summaryrefslogtreecommitdiffstats
path: root/getting-started
diff options
context:
space:
mode:
authorRomain Forlot <romain.forlot@iot.bzh>2016-12-28 15:14:19 +0100
committerronan [iot.bzh] <ronan22@users.noreply.github.com>2017-01-03 17:17:08 +0100
commit6b7ebe38cd16d678a7bd6d5e4d6047159bc0897a (patch)
tree58ef0e4a6f798e64de66f88f37cee8e82b426e0b /getting-started
parente6378370da42eec83a6997e7d14a517e50f12c81 (diff)
Fix, remove redundant section and merged with its parent
Change-Id: Ia090edb6bcc646d6de2e2a38d6cb1968d3845090 Signed-off-by: Romain Forlot <romain.forlot@iot.bzh>
Diffstat (limited to 'getting-started')
-rw-r--r--getting-started/machines/R-Car-Starter-Kit-gen3.md63
1 files changed, 4 insertions, 59 deletions
diff --git a/getting-started/machines/R-Car-Starter-Kit-gen3.md b/getting-started/machines/R-Car-Starter-Kit-gen3.md
index 2091382..11566b4 100644
--- a/getting-started/machines/R-Car-Starter-Kit-gen3.md
+++ b/getting-started/machines/R-Car-Starter-Kit-gen3.md
@@ -442,11 +442,13 @@ Hit any key to stop autoboot: 0
## Configure U-boot parameters
+Follow the steps below to configure the boot from microSD card and to set screen resolution:
+
* Turn the board on using the power switch.
* Hit any key to stop autoboot (warning you have only few seconds).
-* Check if you have correct parameters for booting your board:
+* Type **print** to check if you have correct parameters for booting your board:
* For machine m3ulcb:
-
+
```
=> print
baudrate=115200
@@ -518,63 +520,6 @@ saveenv
run bootcmd
```
-### U-Boot screen configuration
-
-Follow the steps below to configure the boot from microSD card and to set screen resolution:
-
-* Power up the board
-* Using your preferred terminal emulator, type a character to abort the boot and enter the U-boot menu
-* Type **print** to check the environment:
-
-```
-print
-```
-
-* Verify that the ethaddr environment variable is set to the same MAC address value shown on the label on top of the RJ45 Ethernet connector.
-* If not, set it using the following command:
-
-```
-setenv ethaddr <MAC address>
-```
-
-For example:
-
-```
-setenv ethaddr 2e:09:0a:00:75:b5
-```
-
-* Set the follow environment variables:
-
-```
-setenv bootargs_console 'console=ttySC6,38400 ignore_loglevel'
-setenv bootargs_video 'vmalloc=384M video=HDMI-A-1:1920x1080-32@60'
-setenv bootargs_root 'root=/dev/mmcblk0p1 rootdelay=3 rw rootfstype=ext4 rootwait'
-setenv bootmmc '1:1'
-setenv bootcmd_sd 'ext4load mmc ${bootmmc} 0x40007fc0 boot/uImage+dtb'
-setenv bootcmd 'setenv bootargs ${bootargs_console} ${bootargs_video} ${bootargs_root}; run bootcmd_sd; bootm 0x40007fc0'
-```
-
-**WARNINGS:**
-If no display shows up when booting, e.g. for a non-full HD screen, replace **1920x1080** value in the **bootargs_video** variable with lower screen resolution such as **1024x768**.
- Unfortunately at the moment, there is no universally supported setting.
-
-For Renesas h3ulcb use screen resolution **1024x768** and set **bootmmc** to **2:1**.
-
-* Save the environment variables:
-
-```
-saveenv
- Saving Environment to SPI Flash...
- SF: Detected S25FL512S with page size 256 KiB, total 64 MiB
- Erasing SPI flash...Writing to SPI flash...done
-```
-
-* Reboot:
-
-```
-reset
-```
-
## Console boot
After booting, you should see the wayland display on the external monitor and a login prompt on the console, such as: