Age | Commit message (Collapse) | Author | Files | Lines |
|
The ADSP on Renesas SoCs required a reserved memory area to become
enabled, and this needs to be done manually.
This patch adds sound hardware abstraction information for the m3ulcb
and m3ulcb-kf (kingfisher) device trees. This is helpful on-board the
ADSP for dynamically determining sound hardware at runtime, allowing
single binaries to be used between the two boards.
Future work will incorporate the h3ulcb and Salvator boards into the
abstraction.
Bug-AGL: SPEC-1424
Change-Id: Ie3f3d2227e79a6396f056fc63ecbcc6c73034e6b
Signed-off-by: Mark Farrugia <mark.farrugia@fiberdyne.com.au>
|
|
Implements the patches required to interface with the HiFi2 Xtensa ADSP
core on BSP 4.14, including M3ULCB, Kingfisher, and Salvator boards.
Bug-AGL: SPEC-1227
Change-Id: I9e58f89bdd93db595b8ec7a77b9261a9438e4878
Signed-off-by: Mark Farrugia <mark.farrugia@fiberdyne.com.au>
|
|
This adds support in the kernel for the GMSL Camera board
available for Kingfisher:
http://www.shimafuji.co.jp/DL/EN/InfotainmentCarrierBoard/#GMSL02
Instructions on how to use the board are also available:
https://elinux.org/R-Car/Tests:rcar-vin#Multi-channel_CSI-2_tests
Change-Id: Ib9da998be2018467284d54b977aff38158dba472
Signed-off-by: Stephane Desneux <stephane.desneux@iot.bzh>
Signed-off-by: Ronan Le Martret <ronan.lemartret@iot.bzh>
|
|
CAS only supports H3 (SoC: r8a7795), M3 (SoC: r8a7796).
This commit adds a python function to disable CAS automatically and show
the warning message as below in case of wrong setup.
| WARNING: linux-renesas-4.14.0+gitAUTOINC+4a7e26bdbc-r1 do_cas_checking:
| CAS only supports H3 (SoC: r8a7795), M3 (SoC: r8a7796), this feature will be disabled automatically
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit modifies recipe to enable RPMSG_VIRTIO config depend on
ICCOM distro feature.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit adds support E3 and upgrades Linux BSP to v3.6.1 for
the following updates:
[Kernel]
- Add R-Car E3 support.
- Fix Gfx clock.
[Power Management]
- Register clock for all cpu nodes for R-Car H3 to device tree.
- Improve to build only when enabling RCAR_POWER_AVS.
- Update IPA for CA53, need tune "contribution" parameter.
- Fix section mismatch build warnings.
- Fix double source of drivers/soc/renesas/Kconfig.
[Display driver]
- Fix continuous mode for dual pipelines.
- Fix DISP interrupt enable order, DPPR register set order and LVDS
startup sequence.
- Fix LVDS startup on R-Car Series, 3rd Generation.
- Fix LVDS stop sequence.
[DMA Engine driver]
- Fix max_chunk_size for R-Car Series, 3rd Generation.
- Check the done lists in rcar_dmac_chan_get_residue().
[I2C driver]
- Fix the problem that the strange data transfers with DMA transmit.
[IPMMU driver]
- Fix sequence issue.
[SD/MMC driver]
- Fix handling of SET_BLOCK_COUNT for RPMB.
[USB3.0 Function]
- Fix oops in renesas_usb3_remove().
- Don't print a warning when setting link state for disabled ports.
[Video Capture driver]
- Fix transfer rate and phy register value. Add CPG reset release
procedure.
- Add bytes per line when opening device.
- Fix power management procedure when resuming.
- Add MSTP status check after CPG reset.
- Fix division procedure for __udivdi3 error.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
Linux BSP v3.6.1 has been updated.
This reverts commit f8e4fb869abdfac3211b5f933202644901eeac7a.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
The M3ULCB ES1.0 revision can not use CPUIdle for CA53 cores.
This commit modifies recipes to apply a patch that disables
CPUIdle support for CA53.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit modifies recipe to install USB 3.0 firmware to
kernel source and to enable USB 3.0 in kernel image.
Signed-off-by: Khang Nguyen <khang.nguyen.xv@rvc.renesas.com>
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit adds SCHED_DEBUG config fragment to support CAS.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit upgrades Linux BSP to v3.6.0 for supporting
Kernel v4.14 stable and updating following items:
[Kernel]
- Add support for WDIOF_CARDRESET.
[Power Management]
- Add missing iounmap to rcar_avs.c.
- Add big.LITTLE CAS support.
- Add CA53 CPUIdle support.
- Add CA53 EMS support.
- Add CA53 CPUFreq support.
[Audio driver]
- Confirm rmmod command operation of snd-soc-rcar.
- Skip disabled-SSI nodes.
- Care ssi_parent_mod and remove NULL check from
rsnd_mod_name()/rsnd_mod_id().
- Revert IOMMU support so far.
- Don't use runtime->sample_bits.
- More clear rsnd_get_dalign() for DALIGN.
- Clear SSI_MODE for non TDM Extended modes.
[Display driver]
- Confirm the Fence function.
- Add support for colorkey alpha blending.
- Disable vsp1 interrupt when startup.
[DMA Engine driver]
- Fix array-bounds warning refer chcr_ts[].
[PWM driver]
- Enable PWM2 in device tree.
[USB2.0 Function]
- Fix the problem that the interrupt becomes long time when
disconnecting the USB cable.
[Video Capture driver]
- Add V4L2_FIELD_SEQ_TB/BT function support.
- Add ARGB8888 caputre format support and overflow debug message
option.
- Fix cropping procedure.
[RWDT driver]
- Add support for WDIOF_CARDRESET.
Signed-off-by: Thuy Tran <thuy.tran.xh@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|