summaryrefslogtreecommitdiffstats
AgeCommit message (Collapse)AuthorFilesLines
2019-04-02rcar-gen3: u-boot: Update to version 3.9.3Duy Dang1-2/+2
This commit updates U-Boot SRCREV to Ver.3.9.3 for the following changes: - Increase off-on delay on the SD Vcc regulator. - Fix r8a779{5,6,90} DRIF conflict names by H/W UM 1.50 errata. - Apply upstream code related to mmc. - Add upstream description to DT files added by BSP. - Fix warning in writel() overflow in rcar_i2c.c. - Set environment variable containing CPU type. - Downgrade SD/MMC from UHS/HS200/HS400 modes before boot. - Unmount FS in do_fs_type(). - Support up to MMC HS200 mode with U-Boot. - Add DMA transfer address alignment check at writing. - Fix pinctrl definition according to H/W UM Rev.1.00 and errata. - Force mmc reinit when no card present. - Make DMA transfer end bit configurable and add 1uS delay after DMA completion on older IPs. - Add function to activate with suitable DT and add Enable MULTI_DTB_FIT. Change-Id: I958f86c16e7558ac51b40e68f611b7f20748877c Signed-off-by: Duy Dang <duy.dang.yw@renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2019-04-02rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.9.4Khang Nguyen2-4/+4
This commit upgrades Linux BSP to v3.9.4 for the following changes: - Fix power domain for FCPCS of r8a77965 in the device tree according to H/W UM Rev.1.50 correction in the future. - Rename AVB_AVTP_MATCH and AVB_AVTP_CAPTURE pin function definitions of r8a77990 according to H/W UM Rev.1.50 correction in the future. - Revert the patch of r8a77990 pinctrl about MOD_SEL1 bit31 and bit30 according to H/W UM errata for Rev.1.00. - Fix cpg_sd_clock_round_rate return value. - Rename some pin function and cpg definition according to H/W UM Rev.1.50 errata. - Rename SEL_ADG_B to SEL_ADGB and rename SEL_ADG_C to SEL_ADGC according to H/W UM Rev.1.50. - Fix SCIF5 DMA channels according to H/W UM Rev.1.50. - Fix clock and reset for ivdp1c according to H/W UM Rev.1.50. - Add support for R-Car M3 ES3.0. - Fix MMC cannot probe by modprobe command after S2R issue. Change-Id: I12901a91f2e6ebaf5879456faeb5f9d3baad6f32 Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Duy Dang <duy.dang.yw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2019-04-01rcar-gen3: machine: Add device tree for M3 Ver.3.0Khang Nguyen1-0/+1
This commit adds device tree for M3 Ver.3.0. Change-Id: Ifbca4171a00a25e00f01acc327222c952d070bcc Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2019-04-01rcar-gen3: Add support M3NULCB boardYusuke Goda24-4/+2511
M3NULCB board specifications: R-Car M3-N Ver.1.1 DDR 2GiB eMMC 8GB(KLM8G1GESD-B04P) Change-Id: Ie857f76d7c96cd6e9a9196ce9bc27d98e878b161 Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com> Signed-off-by: Duy Dang <duy.dang.yw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: README: Add build requirementRenesas-Yocto-v3.15.0Duy Dang1-0/+6
This commit adds build requirement of git configuration for user name and email to the README file. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: conf: Add DVD Encryption Library configurationDuy Dang8-0/+16
This commit adds DISTRO_FEATURES_append = " dvd_encryption_library" to build DVD Encryption Library package. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: copyscript: Update MD5SUM for OMX Video packagesDuy Dang1-16/+16
This commit updates MD5SUM list for OMX Video packages. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: copyscript: Update MD5SUM for OMX Audio packagesDuy Dang1-13/+13
This commit updates MD5SUM list for OMX Audio packages. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: copyscript: Update MD5SUM for CMS packagesDuy Dang1-3/+3
This commit updates MD5SUM list for CMS packages. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: cms-user-module: Update library versionDuy Dang1-6/+6
This commit updates library version of CMS module from 1.9.0 to 2.0.0. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: image: Add DVD Encryption Library to MMP ImageDuy Dang2-0/+9
This commit adds DVD Encryption Library to build in MMP configuration. This package uses DISTRO_FEATURES_append = " dvd_encryption_library" to be built. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: copyscript: Add DVD Encryption Library packageDuy Dang2-4/+12
