| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
H3ULCB will support new board with chip WS2.0.
There will be 2 device trees for H3ULCB corresponding to 2 board types:
- r8a7795-es1-h3ulcb.dtb: for H3ULCB WS1.1
- r8a7795-h3ulcb.dtb: for H3ULCB WS2.0
Change-Id: Ic11ee3f3e734641b020e3332721babd465cce2ae
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit upgrades Linux BSP to v3.5.3
and adds device tree file for M3 Salvator-XS board to salvator-x.conf.
Linux BSP to v3.5.3 updates following items:
Kernel core
- Add workaround for PRR register of R-Car M3 WS1.1.
(Fix printing cpu info.)
- Add device tree file for Salvator-XS board with R-Car M3.
- Fix R-Car M3 Salvator-X device tree file for MIX function
of Audio driver.
Power Management
- Mark the OPP to be used during system suspend.
- Enable CPUIdle function.
- Apply new CPUIdle parameters.
Audio driver
- Confirm this driver can resume with Suspend to RAM during capture.
- Avoid SSI_MODEx settings for SSI8.
- Clear DE bit only in PDMACHCR when it stops.
- Tidyup Audio-DMAC channel for DVC.
- Enable PCM RATE until 192000.
- Fix the setting of saved_rate during the resume process.
Display driver
- Fix the problem that the flicker may occur during rendering
by the application.
- Add brs option check for VGA connector.
- Add routing set for digital RGB previously.
DMA Engine driver
- Fix release resources after interrupt process.
Ethernet driver
- Add phy-reset-gpios.
This driver can work after Suspend to RAM with Salvator-XS board.
- Fix GIS_PTMF bit clearing in ravb_ptp_interrupt.
I2C driver
- Revert and fix about unnecessary function related to Suspend to RAM.
MSIOF driver
- Fix SPI division value setting of R-Car M3
based on hardware specification.
- Allow interrupts during msiof slave mode transfer wait.
- Revert and fix about unnecessary function related to Suspend to RAM.
RWDT driver
- Fix timeout count calculation.
SCIF/HSCIF driver
- Fix panic when serial console and DMA are enabled.
- Revert about unnecessary function related to Suspend to RAM.
SD/MMC driver
- Wait for CBSY instead of SCLKDIVEN.
- Add re-tuning condition.
- Add internal DMAC reset at startup.
- Add the driver strength setting.
eMMC HS400 mode can work with R-Car M3 WS1.1 on Salvator-XS board.
Thermal driver
- Fix to support thermal for both M3 WS1.0 and WS1.1.
Video Capture driver
- Fix resuming procedure.
- Fix first field detection control.
- Fix 720x480p transfer rate.
- Fix video standard selection register setting.
Change-Id: I3b0d6237c9d0c56a9f2870f1fde89ea215f163cd
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit addes "ulcb" into MACHINEOVERRIDES.
"ulcb" contains h3ulcb and m3ulcb.
It will help the implementation in the future
become easier to maintain for ULCB group.
Change-Id: I3c5d66f1e36e85f07d96a74f566fc1ffd5a76ee6
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
Renesas BSP v3.5.1 (kernel v4.9 stable)
[Environment]
poky: yocto-2.1.2 (cca8dd15c8096626052f6d8d25ff1e9a606104a3)
meta-openembedded: 55c8a76da5dc099a7bc3838495c672140cedb78e
meta-linaro: 2f51d38048599d9878f149d6d15539fb97603f8f
[Information]
- U-boot: Changed load address from H'49000000 to H'50000000
- XDG_RUNTIME_DIR has been changed from "/run/user/root" to "/run/user/0"
- Change location of include directory, which stores common user header
files, to $(INCSHARED)
- In BSP Only, core-image-weston is not supported even though
local-wayland.conf is provided.
- Please set Salvator-x SW7 Pin-1. In after Yocto BSP v2.12.0, it is
　necessary to enable BKUP_TRG signal for Suspend to RAM.
- The dtb filename was changed in R-Car H3. Only
"Image-r8a7795-es1-salvator-x.dtb" is supported in this version.
Please use "Image-r8a7795-es1-salvator-x.dtb" It supports R-Car H3
WS1.0 and WS1.1.
- Please update your local.conf and bblayers.conf corresponding to Yocto
v2.16.0 package. You can refer to meta-rcargen3/docs/sample/conf/ for
updated contents.
- You have to re-compile out-of-recipe software like user application by
v2.16.0 SDK toolchains.
- In some boards, the resuming from System Suspend to RAM may cause
unstable operation or failed to resume.
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
Yusuke Goda
Thao Nguyen
Takamitsu Honda