summaryrefslogtreecommitdiffstats
path: root/meta-rcar-gen3/recipes-kernel/linux/linux-renesas
AgeCommit message (Collapse)AuthorFilesLines
2018-12-19rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.9.2Duy Dang14-1636/+1739
This commit upgrades Linux BSP to v3.9.2 for the following changes: [Kernel] - Add support for RCKSEL clock selection. - Fix pin functions of R-Car E3 according to H/W UM Rev1.00 errata. - Fix warning of the make W=1 C=2. - Identify R-Car M3 Ver.1.3. - Add the big.LITTLE CAS scheduler fix patches. - Fix MOD_SEL bit numbering for R-Car E3. [Power Management] - Fixup power-domains of 3DGE for R-Car E3 Ver.1.0 and add device tree file for R-Car E3 Ver.1.0. [Audio Driver] - Fixup clock start checker. - Resolve the problem that the noise is generated during long playback with R-Car E3 Ebisu-4D board by kernel rebasing. [Display Driver] - Add function of suspend and resume to adv7511_drv.c and add hot plug event function at resume in rcar_du_drv.c. - Add depends on DRM_RCAR_DU to config DRM_RCAR_LVDS. - Revert "drm: rcar-du: Fix legacy DT to create LVDS encoder nodes". - Add clock function for LVDS PLL. [Ethernet Driver] - Decrease TxFIFO depth of Q3 and Q2 to one. - Fix not to call phy_resume() if PHY is not attached and add toggling phy reset if PHY is not attached. - Revert "ravb: RX checksum offload" for communicating of Q-Tag VLAN frame correctly. - Resolved the problem that the S2RAM resume failed on R-Car E3 Ebisu-4D by kernel rebasing. - Avoid unsupported internal delay mode for R-Car E3 and limit to 100Mbps. [I2C Driver] - Check bus state before reinitializing. [IPMMU Driver] - Fix crash on early domain free. - Revert "arm64: defconfig: Enable QCOM_IOMMU" for suspending with LTSI kernel. - Correct whitelist devices assignment. [PCIe Driver] - Avoid PCI device removing/rescanning through sysfs triggers a deadlock. [PWM Driver] - Avoid deadlock warning when removing PWM device. [SD/MMC Driver] - Fix card initialization failure in high speed mode. - Add adjust HS400 offset by manual calibration mode and adjust HS400 offset by manual calibration mode for R-Car M3 Ver.1.3. [USB2.0 Function] - Add reset_control. - Backport upstream patches to support OTG mode for R-Car E3. - Make DMAC system sleep callbacks explicit. - Add Super-Speed (b-device) support. [Video Capture driver] - Review adv748x driver for R-Car E3 Ebisu board and add option for changing SD output route to TXA. - Revert "rcar-vin: rcar-csi2: Add blank margin when caluculating bit rate" and fix pixel rate values. - Add CPG reset and release when using digital pin. [RWDT Driver] - Don't keep timer value during suspend/resume. - Don't set divider while watchdog is running. This also updates ADSP driver patches to adapt to the new Linux version. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xv@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: linux-renesas: Add support ADSP ALSA driverKhang Nguyen5-0/+7482
This commit modifies recipes to support building ADSP ALSA driver when enabling adsp distro feature. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: linux-renesas: Update device tree to support ADSP ALSA driverKhang Nguyen6-0/+240
This commit applies device tree rollback patches to support ADSP ALSA driver. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.8.0Khang Nguyen1-48/+89
This commit upgrades Linux BSP to v3.8.0 for the following updates: [Kernel] - Fix CPG definitions of R-Car H3/M3N/E3 for H/W manual Rev.1.00. - PFC definitions of R-Car H3/M3N/E3 for H/W manual Rev.1.00. - Fix R-Car H3/M3N/E3 module clock system mistake. [Audio driver] - Fixup not to call clk_get/set under non-atomic. - Fixup SSI clock during suspend/resume modes. [Display driver] - Don't use TV sync mode when not supported by the hardware. - Add clock driver registration for LVDS PLL. [SATA driver] - Fix really mask all interrupts on Gen2 and later. [SD/MMC driver] - Add adjust HS400 offset by manual calibration mode. - Change HW adjustment register according to speed mode. [Video Capture driver] - Fix PHTW register procedure and VnCSI_IFMD register access for R8A77990. - Fix scaling judgement condition of #181156 patch. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-29Revert "rcar-gen3: linux-renesas: WORKAROUND for mini SD card issue on M3ULCB"Khang Nguyen1-112/+0
