1 files changed, 537 insertions, 0 deletions
diff --git a/roms/u-boot/drivers/pinctrl/pinctrl-stmfx.c b/roms/u-boot/drivers/pinctrl/pinctrl-stmfx.c
new file mode 100644
index 000000000..fe7a59d43
--- /dev/null
+++ b/roms/u-boot/drivers/pinctrl/pinctrl-stmfx.c
@@ -0,0 +1,537 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+ *
+ * Driver for STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander
+ * based on Linux driver : pinctrl/pinctrl-stmfx.c
+ */
+#include <common.h>
+#include <dm.h>
+#include <i2c.h>
+#include <asm/gpio.h>
+#include <dm/device.h>
+#include <dm/device-internal.h>
+#include <dm/device_compat.h>
+#include <dm/lists.h>
+#include <dm/pinctrl.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <power/regulator.h>
+
+/* STMFX pins = GPIO[15:0] + aGPIO[7:0] */
+#define STMFX_MAX_GPIO			16
+#define STMFX_MAX_AGPIO			8
+
+/* General */
+#define STMFX_REG_CHIP_ID		0x00 /* R */
+#define STMFX_REG_FW_VERSION_MSB	0x01 /* R */
+#define STMFX_REG_FW_VERSION_LSB	0x02 /* R */
+#define STMFX_REG_SYS_CTRL		0x40 /* RW */
+
+/* MFX boot time is around 10ms, so after reset, we have to wait this delay */
+#define STMFX_BOOT_TIME_MS 10
+
+/* GPIOs expander */
+/* GPIO_STATE1 0x10, GPIO_STATE2 0x11, GPIO_STATE3 0x12 */
+#define STMFX_REG_GPIO_STATE		0x10 /* R */
+/* GPIO_DIR1 0x60, GPIO_DIR2 0x61, GPIO_DIR3 0x63 */
+#define STMFX_REG_GPIO_DIR		0x60 /* RW */
+/* GPIO_TYPE1 0x64, GPIO_TYPE2 0x65, GPIO_TYPE3 0x66 */
+#define STMFX_REG_GPIO_TYPE		0x64 /* RW */
+/* GPIO_PUPD1 0x68, GPIO_PUPD2 0x69, GPIO_PUPD3 0x6A */
+#define STMFX_REG_GPIO_PUPD		0x68 /* RW */
+/* GPO_SET1 0x6C, GPO_SET2 0x6D, GPO_SET3 0x6E */
+#define STMFX_REG_GPO_SET		0x6C /* RW */
+/* GPO_CLR1 0x70, GPO_CLR2 0x71, GPO_CLR3 0x72 */
+#define STMFX_REG_GPO_CLR		0x70 /* RW */
+
+/* STMFX_REG_CHIP_ID bitfields */
+#define STMFX_REG_CHIP_ID_MASK		GENMASK(7, 0)
+
+/* STMFX_REG_SYS_CTRL bitfields */
+#define STMFX_REG_SYS_CTRL_GPIO_EN	BIT(0)
+#define STMFX_REG_SYS_CTRL_ALTGPIO_EN	BIT(3)
+#define STMFX_REG_SYS_CTRL_SWRST	BIT(7)
+
+#define NR_GPIO_REGS			3
+#define NR_GPIOS_PER_REG		8
+#define get_reg(offset)			((offset) / NR_GPIOS_PER_REG)
+#define get_shift(offset)		((offset) % NR_GPIOS_PER_REG)
+#define get_mask(offset)		(BIT(get_shift(offset)))
+
+struct stmfx_pinctrl {
+	struct udevice *gpio;
+};
+
+static int stmfx_read(struct udevice *dev, uint offset)
+{
+	return  dm_i2c_reg_read(dev_get_parent(dev), offset);
+}
+
+static int stmfx_write(struct udevice *dev, uint offset, unsigned int val)
+{
+	return dm_i2c_reg_write(dev_get_parent(dev), offset, val);
+}
+
+static int stmfx_read_reg(struct udevice *dev, u8 reg_base, uint offset)
+{
+	u8 reg = reg_base + get_reg(offset);
+	u32 mask = get_mask(offset);
+	int ret;
+
+	ret = stmfx_read(dev, reg);
+	if (ret < 0)
+		return ret;
+
+	return ret < 0 ? ret : !!(ret & mask);
+}
+
+static int stmfx_write_reg(struct udevice *dev, u8 reg_base, uint offset,
