| Age | Commit message (Collapse) | Author | Files | Lines | |
|---|---|---|---|---|---|
| 2018-03-27 | VB2: disable autosuspend for TUSB8041 hub |   Andrey Gusakov | 2 | -11/+18 | |
| 2018-03-26 | VB2: enable Kvaset USB/CAN | Andrey Gusakov | 1 | -0/+1 | |
| 2018-03-26 | VB2: fix can2 and can3 coldstart probe fail | Andrey Gusakov | 3 | -24/+87 | |
| Reset pins of external mcp251x can adapters are driven by i2c gpio extender pins which is probed later than mcp251x. So at probe time reset pins are low causing probe fail. Add reset-gpio support to driver. Adjust VB2 dtb. | |||||
| 2018-03-21 | ULCB-KF: ULCB has cs2000 with 100khz i2c clk |   Vladimir Barinov | 1 | -3/+1 | |
| ULCB has CS2000 onboard with maximum allowed i2c clk rate 100khz. Hence the parent (KF) must follow this restriction. | |||||
| 2018-03-21 | V3MZF: update dts file to use CS1 in hardware | Vladimir Barinov | 1 | -1/+2 | |
| 2018-03-16 | Build fix for previouse commit | Vladimir Barinov | 1 | -3/+3 | |
| 2018-03-15 | V3MSK VBM and V3MZF: update spi slave after fixes | Vladimir Barinov | 1 | -10/+7 | |
| 1) Use h/w spi chip-select frame instead gpio 2) update filed name for spi slave device | |||||
| 2018-03-15 | SPI: fix perfromance and fix SPI slave packets loss | Vladimir Barinov | 2 | -36/+305 | |
| - this fixes SPI performance when small chunks are used during transfer under heavy cpu load - fix spi slave<->master packets loss under heavy load | |||||
| 2018-03-13 | AR0132: add FLIP fix | Vladimir Barinov | 1 | -1/+1 | |
| 2018-03-12 | Add V3H VIP devices support. |   Andrey Dolnikov | 4 | -0/+197 | |
| 2018-03-07 | VB2: enable USB23 (labeled "USB2") on H3 ES20 | Andrey Gusakov | 1 | -5/+31 | |
| On ES1.1 this port is USB3.0. On ES2.0 this port is USB2.0 | |||||
| 2018-02-26 | V3H: Add VideoBoxMini and VideoBoxMini V2 boards | Vladimir Barinov | 3 | -6/+607 | |
| This adds V3HSK exapsion boards | |||||
| 2018-02-26 | V3MZF: add eMMC in kernel | Vladimir Barinov | 1 | -6/+44 | |
| 2018-02-26 | Enable thermal sensor driver for V3M | Andrey Dolnikov | 1 | -0/+1 | |
| 2018-02-26 | Fix typo | Vladimir Barinov | 1 | -1/+1 | |
| This fixes the typo during patch update | |||||
| 2018-02-26 | V3M Eagle: remove du_pins htat are not used | Vladimir Barinov | 1 | -8/+1 | |
| Remove dependencey on RGB pins since theare are not used on Eagle board. The LVDS interface is used. | |||||
| 2018-02-26 | Add V3H Starter Kit board | Vladimir Barinov | 4 | -6/+421 | |
| This adds V3H Starter Kit board support | |||||
| 2018-02-26 | V3M: Support ES1.0 SoC | Vladimir Barinov | 2 | -18/+325 | |
| 2018-02-26 | V3M VideoBoxMiniV2: set POCx-gpios instead POCx-gpio | Vladimir Barinov | 1 | -4/+4 | |
| It is already used for all POCx-gpios and not POCx-gpio. Both are functonal for 1 gpio used. This change just syncs with others. | |||||
| 2018-02-26 | V3M VidoeoBoxMiniV2: user proper compatible | Vladimir Barinov | 1 | -1/+1 | |
| the "spidev" is prohibbited to use for binding | |||||
| 2018-02-26 | V3MSK: add PMIC | Vladimir Barinov | 1 | -5/+36 | |
| This add DA9063 PMIC on V3MSK I2C0 bus | |||||
| 2018-02-26 | V3MSK and Condor have 2GB memory | Vladimir Barinov | 1 | -2/+2 | |
| 2018-02-26 | IMR: push rotation-scaling-enable flag up | Vladimir Barinov | 1 | -1/+1 | |
| The flag number 8 is already busy with another option, hence push RSE flag up | |||||
| 2018-02-26 | V3M/V3H: sysc workaround for power down, cpu clock fixup | Vladimir Barinov | 5 | -78/+460 | |
| This adds SYSC workaround for power domains power down sequence on V3M/V3H and add cpu clock fixup on V3H. Also add VisionIP nodes and fix VSP i/f on V3H | |||||
| 2018-02-26 | V3M VBM V2: deploy dtb | Vladimir Barinov | 1 | -0/+1 | |
| Deploy dtb file for V3M VideoBoxMini V2 board | |||||
| 2018-02-26 | V3M Eagle: add PMIC | Vladimir Barinov | 2 | -4/+39 | |
| This adds PMIC devices (regulator,wdt,rtc) on Eagle | |||||
| 2018-02-26 | Adds RSE support for V3H IMR | Vladimir Barinov | 3 | -1/+331 | |
| This adds RSE support for V3H IMR | |||||
| 2018-02-26 | Add V3M based Video Box Mini V2 board | Vladimir Barinov | 2 | -39/+126 | |
