Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

12 files changed, 4212 insertions, 0 deletions

diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/Kconfig b/roms/u-boot/arch/arm/mach-omap2/omap5/Kconfig
new file mode 100644
index 000000000..4c2f990b2
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/Kconfig
@@ -0,0 +1,164 @@
+if OMAP54XX
+
+config DRA7XX
+	bool
+	help
+	  DRA7xx is an OMAP based SOC with Dual Core A-15s.
+
+choice
+	prompt "OMAP5 board select"
+	optional
+
+config TARGET_CM_T54
+	bool "CompuLab CM-T54"
+
+config TARGET_OMAP5_UEVM
+	bool "TI OMAP5 uEVM board"
+
+config TARGET_DRA7XX_EVM
+	bool "TI DRA7XX"
+	select BOARD_LATE_INIT
+	select DRA7XX
+	select PHYS_64BIT
+	select TI_I2C_BOARD_DETECT
+	imply DM_PMIC
+	imply DM_REGULATOR
+	imply DM_REGULATOR_LP87565
+	imply DM_THERMAL
+	imply PMIC_LP87565
+	imply SCSI
+	imply SPL_THERMAL
+	imply TI_DRA7_THERMAL
+
+config TARGET_AM57XX_EVM
+	bool "AM57XX"
+	select BOARD_LATE_INIT
+	select CMD_DDR3
+	select DRA7XX
+	select TI_I2C_BOARD_DETECT
+	select SUPPORT_EXTENSION_SCAN
+	imply DM_THERMAL
+	imply SCSI
+	imply SPL_THERMAL
+	imply TI_DRA7_THERMAL
+
+endchoice
+
+config SYS_SOC
+	default "omap5"
+
+config OMAP_PLATFORM_RESET_TIME_MAX_USEC
+	int "Something"
+	range 0  31219
+	default 31219
+	help
+	  Most OMAPs' provide a way to specify the time for which the reset
+	  should be held low while the voltages and Oscillator outputs
+	  stabilize.
+	  This time is mostly board and PMIC dependent. Hence the boards are
+	  expected to specify a pre-computed time using the above option.
+	  This value can be computed using a summation of the below 3
+	  parameters
+	  1: Time taken by the Osciallator to stop and restart
+	  2: PMIC OTP time
+	  3: Voltage ramp time, which can be derived using the PMIC slew rate
+	     and value of voltage ramp needed.
+
+if TARGET_DRA7XX_EVM || TARGET_AM57XX_EVM
+menu "Voltage Domain OPP selections"
+
+choice
+	prompt "MPU Voltage Domain"
+	default DRA7_MPU_OPP_NOM
+        help
+	  Select the Operating Performance Point(OPP) for the MPU voltage
+	  domain on DRA7xx & AM57xx SoCs.
+
+config DRA7_MPU_OPP_NOM
+	bool "OPP NOM"
+	help
+	  This config option enables Normal OPP for MPU. This is the safest
+	  option for booting.
+
+endchoice
+
+choice
+	prompt "DSPEVE Voltage Domain"
+        help
+	  Select the Operating Performance Point(OPP) for the DSPEVE voltage
+	  domain on DRA7xx & AM57xx SoCs.
+
+config DRA7_DSPEVE_OPP_NOM
+	bool "OPP NOM"
+	help
+	  This config option enables Normal OPP for DSPEVE. This is the safest
+	  option for booting and choose this when unsure about other OPPs .
+
+config DRA7_DSPEVE_OPP_OD
+	bool "OPP OD"
+	help
+	  This config option enables Over drive OPP for DSPEVE.
+
+config DRA7_DSPEVE_OPP_HIGH
+	bool "OPP HIGH"
+	help
+	  This config option enables High OPP for DSPEVE.
+
+endchoice
+
+choice
+	prompt "IVA Voltage Domain"
+        help
+	  Select the Operating Performance Point(OPP) for the IVA voltage
+	  domain on DRA7xx & AM57xx SoCs.
+
+config DRA7_IVA_OPP_NOM
+	bool "OPP NOM"
+	help
+	  This config option enables Normal OPP for IVA. This is the safest
+	  option for booting and choose this when unsure about other OPPs .
+
+config DRA7_IVA_OPP_OD
+	bool "OPP OD"
+	help
+	  This config option enables Over drive OPP for IVA.
+
+config DRA7_IVA_OPP_HIGH
+	bool "OPP HIGH"
+	help
+	  This config option enables High OPP for IVA.
+
+endchoice
+
+choice
+	prompt "GPU Voltage Domain"
+        help
+	  Select the Operating Performance Point(OPP) for the GPU voltage
+	  domain on DRA7xx & AM57xx SoCs.
+
+config DRA7_GPU_OPP_NOM
+	bool "OPP NOM"
+	help
+	  This config option enables Normal OPP for GPU. This is the safest
+	  option for booting and choose this when unsure about other OPPs .
