| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
- AM/FM receiver tools (si-tool)
- wifi wl18xx firmware
- Bluetooth tools
|
|
- Fix multichannel in rcar sound (optional compilation)
- add IMU driver
- enable new sensor drivers
- enalbe v3 usb3.0 firmware
- deploy Videobox dtb files
|
|
|
|
|
|
|
|
|
|
Do not reconfigure the link for eth0 interface.
This fixes the case when we use rootfs on NFS
|
|
The SOC_FAMILY is already different between H3ULCB and M3ULCB:
H3ULCB uses SoC r8a7795.
M3ULCB uses SoC r8a7796.
Hence, setting this value in h3ulcb.conf and m3ulcb.conf to allow
images to be built without setting SOC_FAMILY in local.conf.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This issue exists in some special environment.
Submodule can not be downloaded,
because HTTP/HTTPS lose their values during configure state.
Temporary solution is exporting those values in configure state.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates SRCREV for EthernetAVB drivers for below changes:
AVB Streaming Driver
- Fix DMA-API device driver frees DMA memory with different size.
- Fix problem of can setting out of range value of 'major' parameter.
MSE Core
- Add invalid calling state checking of MSE Adapter I/F in Kernel API.
- Fix overflow problem of timer delay value calculation
by some conditions of frame rate parameter (e.g. 1/30 fps).
- Reduce idling time in streaming pipeline process by queueing of
transmission request.
- DMA allocation via dma_alloc_coherent fails without CONFIG_OF.
- Fix overrun output area in parsing of u16/u32 values.
- Fix resource leakage at probe when error occurred.
- Fix problem of can setting out of range value of 'major' parameter.
MSE V4L2
- Reduce data concatenate processing of fragment data for MPEG2-TS
and MJPEG.
- If multiple open the same video device,
print out log message of "v4l2 device is opened".
MSE CVF MJPEG
- Fix problem of EOS marker position and progressed position
mishandling in packetize buffer if condition of small picture size
of MJPEG.
- Fix issue that stream transmission speed is too slowly if the
data size per picture is huge.
MSE CVF H264
- Fix problem that the setting value of bytes_per_frame parameter is
not effects if CVF H264 format.
- Fix issue that case of H264 transmission, the stream payload data
often corrupted if the data is high bitrate.
MSE IEC61883-4
- Fix problem that streaming stopping process stall at occurred
short of data.
- Fix problem that send the broken payload stream
if no PCR value in MPEG2-TS stream.
- Fix losing trailing data when streaming stopped on Talker.
MSE ALSA
- Fix losing trailing data when streaming stopped.
- In this version, there is a difference in audio timestamp phase
by each Listener device.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
The ADSP packages have been updated for following fixes:
- TDM Renderer framesize.
- EQZ->RDR.
- DMAC STAGE.
- SSI Setting.
- ADMAC Channel Swap.
- PDMA/ADMAC busy check.
- SRC busy check.
- SSI busy check.
Documents are also updated.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates VSP2 drv for following changes:
- Add __user attribute.
- Make local functions become static.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit modifies SRCREV of VSPM and VSPM I/F drv for below updates.
VSPM drv:
- Fix wrong argument of VSP_ROUND_UP.
- Simplify IS_VSP_CH(ch) macro.
- Remove unused variables.
- Use NULL instead of 0.
- Make local data/functions static.
VSPM I/F drv:
- Fix invalid memory access.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates MMNGR driver to v0.13 for following changes:
- Remove IPMMU(PMB) support due to hardware restriction.
- Add IPMMU(MMU) support for memory allocation.
- Fix compiler warnings.
- Add System Suspend-to-RAM support for IPMMU(MMU).
- Disable TLB function in IPMMU-VC0/VC1/VP0/VP1
due to hardware restriction.
- Add IPMMU(MMU) support for SSP.
It also modifies compile option of driver corresponding to new UM.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
New ICCOM pkgs have been released.
This patch updates MD5 values for ICCOM pkgs from v0.9.0 to v1.0.0.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates IPL and Secure Monitor to Rev1.0.15 rev3.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates u-boot to BSP v3.5.4 for following changes:
- Remove MSTP registers values rewriting process.
