diff options
Diffstat (limited to 'security-blueprint/part-2')
| -rw-r--r-- | security-blueprint/part-2/0_Abstract.md | 58 | ||||
| -rw-r--r-- | security-blueprint/part-2/1-Image.md | 52 | ||||
| -rw-r--r-- | security-blueprint/part-2/2-Communication-modes.md | 89 | ||||
| -rw-r--r-- | security-blueprint/part-2/3-Consoles.md | 107 |
4 files changed, 306 insertions, 0 deletions
diff --git a/security-blueprint/part-2/0_Abstract.md b/security-blueprint/part-2/0_Abstract.md new file mode 100644 index 0000000..5ebb750 --- /dev/null +++ b/security-blueprint/part-2/0_Abstract.md @@ -0,0 +1,58 @@ +# Part 2 - Secure boot + +## Abstract + +<!-- todo --> + +Domain | Improvement +--------------- | ---------------------------------------------------- +Boot-Abstract-1 | More generic and add examples (The chain of trust). + +<!-- endtodo --> + +**Boot Hardening**: Steps/requirements to configure the boot sequence, in order +to restrict the device from executing anything other than the approved software +image. + +In this part, we will see a series of settings that will allow us to improve +security during boot phase. For the purposes of reference and explanation, we +are providing guidance on how to configure an embedded device that runs with a +3.10.17 Linux kernel. If the integrity is not checked or if a critical error +occurs, the system must boot on a very stable backup image. + +**Requirements**: These requirements must be met even if an alternative version +of the Linux kernel is chosen. + +**Recommendations**: Detailed best practices that should be applied in order to +secure a device. Although they are not currently listed as hard requirements, +they may be upgraded to requirements status in the future. In addition, specific +operators may change some of these recommendations into requirements based on +their specific needs and objectives. + +<!-- todo --> + +Domain | Improvement +--------------- | ------------------------------------------- +Boot-Abstract-1 | Review the definition of the "boot loader". + +<!-- endtodo --> + +**Boot loader**: The boot loader consists of the Primary boot loader residing +in **OTP** memory, sboot, U-Boot and Secure loader residing in external flash +(NAND or SPI/NOR flash memory). The CPU on power on or reset executes the +primary boot loader. The **OTP** primary boot loader makes the necessary initial +system configuration and then loads the secondary boot loader sboot from +external flash memory to ram memory. The sboot then loads the U-Boot along with +the Secure loader. U-Boot then verifies the Kernel/system image integrity, then +loads the Kernel/system image before passing control to it. + +-------------------------------------------------------------------------------- + +## Acronyms and Abbreviations + +The following table lists the terms utilized within this part of the document. + +Acronyms or Abbreviations | Description +------------------------- | --------------------------------- +_FUSE_ | **F**ilesystem in **U**ser**S**pac**E** +_OTP_ | **O**ne-**T**ime-**P**rogrammable diff --git a/security-blueprint/part-2/1-Image.md b/security-blueprint/part-2/1-Image.md new file mode 100644 index 0000000..c0eb0b6 --- /dev/null +++ b/security-blueprint/part-2/1-Image.md @@ -0,0 +1,52 @@ +# Image + +## Image selection + +The boot process shall be uninterruptible and shall irrevocably boot the image +as specified in the boot environment. + +In U-Boot set the "_bootdelay_" environment variable and/or define +`CONFIG_BOOTDELAY` to _-2_. + +<!-- config --> + +Domain | _Variable_ / `Config` name | `Value` +---------------------- | -------------------------- | ------- +Boot-Image-Selection-1 | `CONFIG_BOOTDELAY` | `-2` +Boot-Image-Selection-2 | _bootdelay_ | `-2` + +<!-- endconfig --> + +-------------------------------------------------------------------------------- + +## Image authenticity + +It shall not be possible to boot from an unverified image. The secure boot +feature in U-Boot shall be enabled. The secure boot feature is available from +U-Boot 2013.07 version. To enable the secure boot feature, enable the following +features: + +``` +CONFIG_FIT: Enables support for Flat Image Tree (FIT) uImage format. +CONFIG_FIT_SIGNATURE: Enables signature verification of FIT images. +CONFIG_RSA: Enables RSA algorithm used for FIT image verification. +CONFIG_OF_CONTROL: Enables Flattened Device Tree (FDT) configuration. +CONFIG_OF_SEPARATE: Enables separate build of u-Boot from the device tree. +CONFIG_DEFAULT_DEVICE_TREE: Specifies the default Device Tree used for the run-time configuration of U-Boot. +``` + +Generate the U-Boot image with public keys to validate and load the image. It +shall use RSA2048 and SHA256 for authentication. + +<!