+
+config DRA7_GPU_OPP_OD
+	bool "OPP OD"
+	help
+	  This config option enables Over drive OPP for GPU.
+
+config DRA7_GPU_OPP_HIGH
+	bool "OPP HIGH"
+	help
+	  This config option enables High OPP for GPU.
+
+endchoice
+
+endmenu
+endif
+
+source "board/ti/omap5_uevm/Kconfig"
+source "board/ti/dra7xx/Kconfig"
+source "board/ti/am57xx/Kconfig"
+
+endif
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/Makefile b/roms/u-boot/arch/arm/mach-omap2/omap5/Makefile
new file mode 100644
index 000000000..592e026ed
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/Makefile
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2000-2010
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+
+obj-y	+= boot.o
+obj-y	+= hwinit.o
+obj-y	+= emif.o
+obj-y	+= sdram.o
+obj-y	+= prcm-regs.o
+obj-y	+= hw_data.o
+obj-y	+= abb.o
+obj-y	+= fdt.o
+obj-$(CONFIG_IODELAY_RECALIBRATION) += dra7xx_iodelay.o
+obj-$(CONFIG_DRA7XX) += sec_entry_cpu1.o
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/abb.c b/roms/u-boot/arch/arm/mach-omap2/omap5/abb.c
new file mode 100644
index 000000000..2f9f8e65d
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/abb.c
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Adaptive Body Bias programming sequence for OMAP5 family
+ *
+ * (C) Copyright 2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
+ */
+
+#include <common.h>
+#include <asm/omap_common.h>
+#include <asm/io.h>
+#include <linux/bitops.h>
+
+/*
+ * Setup LDOVBB for OMAP5.
+ * On OMAP5+ some ABB settings are fused. They are handled
+ * in the following way:
+ *
+ * 1. corresponding EFUSE register contains ABB enable bit
+ *    and VSET value
+ * 2. If ABB enable bit is set to 1, than ABB should be
+ *    enabled, otherwise ABB should be disabled
+ * 3. If ABB is enabled, than VSET value should be copied
+ *    to corresponding MUX control register
+ */
+s8 abb_setup_ldovbb(u32 fuse, u32 ldovbb)
+{
+	u32 vset;
+	u32 fuse_enable_mask = OMAP5_PROD_ABB_FUSE_ENABLE_MASK;
+	u32 fuse_vset_mask = OMAP5_PROD_ABB_FUSE_VSET_MASK;
+
+	if (!is_omap54xx()) {
+		/* DRA7 */
+		fuse_enable_mask = DRA7_ABB_FUSE_ENABLE_MASK;
+		fuse_vset_mask = DRA7_ABB_FUSE_VSET_MASK;
+	}
+	/*
+	 * ABB parameters must be properly fused
+	 * otherwise ABB should be disabled
+	 */
+	vset = readl(fuse);
+	if (!(vset & fuse_enable_mask))
+		return -1;
+
+	/* prepare VSET value for LDOVBB mux register */
+	vset &= fuse_vset_mask;
+	vset >>= ffs(fuse_vset_mask) - 1;
+	vset <<= ffs(OMAP5_ABB_LDOVBBMPU_VSET_OUT_MASK) - 1;
+	vset |= OMAP5_ABB_LDOVBBMPU_MUX_CTRL_MASK;
+
+	/* setup LDOVBB using fused value */
+	clrsetbits_le32(ldovbb,  OMAP5_ABB_LDOVBBMPU_VSET_OUT_MASK, vset);
+
+	return 0;
+}
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/boot.c b/roms/u-boot/arch/arm/mach-omap2/omap5/boot.c
new file mode 100644
index 000000000..15d6836c6
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/boot.c
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * OMAP5 boot
+ *
+ * Copyright (C) 2015 Paul Kocialkowski <contact@paulk.fr>
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/omap_common.h>
+#include <spl.h>
+
+static u32 boot_devices[] = {
+#if defined(CONFIG_DRA7XX)
+	BOOT_DEVICE_MMC2,
+	BOOT_DEVICE_NAND,
+	BOOT_DEVICE_MMC1,
+	BOOT_DEVICE_SATA,
+	BOOT_DEVICE_XIP,
+	BOOT_DEVICE_XIP,
+	BOOT_DEVICE_SPI,
+	BOOT_DEVICE_SPI,
+#else
+	BOOT_DEVICE_MMC2,
+	BOOT_DEVICE_NAND,
+	BOOT_DEVICE_MMC1,
+	BOOT_DEVICE_SATA,
+	BOOT_DEVICE_XIP,
+	BOOT_DEVICE_MMC2,
+	BOOT_DEVICE_XIPWAIT,
+#endif
+};
+
+u32 omap_sys_boot_device(void)
+{
+	u32 sys_boot;
+
+	/* Grab the first 4 bits of the status register for SYS_BOOT. */
+	sys_boot = readl((u32 *) (*ctrl)->control_status) & ((1 << 4) - 1);
+
+	if (sys_boot >= (sizeof(boot_devices) / sizeof(u32)))
+		return BOOT_DEVICE_NONE;
+
+	return boot_devices[sys_boot];
+}
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/dra7xx_iodelay.c b/roms/u-boot/arch/arm/mach-omap2/omap5/dra7xx_iodelay.c
new file mode 100644
index 000000000..8569eff31
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/dra7xx_iodelay.c
@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2015
+ * Texas Instruments Incorporated, <www.ti.com>
+ *
+ * Lokesh Vutla <lokeshvutla@ti.com>
+ */
+
+#include <common.h>
+#include <hang.h>
+#include <log.h>
+#include <asm/utils.h>
+#include <asm/arch/dra7xx_iodelay.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/mux_dra7xx.h>
+#include <asm/omap_common.h>
+
+static int isolate_io(u32 isolate)
+{
+	if (isolate) {
+		clrsetbits_le32((*ctrl)->control_pbias, SDCARD_PWRDNZ,
+				SDCARD_PWRDNZ);
+		clrsetbits_le32((*ctrl)->control_pbias, SDCARD_BIAS_PWRDNZ,
+				SDCARD_BIAS_PWRDNZ);
+	}
+
+	/* Override control on ISOCLKIN signal to IO pad ring. */
+	clrsetbits_le32((*prcm)->prm_io_pmctrl, PMCTRL_ISOCLK_OVERRIDE_MASK,
+			PMCTRL_ISOCLK_OVERRIDE_CTRL);
+	if (!wait_on_value(PMCTRL_ISOCLK_STATUS_MASK, PMCTRL_ISOCLK_STATUS_MASK,
+			   (u32 *)(*prcm)->prm_io_pmctrl, LDELAY))
+		return ERR_DEISOLATE_IO << isolate;
+
+	/* Isolate/Deisolate IO */
+	clrsetbits_le32((*ctrl)->ctrl_core_sma_sw_0, CTRL_ISOLATE_MASK,
+			isolate << CTRL_ISOLATE_SHIFT);
+	/* Dummy read to add delay t > 10ns */
+	readl((*ctrl)->ctrl_core_sma_sw_0);
+
+	/* Return control on ISOCLKIN to hardware */
+	clrsetbits_le32((*prcm)->prm_io_pmctrl, PMCTRL_ISOCLK_OVERRIDE_MASK,
+			PMCTRL_ISOCLK_NOT_OVERRIDE_CTRL);
+	if (!wait_on_value(PMCTRL_ISOCLK_STATUS_MASK,
+			   0 << PMCTRL_ISOCLK_STATUS_SHIFT,
+			   (u32 *)(*prcm)->prm_io_pmctrl, LDELAY))
+		return ERR_DEISOLATE_IO << isolate;
+
+	return 0;
+}
+
+static int calibrate_iodelay(u32 base)
+{
+	u32 reg;
+
+	/* Configure REFCLK period */
+	reg = readl(base + CFG_REG_2_OFFSET);
+	reg &= ~CFG_REG_REFCLK_PERIOD_MASK;
+	reg |= CFG_REG_REFCLK_PERIOD;
+	writel(reg, base + CFG_REG_2_OFFSET);
+
+	/* Initiate Calibration */
+	clrsetbits_le32(base + CFG_REG_0_OFFSET, CFG_REG_CALIB_STRT_MASK,
+			CFG_REG_CALIB_STRT << CFG_REG_CALIB_STRT_SHIFT);
+	if (!wait_on_value(CFG_REG_CALIB_STRT_MASK, CFG_REG_CALIB_END,
+			   (u32 *)(base + CFG_REG_0_OFFSET), LDELAY))
+		return ERR_CALIBRATE_IODELAY;
+
+	return 0;
+}
+
+static int update_delay_mechanism(u32 base)
+{
+	/* Initiate the reload of calibrated values. */
+	clrsetbits_le32(base + CFG_REG_0_OFFSET, CFG_REG_ROM_READ_MASK,
+			CFG_REG_ROM_READ_START);
+	if (!wait_on_value(CFG_REG_ROM_READ_MASK, CFG_REG_ROM_READ_END,
+			   (u32 *)(base + CFG_REG_0_OFFSET), LDELAY))
+		return ERR_UPDATE_DELAY;
+
+	return 0;
+}
+
+static u32 calculate_delay(u32 base, u16 offset, u16 den)
+{
+	u16 refclk_period, dly_cnt, ref_cnt;
+	u32 reg, q, r;
+
+	refclk_period = readl(base + CFG_REG_2_OFFSET) &
+			      CFG_REG_REFCLK_PERIOD_MASK;
+
+	reg = readl(base + offset);
+	dly_cnt = (reg & CFG_REG_DLY_CNT_MASK) >> CFG_REG_DLY_CNT_SHIFT;
+	ref_cnt = (reg & CFG_REG_REF_CNT_MASK) >> CFG_REG_REF_CNT_SHIFT;
+
+	if (!dly_cnt || !den)
+		return 0;
+
+	/*
+	 * To avoid overflow and integer truncation, delay value
+	 * is calculated as quotient + remainder.
