rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.9.2

This commit upgrades Linux BSP to v3.9.2 for the following changes:

[Kernel]
- Add support for RCKSEL clock selection.
- Fix pin functions of R-Car E3 according to H/W UM Rev1.00 errata.
- Fix warning of the make W=1 C=2.
- Identify R-Car M3 Ver.1.3.
- Add the big.LITTLE CAS scheduler fix patches.
- Fix MOD_SEL bit numbering for R-Car E3.

[Power Management]
- Fixup power-domains of 3DGE for R-Car E3 Ver.1.0 and add device
tree file for R-Car E3 Ver.1.0.

[Audio Driver]
- Fixup clock start checker.
- Resolve the problem that the noise is generated during long playback
with R-Car E3 Ebisu-4D board by kernel rebasing.

[Display Driver]
- Add function of suspend and resume to adv7511_drv.c and add hot plug
event function at resume in rcar_du_drv.c.
- Add depends on DRM_RCAR_DU to config DRM_RCAR_LVDS.
- Revert "drm: rcar-du: Fix legacy DT to create LVDS encoder nodes".
- Add clock function for LVDS PLL.

[Ethernet Driver]
- Decrease TxFIFO depth of Q3 and Q2 to one.
- Fix not to call phy_resume() if PHY is not attached and add toggling
phy reset if PHY is not attached.
- Revert "ravb: RX checksum offload" for communicating of Q-Tag VLAN
frame correctly.
- Resolved the problem that the S2RAM resume failed on R-Car E3
Ebisu-4D by kernel rebasing.
- Avoid unsupported internal delay mode for R-Car E3 and limit to
100Mbps.

[I2C Driver]
- Check bus state before reinitializing.

[IPMMU Driver]
- Fix crash on early domain free.
- Revert "arm64: defconfig: Enable QCOM_IOMMU" for suspending with
LTSI kernel.
- Correct whitelist devices assignment.

[PCIe Driver]
- Avoid PCI device removing/rescanning through sysfs triggers
a deadlock.

[PWM Driver]
- Avoid deadlock warning when removing PWM device.

[SD/MMC Driver]
- Fix card initialization failure in high speed mode.
- Add adjust HS400 offset by manual calibration mode and adjust HS400
offset by manual calibration mode for R-Car M3 Ver.1.3.

[USB2.0 Function]
- Add reset_control.
- Backport upstream patches to support OTG mode for R-Car E3.
- Make DMAC system sleep callbacks explicit.
- Add Super-Speed (b-device) support.

[Video Capture driver]
- Review adv748x driver for R-Car E3 Ebisu board and add option for
changing SD output route to TXA.
- Revert "rcar-vin: rcar-csi2: Add blank margin when caluculating bit
rate" and fix pixel rate values.
- Add CPG reset and release when using digital pin.

[RWDT Driver]
- Don't keep timer value during suspend/resume.
- Don't set divider while watchdog is running.

This also updates ADSP driver patches to adapt to the new
Linux version.

Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com>
Signed-off-by: Khang Nguyen <khang.nguyen.xv@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>

1 files changed, 0 insertions, 32 deletions

diff --git a/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0003-arm64-dts-r8a7795-salvator-x-Remove-Sound-Card.patch b/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0003-arm64-dts-r8a7795-salvator-x-Remove-Sound-Card.patch
deleted file mode 100644
index d068e6d..0000000
--- a/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0003-arm64-dts-r8a7795-salvator-x-Remove-Sound-Card.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From bcf876462ac57204cf9054ba6cc5d0703b9beb5e Mon Sep 17 00:00:00 2001
-From: Takeshi Kihara <takeshi.kihara.df@renesas.com>
-Date: Fri, 19 Oct 2018 11:48:48 +0900
-Subject: [PATCH 3/6] arm64: dts: r8a7795-salvator-x: Remove-Sound-Card
-
-This Patch Removes Sound-Card
-
-Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
----
- arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 6 ------
- 1 file changed, 6 deletions(-)
-
-diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
-index 6156bcc521b2..1f1920270aa4 100644
---- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
-+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
-@@ -117,12 +117,6 @@
- 	status = "okay";
- };
- 
--&sound_card {
--	dais = <&rsnd_port0	/* ak4613 */
--		&rsnd_port1	/* HDMI0  */
--		&rsnd_port2>;	/* HDMI1  */
--};
--
- &hdmi0 {
- 	status = "okay";
- 
--- 
-2.19.0
-