diff options
Diffstat (limited to 'docs/getting-started/machines/renesas.md')
| -rw-r--r-- | docs/getting-started/machines/renesas.md | 127 |
1 files changed, 72 insertions, 55 deletions
diff --git a/docs/getting-started/machines/renesas.md b/docs/getting-started/machines/renesas.md index 9f84acc..93e7cca 100644 --- a/docs/getting-started/machines/renesas.md +++ b/docs/getting-started/machines/renesas.md @@ -131,7 +131,8 @@ Follow these steps to download the drivers you need: | AGL Version| Renesas version | |:-:|:-:| | AGL master | 3.21.0 | - | AGL halibut 8.0.2 8.0.3 8.0.4 | 3.21.0 | + | AGL icefish 9.0.0 | 3.21.0 | + | AGL halibut 8.0.2 8.0.3 8.0.4 8.0.5 | 3.21.0 | | AGL halibut 8.0.1 | 3.19.0 | | AGL halibut 8.0.0 | 3.15.0 | | AGL guppy 7.0.4 | 3.21.0 | @@ -705,19 +706,20 @@ Hit any key to stop autoboot: 0 Follow these steps to configure the board to use the MicroSD card as the boot device and also to set the screen resolution: -1. As the board is powering up, press any key to stop the autoboot process. +<ol> + <li>As the board is powering up, press any key to stop the autoboot process. You need to press a key quickly as you have just a few seconds in which to press a key. + </li> -2. Once the autoboot process is interrupted, use the board's serial console to - enter **printenv** to check if you have correct parameters for booting your board: - - <details> - <summary> - Here is an example using the **h3ulcb** board: - </summary> - <pre> - <code> + <li>Once the autoboot process is interrupted, use the board's serial console to + enter <b>printenv</b> to check if you have correct parameters for booting your board: +<details> + <summary> + Here is an example using the <b>h3ulcb</b> board: + </summary> + <pre> + <code> => printenv baudrate=115200 @@ -734,15 +736,15 @@ stdout=serial ver=U-Boot 2015.04 (Jun 09 2016 - 19:21:52) Environment size: 648/131068 bytes - </code> - </pre> - </details> - <details> - <summary> - Here is a second example using the **m3ulcb** board: - </summary> - <pre> - <code> + </code> + </pre> +</details> +<details> + <summary> + Here is a second example using the <b>m3ulcb</b> board: + </summary> + <pre> + <code> => printenv baudrate=115200 bootargs=console=ttySC0,115200 root=/dev/mmcblk1p1 rootwait ro rootfstype=ext4 @@ -759,63 +761,77 @@ stdout=serial ver=U-Boot 2015.04 (Nov 30 2016 - 18:25:18) Environment size: 557/131068 bytes - </code> - </pre> - </details> + </code> + </pre> +</details> + </li> -3. To boot your board using the MicroSD card, be sure your environment is set up + <li>To boot your board using the MicroSD card, be sure your environment is set up as follows: - ``` + <pre> + <code> setenv bootargs console=ttySC0,115200 ignore_loglevel vmalloc=384M video=HDMI-A-1:1920x1080-32@60 root=/dev/mmcblk1p1 rw rootfstype=ext4 rootwait rootdelay=2 setenv bootcmd run load_ker\; run load_dtb\; booti 0x48080000 - 0x48000000 setenv load_ker ext4load mmc 0:1 0x48080000 /boot/Image - ``` + </code> + </pre> + </li> -4. Depending on the board type, the BSP version, and the existence of - a Kingfisher board, make sure your ``load_dtb`` is set as follows: + <li>Depending on the board type, the BSP version, and the existence of + a Kingfisher board, make sure your ``load_dtb`` is set as follows:<br> - **h3ulcb with BSP version greater than or equal to 2.19**: + <b>h3ulcb with BSP version greater than or equal to 2.19</b>: - ``` + <pre> + <code> setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7795-es1-h3ulcb.dtb - ``` + </code> + </pre> - **h3ulcb with BSP version less than 2.19**: + <b>h3ulcb with BSP version less than 2.19</b>: - ``` + <pre> + <code> setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7795-h3ulcb.dtb - ``` - - **m3ulcb**: + </code> + </pre> - ```bash + <b>m3ulcb</b>: + <pre> + <code> setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb.dtb - ``` - - **m3ulcb with a Kingfisher board**: + </code> + </pre> - ```bash + <b>m3ulcb with a Kingfisher board</b>: + <pre> + <code> setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7796-m3ulcb-kf.dtb - ``` - - **h3ulcb with a Kingfisher board**: + </code> + </pre> - ```bash + <b>h3ulcb with a Kingfisher board</b>: + <pre> + <code> setenv load_dtb ext4load mmc 0:1 0x48000000 /boot/r8a7795-es1-h3ulcb-kf.dtb - ``` - -5. Save the boot environment: + </code> + </pre> + </li> - ```bash - saveenv - ``` + <li>Save the boot environment:<br> + <code> + saveenv + </code> + </li> -6. Boot the board: + <li>Boot the board:<br> + <code> + run bootcmd + </code> + </li> +</ol> -``` -run bootcmd -``` ## 10. Troubleshooting ### Logging Into the Console @@ -892,3 +908,4 @@ you can determine the board's IP address and log in using `ssh`. </details> **NOTE:** More generics troubleshooting can be found here : [Generic issues](../troubleshooting.html) + git push --set-upstream origin guppy
\ No newline at end of file |