The Kernel source has been updated. This reverts commit 8b090e008ef2c4cb9a97c20426f1ac03f9f15555. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-19Revert "rcar-gen3: linux-renesas: Enable DEVFREQ configuration"Khang Nguyen1-10/+0
The Kernel Source has been updated. This reverts commit a1e844b0849b1c47f37f6ae6095b17bff5f79539 which is no longer needed. Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-10-19rcar-gen3: linux-renesas: Upgrade Linux BSP to 3.7.3Khang Nguyen1-1/+18
This commit upgrades Linux BSP to 3.7.3 for the following updates: [Kernel] - Enable DEVFREQ configuration. [Audio driver] - Fix the noise problem when repeating start and stop of playback during capture. [Display driver] - Fix about reserved bits, unused registers and offset address related to HDMI registers for R-Car. - Add re-write of vsync pulse width. - Add dot clock valid check. - Revert "v4l: vsp1: Add max RPF number check". - Fix read past end of lvds[] array and fix div-by-0 when propagating pixelrate. - Fix bridge null check. - Track dma-buf fences. - Fix definitions according to H/W UM Rev1.00. - Allow importing non-contiguous dma-buf with VSP and set the DMA coherent mask for the DU device - Fix to refer to member after Null check in vsp1_pipe.c. [DMA Engine driver] - Add dma_pause operation. - Don’t use DMAC error interrupt. - Avoid to writing CHCR.TE to 1 if TCR is set to 0. [I2C driver] - Fix dma_direction variable clear. - Cleanup DMA for all kinds of failure. [MSIOF driver] - Fix handling of writing value of SISTR register. - Change wait time of reset completion [PCIe driver] - Handle returned value of rcar_pcie_wait_for_dl for warning QAC with MISRA-C 2012. [SD/MMC driver] - Backport upstream patch “mmc: core: properly init drv_type”. - Fix the definition of RST_RESERVED_BITS. - [H/W Restriction No.109] R-Car M3 Ver.1.2 or earlier does not support eMMC HS400 mode. It supports up to HS200 mode. [USB2.0 Host driver] - Add wait for IDDIG. [Video Capture driver] - Cleanup notifier in error path. - Add streaming count check when streming off. - Fix definitions according to H/W UM Rev1.00. - Fix setting order of UDS disable. Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-06-18rcar-gen3: linux-renesas: WORKAROUND for mini SD card issue on M3ULCBKhang Nguyen1-0/+112
This commit adds a WORKAROUND patch for the issue that mini SD partition information cannot be read correctly. Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-06-18rcar-gen3: linux-renesas: Enable DEVFREQ configurationTakeshi Kihara1-0/+10
This commit enables DEVFREQ configuration. Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-06-18rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.7.0Khang Nguyen7-375/+8
This commit upgrades Linux BSP to v3.7.0 for following updates: [Kernel] - Change Linux version to v4.14.35 from v4.14. - Add support ZG clock divider for R8A77990 (R-Car E3). - Remove patch for Identifing R-Car M3 Ver.1.2 or later. [Power Management] - Fix "Using plain integer as NULL pointer" in rcar_ems_ctrl.c. - Add AVS support for gsx_opp_table. - Update SYSC power ON/OFF flow. [Display driver] - Fix procedure for extal and dotclkin selection for R-Car E3. - Add shutdown callback function in platform_driver". - Fix state flag in case of dual link mode for R-Car E3. [Ethernet driver] - Move reset-gpios property to EthernetAVB node for R-Car E3 Ebisu board. [I2C driver] - Fix handling of the RESTART phase and STOP phase. [MSIOF driver] - Add 2 clock delay by R-Car H3 Ver.3.0 only specification. [SD/MMC driver] - Fix eMMC HS400 mode setting. - Delete wait in tuning process. [USB2.0 Function] - Avoid wrong list handling in printer_write(). [USB2.0 Host driver] - Avoid the problem of Suspend to RAM in case of connecting USB mouse by removing following patches: <commit ID:cad25bf1> phy: rcar-gen3-usb2: Add the interrupt disabled in suspend <commit ID:318b535> phy: rcar-gen3-usb2: Support System Suspend To RAM [Video Capture driver] - Fix IFMD table information for R8A77990 (R-Car E3). Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-04-21rcar-gen3: linux-renesas: Apply the power control patches for H3 Ver.3.0Khang Nguyen6-0/+352
This commit applies the power control patches in R-Car H3 Ver.3.0. Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-04-21rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.6.2Khang Nguyen1-1/+2