+			   uint val)
+{
+	u8 reg = reg_base + get_reg(offset);
+	u32 mask = get_mask(offset);
+	int ret;
+
+	ret = stmfx_read(dev, reg);
+	if (ret < 0)
+		return ret;
+	ret = (ret & ~mask) | (val ? mask : 0);
+
+	return stmfx_write(dev, reg, ret);
+}
+
+static int stmfx_conf_set_pupd(struct udevice *dev, unsigned int offset,
+			       uint pupd)
+{
+	return stmfx_write_reg(dev, STMFX_REG_GPIO_PUPD, offset, pupd);
+}
+
+static int stmfx_conf_get_pupd(struct udevice *dev, unsigned int offset)
+{
+	return stmfx_read_reg(dev, STMFX_REG_GPIO_PUPD, offset);
+}
+
+static int stmfx_conf_set_type(struct udevice *dev, unsigned int offset,
+			       uint type)
+{
+	return stmfx_write_reg(dev, STMFX_REG_GPIO_TYPE, offset, type);
+}
+
+static int stmfx_conf_get_type(struct udevice *dev, unsigned int offset)
+{
+	return stmfx_read_reg(dev, STMFX_REG_GPIO_TYPE, offset);
+}
+
+static int stmfx_gpio_get(struct udevice *dev, unsigned int offset)
+{
+	return stmfx_read_reg(dev, STMFX_REG_GPIO_STATE, offset);
+}
+
+static int stmfx_gpio_set(struct udevice *dev, unsigned int offset, int value)
+{
+	u32 reg = value ? STMFX_REG_GPO_SET : STMFX_REG_GPO_CLR;
+	u32 mask = get_mask(offset);
+
+	return stmfx_write(dev, reg + get_reg(offset), mask);
+}
+
+static int stmfx_gpio_get_function(struct udevice *dev, unsigned int offset)
+{
+	int ret = stmfx_read_reg(dev, STMFX_REG_GPIO_DIR, offset);
+
+	if (ret < 0)
+		return ret;
+	/* On stmfx, gpio pins direction is (0)input, (1)output. */
+
+	return ret ? GPIOF_OUTPUT : GPIOF_INPUT;
+}
+
+static int stmfx_gpio_direction_input(struct udevice *dev, unsigned int offset)
+{
+	return stmfx_write_reg(dev, STMFX_REG_GPIO_DIR, offset, 0);
+}
+
+static int stmfx_gpio_direction_output(struct udevice *dev,
+				       unsigned int offset, int value)
+{
+	int ret = stmfx_gpio_set(dev, offset, value);
+	if (ret < 0)
+		return ret;
+
+	return stmfx_write_reg(dev, STMFX_REG_GPIO_DIR, offset, 1);
+}
+
+static int stmfx_gpio_set_flags(struct udevice *dev, unsigned int offset,
+				ulong flags)
+{
+	int ret = -ENOTSUPP;
+
+	if (flags & GPIOD_IS_OUT) {
+		bool value = flags & GPIOD_IS_OUT_ACTIVE;
+
+		if (flags & GPIOD_OPEN_SOURCE)
+			return -ENOTSUPP;
+		if (flags & GPIOD_OPEN_DRAIN)
+			ret = stmfx_conf_set_type(dev, offset, 0);
+		else /* PUSH-PULL */
+			ret = stmfx_conf_set_type(dev, offset, 1);
+		if (ret)
+			return ret;
+		ret = stmfx_gpio_direction_output(dev, offset, value);
+	} else if (flags & GPIOD_IS_IN) {
+		ret = stmfx_gpio_direction_input(dev, offset);
+		if (ret)
+			return ret;
+		if (flags & GPIOD_PULL_UP) {
+			ret = stmfx_conf_set_type(dev, offset, 1);
+			if (ret)
+				return ret;
+			ret = stmfx_conf_set_pupd(dev, offset, 1);
+		} else if (flags & GPIOD_PULL_DOWN) {
+			ret = stmfx_conf_set_type(dev, offset, 1);
+			if (ret)
+				return ret;
+			ret = stmfx_conf_set_pupd(dev, offset, 0);
+		}
+	}
