summaryrefslogtreecommitdiffstats
path: root/meta-rcar-gen3/recipes-kernel/linux-libc-headers
AgeCommit message (Collapse)AuthorFilesLines
2017-06-21rcar-gen3: linux-renesas: Update BSP to v3.5.5Thao Nguyen1-2/+2
This commit updates Linux BSP from v3.5.3 to v3.5.5 for following items: Kernel core - Add ZG clock divider support. - Revert and fix about Suspend to RAM. - Add DEVFREQ support for GSX. - Add usb companion property in EHCI. - Add USB3.0 peripheral device node. - Use IPMMU(MMU mode) for IPMMU-VP and IPMMU-VC0/1 with R-Car H3 Ver.1.x, for IPMMU-VP0/1 and IPMMU-VC0/1 with R-Car H3 Ver.2.0, in IPMMUVC0 with R-Car M3. - Add override support for the actual number of MMU contexts. - Fix audio Mix support on DTSI. Power Management - Cleanup AVS driver. - Update voltage for VDD_DVFS and VDD. Audio driver - Resolve 16bit/24bit capture noise problem by enabling clock-frequency for both 4.1kHz/48kHz and fixing possible NULL pointer dereference. - Resolve playback problem of sampling rate 32kHz, 176.4kHz and 192kHz by enabling clock-frequency for both 44.1kHz/48kHz. - Resolve “can’t get dma channel” error at the time of unbind/bind by fixing up of_clk_add_provider() usage for multi clkout and calling the missing of_clk_del_provider() when removing. - Resolve 48kHz audio 1-20k sweep noise problem by enabling clock-frequency 44.1kHz/48kHz. - Merge rsnd_kctrl_new_m/s/e into rsnd_kctrl_new(). - Fix 24bit capture noise problem by not using PDTA bit for 24bit on SSI. - Request/Release DMA channel each time for avoiding error of getting dma channel. Display driver - Use dma_map_sg_attrs to skip synchronization of the CPU cache. - Add mode_fixup callback function. - Control clock of bridge during S2RAM and change to control clock via clock driver. - Fix reserved register setting for R-Car for H/W manual update. - Add null pointer check for brs option. - Revert "drm: bridge/dw-hdmi: Add HDP interrupt disable for suspend". - Fix hierarchy of driver structure for clk-5p49x. DMA Engine driver - Revert dma pause function because it was rejected by upstream. GPIO driver - Revert and fix about Suspend to RAM. - Add GP-1-28 port pin support for R-Car H3 Ver.2.0 because of H/W manual updating to Rev.0.54E. Modify just PFC and DT. SCIF/HSCIF driver - Resolve system freezing. SD/MMC driver - Add initial setting of interrupt mask register. - Fix command sequence at error detection. - Fix “Wait for CBSY instead of SCLKDIVEN”. - Fix processing when detecting SCC error and fix error handling when issuing CMD23. - Fix reset_hs400_mode. - Fix problem that SDIO interrupt may be missed. USB3.0 Function - Add Role-change support. - Add DMA support. - Add basic function support. USB2.0 Host driver - Fix mouse connection time (2 second or more) when resuming. USB3.0 Host driver - Support for R-Car Gen3 USB 3.0 PHY for SSC function. - Add R-Car Gen3 USB 2.0 clock selector PHY, support for R-Car Gen3 USB 3.0 PHY. Video Capture driver - Add 2 lane support with rcar-csi2.c. - Fix image alignment for setting pre clipping. - Fix wait time for software reset in rcar-csi2.c because of H/W manual updating to Rev.0.54E. - Fix PHY initialization in rcar-csi2.c because of H/W manual updating to Rev.0.54E. - Fix PHTW register setting in rcar-csi2.c because of H/W manual updating toRev.0.54E. - Fix wait procedure usleep_range from msleep in adv7482.c. - Fix channel get procedure. Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-04-19rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.5.3Thao Nguyen1-2/+2