-- config --> + +Domain | `Config` name | _State_ +------------------------- | ---------------------------- | -------- +Boot-Image-Authenticity-1 | `CONFIG_FIT` | _Enable_ +Boot-Image-Authenticity-2 | `CONFIG_FIT_SIGNATURE` | _Enable_ +Boot-Image-Authenticity-3 | `CONFIG_RSA` | _Enable_ +Boot-Image-Authenticity-4 | `CONFIG_OF_CONTROL` | _Enable_ +Boot-Image-Authenticity-5 | `CONFIG_OF_SEPARATE` | _Enable_ +Boot-Image-Authenticity-6 | `CONFIG_DEFAULT_DEVICE_TREE` | _Enable_ + +<!-- endconfig --> diff --git a/security-blueprint/part-2/2-Communication-modes.md b/security-blueprint/part-2/2-Communication-modes.md new file mode 100644 index 0000000..d3a823c --- /dev/null +++ b/security-blueprint/part-2/2-Communication-modes.md @@ -0,0 +1,89 @@ +# Communication modes + +## Disable USB, Serial and Docsis Support + +To disable USB support in U-Boot, following config's shall not be defined: + +``` +CONFIG_CMD_USB: Enables basic USB support and the usb command. +CONFIG_USB_UHCI: Defines the lowlevel part. +CONFIG_USB_KEYBOARD: Enables the USB Keyboard. +CONFIG_USB_STORAGE: Enables the USB storage devices. +CONFIG_USB_HOST_ETHER: Enables USB Ethernet adapter support. +``` + +In addition, disable unnecessary communication modes like Ethernet, Serial +ports, DOCSIS in U-Boot and sboot that are not necessary. + +Linux Kernel support for USB should be compiled-out if not required. If it is +needed, the Linux Kernel should be configured to only enable the minimum +required USB devices. User-initiated USB-filesystems should be treated with +special care. Whether or not the filesystems are mounted in userspace +(**FUSE**), restricted mount options should be observed. + +<!-- config --> + +Domain | Communication modes | _State_ +-------------------- | ------------------------- | -------------------------------------------------------------------------------------------------------------------------------------- +Boot-Communication-1 | `USB` | _Disabled_ and _Compiled-out_ if not required. +Boot-Communication-2 | `USB` | Else, Kernel should be configured to only enable the minimum required USB devices and filesystems should be treated with special care. +Boot-Communication-3 | `Ethernet` | _Disabled_ +Boot-Communication-4 | U-boot and sboot `DOCSIS` | _Disabled_ +Boot-Communication-5 | `Serial ports` | _Disabled_ + +<!-- endconfig --> <!-- config --> + +Domain | `Config` name | _State_ +------------------------ | ----------------------- | ------------- +Boot-Communication-USB-1 | `CONFIG_CMD_USB` | _Not defined_ +Boot-Communication-USB-2 | `CONFIG_USB_UHCI` | _Not defined_ +Boot-Communication-USB-3 | `CONFIG_USB_KEYBOARD` | _Not defined_ +Boot-Communication-USB-4 | `CONFIG_USB_STORAGE` | _Not defined_ +Boot-Communication-USB-5 | `CONFIG_USB_HOST_ETHER` | _Not defined_ + +<!-- endconfig --> + +-------------------------------------------------------------------------------- + +## Disable all Network Interfaces + +Preferably no network interface is allowed, but if required, then the enabled +services should be restricted to only those used. + +<!-- config --> + +Domain | Communication modes | _State_ +-------------------- | -------------------- | --------------------------------------------------------------------------------------------- +Boot-Communication-1 | `Network interfaces` | Preferably _no network interface is allowed_, otherwise, restrict the services to those used. + +<!-- endconfig --> + +## Remove or Disable Unnecessary Services, Ports, and Devices + +Restrict the `services`, `ports` and `devices` to those used. + +<!-- config --> + +Domain | Object | Recommendations +-------------------- | --------------------------------- | ------------------------------------------------------------- +Boot-Communication-1 | `Services`, `ports` and `devices` | Restrict the `services`, `ports` and `devices` to those used. + +<!-- endconfig --> + +## Disable flash access + +**Recommendation**: + +In U-Boot following flash memory commands shall be disabled: + +**NAND**: Support for nand flash access available through `do_nand` has to be disabled. + +<!