This commit adds DVD Encryption Library to use with copy proprietary software script. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Thuy Tran <thuy.tran.xh@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: dvd-encryption-module: Add new recipeDuy Dang1-0/+53
This commit adds a new recipe for DVD Encryption Library package. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: openavnu: Fix do_configure errorDuy Dang1-0/+4
This commit fixes the error when re-build openavnu: | aarch64-poky-linux-gcc: error: unrecognized argument in option '-mcmodel=kernel' | aarch64-poky-linux-gcc: note: valid arguments to '-mcmodel=' are: large small tiny | aarch64-poky-linux-gcc: error: unrecognized command line option '-mno-red-zone'; did you mean '-fno-regmove'? The error comes from cleaning other unnecessary modules which have some make flags for x86_64 architecture. In AVB software, Renesas BSP uses some daemons (mrpd maap gptp shaper) only. Hence, this fix makes do_configure not to clean all AVB modules to avoid the above error. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: gstreamer: Update SRCREV to the latest versionDuy Dang1-1/+1
This commit updates SRCREV of gstreamer to follow the latest version for the following change: [omxvideodec] - Query drain before inactivate omxbufferpool to avoid out standing buffers Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: gles-module: Replace soft paths in source directory with hard pathsTan Nguyen1-24/+24
Soft paths in source directories may cause error when changing values of variables in these paths. Hence, this commit changes soft paths in source install directories to hard paths. Signed-off-by: Tan Nguyen <tan.nguyen.wh@renesas.com> Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: copyscript: Update MD5SUM list for ADSP packagesDuy Dang1-3/+3
This commit updates MD5SUM list for ADSP packages. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: vspm: Update SRCREV to follow the latest versionDuy Dang4-80/+3
This commit updates SRCREV of vspm and vspmif driver to follow the latest version for the following changes: [vspmif_drv] - Fixed an issue where vspmif could crash. [vspmif_lib] - To correspond boards that do not support Full HD. [vspm_drv] - Fix VI6_HGO/HGT_WBUFS setting from CPU write to Display List. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: EtherAVB: Update SRCREV to the latest versionDuy Dang2-2/+2
This commit updates SRCREV of EtherAVB driver and applications to follow the latest version for some changes as below: [avb-mse] - Core: Add filter of outliers in create avtp timestamp - Core: Fix problem that the streaming might be stalled - Core: Fix missing bit mask at difference calculation of M2TS timestamp [avb-applications] - avdecc: make: fix cmake error if not doing submodule update - avblauncher: update example script affect by changed MSE usage Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: mmngr: Update SRCREV to follow the latest versionDuy Dang1-1/+1
This commit updates SRCREV of MMNGR modules to the latest version for the following changes: - Improve error handling for import phases and close() function about Refcount of dmabuf in MMNGRBUF. - Add support for Linux v4.14-LTSI. - Remove unnecessary check when parsing reserved memory regions in DT - Disable IPMMU TLB cache function in E3 Ver.1.x due to hardware restriction. - Add E3 Ver.1.1 support. - Add error handling for mm_probe() function. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: optee-os: Update SRCREV to follow the latest versionDuy Dang1-1/+1
This commit updates SRCREV of optee-os recipe for these changes: - Fix the MMU configuration of shared memory. - Merge the following pull request. https://github.com/renesas-rcar/optee_os/pull/2 - Change a cipher method of AES-CTR from a block cipher to a stream cipher. - Fix exclusive controls of asymmetric encryption. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: IPL: Update SRCREV to follow the latest versionDuy Dang1-1/+1
This commit updates SRCREV of IPL and Secure Monitor to Rev2.0.0 for these changes: [IPL] - Update DDR setting for E3(rev0.11). - Change the condition of data transfer end of SCIF transfer. - Modify address area in the DDR memory config log output. - Update H3 Ver.3.0 QoS setting rev.0.09. - Update E3 Ver.1.0 QoS setting rev.0.04. - Update H3 Ver.2.0 QoS setting rev.0.20. - Update H3 Ver.3.0 QoS setting rev.0.10. - Update M3 Ver.1.1 QoS setting rev.0.18. - Update M3N Ver.1.1 QoS setting rev.0.08. - Update E3 Ver.1.0 QoS setting rev.0.05. - Modify load destination variable of the Cert Header to static. - [H/W Restriction No.100]: + Disable TLB function of IPMMU cache on E3 Ver.1.1. + Disable TLB function of IPMMU-PV0 cache on E3 Ver.1.x. [Secure Monitor] - Add API for getting DRAM capacity information. - Change the execution timing of system RAM copy process to BL31 startup. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: u-boot: Drop SoC name in srec filesKhang Nguyen1-0/+1
