40007fc0' ``` + **WARNINGS:** If no display shows up when booting, e.g. for a non-full HD screen, replace **1920x1080** value in the **bootargs_video** variable with lower screen resolution such as **1024x768**. Unfortunately at the moment, there is no universally supported setting. @@ -604,6 +618,7 @@ root@m3ulcb:~# ``` Here, IP address is 10.0.0.27. Logging in using SSH is easy: + ``` $ ssh root@10.0.0.27 Last login: Tue Dec 6 10:01:11 2016 from 10.0.0.13 -- cgit 1.2.3-korg