| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This commit updates Linux BSP from v3.5.3 to v3.5.5
for following items:
Kernel core
- Add ZG clock divider support.
- Revert and fix about Suspend to RAM.
- Add DEVFREQ support for GSX.
- Add usb companion property in EHCI.
- Add USB3.0 peripheral device node.
- Use IPMMU(MMU mode) for IPMMU-VP and IPMMU-VC0/1
with R-Car H3 Ver.1.x,
for IPMMU-VP0/1 and IPMMU-VC0/1 with R-Car H3 Ver.2.0,
in IPMMUVC0 with R-Car M3.
- Add override support for the actual number of MMU contexts.
- Fix audio Mix support on DTSI.
Power Management
- Cleanup AVS driver.
- Update voltage for VDD_DVFS and VDD.
Audio driver
- Resolve 16bit/24bit capture noise problem by enabling
clock-frequency for both 4.1kHz/48kHz
and fixing possible NULL pointer dereference.
- Resolve playback problem of sampling rate 32kHz, 176.4kHz and
192kHz by enabling clock-frequency for both 44.1kHz/48kHz.
- Resolve “can’t get dma channel” error at the time of
unbind/bind by fixing up of_clk_add_provider() usage for multi clkout
and calling the missing of_clk_del_provider() when removing.
- Resolve 48kHz audio 1-20k sweep noise problem
by enabling clock-frequency 44.1kHz/48kHz.
- Merge rsnd_kctrl_new_m/s/e into rsnd_kctrl_new().
- Fix 24bit capture noise problem
by not using PDTA bit for 24bit on SSI.
- Request/Release DMA channel each time
for avoiding error of getting dma channel.
Display driver
- Use dma_map_sg_attrs to skip synchronization of the CPU cache.
- Add mode_fixup callback function.
- Control clock of bridge during S2RAM and change to control clock
via clock driver.
- Fix reserved register setting for R-Car for H/W manual update.
- Add null pointer check for brs option.
- Revert "drm: bridge/dw-hdmi: Add HDP interrupt disable
for suspend".
- Fix hierarchy of driver structure for clk-5p49x.
DMA Engine driver
- Revert dma pause function because it was rejected by upstream.
GPIO driver
- Revert and fix about Suspend to RAM.
- Add GP-1-28 port pin support for R-Car H3 Ver.2.0
because of H/W manual updating to Rev.0.54E.
Modify just PFC and DT.
SCIF/HSCIF driver
- Resolve system freezing.
SD/MMC driver
- Add initial setting of interrupt mask register.
- Fix command sequence at error detection.
- Fix “Wait for CBSY instead of SCLKDIVEN”.
- Fix processing when detecting SCC error and fix error handling
when issuing CMD23.
- Fix reset_hs400_mode.
- Fix problem that SDIO interrupt may be missed.
USB3.0 Function
- Add Role-change support.
- Add DMA support.
- Add basic function support.
USB2.0 Host driver
- Fix mouse connection time (2 second or more) when resuming.
USB3.0 Host driver
- Support for R-Car Gen3 USB 3.0 PHY for SSC function.
- Add R-Car Gen3 USB 2.0 clock selector PHY,
support for R-Car Gen3 USB 3.0 PHY.
Video Capture driver
- Add 2 lane support with rcar-csi2.c.
- Fix image alignment for setting pre clipping.
- Fix wait time for software reset in rcar-csi2.c
because of H/W manual updating to Rev.0.54E.
- Fix PHY initialization in rcar-csi2.c
because of H/W manual updating to Rev.0.54E.
- Fix PHTW register setting in rcar-csi2.c
because of H/W manual updating toRev.0.54E.
- Fix wait procedure usleep_range from msleep in adv7482.c.
- Fix channel get procedure.
Signed-off-by: Thao Nguyen <thao.nguyen.yb@renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit upgrades Linux BSP to v3.5.3
and adds device tree file for M3 Salvator-XS board to salvator-x.conf.
Linux BSP to v3.5.3 updates following items:
Kernel core
- Add workaround for PRR register of R-Car M3 WS1.1.
(Fix printing cpu info.)
- Add device tree file for Salvator-XS board with R-Car M3.
- Fix R-Car M3 Salvator-X device tree file for MIX function
of Audio driver.
Power Management
- Mark the OPP to be used during system suspend.
