Age | Commit message (Collapse) | Author | Files | Lines | |
---|---|---|---|---|---|
2017-09-20 | switch to 2.23.0 bsp | 1 | -10/+0 | ||
2017-08-28 | Add V3MSK and deploy legacy KF images | 1 | -0/+14 | ||
2017-08-26 | Add V3M Eagle machine | 1 | -0/+2 | ||
2017-08-15 | revert gpio-max732x-set-gpio-ouput-low-at-init | 1 | -1/+0 | ||
This patch introduces bug | |||||
2017-08-11 | Gen3: disable autosuspend for SMSC usb hubs | 1 | -0/+1 | ||
Thisis a workaround for R-Car Gen3 XHCI | |||||
2017-08-10 | Kingfisher: enable PCM audio between CPU and BT module | 1 | -0/+1 | ||
Add dummy driver for wl18xx PCM. Update dtb's. Update pulseaudio config. Also add ofono-test. | |||||
2017-08-10 | KF: fix DU RGB flickering, remove SDR50/104 | 1 | -0/+2 | ||
1) fix DU RGB port flickeringby presclaing clock in VC5 2) limit clock for DU RGB in driver adv7511 to 100Mhz this is according to Gen3 manual limitation for this DU port 3) update README 4) remove SDR50/104 from onboard KF | |||||
2017-08-09 | Sound: ak4613: suppress warning during pulseaudio probe | 1 | -0/+1 | ||
2017-08-09 | KF: ADV7511 edid fixes, i2c2 speed 400khz, hsusb ws2.0 enable | 1 | -0/+1 | ||
1) fix edid get via adv7511 2) increase i2c2 speed from 100 to 400khz sine #1 fixed 3) enable hsusb for H3 ws2.0 | |||||
2017-08-06 | LVDS: workaroundpatch is not needed anymore | 1 | -1/+0 | ||
optional compilation for Cogent firmware is not needed anymore since driver supports both firmware: Cogent and Vendor | |||||
2017-08-02 | Kingfisher: BT: use proper way to get shutdown gpio | 1 | -0/+1 | ||
2017-08-01 | Fix build error: kf-v1 does not present anymore | 1 | -3/+0 | ||
2017-07-31 | VIN: fix S_SELECTION (S_CROP IOCTL) | 1 | -0/+1 | ||
2017-07-28 | Kingfisher V3: update m-channel sound support (fix) | 1 | -1/+0 | ||
2017-07-28 | Kingfisher V3: update m-channel sound support | 1 | -0/+1 | ||
On V3 m-channel codec is moved to SSI34, so only minor update of sound driver is necessary. | |||||
2017-07-27 | LVDS: optional compilation for Cogent firmware | 1 | -0/+1 | ||
This allows to use Cogent generated frimware for LVDS cameras (ov490+0v10640). | |||||
2017-07-27 | Kingfisher V3 update | 1 | -0/+1 | ||
- correct SDHI3 for uhs mode enabled - add regulators to pcie-rcar - enable rpi camera | |||||
2017-07-15 | lvds/VB/KF, cma memory | 1 | -0/+3 | ||
- KF: set max9286 i2c address to 0x2c - disable eMMC on r8a7795-es1 - max7325: initialize pins to output-low - enlarge cma memory region on ulcb | |||||
2017-07-14 | add ov5642, fix DVP in VIN | 1 | -1/+3 | ||
- add ov5642 driver - fix parallel interfacein VIN - enable CMOS cameras on Kingfisher | |||||
2017-07-14 | KF: fix high rate renedering on adv7511 | 1 | -0/+1 | ||
LVDS DU does not support high freq | |||||
2017-07-14 | Pack patches: put all ADAS boards patches on one | 1 | -14/+3 | ||
2017-07-13 | Kingfisher: add multichannel audio, IMU driver | 1 | -0/+5 | ||
- Fix multichannel in rcar sound (optional compilation) - add IMU driver - enable new sensor drivers - enalbe v3 usb3.0 firmware - deploy Videobox dtb files | |||||
2017-07-13 | add H3 Videobox board | 1 | -0/+1 | ||
2017-07-10 | I2C switch: fix PCA954x i2c expander access | 1 | -0/+1 | ||
2017-06-01 | Kinfgisher: add USB modem, RaspberryPi camera | 1 | -0/+1 | ||
2017-05-30 | Kingfisher V1 update | 1 | -0/+4 | ||
2017-05-25 | KF V1 deploy dtb images | 1 | -0/+3 | ||
2017-05-24 | Add KF V1 board | 1 | -0/+1 | ||
2017-05-19 | uboot: add Hyperflash access | 1 | -0/+1 | ||
2017-05-17 | Fix dtb list | 1 | -2/+1 | ||
2017-05-17 | Initial commit for ADAS boards support in 2.19.0 | 1 | -0/+75 | ||