This commit updates do_deploy function to drop the SoC name when deploying srec files, the purpose is to keep the legacy name of U-Boot build results. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-20rcar-gen3: u-boot: Update SRCREV to version 3.9.1Duy Dang1-2/+2
This commit updates SRCREV of U-Boot to version 3.9.1 for the following changes: - Generate fitting memory map on R-Car Gen3, fix protection area access error and fix to enable icache early in R-Car Gen3. - Add module clock stop before OS startup. - Reorder TMIO clock handling. - Do not issue CMD 6 on SD 1.00 and SD 1.01. - Fix protection area access error at Cortex-A53. - Avoid unsupported internal delay mode for R-Car E3 and limit to 100Mbps. - Revert "net: Fix cache misalignment message after network load operations" - Add "usb_pgood_delay" to the default environment variable. - Fix warning of the make W=1 C=2. - Resolve the problem that the eMMC read of the environment setting value may fail at startup. - Add vbus-supply regulator support. - Resolve the problem that the SD card (UHS, etc.) isn’t recognized. - Fix MOD_SEL bit numbering for R-Car E3. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xv@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-19rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.9.2Duy Dang29-3301/+3493
This commit upgrades Linux BSP to v3.9.2 for the following changes: [Kernel] - Add support for RCKSEL clock selection. - Fix pin functions of R-Car E3 according to H/W UM Rev1.00 errata. - Fix warning of the make W=1 C=2. - Identify R-Car M3 Ver.1.3. - Add the big.LITTLE CAS scheduler fix patches. - Fix MOD_SEL bit numbering for R-Car E3. [Power Management] - Fixup power-domains of 3DGE for R-Car E3 Ver.1.0 and add device tree file for R-Car E3 Ver.1.0. [Audio Driver] - Fixup clock start checker. - Resolve the problem that the noise is generated during long playback with R-Car E3 Ebisu-4D board by kernel rebasing. [Display Driver] - Add function of suspend and resume to adv7511_drv.c and add hot plug event function at resume in rcar_du_drv.c. - Add depends on DRM_RCAR_DU to config DRM_RCAR_LVDS. - Revert "drm: rcar-du: Fix legacy DT to create LVDS encoder nodes". - Add clock function for LVDS PLL. [Ethernet Driver] - Decrease TxFIFO depth of Q3 and Q2 to one. - Fix not to call phy_resume() if PHY is not attached and add toggling phy reset if PHY is not attached. - Revert "ravb: RX checksum offload" for communicating of Q-Tag VLAN frame correctly. - Resolved the problem that the S2RAM resume failed on R-Car E3 Ebisu-4D by kernel rebasing. - Avoid unsupported internal delay mode for R-Car E3 and limit to 100Mbps. [I2C Driver] - Check bus state before reinitializing. [IPMMU Driver] - Fix crash on early domain free. - Revert "arm64: defconfig: Enable QCOM_IOMMU" for suspending with LTSI kernel. - Correct whitelist devices assignment. [PCIe Driver] - Avoid PCI device removing/rescanning through sysfs triggers a deadlock. [PWM Driver] - Avoid deadlock warning when removing PWM device. [SD/MMC Driver] - Fix card initialization failure in high speed mode. - Add adjust HS400 offset by manual calibration mode and adjust HS400 offset by manual calibration mode for R-Car M3 Ver.1.3. [USB2.0 Function] - Add reset_control. - Backport upstream patches to support OTG mode for R-Car E3. - Make DMAC system sleep callbacks explicit. - Add Super-Speed (b-device) support. [Video Capture driver] - Review adv748x driver for R-Car E3 Ebisu board and add option for changing SD output route to TXA. - Revert "rcar-vin: rcar-csi2: Add blank margin when caluculating bit rate" and fix pixel rate values. - Add CPG reset and release when using digital pin. [RWDT Driver] - Don't keep timer value during suspend/resume. - Don't set divider while watchdog is running. This also updates ADSP driver patches to adapt to the new Linux version. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xv@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-19rcar-gen3: machine: Add Ebisu 1.0 device treeDuy Dang1-0/+2