- Fix multiple declarations of DECLARE_GLOBAL_DATA_PTR.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates Linux BSP from v3.5.3 to v3.5.5
for following items:
Kernel core
- Add ZG clock divider support.
- Revert and fix about Suspend to RAM.
- Add DEVFREQ support for GSX.
- Add usb companion property in EHCI.
- Add USB3.0 peripheral device node.
- Use IPMMU(MMU mode) for IPMMU-VP and IPMMU-VC0/1
with R-Car H3 Ver.1.x,
for IPMMU-VP0/1 and IPMMU-VC0/1 with R-Car H3 Ver.2.0,
in IPMMUVC0 with R-Car M3.
- Add override support for the actual number of MMU contexts.
- Fix audio Mix support on DTSI.
Power Management
- Cleanup AVS driver.
- Update voltage for VDD_DVFS and VDD.
Audio driver
- Resolve 16bit/24bit capture noise problem by enabling
clock-frequency for both 4.1kHz/48kHz
and fixing possible NULL pointer dereference.
- Resolve playback problem of sampling rate 32kHz, 176.4kHz and
192kHz by enabling clock-frequency for both 44.1kHz/48kHz.
- Resolve “can’t get dma channel” error at the time of
unbind/bind by fixing up of_clk_add_provider() usage for multi clkout
and calling the missing of_clk_del_provider() when removing.
- Resolve 48kHz audio 1-20k sweep noise problem
by enabling clock-frequency 44.1kHz/48kHz.
- Merge rsnd_kctrl_new_m/s/e into rsnd_kctrl_new().
- Fix 24bit capture noise problem
by not using PDTA bit for 24bit on SSI.
- Request/Release DMA channel each time
for avoiding error of getting dma channel.
Display driver
- Use dma_map_sg_attrs to skip synchronization of the CPU cache.
- Add mode_fixup callback function.
- Control clock of bridge during S2RAM and change to control clock
via clock driver.
- Fix reserved register setting for R-Car for H/W manual update.
- Add null pointer check for brs option.
- Revert "drm: bridge/dw-hdmi: Add HDP interrupt disable
for suspend".
- Fix hierarchy of driver structure for clk-5p49x.
DMA Engine driver
- Revert dma pause function because it was rejected by upstream.
GPIO driver
- Revert and fix about Suspend to RAM.
- Add GP-1-28 port pin support for R-Car H3 Ver.2.0
because of H/W manual updating to Rev.0.54E.
Modify just PFC and DT.
SCIF/HSCIF driver
- Resolve system freezing.
SD/MMC driver
- Add initial setting of interrupt mask register.
- Fix command sequence at error detection.
- Fix “Wait for CBSY instead of SCLKDIVEN”.
- Fix processing when detecting SCC error and fix error handling
when issuing CMD23.
- Fix reset_hs400_mode.
- Fix problem that SDIO interrupt may be missed.
USB3.0 Function
- Add Role-change support.
- Add DMA support.
- Add basic function support.
USB2.0 Host driver
- Fix mouse connection time (2 second or more) when resuming.
USB3.0 Host driver
- Support for R-Car Gen3 USB 3.0 PHY for SSC function.
- Add R-Car Gen3 USB 2.0 clock selector PHY,
support for R-Car Gen3 USB 3.0 PHY.
Video Capture driver
- Add 2 lane support with rcar-csi2.c.
- Fix image alignment for setting pre clipping.
- Fix wait time for software reset in rcar-csi2.c
because of H/W manual updating to Rev.0.54E.
- Fix PHY initialization in rcar-csi2.c
because of H/W manual updating to Rev.0.54E.
- Fix PHTW register setting in rcar-csi2.c
because of H/W manual updating toRev.0.54E.
- Fix wait procedure usleep_range from msleep in adv7482.c.
- Fix channel get procedure.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
by default
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DISTRO_FEATURES, disabel x11 by default
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GPIO needs to be released by deserializer
|
Vladimir Barinov
Thao Nguyen
Grigory Kletsko