This commit upgrades Linux BSP to v3.5.3 and adds device tree file for M3 Salvator-XS board to salvator-x.conf. Linux BSP to v3.5.3 updates following items: Kernel core - Add workaround for PRR register of R-Car M3 WS1.1. (Fix printing cpu info.) - Add device tree file for Salvator-XS board with R-Car M3. - Fix R-Car M3 Salvator-X device tree file for MIX function of Audio driver. Power Management - Mark the OPP to be used during system suspend. - Enable CPUIdle function. - Apply new CPUIdle parameters. Audio driver - Confirm this driver can resume with Suspend to RAM during capture. - Avoid SSI_MODEx settings for SSI8. - Clear DE bit only in PDMACHCR when it stops. - Tidyup Audio-DMAC channel for DVC. - Enable PCM RATE until 192000. - Fix the setting of saved_rate during the resume process. Display driver - Fix the problem that the flicker may occur during rendering by the application. - Add brs option check for VGA connector. - Add routing set for digital RGB previously. DMA Engine driver - Fix release resources after interrupt process. Ethernet driver - Add phy-reset-gpios. This driver can work after Suspend to RAM with Salvator-XS board. - Fix GIS_PTMF bit clearing in ravb_ptp_interrupt. I2C driver - Revert and fix about unnecessary function related to Suspend to RAM. MSIOF driver - Fix SPI division value setting of R-Car M3 based on hardware specification. - Allow interrupts during msiof slave mode transfer wait. - Revert and fix about unnecessary function related to Suspend to RAM. RWDT driver - Fix timeout count calculation. SCIF/HSCIF driver - Fix panic when serial console and DMA are enabled. - Revert about unnecessary function related to Suspend to RAM. SD/MMC driver - Wait for CBSY instead of SCLKDIVEN. - Add re-tuning condition. - Add internal DMAC reset at startup. - Add the driver strength setting. eMMC HS400 mode can work with R-Car M3 WS1.1 on Salvator-XS board. Thermal driver - Fix to support thermal for both M3 WS1.0 and WS1.1. Video Capture driver - Fix resuming procedure. - Fix first field detection control. - Fix 720x480p transfer rate. - Fix video standard selection register setting. Change-Id: I3b0d6237c9d0c56a9f2870f1fde89ea215f163cd Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-03-23rcar-gen3: linux-renesas: Update BSP to v3.5.2 and change coding styleThao Nguyen1-2/+2
This commit updates version of Linux BSP v3.5.1 -> v3.5.2 to fix following issues: [v3.5.2] - Display driver [H/W Restriction No.54] + In R-Car H3 WS1.x, distortion appears on the screen, when IPMMU is enabled. But this problem is fixed with R-Car H3 WS2.0. - Video Capture driver + Fix remove procedure. - Add board Salvator-XS and H3 WS 2.0 support. It also modifies the linux-renesas_4.9.bb to change the way common files are included. There is no difference in kernel config files of Salvator-X, H3ULCB and M3ULCB so far. Hence, we only need to install one file to avoid confusion. Change-Id: I145e0a7696f97fe1841a8a213c51c5685ada0290 Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-01-27First commit.Renesas-Yocto-v2.16.0Takamitsu Honda1-0/+10
Renesas BSP v3.5.1 (kernel v4.9 stable) [Environment] poky: yocto-2.1.2 (cca8dd15c8096626052f6d8d25ff1e9a606104a3) meta-openembedded: 55c8a76da5dc099a7bc3838495c672140cedb78e meta-linaro: 2f51d38048599d9878f149d6d15539fb97603f8f [Information] - U-boot: Changed load address from H'49000000 to H'50000000 - XDG_RUNTIME_DIR has been changed from "/run/user/root" to "/run/user/0" - Change location of include directory, which stores common user header files, to $(INCSHARED) - In BSP Only, core-image-weston is not supported even though local-wayland.conf is provided. - Please set Salvator-x SW7 Pin-1. In after Yocto BSP v2.12.0, it is  necessary to enable BKUP_TRG signal for Suspend to RAM. - The dtb filename was changed in R-Car H3. Only "Image-r8a7795-es1-salvator-x.dtb" is supported in this version. Please use "Image-r8a7795-es1-salvator-x.dtb" It supports R-Car H3 WS1.0 and WS1.1. - Please update your local.conf and bblayers.conf corresponding to Yocto v2.16.0 package. You can refer to meta-rcargen3/docs/sample/conf/ for updated contents. - You have to re-compile out-of-recipe software like user application by v2.16.0 SDK toolchains. - In some boards, the resuming from System Suspend to RAM may cause unstable operation or failed to resume. Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>