This commit upgrades Linux BSP to v3.6.2 for following updates: [Kernel] - "WARNING: possible circular locking dependency detected" occurs with repeating reboot. However, it was false positive, and it was confirmed that there was no problem. - Identify R-Car M3 Ver.1.2 or later. - Remove lossy descompress area from MMNGR node and reduce reserved area for R-Car E3 Ebisu board. [Power Management] - Improve power domains always on implementation. - Fix interrupts are not raised issue on R-Car E3. - Update CAS source. [Display driver] - Add overlay layer size check. - Fix possible crtcs for plane when using VSPDL. [IPMMU driver] - Add workaround for disabling uTLBs. [MSIOF driver] Add MSIOF module clock changing processing for R-Car Series, 3rd Generation. [PCIe driver] - Fix memory leak in of_pci_get_host_bridge_resources. [Thermal driver] - Use DIV_ROUND_CLOSEST correctly as its description. [USB3.0 Host driver] - Cannot Suspend to RAM when enabling USB3.0. - Confirm recognition of USB3.0 memory through HUB for setting /etc/udev/rules.d/99-usb.rules. [Video Capture driver] - Allocate a scratch buffer at stream start. Then use scratch buffer and always run in continuous mode. - Fix PHTW register flow below 250 mbps. - Fix clock control flow so that the warning message “MSTP status timeout” is not displayed and when UDS (scaling) is executed at VIN0, a black screen does not come out. - Fix streaming procedure when resuming. [Audio driver] - Playback or capture doesn’t resume after Suspend to RAM. [USB2.0 Function] - Kernel error occurs with rmmod of g_printer. - The dd command error occurs with g_mass_storage. [USB2.0 Host driver] - When connecting USB mouse, “Bad mode in Error handler” may occur with Suspend to RAM. Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-03-22rcar-gen3: linux-renesas: Enable RPMSG_VIRTIO config depend on ICCOMKhang Nguyen2-0/+28
This commit modifies recipe to enable RPMSG_VIRTIO config depend on ICCOM distro feature. Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-03-22rcar-gen3: linux-renesas: Add support E3 and upgrade Linux BSP to v3.6.1Khang Nguyen1-3/+6
This commit adds support E3 and upgrades Linux BSP to v3.6.1 for the following updates: [Kernel] - Add R-Car E3 support. - Fix Gfx clock. [Power Management] - Register clock for all cpu nodes for R-Car H3 to device tree. - Improve to build only when enabling RCAR_POWER_AVS. - Update IPA for CA53, need tune "contribution" parameter. - Fix section mismatch build warnings. - Fix double source of drivers/soc/renesas/Kconfig. [Display driver] - Fix continuous mode for dual pipelines. - Fix DISP interrupt enable order, DPPR register set order and LVDS startup sequence. - Fix LVDS startup on R-Car Series, 3rd Generation. - Fix LVDS stop sequence. [DMA Engine driver] - Fix max_chunk_size for R-Car Series, 3rd Generation. - Check the done lists in rcar_dmac_chan_get_residue(). [I2C driver] - Fix the problem that the strange data transfers with DMA transmit. [IPMMU driver] - Fix sequence issue. [SD/MMC driver] - Fix handling of SET_BLOCK_COUNT for RPMB. [USB3.0 Function] - Fix oops in renesas_usb3_remove(). - Don't print a warning when setting link state for disabled ports. [Video Capture driver] - Fix transfer rate and phy register value. Add CPG reset release procedure. - Add bytes per line when opening device. - Fix power management procedure when resuming. - Add MSTP status check after CPG reset. - Fix division procedure for __udivdi3 error. Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-03-22Revert "rcar-gen3: linux-renesas: Fix M3ULCB hangs up when playing video"Khang Nguyen1-58/+0
Linux BSP v3.6.1 has been updated. This reverts commit f8e4fb869abdfac3211b5f933202644901eeac7a. Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-01-30rcar-gen3: linux-renesas: Fix M3ULCB hangs up when playing videoThuy Tran1-0/+58
The M3ULCB ES1.0 revision can not use CPUIdle for CA53 cores. This commit modifies recipes to apply a patch that disables CPUIdle support for CA53. Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-01-30rcar-gen3: linux-renesas: Update to enable USB 3.0Thuy Tran1-0/+4
This commit modifies recipe to install USB 3.0 firmware to kernel source and to enable USB 3.0 in kernel image. Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com> Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-01-30rcar-gen3: linux-renesas: Update to support CAS featureThuy Tran1-0/+1