This commit adds more device trees for Ebisu 1.0 and Ebisu-4D 1.0: - r8a77990-es10-ebisu-4d.dts - r8a77990-es10-ebisu.dts Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-19rcar-gen3: machine: Build multiple U-Boot binaries for Salvator-X/XSDuy Dang1-6/+11
This commit enables U-Boot configuration to build all binaries for Salvator-X and Salvator-XS boards. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Thuy Tran <thuy.tran.xh@renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: conf: Enable PAM distro feature for BSP minimalKhang Nguyen8-0/+24
This commit enables PAM distro feature for BSP minimal configurations, its target is to support LTP test on core-image-minimal. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: conf: Change default SoC in local-ltp.conf to r8a7795Khang Nguyen2-4/+4
This commit changes the default SoC in local-ltp.conf to r8a7795. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: conf: Remove H3_OPTION from build configurationsKhang Nguyen10-80/+0
IPL and U-boot were built all binaries of H3 DRAM configurations at one time. Hence, H3_OPTION was not used anymore. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: conf: Enable USB3H as default for EbisuKhang Nguyen8-8/+8
This commit enables USB3H as default for Ebisu. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: path-common: Using operator ?= for RENESAS_DATADIRRonan Le Martret1-1/+1
RENESAS_DATADIR must be able to be overwritten. Signed-off-by: Ronan Le Martret <ronan.lemartret@iot.bzh> Signed-off-by: Thuy Tran <thuy.tran.xh@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: iccom-user-module: Remove iccom-control requirementDuy Dang1-1/+0
The iccom user module recipe requires iccom-control.inc file which defines USE_ICCOM variable, but nothing uses it. This commit removes that requirement. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: iccom-tp-user-module: Add new sample test programKhang Nguyen1-0/+5
This commit modifies recipe to add a new sample test program binary (sample_pvconv) to rootfs. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: gstreamer: Update SRCREV to follow the latest versionKhang Nguyen3-3/+3
This commit modifies gstreamer recipes for following updates: [gst-omx] - Fix issue of seeking with dynamic change in dmabuf mode. - Support dynamic change in src pad. - Move initial and free arrays which used for use-dmabuf's handling from init and finalize to start and stop. - Improve log and free memory in error case. [gst-plugins-good] - Static analysis: Remove duplicated condition. [gst-plugin-vspfiler] - Don't reinitialize colorimetry table if it has already been set up. - Fix memory leak. - Do not set colorimetry to out structure containing in format. - Modify variable type. - Fix initialization of GValue. - Remove last commma in enum. - Change position of declaration to beginning of the function. - Change variable name to avoid duplication of declarations. - Fix copyright years in header. - Intersect format in fixate_caps(). - Fix possible segmentation fault during caps fixation. - Support colorimetry negotiation. - Add option for setting input buffer color range. - Support encoding and color range setting. - Reduce arguments of set_vsp_entities(). - Modify transfrom_caps() for more accurate operation. - Delete unnecessary variable in transform_caps(). - Modification of variable type. - Measure for converting odd size rgb buffer to yuv. - Implement measure for odd size yuv buffer input. - Change the order of linking and set format. - Delete unnecessary wpf linking. - Deactivate input bufferpool before remake. - Don't make new output pool when it exists already. - Change the state of flag of playing when stop streaming. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: gles-user-module: Add depends on mesa to gles-user-moduleRonan Le Martret1-0/+3
The populate_sysroot of gles-user-module must depends on the populate_sysroot of the virtual/mesa, because header from gles-user-module depends on the header from virtual/mesa. Signed-off-by: Ronan Le Martret <ronan.lemartret@iot.bzh> Signed-off-by: Thuy Tran <thuy.tran.xh@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: gles-user-module: Remove redundant "virtual/egl" in PROVIDESDuy Dang1-1/+1