+
+	return ret;
+}
+
+static int stmfx_gpio_get_flags(struct udevice *dev, unsigned int offset,
+				ulong *flagsp)
+{
+	ulong dir_flags = 0;
+	int ret;
+
+	if (stmfx_gpio_get_function(dev, offset) == GPIOF_OUTPUT) {
+		dir_flags |= GPIOD_IS_OUT;
+		ret = stmfx_conf_get_type(dev, offset);
+		if (ret < 0)
+			return ret;
+		if (ret == 0)
+			dir_flags |= GPIOD_OPEN_DRAIN;
+			/* 1 = push-pull (default), open source not supported */
+		ret = stmfx_gpio_get(dev, offset);
+		if (ret < 0)
+			return ret;
+		if (ret)
+			dir_flags |= GPIOD_IS_OUT_ACTIVE;
+	} else {
+		dir_flags |= GPIOD_IS_IN;
+		ret = stmfx_conf_get_type(dev, offset);
+		if (ret < 0)
+			return ret;
+		if (ret == 1) {
+			ret = stmfx_conf_get_pupd(dev, offset);
+			if (ret < 0)
+				return ret;
+			if (ret == 1)
+				dir_flags |= GPIOD_PULL_UP;
+			else
+				dir_flags |= GPIOD_PULL_DOWN;
+		}
+	}
+	*flagsp = dir_flags;
+
+	return 0;
+}
+
+static int stmfx_gpio_probe(struct udevice *dev)
+{
+	struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
+	struct ofnode_phandle_args args;
+	u8 sys_ctrl;
+
+	uc_priv->bank_name = "stmfx";
+	uc_priv->gpio_count = STMFX_MAX_GPIO + STMFX_MAX_AGPIO;
+	if (!dev_read_phandle_with_args(dev, "gpio-ranges",
+					NULL, 3, 0, &args)) {
+		uc_priv->gpio_count = args.args[2];
+	}
+
+	/* enable GPIO function */
+	sys_ctrl = STMFX_REG_SYS_CTRL_GPIO_EN;
+	if (uc_priv->gpio_count > STMFX_MAX_GPIO)
+		sys_ctrl |= STMFX_REG_SYS_CTRL_ALTGPIO_EN;
+	stmfx_write(dev, STMFX_REG_SYS_CTRL, sys_ctrl);
+
+	return 0;
+}
+
+static const struct dm_gpio_ops stmfx_gpio_ops = {
+	.set_value = stmfx_gpio_set,
+	.get_value = stmfx_gpio_get,
+	.get_function = stmfx_gpio_get_function,
+	.direction_input = stmfx_gpio_direction_input,
+	.direction_output = stmfx_gpio_direction_output,
+	.set_flags = stmfx_gpio_set_flags,
+	.get_flags = stmfx_gpio_get_flags,
+};
+
+U_BOOT_DRIVER(stmfx_gpio) = {
+	.name	= "stmfx-gpio",
+	.id	= UCLASS_GPIO,
+	.probe	= stmfx_gpio_probe,
+	.ops	= &stmfx_gpio_ops,
+};
+
+#if CONFIG_IS_ENABLED(PINCONF)
+static const struct pinconf_param stmfx_pinctrl_conf_params[] = {
+	{ "bias-disable", PIN_CONFIG_BIAS_DISABLE, 0 },
+	{ "bias-pull-up", PIN_CONFIG_BIAS_PULL_UP, 0 },
+	{ "bias-pull-pin-default", PIN_CONFIG_BIAS_PULL_PIN_DEFAULT, 0 },
+	{ "bias-pull-down", PIN_CONFIG_BIAS_PULL_DOWN, 0 },
+	{ "drive-open-drain", PIN_CONFIG_DRIVE_OPEN_DRAIN, 0 },
+	{ "drive-push-pull", PIN_CONFIG_DRIVE_PUSH_PULL, 0 },
+	{ "output-high", PIN_CONFIG_OUTPUT, 1 },
+	{ "output-low", PIN_CONFIG_OUTPUT, 0 },
+};
+
+static int stmfx_pinctrl_conf_set(struct udevice *dev, unsigned int pin,
+				  unsigned int param, unsigned int arg)
+{
+	int ret, dir;
+	struct stmfx_pinctrl *plat = dev_get_plat(dev);
+
+	dir = stmfx_gpio_get_function(plat->gpio, pin);
+
+	if (dir < 0)
+		return dir;
+
+	switch (param) {
+	case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