+	 */
+	q = 5 * ((ref_cnt * refclk_period) / (dly_cnt * den));
+	r = (10 * ((ref_cnt * refclk_period) % (dly_cnt * den))) /
+		(2 * dly_cnt * den);
+
+	return q + r;
+}
+
+static u32 get_cfg_reg(u16 a_delay, u16 g_delay, u32 cpde, u32 fpde)
+{
+	u32 g_delay_coarse, g_delay_fine;
+	u32 a_delay_coarse, a_delay_fine;
+	u32 c_elements, f_elements;
+	u32 total_delay, reg = 0;
+
+	g_delay_coarse = g_delay / 920;
+	g_delay_fine = ((g_delay % 920) * 10) / 60;
+
+	a_delay_coarse = a_delay / cpde;
+	a_delay_fine = ((a_delay % cpde) * 10) / fpde;
+
+	c_elements = g_delay_coarse + a_delay_coarse;
+	f_elements = (g_delay_fine + a_delay_fine) / 10;
+
+	if (f_elements > 22) {
+		total_delay = c_elements * cpde + f_elements * fpde;
+
+		c_elements = total_delay / cpde;
+		f_elements = (total_delay % cpde) / fpde;
+	}
+
+	reg = (c_elements << CFG_X_COARSE_DLY_SHIFT) & CFG_X_COARSE_DLY_MASK;
+	reg |= (f_elements << CFG_X_FINE_DLY_SHIFT) & CFG_X_FINE_DLY_MASK;
+	reg |= CFG_X_SIGNATURE << CFG_X_SIGNATURE_SHIFT;
+	reg |= CFG_X_LOCK << CFG_X_LOCK_SHIFT;
+
+	return reg;
+}
+
+int do_set_iodelay(u32 base, struct iodelay_cfg_entry const *array,
+		   int niodelays)
+{
+	struct iodelay_cfg_entry *iodelay = (struct iodelay_cfg_entry *)array;
+	u32 reg, cpde, fpde, i;
+
+	if (!niodelays)
+		return 0;
+
+	cpde = calculate_delay((*ctrl)->iodelay_config_base, CFG_REG_3_OFFSET,
+			       88);
+	if (!cpde)
+		return ERR_CPDE;
+
+	fpde = calculate_delay((*ctrl)->iodelay_config_base, CFG_REG_4_OFFSET,
+			       264);
+	if (!fpde)
+		return ERR_FPDE;
+
+	for (i = 0; i < niodelays; i++, iodelay++) {
+		reg = get_cfg_reg(iodelay->a_delay, iodelay->g_delay, cpde,
+				  fpde);
+		writel(reg, base + iodelay->offset);
+	}
+
+	return 0;
+}
+
+int __recalibrate_iodelay_start(void)
+{
+	int ret = 0;
+
+	/* IO recalibration should be done only from SRAM */
+	if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context()) {
+		puts("IODELAY recalibration called from invalid context - use only from SPL in SRAM\n");
+		return -1;
+	}
+
+	/* unlock IODELAY CONFIG registers */
+	writel(CFG_IODELAY_UNLOCK_KEY, (*ctrl)->iodelay_config_base +
+	       CFG_REG_8_OFFSET);
+
+	ret = calibrate_iodelay((*ctrl)->iodelay_config_base);
+	if (ret)
+		goto err;
+
+	ret = isolate_io(ISOLATE_IO);
+	if (ret)
+		goto err;
+
+	ret = update_delay_mechanism((*ctrl)->iodelay_config_base);
+
+err:
+	return ret;
+}
+
+void __recalibrate_iodelay_end(int ret)
+{
+
+	/* IO recalibration should be done only from SRAM */
+	if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context()) {
+		puts("IODELAY recalibration called from invalid context - use only from SPL in SRAM\n");
+		return;
+	}
+
+	/* Deisolate IO if it is already isolated */
+	if (readl((*ctrl)->ctrl_core_sma_sw_0) & CTRL_ISOLATE_MASK)
+		isolate_io(DEISOLATE_IO);
+
+	/* lock IODELAY CONFIG registers */
+	writel(CFG_IODELAY_LOCK_KEY, (*ctrl)->iodelay_config_base +
+	       CFG_REG_8_OFFSET);
+
+	/*
+	 * UART cannot be used during IO recalibration sequence as IOs are in
+	 * isolation. So error handling and debug prints are done after
+	 * complete IO delay recalibration sequence
+	 */
+	switch (ret) {
+	case ERR_CALIBRATE_IODELAY:
+		puts("IODELAY: IO delay calibration sequence failed\n");
+		break;
+	case ERR_ISOLATE_IO:
+		puts("IODELAY: Isolation of Device IOs failed\n");
+		break;
+	case ERR_UPDATE_DELAY:
+		puts("IODELAY: Delay mechanism update with new calibrated values failed\n");
+		break;
+	case ERR_DEISOLATE_IO:
+		puts("IODELAY: De-isolation of Device IOs failed\n");
+		break;
+	case ERR_CPDE:
+		puts("IODELAY: CPDE calculation failed\n");
+		break;
+	case ERR_FPDE:
+		puts("IODELAY: FPDE calculation failed\n");
+		break;
+	case -1:
+		puts("IODELAY: Wrong Context call?\n");
+		break;
+	default:
+		debug("IODELAY: IO delay recalibration successfully completed\n");
+	}
+
+	/* If there is an error during iodelay recalibration, SoC is in a bad
+	 * state. Do not progress any further.
