| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In YP2.6, xserver-xorg was upgraded to 1.20.1.
This breaks xserver-xorg congigures:
| configure: error: Package requirements (libdrm >= 2.4.89) were not met:
| Requested 'libdrm >= 2.4.89' but version of libdrm is 2.4.85
However, Renesas BSP uses libdrm version is 2.4.85.
Therefore, let downgrade this version to use 1.19.6.
It also modifies machine configuration to use xserver-xorg 1.19.6
version.
Signed-off-by: Thuy Tran <thuy.tran.xh@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit enables U-Boot configuration to build all binaries
for Salvator-X and Salvator-XS boards.
Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com>
Signed-off-by: Thuy Tran <thuy.tran.xh@renesas.com>
Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates machine configurations for the following items:
- Upgraded u-boot to v2018.09.
- Added supporting Ebisu 4D 2GiB board.
- Enabled building multiple u-boot configurations for H3 Salvator-XS,
Ebisu and H3ULCB.
Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
The kernel-module-gles is now using sync command to ensure installed
files get written to disk.
This commit adds sync to HOSTTOOLS to make sure that command is
available when installing this module.
Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates device tree names for H3.
There are 3 device trees as below:
- renesas/r8a7795-salvator-xs.dtb: for R-Car H3 SiP
DDR 4GiB (1GiB x 4ch)
- renesas/r8a7795-salvator-xs-2x2g.dtb: for R-Car H3 SiP
DDR 4GiB (2GiB x 2ch)
- renesas/r8a7795-salvator-xs-4x2g.dtb: for R-Car H3 SiP
DDR 8GiB (4GiB x 2ch)
In Yv3.7.0, we will support R-Car H3 SiP DDR 8GiB by default.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
cpio.gz has a limitation about size. If rootfs size is larger than
2GB, do_image_cpio will fail. Therefore, this commit removes
cpio.gz in our implementation.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
mesa v17.1.1 only supports libdrm from 2.4.75 and later,
so we set PREFERRED_VERSION_libdrm in board config
to use libdrm v2.4.85 from poky to prevent configure error.
| checking for libdrm >= 2.4.75... no
| checking for glproto >= 1.4.14... yes
| configure: error: Direct rendering requires libdrm >= 2.4.75
| NOTE: The following config.log files may provide further information.
| NOTE: /build/tmp/work/aarch64-poky-linux/mesa/2_17.1.1-r0/build/config.log
| ERROR: configure failed
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates recipes to support for R-Car M3N board
(SoC: R8A77965).
The support for M3N by following items:
- machine: Add support for M3N with tuning file for cortex-a57.
- linux-renesas: Upgrade Linux BSP to v3.5.9.
- u-boot: Add support for R-Car M3N.
- IPL: Update SRCREV to follow the latest version.
- README: Add M3N information.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
Board configs should append to previously set IMAGE_FSTYPES
instead of overriding it.
Change-Id: If5101784f574a96185351e96b7c0cbd120fd90dc
Signed-off-by: Anton Gerasimov <anton@advancedtelematic.com>
Signed-off-by: Stephane Desneux <stephane.desneux@iot.bzh>
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
(cherry picked from commit b4c458d529bfad0bd85c282912d3a237c8a3ebfb)
|
|
This commit upgrades Linux BSP to v3.5.3
and adds device tree file for M3 Salvator-XS board to salvator-x.conf.
Linux BSP to v3.5.3 updates following items:
Kernel core
- Add workaround for PRR register of R-Car M3 WS1.1.
(Fix printing cpu info.)
- Add device tree file for Salvator-XS board with R-Car M3.
- Fix R-Car M3 Salvator-X device tree file for MIX function
of Audio driver.
Power Management
- Mark the OPP to be used during system suspend.
- Enable CPUIdle function.
- Apply new CPUIdle parameters.
Audio driver
- Confirm this driver can resume with Suspend to RAM during capture.
- Avoid SSI_MODEx settings for SSI8.
- Clear DE bit only in PDMACHCR when it stops.
- Tidyup Audio-DMAC channel for DVC.
- Enable PCM RATE until 192000.
- Fix the setting of saved_rate during the resume process.
Display driver
- Fix the problem that the flicker may occur during rendering
by the application.
- Add brs option check for VGA connector.
- Add routing set for digital RGB previously.
DMA Engine driver
- Fix release resources after interrupt process.
Ethernet driver
- Add phy-reset-gpios.
This driver can work after Suspend to RAM with Salvator-XS board.
- Fix GIS_PTMF bit clearing in ravb_ptp_interrupt.
I2C driver
- Revert and fix about unnecessary function related to Suspend to RAM.
MSIOF driver
- Fix SPI division value setting of R-Car M3
based on hardware specification.
- Allow interrupts during msiof slave mode transfer wait.
- Revert and fix about unnecessary function related to Suspend to RAM.
RWDT driver
- Fix timeout count calculation.
SCIF/HSCIF driver
- Fix panic when serial console and DMA are enabled.
- Revert about unnecessary function related to Suspend to RAM.
SD/MMC driver
- Wait for CBSY instead of SCLKDIVEN.
- Add re-tuning condition.
- Add internal DMAC reset at startup.
- Add the driver strength setting.
eMMC HS400 mode can work with R-Car M3 WS1.1 on Salvator-XS board.
Thermal driver
- Fix to support thermal for both M3 WS1.0 and WS1.1.
Video Capture driver
- Fix resuming procedure.
- Fix first field detection control.
- Fix 720x480p transfer rate.
- Fix video standard selection register setting.
Change-Id: I3b0d6237c9d0c56a9f2870f1fde89ea215f163cd
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
Renesas BSP v3.5.1 (kernel v4.9 stable)
[Environment]
poky: yocto-2.1.2 (cca8dd15c8096626052f6d8d25ff1e9a606104a3)
meta-openembedded: 55c8a76da5dc099a7bc3838495c672140cedb78e
meta-linaro: 2f51d38048599d9878f149d6d15539fb97603f8f
[Information]
- U-boot: Changed load address from H'49000000 to H'50000000
- XDG_RUNTIME_DIR has been changed from "/run/user/root" to "/run/user/0"
- Change location of include directory, which stores common user header
files, to $(INCSHARED)
- In BSP Only, core-image-weston is not supported even though
local-wayland.conf is provided.
- Please set Salvator-x SW7 Pin-1. In after Yocto BSP v2.12.0, it is
　necessary to enable BKUP_TRG signal for Suspend to RAM.
- The dtb filename was changed in R-Car H3. Only
"Image-r8a7795-es1-salvator-x.dtb" is supported in this version.
Please use "Image-r8a7795-es1-salvator-x.dtb" It supports R-Car H3
WS1.0 and WS1.1.
- Please update your local.conf and bblayers.conf corresponding to Yocto
v2.16.0 package. You can refer to meta-rcargen3/docs/sample/conf/ for
updated contents.
- You have to re-compile out-of-recipe software like user application by
v2.16.0 SDK toolchains.
- In some boards, the resuming from System Suspend to RAM may cause
unstable operation or failed to resume.
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
Thuy Tran
Duy Dang
Khang Nguyen
Khang Nguyen
Thuy Tran
Thao Nguyen
Anton Gerasimov
Thao Nguyen
Takamitsu Honda