+	case PIN_CONFIG_BIAS_DISABLE:
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		ret = stmfx_conf_set_type(dev, pin, 0);
+		break;
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		ret = stmfx_conf_set_type(dev, pin, 1);
+		if (ret)
+			return ret;
+		ret = stmfx_conf_set_pupd(dev, pin, 0);
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		ret = stmfx_conf_set_type(dev, pin, 1);
+		if (ret)
+			return ret;
+		ret = stmfx_conf_set_pupd(dev, pin, 1);
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		ret = stmfx_conf_set_type(dev, pin, 1);
+		break;
+	case PIN_CONFIG_OUTPUT:
+		ret = stmfx_gpio_direction_output(plat->gpio, pin, arg);
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	return ret;
+}
+#endif
+
+static int stmfx_pinctrl_get_pins_count(struct udevice *dev)
+{
+	struct stmfx_pinctrl *plat = dev_get_plat(dev);
+	struct gpio_dev_priv *uc_priv;
+
+	uc_priv = dev_get_uclass_priv(plat->gpio);
+
+	return uc_priv->gpio_count;
+}
+
+/*
+ * STMFX pins[15:0] are called "gpio[15:0]"
+ * and STMFX pins[23:16] are called "agpio[7:0]"
+ */
+static char pin_name[PINNAME_SIZE];
+static const char *stmfx_pinctrl_get_pin_name(struct udevice *dev,
+					      unsigned int selector)
+{
+	if (selector < STMFX_MAX_GPIO)
+		snprintf(pin_name, PINNAME_SIZE, "gpio%u", selector);
+	else
+		snprintf(pin_name, PINNAME_SIZE, "agpio%u", selector - 16);
+	return pin_name;
+}
+
+static const char *stmfx_pinctrl_get_pin_conf(struct udevice *dev,
+					      unsigned int pin, int func)
+{
+	int pupd, type;
+
+	type = stmfx_conf_get_type(dev, pin);
+	if (type < 0)
+		return "";
+
+	if (func == GPIOF_OUTPUT) {
+		if (type)
+			return "drive-open-drain";
+		else
+			return ""; /* default: push-pull*/
+	}
+	if (!type)
+		return ""; /* default: bias-disable*/
+
+	pupd = stmfx_conf_get_pupd(dev, pin);
+	if (pupd < 0)
+		return "";
+
+	if (pupd)
+		return "bias-pull-up";
+	else
+		return "bias-pull-down";
+}
+
+static int stmfx_pinctrl_get_pin_muxing(struct udevice *dev,
+					unsigned int selector,
+					char *buf, int size)
+{
+	struct stmfx_pinctrl *plat = dev_get_plat(dev);
+	int func;
+
+	func = stmfx_gpio_get_function(plat->gpio, selector);
+	if (func < 0)
+		return func;
+
+	snprintf(buf, size, "%s ", func == GPIOF_INPUT ? "input" : "output");
+
+	strncat(buf, stmfx_pinctrl_get_pin_conf(dev, selector, func), size);
+
+	return 0;
+}
+
+static int stmfx_pinctrl_bind(struct udevice *dev)
+{
+	struct stmfx_pinctrl *plat = dev_get_plat(dev);
+
+	/* subnode name is not explicit: use father name */
+	device_set_name(dev, dev->parent->name);
+
+	return device_bind_driver_to_node(dev->parent,
+					  "stmfx-gpio", dev->parent->name,
+					  dev_ofnode(dev), &plat->gpio);
+};
+
+static int stmfx_pinctrl_probe(struct udevice *dev)
+{
+	struct stmfx_pinctrl *plat = dev_get_plat(dev);
+
+	return device_probe(plat->gpio);
+};
+
+const struct pinctrl_ops stmfx_pinctrl_ops = {