+	 */
+	if (ret)
+		hang();
+
+	return;
+}
+
+void __recalibrate_iodelay(struct pad_conf_entry const *pad, int npads,
+			   struct iodelay_cfg_entry const *iodelay,
+			   int niodelays)
+{
+	int ret = 0;
+
+	/* IO recalibration should be done only from SRAM */
+	if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context()) {
+		puts("IODELAY recalibration called from invalid context - use only from SPL in SRAM\n");
+		return;
+	}
+
+	ret = __recalibrate_iodelay_start();
+	if (ret)
+		goto err;
+
+	/* Configure Mux settings */
+	do_set_mux32((*ctrl)->control_padconf_core_base, pad, npads);
+
+	/* Configure Manual IO timing modes */
+	ret = do_set_iodelay((*ctrl)->iodelay_config_base, iodelay, niodelays);
+	if (ret)
+		goto err;
+
+err:
+	__recalibrate_iodelay_end(ret);
+
+}
+
+void late_recalibrate_iodelay(struct pad_conf_entry const *pad, int npads,
+			      struct iodelay_cfg_entry const *iodelay,
+			      int niodelays)
+{
+	int ret = 0;
+
+	/* unlock IODELAY CONFIG registers */
+	writel(CFG_IODELAY_UNLOCK_KEY, (*ctrl)->iodelay_config_base +
+	       CFG_REG_8_OFFSET);
+
+	ret = calibrate_iodelay((*ctrl)->iodelay_config_base);
+	if (ret)
+		goto err;
+
+	ret = update_delay_mechanism((*ctrl)->iodelay_config_base);
+
+	/* Configure Mux settings */
+	do_set_mux32((*ctrl)->control_padconf_core_base, pad, npads);
+
+	/* Configure Manual IO timing modes */
+	ret = do_set_iodelay((*ctrl)->iodelay_config_base, iodelay, niodelays);
+	if (ret)
+		goto err;
+
+err:
+	/* lock IODELAY CONFIG registers */
+	writel(CFG_IODELAY_LOCK_KEY, (*ctrl)->iodelay_config_base +
+	       CFG_REG_8_OFFSET);
+}
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/emif.c b/roms/u-boot/arch/arm/mach-omap2/omap5/emif.c
new file mode 100644
index 000000000..2de36b6fe
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/emif.c
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * EMIF programming
+ *
+ * (C) Copyright 2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * Aneesh V <aneesh@ti.com> for OMAP4
+ */
+
+#include <common.h>
+#include <log.h>
+#include <asm/emif.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/utils.h>
+
+#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
+#define print_timing_reg(reg) debug(#reg" - 0x%08x\n", (reg))
+static u32 *const T_num = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_NUM;
+static u32 *const T_den = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_DEN;
+#endif
+
+#ifdef CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
+/* Base AC Timing values specified by JESD209-2 for 532MHz operation */
+static const struct lpddr2_ac_timings timings_jedec_532_mhz = {
+	.max_freq = 532000000,
+	.RL = 8,
+	.tRPab = 21,
+	.tRCD = 18,
+	.tWR = 15,
+	.tRASmin = 42,
+	.tRRD = 10,
+	.tWTRx2 = 15,
+	.tXSR = 140,
+	.tXPx2 = 15,
+	.tRFCab = 130,
+	.tRTPx2 = 15,
+	.tCKE = 3,
+	.tCKESR = 15,
+	.tZQCS = 90,
+	.tZQCL = 360,
+	.tZQINIT = 1000,
+	.tDQSCKMAXx2 = 11,
+	.tRASmax = 70,
+	.tFAW = 50
+};
+
+/*
+ * Min tCK values specified by JESD209-2
+ * Min tCK specifies the minimum duration of some AC timing parameters in terms
+ * of the number of cycles. If the calculated number of cycles based on the
+ * absolute time value is less than the min tCK value, min tCK value should
+ * be used instead. This typically happens at low frequencies.
