| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The Kernel Source has been updated.
This reverts commit a1e844b0849b1c47f37f6ae6095b17bff5f79539 which is no
longer needed.
Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit upgrades Linux BSP to 3.7.3 for the following updates:
[Kernel]
- Enable DEVFREQ configuration.
[Audio driver]
- Fix the noise problem when repeating start and stop of playback
during capture.
[Display driver]
- Fix about reserved bits, unused registers and offset address related
to HDMI registers for R-Car.
- Add re-write of vsync pulse width.
- Add dot clock valid check.
- Revert "v4l: vsp1: Add max RPF number check".
- Fix read past end of lvds[] array and fix div-by-0 when propagating
pixelrate.
- Fix bridge null check.
- Track dma-buf fences.
- Fix definitions according to H/W UM Rev1.00.
- Allow importing non-contiguous dma-buf with VSP and set the DMA
coherent mask for the DU device
- Fix to refer to member after Null check in vsp1_pipe.c.
[DMA Engine driver]
- Add dma_pause operation.
- Don’t use DMAC error interrupt.
- Avoid to writing CHCR.TE to 1 if TCR is set to 0.
[I2C driver]
- Fix dma_direction variable clear.
- Cleanup DMA for all kinds of failure.
[MSIOF driver]
- Fix handling of writing value of SISTR register.
- Change wait time of reset completion
[PCIe driver]
- Handle returned value of rcar_pcie_wait_for_dl for warning QAC with
MISRA-C 2012.
[SD/MMC driver]
- Backport upstream patch “mmc: core: properly init drv_type”.
- Fix the definition of RST_RESERVED_BITS.
- [H/W Restriction No.109] R-Car M3 Ver.1.2 or earlier does not support
eMMC HS400 mode. It supports up to HS200 mode.
[USB2.0 Host driver]
- Add wait for IDDIG.
[Video Capture driver]
- Cleanup notifier in error path.
- Add streaming count check when streming off.
- Fix definitions according to H/W UM Rev1.00.
- Fix setting order of UDS disable.
Signed-off-by: Duy Dang <duy.dang.yw@rvc.renesas.com>
Signed-off-by: Khang Nguyen <khang.nguyen.xw@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit adds a WORKAROUND patch for the issue that mini SD partition
information cannot be read correctly.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit enables DEVFREQ configuration.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit upgrades Linux BSP to v3.7.0 for following updates:
[Kernel]
- Change Linux version to v4.14.35 from v4.14.
- Add support ZG clock divider for R8A77990 (R-Car E3).
- Remove patch for Identifing R-Car M3 Ver.1.2 or later.
[Power Management]
- Fix "Using plain integer as NULL pointer" in rcar_ems_ctrl.c.
- Add AVS support for gsx_opp_table.
- Update SYSC power ON/OFF flow.
[Display driver]
- Fix procedure for extal and dotclkin selection for R-Car E3.
- Add shutdown callback function in platform_driver".
- Fix state flag in case of dual link mode for R-Car E3.
[Ethernet driver]
- Move reset-gpios property to EthernetAVB node for R-Car E3 Ebisu
board.
[I2C driver]
- Fix handling of the RESTART phase and STOP phase.
[MSIOF driver]
- Add 2 clock delay by R-Car H3 Ver.3.0 only specification.
[SD/MMC driver]
- Fix eMMC HS400 mode setting.
- Delete wait in tuning process.
[USB2.0 Function]
- Avoid wrong list handling in printer_write().
[USB2.0 Host driver]
- Avoid the problem of Suspend to RAM in case of connecting USB mouse by
removing following patches:
<commit ID:cad25bf1> phy: rcar-gen3-usb2: Add the interrupt disabled
in suspend
<commit ID:318b535> phy: rcar-gen3-usb2: Support System Suspend To RAM
[Video Capture driver]
- Fix IFMD table information for R8A77990 (R-Car E3).
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit applies the power control patches in R-Car H3 Ver.3.0.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit upgrades Linux BSP to v3.6.2 for following updates:
[Kernel]
- "WARNING: possible circular locking dependency detected" occurs with
repeating reboot. However, it was false positive, and it was confirmed
that there was no problem.
- Identify R-Car M3 Ver.1.2 or later.
- Remove lossy descompress area from MMNGR node and reduce reserved area
for R-Car E3 Ebisu board.
[Power Management]
- Improve power domains always on implementation.
- Fix interrupts are not raised issue on R-Car E3.
- Update CAS source.
[Display driver]
- Add overlay layer size check.
- Fix possible crtcs for plane when using VSPDL.
[IPMMU driver]
- Add workaround for disabling uTLBs.
[MSIOF driver]
Add MSIOF module clock changing processing for R-Car Series,
3rd Generation.
[PCIe driver]
- Fix memory leak in of_pci_get_host_bridge_resources.
[Thermal driver]
- Use DIV_ROUND_CLOSEST correctly as its description.