This commit adds SCHED_DEBUG config fragment to support CAS. Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2018-01-30rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.6.0Thuy Tran25-1585/+930
This commit upgrades Linux BSP to v3.6.0 for supporting Kernel v4.14 stable and updating following items: [Kernel] - Add support for WDIOF_CARDRESET. [Power Management] - Add missing iounmap to rcar_avs.c. - Add big.LITTLE CAS support. - Add CA53 CPUIdle support. - Add CA53 EMS support. - Add CA53 CPUFreq support. [Audio driver] - Confirm rmmod command operation of snd-soc-rcar. - Skip disabled-SSI nodes. - Care ssi_parent_mod and remove NULL check from rsnd_mod_name()/rsnd_mod_id(). - Revert IOMMU support so far. - Don't use runtime->sample_bits. - More clear rsnd_get_dalign() for DALIGN. - Clear SSI_MODE for non TDM Extended modes. [Display driver] - Confirm the Fence function. - Add support for colorkey alpha blending. - Disable vsp1 interrupt when startup. [DMA Engine driver] - Fix array-bounds warning refer chcr_ts[]. [PWM driver] - Enable PWM2 in device tree. [USB2.0 Function] - Fix the problem that the interrupt becomes long time when disconnecting the USB cable. [Video Capture driver] - Add V4L2_FIELD_SEQ_TB/BT function support. - Add ARGB8888 caputre format support and overflow debug message option. - Fix cropping procedure. [RWDT driver] - Add support for WDIOF_CARDRESET. Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-11-24rcar-gen3: linux-renesas: Update SRC_URI to support ICCOM moduleThuy Tran24-0/+1315
This commit modifies Linux BSP recipes to add more patches to support ICCOM module. Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-11-24rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.5.9Thuy Tran1-0/+2
Linux BSP has been upgraded for supporting R-Car M3N Ver.1.0 and updating following items: [Kernel] - Add R-Car M3N Ver.1.0 support. - Fix MSIOF3 and VI5_DATA13 pinmux settings. [Audio driver] - Don't check SSISR::DIRQ when Capture. - Call dummy write for PW_MGMT1/3 with AK4613 when Playback. - TDM 6ch needs 8ch clock for hw refine. - Fix pcm-creation regression. [Display driver] - Fix race condition when disabling planes at CRTC stop and add reference counting to drm_atomic_state. - Fix register parameters passed to HDMI. - Unconditionally call prepare_fb and remove drm_atomic_helper_framebuffer_changed. [DMA Engine driver] - Fixup descriptor pointer for descriptor mode and use TCRB instead of TCR for residue. [Ethernet driver] - Fix condition of phy reset. [I2C driver] - Fix I2C DMA reception by adding reset. - Fix I2C DMA transmission by setting sequence. - Fix DMA Callback processing of I2C dma mode. - Fix handling of the STOP phase. [MFISLock driver] - Revert and add support for R-Car Gen3 Hardware Spinlock again. [SD/MMC driver] - Add identification of TAP and clock settings of HS400. - Fix HS400 mode selection process. - Fix SCC error check condition. [USB2.0 Function] - Avoid spinlock recursion. [USB3.0 Function] - Fix for no-data control transfer and fix Pn_RAMMAP.Pn_MPKT value. - Fix return value of usb3_write_pipe(). - The maximum PIPEs change from 30 to 5 except PIPE0 and EP0 by H/W specification’s change. H/W specification is fixed because it has description mistakes. [Video Capture driver] - Remove VnMC setting when setting VnCSI_IFMD. - Fix PHTW register parameter for mbps. Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-06-21rcar-gen3: linux-renesas: Update BSP to v3.5.5Thao Nguyen1-2/+22
This commit updates Linux BSP from v3.5.3 to v3.5.5 for following items: Kernel core - Add ZG clock divider support. - Revert and fix about Suspend to RAM. - Add DEVFREQ support for GSX. - Add usb companion property in EHCI. - Add USB3.0 peripheral device node. - Use IPMMU(MMU mode) for IPMMU-VP and IPMMU-VC0/1 with R-Car H3 Ver.1.x, for IPMMU-VP0/1 and IPMMU-VC0/1 with R-Car H3 Ver.2.0, in IPMMUVC0 with R-Car M3. - Add override support for the actual number of MMU contexts. - Fix audio Mix support on DTSI. Power Management - Cleanup AVS driver. - Update voltage for VDD_DVFS and VDD. Audio driver - Resolve 16bit/24bit capture noise problem by enabling clock-frequency for both 4.1kHz/48kHz and fixing possible NULL pointer dereference. - Resolve playback problem of sampling rate 32kHz, 176.4kHz and 192kHz by enabling clock-frequency for both 44.1kHz/48kHz. - Resolve “can’t get dma channel” error at the time of unbind/bind by fixing up of_clk_add_provider() usage for multi