+ */
+static const struct lpddr2_min_tck min_tck_jedec = {
+	.tRL = 3,
+	.tRP_AB = 3,
+	.tRCD = 3,
+	.tWR = 3,
+	.tRAS_MIN = 3,
+	.tRRD = 2,
+	.tWTR = 2,
+	.tXP = 2,
+	.tRTP = 2,
+	.tCKE = 3,
+	.tCKESR = 3,
+	.tFAW = 8
+};
+
+static const struct lpddr2_ac_timings const*
+			jedec_ac_timings[MAX_NUM_SPEEDBINS] = {
+	&timings_jedec_532_mhz
+};
+
+static const struct lpddr2_device_timings jedec_default_timings = {
+	.ac_timings = jedec_ac_timings,
+	.min_tck = &min_tck_jedec
+};
+
+void emif_get_device_timings(u32 emif_nr,
+		const struct lpddr2_device_timings **cs0_device_timings,
+		const struct lpddr2_device_timings **cs1_device_timings)
+{
+	/* Assume Identical devices on EMIF1 & EMIF2 */
+	*cs0_device_timings = &jedec_default_timings;
+	*cs1_device_timings = NULL;
+}
+#endif /* CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS */
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/fdt.c b/roms/u-boot/arch/arm/mach-omap2/omap5/fdt.c
new file mode 100644
index 000000000..c4162420f
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/fdt.c
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2016 Texas Instruments, Inc.
+ */
+
+#include <common.h>
+#include <hang.h>
+#include <log.h>
+#include <linux/libfdt.h>
+#include <fdt_support.h>
+#include <malloc.h>
+
+#include <asm/omap_common.h>
+#include <asm/arch-omap5/sys_proto.h>
+
+#ifdef CONFIG_TI_SECURE_DEVICE
+
+/* Give zero values if not already defined */
+#ifndef TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ
+#define TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ (0)
+#endif
+#ifndef CONFIG_SECURE_RUNTIME_RESV_SRAM_SZ
+#define CONFIG_SECURE_RUNTIME_RESV_SRAM_SZ (0)
+#endif
+
+static u32 hs_irq_skip[] = {
+	8,	/* Secure violation reporting interrupt */
+	15,	/* One interrupt for SDMA by secure world */
+	118	/* One interrupt for Crypto DMA by secure world */
+};
+
+static int ft_hs_fixup_crossbar(void *fdt, struct bd_info *bd)
+{
+	const char *path;
+	int offs;
+	int ret;
+	int len, i, old_cnt, new_cnt;
+	u32 *temp;
+	const u32 *p_data;
+
+	/*
+	 * Increase the size of the fdt
+	 * so we have some breathing room
+	 */
+	ret = fdt_increase_size(fdt, 512);
+	if (ret < 0) {
+		printf("Could not increase size of device tree: %s\n",
+		       fdt_strerror(ret));
+		return ret;
+	}
+
+	/* Reserve IRQs that are used/needed by secure world */
+	path = "/ocp/crossbar";
+	offs = fdt_path_offset(fdt, path);
+	if (offs < 0) {
+		debug("Node %s not found.\n", path);
+		return 0;
+	}
+
+	/* Get current entries */
+	p_data = fdt_getprop(fdt, offs, "ti,irqs-skip", &len);
+	if (p_data)
+		old_cnt = len / sizeof(u32);
+	else
+		old_cnt = 0;
+
+	new_cnt = sizeof(hs_irq_skip) /
+				sizeof(hs_irq_skip[0]);
+
+	/* Create new/updated skip list for HS parts */
+	temp = malloc(sizeof(u32) * (old_cnt + new_cnt));
+	for (i = 0; i < new_cnt; i++)
+		temp[i] = cpu_to_fdt32(hs_irq_skip[i]);
+	for (i = 0; i < old_cnt; i++)
+		temp[i + new_cnt] = p_data[i];
+
+	/* Blow away old data and set new data */
+	fdt_delprop(fdt, offs, "ti,irqs-skip");
+	ret = fdt_setprop(fdt, offs, "ti,irqs-skip",
+			  temp,
+			  (old_cnt + new_cnt) * sizeof(u32));
+	free(temp);
+
+	/* Check if the update worked */
+	if (ret < 0) {
+		printf("Could not add ti,irqs-skip property to node %s: %s\n",
+		       path, fdt_strerror(ret));
+		return ret;
+	}
+
+	return 0;
+}
+
+#if ((TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ != 0) || \