| This cleans up VideoBoxMini board and add VideoBoxMini V2 board | |||||
| 2018-02-26 | Add OV2775 camera | Vladimir Barinov | 1 | -55/+2425 | |
| This adds OV2775 sensor connected to TI953 seriliazer | |||||
| 2018-02-26 | VideoBoxMini: fix POC sequence typos | Vladimir Barinov | 1 | -6/+6 | |
| This fixes POC sequence on following boards: - V3MSK + VideoBoxMini - ULCB + VideoBoxMini | |||||
| 2018-02-26 | Fix merge conflict | Vladimir Barinov | 1 | -1/+1 | |
| Fix build fail | |||||
| 2018-02-26 | Add V3MZF target | Vladimir Barinov | 3 | -0/+31 | |
| 2018-02-26 | Fix Kingfisher regulator | Vladimir Barinov | 2 | -54/+0 | |
| The patch 0035-* breaks regulators on KF board. As a result the Multichannal audio was broken | |||||
| 2018-02-26 | LVDS: move from poc-supply to poc-gpios | Vladimir Barinov | 2 | -494/+163 | |
| Use gpiod instead of gpio regulator in LVDS drivers This is ruquired to remove patch: 0035-regulator-fixed-probe-after-i2c.patch The above patch breaks regulators support on Kingfisher board | |||||
| 2018-02-26 | LVDS: remove helper patches for vendor cameras | Vladimir Barinov | 4 | -1038/+0 | |
| Remove these helper patches since it is possible to adjust cameras feature in kernel command line now | |||||
| 2018-02-26 | LVDS: unify TI9X4 deserilalizers family, add V3MZF board | Vladimir Barinov | 7 | -1674/+1705 | |
| 1) unify TI9X4 deseializers (TI954, TI964) 2) add V3MZF board 3) shorten deserilziers name in Kconfig/Makefile 4) add camera sensor AR0220 | |||||
| 2018-02-01 | VB2: add MCP251X driver for can2 and can3 | Andrey Gusakov | 1 | -0/+1 | |
| 2018-02-01 | VB2: add rtc dts node | Andrey Gusakov | 1 | -6/+10 | |
| 2018-01-31 | H3 ws2.0: fix ssi349 name | Vladimir Barinov | 2 | -0/+29 | |
| This is tested on KF + H3 ws2.0 | |||||
| 2018-01-31 | V3M/H: fix IMP resources | Vladimir Barinov | 2 | -21/+53 | |
| Fix IMP sizes/names/sysc Add new IMP blocks | |||||
| 2018-01-28 | LVDS: add poc-delay dts field | Vladimir Barinov | 1 | -37/+71 | |
| 1) add poc-delay field that introduces extra delay after apply POC-supply power. Default value is 50ms 2) add stability fixes for AP0101-AR014x cameras: read OTP_ID runtime (do not use cached value at kernel boot time, since it may read unstable/incorrectly) | |||||
| 2018-01-28 | Use POC-supply in VB, VB2 based board | Vladimir Barinov | 1 | -214/+308 | |
| 1) replace gpio-hog power with POC-supply regulator on VideoBox and VideoBox2 boards 2) remove sensor-delay filed form dts if it is 0 and if it is replaced with POC-supply | |||||
| 2018-01-25 | V3H: Add GETHER | Vladimir Barinov | 3 | -96/+278 | |
| 1) Add GETHER in uboot/kernel 2) Condor board: setup as default interface | |||||
| 2018-01-24 | SPI slave: fix WARN message | Vladimir Barinov | 3 | -28/+1 | |
| This fixes warn message form spidev driver | |||||
| 2018-01-23 | [linux-renesas] add support MD and RAID devices into ulcb config |   Roman Meshkevich | 1 | -0/+3 | |
| 2018-01-23 | OV490-OV10640: add module params | Vladimir Barinov | 1 | -31/+35 | |
| 1) add dvp_order module parameter 2) add max_height, max_width params This will allow override default dts params using kernel command line: f.e.: " ov106xx.dvp_order=2" or " ov106xx.max_width=1280 ov106xx.max_height=966 max9286.gpio_resetb=4 max9286.active_low_resetb=1 max9286.fsync_period=3200000" | |||||
| 2018-01-23 | MSIOF: add SPIDEV function | Vladimir Barinov | 11 | -6/+4348 | |
| 1) add spidev function on MSIOF 2) set MSOIF1 master and MSIOF slave on V3MSK VideoBoxMini | |||||
| 2018-01-22 | V3M/V3H: fix CMT0 timer offset | Vladimir Barinov | 2 | -4/+4 | |
| 2018-01-22 | Add V3H support and Condor board | Vladimir Barinov | 6 | -8/+7189 | |
| 1) add uboot R-Car V3H SoC (r87798) and V3H based Condor board 2) add kernel R-Car V3H SoC (r87798) and V3H based Condor board | |||||
| 2018-01-22 | Eagle: remove USB_PEAK from kernel config | Vladimir Barinov | 1 | -1/+0 | |
| Remove this since Eagle does not have USB | |||||
 |
index : meta-renesas-rcar-gen3 | |
| Grokmirror user |
| aboutsummaryrefslogtreecommitdiffstats |