clkout and calling the missing of_clk_del_provider() when removing. - Resolve 48kHz audio 1-20k sweep noise problem by enabling clock-frequency 44.1kHz/48kHz. - Merge rsnd_kctrl_new_m/s/e into rsnd_kctrl_new(). - Fix 24bit capture noise problem by not using PDTA bit for 24bit on SSI. - Request/Release DMA channel each time for avoiding error of getting dma channel. Display driver - Use dma_map_sg_attrs to skip synchronization of the CPU cache. - Add mode_fixup callback function. - Control clock of bridge during S2RAM and change to control clock via clock driver. - Fix reserved register setting for R-Car for H/W manual update. - Add null pointer check for brs option. - Revert "drm: bridge/dw-hdmi: Add HDP interrupt disable for suspend". - Fix hierarchy of driver structure for clk-5p49x. DMA Engine driver - Revert dma pause function because it was rejected by upstream. GPIO driver - Revert and fix about Suspend to RAM. - Add GP-1-28 port pin support for R-Car H3 Ver.2.0 because of H/W manual updating to Rev.0.54E. Modify just PFC and DT. SCIF/HSCIF driver - Resolve system freezing. SD/MMC driver - Add initial setting of interrupt mask register. - Fix command sequence at error detection. - Fix “Wait for CBSY instead of SCLKDIVEN”. - Fix processing when detecting SCC error and fix error handling when issuing CMD23. - Fix reset_hs400_mode. - Fix problem that SDIO interrupt may be missed. USB3.0 Function - Add Role-change support. - Add DMA support. - Add basic function support. USB2.0 Host driver - Fix mouse connection time (2 second or more) when resuming. USB3.0 Host driver - Support for R-Car Gen3 USB 3.0 PHY for SSC function. - Add R-Car Gen3 USB 2.0 clock selector PHY, support for R-Car Gen3 USB 3.0 PHY. Video Capture driver - Add 2 lane support with rcar-csi2.c. - Fix image alignment for setting pre clipping. - Fix wait time for software reset in rcar-csi2.c because of H/W manual updating to Rev.0.54E. - Fix PHY initialization in rcar-csi2.c because of H/W manual updating to Rev.0.54E. - Fix PHTW register setting in rcar-csi2.c because of H/W manual updating toRev.0.54E. - Fix wait procedure usleep_range from msleep in adv7482.c. - Fix channel get procedure. Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-03-23rcar-gen3: linux-renesas: Update BSP to v3.5.2 and change coding styleThao Nguyen9-11529/+1
This commit updates version of Linux BSP v3.5.1 -> v3.5.2 to fix following issues: [v3.5.2] - Display driver [H/W Restriction No.54] + In R-Car H3 WS1.x, distortion appears on the screen, when IPMMU is enabled. But this problem is fixed with R-Car H3 WS2.0. - Video Capture driver + Fix remove procedure. - Add board Salvator-XS and H3 WS 2.0 support. It also modifies the linux-renesas_4.9.bb to change the way common files are included. There is no difference in kernel config files of Salvator-X, H3ULCB and M3ULCB so far. Hence, we only need to install one file to avoid confusion. Change-Id: I145e0a7696f97fe1841a8a213c51c5685ada0290 Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-01-27First commit.Renesas-Yocto-v2.16.0Takamitsu Honda9-0/+17292
Renesas BSP v3.5.1 (kernel v4.9 stable) [Environment] poky: yocto-2.1.2 (cca8dd15c8096626052f6d8d25ff1e9a606104a3) meta-openembedded: 55c8a76da5dc099a7bc3838495c672140cedb78e meta-linaro: 2f51d38048599d9878f149d6d15539fb97603f8f [Information] - U-boot: Changed load address from H'49000000 to H'50000000 - XDG_RUNTIME_DIR has been changed from "/run/user/root" to "/run/user/0" - Change location of include directory, which stores common user header files, to $(INCSHARED) - In BSP Only, core-image-weston is not supported even though local-wayland.conf is provided. - Please set Salvator-x SW7 Pin-1. In after Yocto BSP v2.12.0, it is  necessary to enable BKUP_TRG signal for Suspend to RAM. - The dtb filename was changed in R-Car H3. Only "Image-r8a7795-es1-salvator-x.dtb" is supported in this version. Please use "Image-r8a7795-es1-salvator-x.dtb" It supports R-Car H3 WS1.0 and WS1.1. - Please update your local.conf and bblayers.conf corresponding to Yocto v2.16.0 package. You can refer to meta-rcargen3/docs/sample/conf/ for updated contents. - You have to re-compile out-of-recipe software like user application by v2.16.0 SDK toolchains. - In some boards, the resuming from System Suspend to RAM may cause unstable operation or failed to resume. Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>