- Enable CPUIdle function.
- Apply new CPUIdle parameters.
Audio driver
- Confirm this driver can resume with Suspend to RAM during capture.
- Avoid SSI_MODEx settings for SSI8.
- Clear DE bit only in PDMACHCR when it stops.
- Tidyup Audio-DMAC channel for DVC.
- Enable PCM RATE until 192000.
- Fix the setting of saved_rate during the resume process.
Display driver
- Fix the problem that the flicker may occur during rendering
by the application.
- Add brs option check for VGA connector.
- Add routing set for digital RGB previously.
DMA Engine driver
- Fix release resources after interrupt process.
Ethernet driver
- Add phy-reset-gpios.
This driver can work after Suspend to RAM with Salvator-XS board.
- Fix GIS_PTMF bit clearing in ravb_ptp_interrupt.
I2C driver
- Revert and fix about unnecessary function related to Suspend to RAM.
MSIOF driver
- Fix SPI division value setting of R-Car M3
based on hardware specification.
- Allow interrupts during msiof slave mode transfer wait.
- Revert and fix about unnecessary function related to Suspend to RAM.
RWDT driver
- Fix timeout count calculation.
SCIF/HSCIF driver
- Fix panic when serial console and DMA are enabled.
- Revert about unnecessary function related to Suspend to RAM.
SD/MMC driver
- Wait for CBSY instead of SCLKDIVEN.
- Add re-tuning condition.
- Add internal DMAC reset at startup.
- Add the driver strength setting.
eMMC HS400 mode can work with R-Car M3 WS1.1 on Salvator-XS board.
Thermal driver
- Fix to support thermal for both M3 WS1.0 and WS1.1.
Video Capture driver
- Fix resuming procedure.
- Fix first field detection control.
- Fix 720x480p transfer rate.
- Fix video standard selection register setting.
Change-Id: I3b0d6237c9d0c56a9f2870f1fde89ea215f163cd
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
This commit updates version of Linux BSP v3.5.1 -> v3.5.2
to fix following issues:
[v3.5.2]
- Display driver [H/W Restriction No.54]
+ In R-Car H3 WS1.x, distortion appears on the screen,
when IPMMU is enabled.
But this problem is fixed with R-Car H3 WS2.0.
- Video Capture driver
+ Fix remove procedure.
- Add board Salvator-XS and H3 WS 2.0 support.
It also modifies the linux-renesas_4.9.bb to change the way common files
are included.
There is no difference in kernel config files of Salvator-X, H3ULCB and
M3ULCB so far.
Hence, we only need to install one file to avoid confusion.
Change-Id: I145e0a7696f97fe1841a8a213c51c5685ada0290
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
|
Renesas BSP v3.5.1 (kernel v4.9 stable)
[Environment]
poky: yocto-2.1.2 (cca8dd15c8096626052f6d8d25ff1e9a606104a3)
meta-openembedded: 55c8a76da5dc099a7bc3838495c672140cedb78e
meta-linaro: 2f51d38048599d9878f149d6d15539fb97603f8f
[Information]
- U-boot: Changed load address from H'49000000 to H'50000000
- XDG_RUNTIME_DIR has been changed from "/run/user/root" to "/run/user/0"
- Change location of include directory, which stores common user header
files, to $(INCSHARED)
- In BSP Only, core-image-weston is not supported even though
local-wayland.conf is provided.
- Please set Salvator-x SW7 Pin-1. In after Yocto BSP v2.12.0, it is
necessary to enable BKUP_TRG signal for Suspend to RAM.
- The dtb filename was changed in R-Car H3. Only
"Image-r8a7795-es1-salvator-x.dtb" is supported in this version.
Please use "Image-r8a7795-es1-salvator-x.dtb" It supports R-Car H3
WS1.0 and WS1.1.
- Please update your local.conf and bblayers.conf corresponding to Yocto
v2.16.0 package. You can refer to meta-rcargen3/docs/sample/conf/ for
updated contents.
- You have to re-compile out-of-recipe software like user application by
v2.16.0 SDK toolchains.
- In some boards, the resuming from System Suspend to RAM may cause
unstable operation or failed to resume.
Signed-off-by: Takamitsu Honda <takamitsu.honda.pv@renesas.com>
|
Thao Nguyen
Thao Nguyen
Takamitsu Honda