+    (CONFIG_SECURE_RUNTIME_RESV_SRAM_SZ != 0))
+static int ft_hs_fixup_sram(void *fdt, struct bd_info *bd)
+{
+	const char *path;
+	int offs;
+	int ret;
+	u32 temp[2];
+
+	/*
+	 * Update SRAM reservations on secure devices. The OCMC RAM
+	 * is always reserved for secure use from the start of that
+	 * memory region
+	 */
+	path = "/ocp/ocmcram@40300000/sram-hs";
+	offs = fdt_path_offset(fdt, path);
+	if (offs < 0) {
+		debug("Node %s not found.\n", path);
+		return 0;
+	}
+
+	/* relative start offset */
+	temp[0] = cpu_to_fdt32(0);
+	/* reservation size */
+	temp[1] = cpu_to_fdt32(max(TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ,
+				   CONFIG_SECURE_RUNTIME_RESV_SRAM_SZ));
+	fdt_delprop(fdt, offs, "reg");
+	ret = fdt_setprop(fdt, offs, "reg", temp, 2 * sizeof(u32));
+	if (ret < 0) {
+		printf("Could not add reg property to node %s: %s\n",
+		       path, fdt_strerror(ret));
+		return ret;
+	}
+
+	return 0;
+}
+#else
+static int ft_hs_fixup_sram(void *fdt, struct bd_info *bd) { return 0; }
+#endif
+
+static void ft_hs_fixups(void *fdt, struct bd_info *bd)
+{
+	/* Check we are running on an HS/EMU device type */
+	if (GP_DEVICE != get_device_type()) {
+		if ((ft_hs_fixup_crossbar(fdt, bd) == 0) &&
+		    (ft_hs_disable_rng(fdt, bd) == 0) &&
+		    (ft_hs_fixup_sram(fdt, bd) == 0) &&
+		    (ft_hs_fixup_dram(fdt, bd) == 0) &&
+		    (ft_hs_add_tee(fdt, bd) == 0))
+			return;
+	} else {
+		printf("ERROR: Incorrect device type (GP) detected!");
+	}
+	/* Fixup failed or wrong device type */
+	hang();
+}
+#else
+static void ft_hs_fixups(void *fdt, struct bd_info *bd)
+{
+}
+#endif /* #ifdef CONFIG_TI_SECURE_DEVICE */
+
+#if defined(CONFIG_TARGET_DRA7XX_EVM) || defined(CONFIG_TARGET_AM57XX_EVM)
+#define OPP_DSP_CLK_NUM	3
+#define OPP_IVA_CLK_NUM	2
+#define OPP_GPU_CLK_NUM	2
+
+const char *dra7_opp_dsp_clk_names[OPP_DSP_CLK_NUM] = {
+	"dpll_dsp_ck",
+	"dpll_dsp_m2_ck",
+	"dpll_dsp_m3x2_ck",
+};
+
+const char *dra7_opp_iva_clk_names[OPP_IVA_CLK_NUM] = {
+	"dpll_iva_ck",
+	"dpll_iva_m2_ck",
+};
+
+const char *dra7_opp_gpu_clk_names[OPP_GPU_CLK_NUM] = {
+	"dpll_gpu_ck",
+	"dpll_gpu_m2_ck",
+};
+
+/* DSPEVE voltage domain */
+u32 dra7_opp_dsp_clk_rates[NUM_OPPS][OPP_DSP_CLK_NUM] = {
+	{}, /*OPP_LOW */
+	{600000000, 600000000, 400000000}, /* OPP_NOM */
+	{700000000, 700000000, 466666667}, /* OPP_OD */
+	{750000000, 750000000, 500000000}, /* OPP_HIGH */
+};
+
+/* DSP clock rates on DRA76x ACD-package based SoCs */
+u32 dra76_opp_dsp_clk_rates[NUM_OPPS][OPP_DSP_CLK_NUM] = {
+	{}, /* OPP_LOW */
+	{600000000, 600000000, 400000000}, /* OPP_NOM */
+	{700000000, 700000000, 466666667}, /* OPP_OD */
+	{850000000, 850000000, 566666667}, /* OPP_HIGH */
+};
+
+/* IVA voltage domain */
+u32 dra7_opp_iva_clk_rates[NUM_OPPS][OPP_IVA_CLK_NUM] = {
+	{}, /* OPP_LOW */
+	{1165000000, 388333334}, /* OPP_NOM */
+	{860000000, 430000000}, /* OPP_OD */
+	{1064000000, 532000000}, /* OPP_HIGH */
+};
+
+/* GPU voltage domain */
+u32 dra7_opp_gpu_clk_rates[NUM_OPPS][OPP_GPU_CLK_NUM] = {
+	{}, /* OPP_LOW */
+	{1277000000, 425666667}, /* OPP_NOM */
+	{1000000000, 500000000}, /* OPP_OD */
+	{1064000000, 532000000}, /* OPP_HIGH */
+};
+
+static int ft_fixup_clocks(void *fdt, const char **names, u32 *rates, int num)
+{
+	int offs, node_offs, ret, i;
+	uint32_t phandle;
+
+	offs = fdt_path_offset(fdt, "/ocp/interconnect@4a000000/segment@0/target-module@5000/cm_core_aon@0/clocks");
+	if (offs < 0)