gles-user-module provides virtual/egl in order to use in core-image-x11 which is not supported anymore, virtual/egl is now provided by libegl. This commit removes virtual/egl in PROVIDES list. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: avb-applications: Remove avb-control.inc requirementDuy Dang1-1/+0
This recipe requires avb-applications.inc which defines USE_AVB variable, but nothing uses it. So it is safe to remove that requirement. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: gstreamer-omx: Add RDEPENDS on omx-user-moduleRonan Le Martret1-1/+2
gstreamer-omx should RDEPENDS on omx-user-module, and not on libomxil. Signed-off-by: Ronan Le Martret <ronan.lemartret@iot.bzh> Signed-off-by: Thuy Tran <thuy.tran.xh@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: adsp-module: Use distro features checkDuy Dang2-4/+8
This commit changes to use distro_features_check class to show the correct error message when building adsp modules without its distro feature in local.conf: | ERROR: Nothing PROVIDES 'adsp-fw-module' | adsp-fw-module was skipped: missing required distro feature 'adsp' (not in DISTRO_FEATURES) The USE_ADSP variable is not used anymore in the recipes. It is safe to remove adsp-control.inc requirement. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: dvd-user-module: Remove redundant codeKhang Nguyen1-1/+1
This commit removes a redundant code in dvd-user-module recipe. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: cms-user-module: Upgrade library versionsKhang Nguyen1-6/+6
This commit upgrades library versions as below: libcmsbcm.so.1.8.0 upgrades to libcmsbcm.so.1.9.0 libcmsblc.so.1.8.0 upgrades to libcmsblc.so.1.9.0 libcmsdgc.so.1.8.0 upgrades to libcmsdgc.so.1.9.0 Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: copyscript: Update MD5SUM for CMS packagesKhang Nguyen1-3/+3
This commit updates MD5SUM for new CMS packages. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: copyscript: Update MD5SUM for video packagesKhang Nguyen1-16/+16
This commit updates MD5SUM for new video packages. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: copyscript: Update MD5SUM for audio packagesKhang Nguyen1-13/+13
This commit updates MD5SUM for new OMX audio packages. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: copyscript: Update MD5SUM for ADSP packagesKhang Nguyen1-3/+3
This commit updates MD5SUM for new ADSP packages. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: vspmif-module: Correspond boards that do not support Full HDKhang Nguyen2-0/+77
This commit applies a fix patch to correspond boards that do not support Full HD. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: V4L2/VSPM: Update SRCREV to follow the latest versionKhang Nguyen4-4/+4
This commit updates V4L2/VSPM SRCREV for following updates: [vsp2driver] - Support the expression for color space conversion. - Fix minimum input pixel size for RGB format to 1 pixel. [vspm_drv] - Move function definitions out of vspm_cmn.h. - Fix macro name to register name. [vspmif_drv] - Convert user_data and cb_func to user pointers. - Remove __user macro from the variable declaration. [vspmif_lib] - Add prototypes for VSP Manager API. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: weston: Update SRCREV to follow the latest versionKhang Nguyen1-1/+1
This commit updates SRCREV of weston for following items: [v4l2-renderer] - Use uint8_t* for variables to be operated by pointer. - Apply to "U" suffix constatnt of unsigned type. - Fix according to static code analysis tool. - Improve attaching shm buffer. - Use stride of shm buffer, not of KMS BO. - Remove bytesused from v4l2_renderer_plane. - Use length instead of byteused. - Set -1 when closing dmabuf. - Remove unused members in v4l2_surface_state. - Remove unused member bpp. - Free buffers queued into RPF which is disabled. - Allow set image width/height to 1 for input VSP in using RGB. - Skip rendering the surface which buffer isn't attached. - Expand damage region when using YUV444 and YVU444 color format. - Expand damage region when using multi sample pixels format. - Make opaque region the same as non-opaque. - Don't release dmabuf buffer immediately when client release buffer. [compositor-drm] - Use bool type for flag for using v4l2-renderer. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: kernel-module-qos: Update SRCREV for QoS driverKhang Nguyen1-1/+1
This commit updates QoS driver SRCREV for following item: [qos_drv] - Feedback of static analysis tool result. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>