+	.get_pins_count = stmfx_pinctrl_get_pins_count,
+	.get_pin_name = stmfx_pinctrl_get_pin_name,
+	.set_state = pinctrl_generic_set_state,
+	.get_pin_muxing	= stmfx_pinctrl_get_pin_muxing,
+#if CONFIG_IS_ENABLED(PINCONF)
+	.pinconf_set = stmfx_pinctrl_conf_set,
+	.pinconf_num_params = ARRAY_SIZE(stmfx_pinctrl_conf_params),
+	.pinconf_params = stmfx_pinctrl_conf_params,
+#endif
+};
+
+static const struct udevice_id stmfx_pinctrl_match[] = {
+	{ .compatible = "st,stmfx-0300-pinctrl", },
+};
+
+U_BOOT_DRIVER(stmfx_pinctrl) = {
+	.name = "stmfx-pinctrl",
+	.id = UCLASS_PINCTRL,
+	.of_match = of_match_ptr(stmfx_pinctrl_match),
+	.bind = stmfx_pinctrl_bind,
+	.probe = stmfx_pinctrl_probe,
+	.ops = &stmfx_pinctrl_ops,
+	.plat_auto	= sizeof(struct stmfx_pinctrl),
+};
+
+static int stmfx_chip_init(struct udevice *dev)
+{
+	u8 id;
+	u8 version[2];
+	int ret;
+	struct dm_i2c_chip *chip = dev_get_parent_plat(dev);
+
+	ret = dm_i2c_reg_read(dev, STMFX_REG_CHIP_ID);
+	if (ret < 0) {
+		dev_err(dev, "error reading chip id: %d\n", ret);
+		return ret;
+	}
+	id = (u8)ret;
+	/*
+	 * Check that ID is the complement of the I2C address:
+	 * STMFX I2C address follows the 7-bit format (MSB), that's why
+	 * client->addr is shifted.
+	 *
+	 * STMFX_I2C_ADDR|       STMFX         |        Linux
+	 *   input pin   | I2C device address  | I2C device address
+	 *---------------------------------------------------------
+	 *       0       | b: 1000 010x h:0x84 |       0x42
+	 *       1       | b: 1000 011x h:0x86 |       0x43
+	 */
+	if (FIELD_GET(STMFX_REG_CHIP_ID_MASK, ~id) != (chip->chip_addr << 1)) {
+		dev_err(dev, "unknown chip id: %#x\n", id);
+		return -EINVAL;
+	}
+
+	ret = dm_i2c_read(dev, STMFX_REG_FW_VERSION_MSB,
+			  version, sizeof(version));
+	if (ret) {
+		dev_err(dev, "error reading fw version: %d\n", ret);
+		return ret;
+	}
+
+	dev_info(dev, "STMFX id: %#x, fw version: %x.%02x\n",
+		 id, version[0], version[1]);
+
+	ret = dm_i2c_reg_read(dev, STMFX_REG_SYS_CTRL);
+
+	if (ret < 0)
+		return ret;
+
+	ret = dm_i2c_reg_write(dev, STMFX_REG_SYS_CTRL,
+			       ret | STMFX_REG_SYS_CTRL_SWRST);
+	if (ret)
+		return ret;
+
+	mdelay(STMFX_BOOT_TIME_MS);
+
+	return ret;
+}
+
+static int stmfx_probe(struct udevice *dev)
+{
+	struct udevice *vdd;
+	int ret;
+
+	ret = device_get_supply_regulator(dev, "vdd-supply", &vdd);
+	if (ret && ret != -ENOENT) {
+		dev_err(dev, "vdd regulator error:%d\n", ret);
+		return ret;
+	}
+	if (!ret) {
+		ret = regulator_set_enable(vdd, true);
+		if (ret) {
+			dev_err(dev, "vdd enable failed: %d\n", ret);
+			return ret;
+		}
+	}
+
+	return stmfx_chip_init(dev);
+}
+
+static const struct udevice_id stmfx_match[] = {
+	{ .compatible = "st,stmfx-0300", },
+};
+
+U_BOOT_DRIVER(stmfx) = {
+	.name = "stmfx",
+	.id = UCLASS_I2C_GENERIC,
+	.of_match = of_match_ptr(stmfx_match),
+	.probe = stmfx_probe,
+	.bind = dm_scan_fdt_dev,
+};