-- config --> + +Domain | `Command` name | _State_ +-------------------------- | -------------- | --------- +Boot-Communication-Flash-1 | `do_nand` | _Disable_ + +<!-- endconfig --> + +Similarly sboot should disable flash access support through command line if any. diff --git a/security-blueprint/part-2/3-Consoles.md b/security-blueprint/part-2/3-Consoles.md new file mode 100644 index 0000000..5adad3f --- /dev/null +++ b/security-blueprint/part-2/3-Consoles.md @@ -0,0 +1,107 @@ +# Consoles + +## Disable serial console + +Serial console output shall be disabled. To disable console output in U-Boot, +set the following macros: + +<!-- config --> + +Domain | `Config` name | `Value` +---------------------- | --------------------------------------- | --------- +Boot-Consoles-Serial-1 | `CONFIG_SILENT_CONSOLE` | `Disable` +Boot-Consoles-Serial-2 | `CONFIG_SYS_DEVICE_NULLDEV` | `Disable` +Boot-Consoles-Serial-3 | `CONFIG_SILENT_CONSOLE_UPDATE_ON_RELOC` | `Disable` + +<!-- endconfig --> <!-- todo --> + +Domain | Improvement +--------------- | ------------------------------------ +Boot-Consoles-1 | Secure loader: No reference earlier? + +<!-- endtodo --> + +And set "**silent**" environment variable. For the Secure loader, disable the +traces by undefined the below macro: + +<!-- config --> + +Domain | `Environment variable` name | _State_ +---------------------- | --------------------------- | ------------- +Boot-Consoles-Serial-1 | `INC_DEBUG_PRINT` | _Not defined_ + +<!-- endconfig --> + +For sboot proper configuration needs to be done to disable the serial console. + +-------------------------------------------------------------------------------- + +<!-- pagebreak --> + +## Immutable environment variables + +In U-Boot, ensure Kernel command line, boot commands, boot delay and other +environment variables are immutable. This will prevent side-loading of alternate +images, by restricting the boot selection to only the image in FLASH. + +The environment variables shall be part of the text region in U-Boot as default +environment variable and not in non-volatile memory. + +Remove configuration options related to non-volatile memory, such as: + +<!-- config --> + +Domain | `Config` name | _State_ +-------------------------- | ---------------------------- | --------- +Boot-Consoles-Variables-1 | `CONFIG_ENV_IS_IN_MMC` | `#undef` +Boot-Consoles-Variables-2 | `CONFIG_ENV_IS_IN_EEPROM` | `#undef` +Boot-Consoles-Variables-3 | `CONFIG_ENV_IS_IN_FLASH` | `#undef` +Boot-Consoles-Variables-4 | `CONFIG_ENV_IS_IN_DATAFLASH` | `#undef` +Boot-Consoles-Variables-5 | `CONFIG_ENV_IS_IN_FAT` | `#undef` +Boot-Consoles-Variables-6 | `CONFIG_ENV_IS_IN_NAND` | `#undef` +Boot-Consoles-Variables-7 | `CONFIG_ENV_IS_IN_NVRAM` | `#undef` +Boot-Consoles-Variables-8 | `CONFIG_ENV_IS_IN_ONENAND` | `#undef` +Boot-Consoles-Variables-9 | `CONFIG_ENV_IS_IN_SPI_FLASH` | `#undef` +Boot-Consoles-Variables-10 | `CONFIG_ENV_IS_IN_REMOTE` | `#undef` +Boot-Consoles-Variables-11 | `CONFIG_ENV_IS_IN_UBI` | `#undef` +Boot-Consoles-Variables-12 | `CONFIG_ENV_IS_NOWHERE` | `#define` + +<!-- endconfig --> + +-------------------------------------------------------------------------------- + +<!-- pagebreak --> + +## (Recommendation) Removal of memory dump commands + +In U-Boot, following commands shall be disabled to avoid memory dumps: + +``` +md : Memory Display command. +mm : Memory modify command - auto incrementing address. +nm : Memory modify command - constant address. +mw : Memory write. +cp : Memory copy. +mwc : Memory write cyclic. +mdc : Memory display cyclic. +mtest : Simple ram read/write test. +loopw : Infinite write loop on address range. +``` + +<!-- config --> + +Domain | `Command` name | _State_ +----------------------- | -------------- | ---------- +Boot-Consoles-MemDump-1 | `md` | _Disabled_ +Boot-Consoles-MemDump-2 | `mm` | _Disabled_ +Boot-Consoles-MemDump-3 | `nm` | _Disabled_ +Boot-Consoles-MemDump-4 | `mw` | _Disabled_ +Boot-Consoles-MemDump-5 | `cp` | _Disabled_ +Boot-Consoles-MemDump-6 | `mwc` | _Disabled_ +Boot-Consoles-MemDump-7 | `mdc` | _Disabled_ +Boot-Consoles-MemDump-8 | `mtest` | _Disabled_ +Boot-Consoles-MemDump-9 | `loopw` | _Disabled_ + +<!-- endconfig --> + +Similarly, memory dump support shall be disabled from sboot. |