[USB3.0 Host driver]
- Cannot Suspend to RAM when enabling USB3.0.
- Confirm recognition of USB3.0 memory through HUB for setting
/etc/udev/rules.d/99-usb.rules.
[Video Capture driver]
- Allocate a scratch buffer at stream start. Then use scratch buffer
and always run in continuous mode.
- Fix PHTW register flow below 250 mbps.
- Fix clock control flow so that the warning message
“MSTP status timeout” is not displayed and when UDS (scaling)
is executed at VIN0, a black screen does not come out.
- Fix streaming procedure when resuming.
[Audio driver]
- Playback or capture doesn’t resume after Suspend to RAM.
[USB2.0 Function]
- Kernel error occurs with rmmod of g_printer.
- The dd command error occurs with g_mass_storage.
[USB2.0 Host driver]
- When connecting USB mouse, “Bad mode in Error handler” may occur with
Suspend to RAM.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
CAS only supports H3 (SoC: r8a7795), M3 (SoC: r8a7796).
This commit adds a python function to disable CAS automatically and show
the warning message as below in case of wrong setup.
| WARNING: linux-renesas-4.14.0+gitAUTOINC+4a7e26bdbc-r1 do_cas_checking:
| CAS only supports H3 (SoC: r8a7795), M3 (SoC: r8a7796), this feature will be disabled automatically
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit modifies recipe to enable RPMSG_VIRTIO config depend on
ICCOM distro feature.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit adds support E3 and upgrades Linux BSP to v3.6.1 for
the following updates:
[Kernel]
- Add R-Car E3 support.
- Fix Gfx clock.
[Power Management]
- Register clock for all cpu nodes for R-Car H3 to device tree.
- Improve to build only when enabling RCAR_POWER_AVS.
- Update IPA for CA53, need tune "contribution" parameter.
- Fix section mismatch build warnings.
- Fix double source of drivers/soc/renesas/Kconfig.
[Display driver]
- Fix continuous mode for dual pipelines.
- Fix DISP interrupt enable order, DPPR register set order and LVDS
startup sequence.
- Fix LVDS startup on R-Car Series, 3rd Generation.
- Fix LVDS stop sequence.
[DMA Engine driver]
- Fix max_chunk_size for R-Car Series, 3rd Generation.
- Check the done lists in rcar_dmac_chan_get_residue().
[I2C driver]
- Fix the problem that the strange data transfers with DMA transmit.
[IPMMU driver]
- Fix sequence issue.
[SD/MMC driver]
- Fix handling of SET_BLOCK_COUNT for RPMB.
[USB3.0 Function]
- Fix oops in renesas_usb3_remove().
- Don't print a warning when setting link state for disabled ports.
[Video Capture driver]
- Fix transfer rate and phy register value. Add CPG reset release
procedure.
- Add bytes per line when opening device.
- Fix power management procedure when resuming.
- Add MSTP status check after CPG reset.
- Fix division procedure for __udivdi3 error.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
Linux BSP v3.6.1 has been updated.
This reverts commit f8e4fb869abdfac3211b5f933202644901eeac7a.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
The M3ULCB ES1.0 revision can not use CPUIdle for CA53 cores.
This commit modifies recipes to apply a patch that disables
CPUIdle support for CA53.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit modifies recipe to install USB 3.0 firmware to
kernel source and to enable USB 3.0 in kernel image.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit adds SCHED_DEBUG config fragment to support CAS.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit upgrades Linux BSP to v3.6.0 for supporting
Kernel v4.14 stable and updating following items:
[Kernel]
- Add support for WDIOF_CARDRESET.
[Power Management]
- Add missing iounmap to rcar_avs.c.
- Add big.LITTLE CAS support.
- Add CA53 CPUIdle support.
- Add CA53 EMS support.
- Add CA53 CPUFreq support.
[Audio driver]
- Confirm rmmod command operation of snd-soc-rcar.
- Skip disabled-SSI nodes.
- Care ssi_parent_mod and remove NULL check from
rsnd_mod_name()/rsnd_mod_id().
- Revert IOMMU support so far.
- Don't use runtime->sample_bits.
- More clear rsnd_get_dalign() for DALIGN.
- Clear SSI_MODE for non TDM Extended modes.
[Display driver]
- Confirm the Fence function.
- Add support for colorkey alpha blending.
- Disable vsp1 interrupt when startup.
[DMA Engine driver]
- Fix array-bounds warning refer chcr_ts[].
[PWM driver]
- Enable PWM2 in device tree.
[USB2.0 Function]
- Fix the problem that the interrupt becomes long time when
disconnecting the USB cable.
[Video Capture driver]
- Add V4L2_FIELD_SEQ_TB/BT function support.
- Add ARGB8888 caputre format support and overflow debug message
option.
- Fix cropping procedure.
[RWDT driver]
- Add support for WDIOF_CARDRESET.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
Khang Nguyen
Khang Nguyen
Takeshi Kihara
Thuy Tran