rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.9.2

This commit upgrades Linux BSP to v3.9.2 for the following changes:

[Kernel]
- Add support for RCKSEL clock selection.
- Fix pin functions of R-Car E3 according to H/W UM Rev1.00 errata.
- Fix warning of the make W=1 C=2.
- Identify R-Car M3 Ver.1.3.
- Add the big.LITTLE CAS scheduler fix patches.
- Fix MOD_SEL bit numbering for R-Car E3.

[Power Management]
- Fixup power-domains of 3DGE for R-Car E3 Ver.1.0 and add device
tree file for R-Car E3 Ver.1.0.

[Audio Driver]
- Fixup clock start checker.
- Resolve the problem that the noise is generated during long playback
with R-Car E3 Ebisu-4D board by kernel rebasing.

[Display Driver]
- Add function of suspend and resume to adv7511_drv.c and add hot plug
event function at resume in rcar_du_drv.c.
- Add depends on DRM_RCAR_DU to config DRM_RCAR_LVDS.
- Revert "drm: rcar-du: Fix legacy DT to create LVDS encoder nodes".
- Add clock function for LVDS PLL.

[Ethernet Driver]
- Decrease TxFIFO depth of Q3 and Q2 to one.
- Fix not to call phy_resume() if PHY is not attached and add toggling
phy reset if PHY is not attached.
- Revert "ravb: RX checksum offload" for communicating of Q-Tag VLAN
frame correctly.
- Resolved the problem that the S2RAM resume failed on R-Car E3
Ebisu-4D by kernel rebasing.
- Avoid unsupported internal delay mode for R-Car E3 and limit to
100Mbps.

[I2C Driver]
- Check bus state before reinitializing.

[IPMMU Driver]
- Fix crash on early domain free.
- Revert "arm64: defconfig: Enable QCOM_IOMMU" for suspending with
LTSI kernel.
- Correct whitelist devices assignment.

[PCIe Driver]
- Avoid PCI device removing/rescanning through sysfs triggers
a deadlock.

[PWM Driver]
- Avoid deadlock warning when removing PWM device.

[SD/MMC Driver]
- Fix card initialization failure in high speed mode.
- Add adjust HS400 offset by manual calibration mode and adjust HS400
offset by manual calibration mode for R-Car M3 Ver.1.3.

[USB2.0 Function]
- Add reset_control.
- Backport upstream patches to support OTG mode for R-Car E3.
- Make DMAC system sleep callbacks explicit.
- Add Super-Speed (b-device) support.

[Video Capture driver]
- Review adv748x driver for R-Car E3 Ebisu board and add option for
changing SD output route to TXA.
- Revert "rcar-vin: rcar-csi2: Add blank margin when caluculating bit
rate" and fix pixel rate values.
- Add CPG reset and release when using digital pin.

[RWDT Driver]
- Don't keep timer value during suspend/resume.
- Don't set divider while watchdog is running.

This also updates ADSP driver patches to adapt to the new
Linux version.

Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com>
Signed-off-by: Khang Nguyen <khang.nguyen.xv@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>

1 files changed, 0 insertions, 83 deletions

diff --git a/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0001-arm64-dts-salvator-common-Rcar-Sound.patch b/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0001-arm64-dts-salvator-common-Rcar-Sound.patch
deleted file mode 100644
index a7e0587..0000000
--- a/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0001-arm64-dts-salvator-common-Rcar-Sound.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From cda5747801eadd0f29a591bee4b36c6f1ae30a54 Mon Sep 17 00:00:00 2001
-From: Takeshi Kihara <takeshi.kihara.df@renesas.com>
-Date: Fri, 19 Oct 2018 11:48:30 +0900
-Subject: [PATCH 1/6] arm64: dts: salvator-common: Rcar-Sound
-
-This Patch Adds Rcar_Sound
-
-Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
----
- .../boot/dts/renesas/salvator-common.dtsi     | 40 ++++++++-----------
- 1 file changed, 16 insertions(+), 24 deletions(-)
-
-diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
-index 3257143e43c1..6cda02800731 100644
---- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
-+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
-@@ -125,15 +125,21 @@
- 		regulator-boot-on;
- 		regulator-always-on;
- 	};
-+	rsnd_ak4613: sound {
-+		compatible = "simple-audio-card";
-+		simple-audio-card,format = "left_j";
-+		simple-audio-card,bitclock-master = <&sndcpu>;
-+		simple-audio-card,frame-master = <&sndcpu>;
-+		sndcpu: simple-audio-card,cpu {
-+			sound-dai = <&rcar_sound>;
-+		};
- 
--	sound_card: sound {
--		compatible = "audio-graph-card";
--
--		label = "rcar-sound";
--
--		dais = <&rsnd_port0>;
-+		sndcodec: simple-audio-card,codec {
-+			sound-dai = <&ak4613>;
-+		};
- 	};
- 
-+
- 	vbus0_usb2: regulator-vbus0-usb2 {
- 		compatible = "regulator-fixed";
- 
-@@ -454,12 +460,6 @@
- 		asahi-kasei,out4-single-end;
- 		asahi-kasei,out5-single-end;
- 		asahi-kasei,out6-single-end;
--
--		port {
--			ak4613_endpoint: endpoint {
--				remote-endpoint = <&rsnd_endpoint0>;
--			};
--		};
- 	};
- 
- 	cs2000: clk_multiplier@4f {
-@@ -795,18 +795,10 @@
- 		 <&audio_clk_c>,
- 		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
- 
--	ports {
--		rsnd_port0: port@0 {
--			rsnd_endpoint0: endpoint {
--				remote-endpoint = <&ak4613_endpoint>;
--
--				dai-format = "left_j";
--				bitclock-master = <&rsnd_endpoint0>;
--				frame-master = <&rsnd_endpoint0>;
--
--				playback = <&ssi0 &src0 &dvc0>;
--				capture  = <&ssi1 &src1 &dvc1>;
--			};
-+	rcar_sound,dai {
-+		dai0 {
-+			playback = <&ssi0 &src0 &dvc0>;
-+			capture  = <&ssi1 &src1 &dvc1>;
- 		};
- 	};
- };
--- 
-2.19.0
-