Age | Commit message (Collapse) | Author | Files | Lines |
|
|
|
The patch 0035-* breaks regulators on KF board.
As a result the Multichannal audio was broken
|
|
Use gpiod instead of gpio regulator in LVDS drivers
This is ruquired to remove patch:
0035-regulator-fixed-probe-after-i2c.patch
The above patch breaks regulators support on Kingfisher board
|
|
Remove these helper patches since it is possible to
adjust cameras feature in kernel command line now
|
|
1) unify TI9X4 deseializers (TI954, TI964)
2) add V3MZF board
3) shorten deserilziers name in Kconfig/Makefile
4) add camera sensor AR0220
|
|
|
|
|
|
This is tested on KF + H3 ws2.0
|
|
Fix IMP sizes/names/sysc
Add new IMP blocks
|
|
1) add poc-delay field that introduces extra delay after apply
POC-supply power. Default value is 50ms
2) add stability fixes for AP0101-AR014x cameras:
read OTP_ID runtime (do not use cached value at kernel boot time,
since it may read unstable/incorrectly)
|
|
1) replace gpio-hog power with POC-supply regulator on
VideoBox and VideoBox2 boards
2) remove sensor-delay filed form dts if it is 0 and if it
is replaced with POC-supply
|
|
1) Add GETHER in uboot/kernel
2) Condor board: setup as default interface
|
|
This fixes warn message form spidev driver
|
|
|
|
1) add dvp_order module parameter
2) add max_height, max_width params
This will allow override default dts params using kernel command line:
f.e.:
" ov106xx.dvp_order=2"
or
" ov106xx.max_width=1280 ov106xx.max_height=966 max9286.gpio_resetb=4 max9286.active_low_resetb=1 max9286.fsync_period=3200000"
|
|
1) add spidev function on MSIOF
2) set MSOIF1 master and MSIOF slave on V3MSK VideoBoxMini
|
|
|
|
1) add uboot R-Car V3H SoC (r87798) and V3H based Condor board
2) add kernel R-Car V3H SoC (r87798) and V3H based Condor board
|
|
Remove this since Eagle does not have USB
|
|
1) enable in kernel TMU,CMT timers via Kconfig
2) add missed timer tmu0
|
|
1) remove dallas rtc since conflicts address with clk generator on ULCB at 0x68
2) remove sata
3) fix can: add termination resistor and pull-ups
|
|
This adds reading fused from AR014x sensors
|
|
1) Fix AP0101+MAX96705 cameras by control FSINC
These cameras require GMSL inititialization only with FSYNC disabled
2) add more module options: gpio_resetb and active_low_resetb
3) change automatic buffer fsync_mode_default to static
|
|
This add timers: TMU, TPU, CMT
Fix V3M thermal sensor
Add CANFD on Eagle board
|
|
|
|
|
|
This is necessary to have uinput since there is no other ability to have
input device (no USB)
|
|
|
|
1) support AP0101+AR014x cameras
2) support DVP bus reverse inside VIN:
using kernel parameter "rcar_vin.lut_reverse=1"
This is needed for cameras that can't do bus reverse.
MAX9286 does DVP reverse and send data via CSI2.
Some cameras can't do reverse back, hence we can do revers in RCAR VIN.
This is applciable only for 8bit buses: raw8, yuyv8, rgb888
3) support serializers in HIGH-Immunity mode alighend with legacy mode.
MAX96705 can do legacy and HIM modes.
MAX9271 can do only leagacy mode.
4) support crossbar feature for MAX96705
This is DVP bus reordering in serilizer.
5) support passing kernel parameters to max9286 driver.
This allows to conect all supported cameras to ADAS boards without
changing DTS file, but add only parameters to kernel command line in uboot bootargs
F.e.:
max9286.him=1 max9286.vsync=0 max9286.fsync_period=3200000
or
max9286.vsync=0 max9286.fsync_period=2500000 rcar_vin.lut_reverse=1
The default setup (no changes needed) is for IMI RDCAM20/21 cameras.
6) change name of max9286 driver, since max96705 is also supported by
this driver:
max9286-max9271 -> max9286
|
|
This adds manual wight balance control for ov490/10640 sensor.
|
|
This avoid adding extra line in /etc/securetty for RDRIVE, since
first serial device was SCIF2 (ttySC0) and the SCIF1 is second (ttySC1).
This patch removes tty on SCIF2 and enbles only SCIF1 console.
Hene it is possible to use common ULCB rootfs without changing of securetty.
|
|
MAX9286 may result CSI2 stream losing the last byte.
This observed rarely with only 1 cmaera connected to quad
deserializer.
This patch fixes this issue
|
|
V3M supports up to 1000MBPS without ISP.
Add 700MBPS speed to TI96x deserializer and set
default speed in dts to 700MBPS.
|
|
Add Eagle expandtion Function board:
- add eMMC
|
|
Sync with latest Renesas Japan develpoment
|
|
Remove backported DMAC patches since they crash ravb.
Test case: ping flood from host side
|
|
- Release GP6_08 and input pins used on gpio expander U11, since this pin
is used by IPL for access CPLD during gpio bitbang i/f to implement reset
- fix typo in i2cswitch node name
|
|
|
|
- Backport RCAR DMAC fixes from upstream
- Reeneable DMA for SCIF0 on R8A7797
|
|
|
|
|
|
Add OV10640 OTP memory BANK#1 flashing script
If BNAK#0 isempty then fall into BANK#1 reading in kernel driver.
Also add tool for flashing BANk#1
BANK#1 is customer area
|
|
|
|
|
|
1) use POC regulators in driver and power cameras one after one
2) set sensors reset during POC channels setup
3) fix wizard setup for ov490 based caemras by waiting it's firmware
start all internal apps
4) support AR0132 with MAX9286
5) due to stability fixed then increase i2c bus speed on Videobox Mini
6) support MAX96705 serializer with MAX9286
|
|
|
|
|
|
|
|
|
|
- Support IMR/VSP/DRM for V3M
- Add packeges to use IMR-DRM demo
|