meta-renesas-rcar-gen3 -

Age	Commit message (Collapse)	Author	Files	Lines
2019-07-15	rcar-gen3: linux-renesas: Update Linux BSP to v3.9.6	Duy Dang	1	-10/+29
	This commit updates Linux BSP version to v3.9.6 for the following changes: [Audio driver] - Fixup 6ch settings to 8ch. The rsnd need to use 8ch clock settings for 6ch for TDM. - Avoid a potential deadlock. [DMA Engine driver] - With cyclic DMA residue 0 is valid. [IPMMU driver] - Remove cache snoop transaction for page table walk request. [SD/MMC driver] - Fix SCC error handling to avoid false positive CRC error. [Thermal driver] - Fix interrupt type. - Disable interrupt in .remove function. - Fix initial value of IRQCTL register. [USB2.0 Host driver] - Correct VBUS behavior at over-current. [Kernel] - [H/W Restriction No.123] The eMMC of R-Car M3 Ver.3.0 is restricted up to HS200 for H/W restriction by device tree. Change-Id: I36706b190a921ee8ec086f6c74a7fa986a0a1980 Signed-off-by: Duy Dang <duy.dang.yw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-12-19	rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.9.2	Duy Dang	1	-0/+82
	This commit upgrades Linux BSP to v3.9.2 for the following changes: [Kernel] - Add support for RCKSEL clock selection. - Fix pin functions of R-Car E3 according to H/W UM Rev1.00 errata. - Fix warning of the make W=1 C=2. - Identify R-Car M3 Ver.1.3. - Add the big.LITTLE CAS scheduler fix patches. - Fix MOD_SEL bit numbering for R-Car E3. [Power Management] - Fixup power-domains of 3DGE for R-Car E3 Ver.1.0 and add device tree file for R-Car E3 Ver.1.0. [Audio Driver] - Fixup clock start checker. - Resolve the problem that the noise is generated during long playback with R-Car E3 Ebisu-4D board by kernel rebasing. [Display Driver] - Add function of suspend and resume to adv7511_drv.c and add hot plug event function at resume in rcar_du_drv.c. - Add depends on DRM_RCAR_DU to config DRM_RCAR_LVDS. - Revert "drm: rcar-du: Fix legacy DT to create LVDS encoder nodes". - Add clock function for LVDS PLL. [Ethernet Driver] - Decrease TxFIFO depth of Q3 and Q2 to one. - Fix not to call phy_resume() if PHY is not attached and add toggling phy reset if PHY is not attached. - Revert "ravb: RX checksum offload" for communicating of Q-Tag VLAN frame correctly. - Resolved the problem that the S2RAM resume failed on R-Car E3 Ebisu-4D by kernel rebasing. - Avoid unsupported internal delay mode for R-Car E3 and limit to 100Mbps. [I2C Driver] - Check bus state before reinitializing. [IPMMU Driver] - Fix crash on early domain free. - Revert "arm64: defconfig: Enable QCOM_IOMMU" for suspending with LTSI kernel. - Correct whitelist devices assignment. [PCIe Driver] - Avoid PCI device removing/rescanning through sysfs triggers a deadlock. [PWM Driver] - Avoid deadlock warning when removing PWM device. [SD/MMC Driver] - Fix card initialization failure in high speed mode. - Add adjust HS400 offset by manual calibration mode and adjust HS400 offset by manual calibration mode for R-Car M3 Ver.1.3. [USB2.0 Function] - Add reset_control. - Backport upstream patches to support OTG mode for R-Car E3. - Make DMAC system sleep callbacks explicit. - Add Super-Speed (b-device) support. [Video Capture driver] - Review adv748x driver for R-Car E3 Ebisu board and add option for changing SD output route to TXA. - Revert "rcar-vin: rcar-csi2: Add blank margin when caluculating bit rate" and fix pixel rate values. - Add CPG reset and release when using digital pin. [RWDT Driver] - Don't keep timer value during suspend/resume. - Don't set divider while watchdog is running. This also updates ADSP driver patches to adapt to the new Linux version. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xv@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>