summaryrefslogtreecommitdiffstats
path: root/meta-rcar-gen3/recipes-kernel/linux
AgeCommit message (Collapse)AuthorFilesLines
2017-04-19rcar-gen3: linux-renesas: Upgrade Linux BSP to v3.5.3Thao Nguyen1-2/+2
This commit upgrades Linux BSP to v3.5.3 and adds device tree file for M3 Salvator-XS board to salvator-x.conf. Linux BSP to v3.5.3 updates following items: Kernel core - Add workaround for PRR register of R-Car M3 WS1.1. (Fix printing cpu info.) - Add device tree file for Salvator-XS board with R-Car M3. - Fix R-Car M3 Salvator-X device tree file for MIX function of Audio driver. Power Management - Mark the OPP to be used during system suspend. - Enable CPUIdle function. - Apply new CPUIdle parameters. Audio driver - Confirm this driver can resume with Suspend to RAM during capture. - Avoid SSI_MODEx settings for SSI8. - Clear DE bit only in PDMACHCR when it stops. - Tidyup Audio-DMAC channel for DVC. - Enable PCM RATE until 192000. - Fix the setting of saved_rate during the resume process. Display driver - Fix the problem that the flicker may occur during rendering by the application. - Add brs option check for VGA connector. - Add routing set for digital RGB previously. DMA Engine driver - Fix release resources after interrupt process. Ethernet driver - Add phy-reset-gpios. This driver can work after Suspend to RAM with Salvator-XS board. - Fix GIS_PTMF bit clearing in ravb_ptp_interrupt. I2C driver - Revert and fix about unnecessary function related to Suspend to RAM. MSIOF driver - Fix SPI division value setting of R-Car M3 based on hardware specification. - Allow interrupts during msiof slave mode transfer wait. - Revert and fix about unnecessary function related to Suspend to RAM. RWDT driver - Fix timeout count calculation. SCIF/HSCIF driver - Fix panic when serial console and DMA are enabled. - Revert about unnecessary function related to Suspend to RAM. SD/MMC driver - Wait for CBSY instead of SCLKDIVEN. - Add re-tuning condition. - Add internal DMAC reset at startup. - Add the driver strength setting. eMMC HS400 mode can work with R-Car M3 WS1.1 on Salvator-XS board. Thermal driver - Fix to support thermal for both M3 WS1.0 and WS1.1. Video Capture driver - Fix resuming procedure. - Fix first field detection control. - Fix 720x480p transfer rate. - Fix video standard selection register setting. Change-Id: I3b0d6237c9d0c56a9f2870f1fde89ea215f163cd Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-03-23rcar-gen3: linux-renesas: Update BSP to v3.5.2 and change coding styleThao Nguyen10-11532/+4
This commit updates version of Linux BSP v3.5.1 -> v3.5.2 to fix following issues: [v3.5.2] - Display driver [H/W Restriction No.54] + In R-Car H3 WS1.x, distortion appears on the screen, when IPMMU is enabled. But this problem is fixed with R-Car H3 WS2.0. - Video Capture driver + Fix remove procedure. - Add board Salvator-XS and H3 WS 2.0 support. It also modifies the linux-renesas_4.9.bb to change the way common files are included. There is no difference in kernel config files of Salvator-X, H3ULCB and M3ULCB so far. Hence, we only need to install one file to avoid confusion. Change-Id: I145e0a7696f97fe1841a8a213c51c5685ada0290 Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com> Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
2017-01-27First commit.Renesas-Yocto-v2.16.0Takamitsu Honda10-0/+17315
Renesas BSP v3.5.1 (kernel v4.9 stable) [Environment] poky: yocto-2.1.2 (cca8dd15c8096626052f6d8d25ff1e9a606104a3) meta-openembedded: 55c8a76da5dc099a7bc3838495c672140cedb78e meta-linaro: 2f51d38048599d9878f149d6d15539fb97603f8f [Information] - U-boot: Changed load address from H'49000000 to H'50000000 - XDG_RUNTIME_DIR has been changed from "/run/user/root" to "/run/user/0" - Change location of include directory, which stores common user header files, to $(INCSHARED) - In BSP Only, core-image-weston is not supported even though local-wayland.conf is provided. - Please set Salvator-x SW7 Pin-1. In after Yocto BSP v2.12.0, it is  necessary to enable BKUP_TRG signal for Suspend to RAM. - The dtb filename was changed in R-Car H3. Only "Image-r8a7795-es1-salvator-x.dtb" is supported in this version. Please use "Image-r8a7795-es1-salvator-x.dtb" It supports R-Car H3 WS1.0 and WS1.1. - Please update your local.conf and bblayers.conf corresponding to Yocto v2.16.0 package. You can refer to meta-rcargen3/docs/sample/conf/ for updated contents. - You have to re-compile out-of-recipe software like user application by v2.16.0 SDK toolchains. - In some boards, the resuming from System Suspend to RAM may cause unstable operation or failed to resume. Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>