+		offs = fdt_path_offset(fdt, "/ocp/l4@4a000000/cm_core_aon@5000/clocks");
+	if (offs < 0) {
+		debug("Could not find cm_core_aon clocks node path offset : %s\n",
+		      fdt_strerror(offs));
+		return offs;
+	}
+
+	for (i = 0; i < num; i++) {
+		node_offs = fdt_subnode_offset(fdt, offs, names[i]);
+		if (node_offs < 0) {
+			debug("Could not find clock sub-node %s: %s\n",
+			      names[i], fdt_strerror(node_offs));
+			return offs;
+		}
+
+		phandle = fdt_get_phandle(fdt, node_offs);
+		if (!phandle) {
+			debug("Could not find phandle for clock %s\n",
+			      names[i]);
+			return -1;
+		}
+
+		ret = fdt_setprop_u32(fdt, node_offs, "assigned-clocks",
+				      phandle);
+		if (ret < 0) {
+			debug("Could not add assigned-clocks property to clock node %s: %s\n",
+			      names[i], fdt_strerror(ret));
+			return ret;
+		}
+
+		ret = fdt_setprop_u32(fdt, node_offs, "assigned-clock-rates",
+				      rates[i]);
+		if (ret < 0) {
+			debug("Could not add assigned-clock-rates property to clock node %s: %s\n",
+			      names[i], fdt_strerror(ret));
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static void ft_opp_clock_fixups(void *fdt, struct bd_info *bd)
+{
+	const char **clk_names;
+	u32 *clk_rates;
+	int ret;
+
+	if (!is_dra72x() && !is_dra7xx())
+		return;
+
+	/* fixup DSP clocks */
+	clk_names = dra7_opp_dsp_clk_names;
+	clk_rates = dra7_opp_dsp_clk_rates[get_voltrail_opp(VOLT_EVE)];
+	/* adjust for higher OPP_HIGH clock rate on DRA76xP/DRA77xP SoCs */
+	if (is_dra76x_acd())
+		clk_rates = dra76_opp_dsp_clk_rates[get_voltrail_opp(VOLT_EVE)];
+
+	ret = ft_fixup_clocks(fdt, clk_names, clk_rates, OPP_DSP_CLK_NUM);
+	if (ret) {
+		printf("ft_fixup_clocks failed for DSP voltage domain: %s\n",
+		       fdt_strerror(ret));
+		return;
+	}
+
+	/* fixup IVA clocks */
+	clk_names = dra7_opp_iva_clk_names;
+	clk_rates = dra7_opp_iva_clk_rates[get_voltrail_opp(VOLT_IVA)];
+	ret = ft_fixup_clocks(fdt, clk_names, clk_rates, OPP_IVA_CLK_NUM);
+	if (ret) {
+		printf("ft_fixup_clocks failed for IVA voltage domain: %s\n",
+		       fdt_strerror(ret));
+		return;
+	}
+
+	/* fixup GPU clocks */
+	clk_names = dra7_opp_gpu_clk_names;
+	clk_rates = dra7_opp_gpu_clk_rates[get_voltrail_opp(VOLT_GPU)];
+	ret = ft_fixup_clocks(fdt, clk_names, clk_rates, OPP_GPU_CLK_NUM);
+	if (ret) {
+		printf("ft_fixup_clocks failed for GPU voltage domain: %s\n",
+		       fdt_strerror(ret));
+		return;
+	}
+}
+#else
+static void ft_opp_clock_fixups(void *fdt, struct bd_info *bd) { }
+#endif /* CONFIG_TARGET_DRA7XX_EVM || CONFIG_TARGET_AM57XX_EVM */
+
+/*
+ * Place for general cpu/SoC FDT fixups. Board specific
+ * fixups should remain in the board files which is where
+ * this function should be called from.
+ */
+void ft_cpu_setup(void *fdt, struct bd_info *bd)
+{
+	ft_hs_fixups(fdt, bd);
+	ft_opp_clock_fixups(fdt, bd);
+}
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/hw_data.c b/roms/u-boot/arch/arm/mach-omap2/omap5/hw_data.c
new file mode 100644
index 000000000..fa4e27063
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/hw_data.c
@@ -0,0 +1,812 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *
+ * HW data initialization for OMAP5
+ *
+ * (C) Copyright 2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * Sricharan R <r.sricharan@ti.com>
+ */
+#include <common.h>
+#include <palmas.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/omap_common.h>
+#include <asm/arch/clock.h>
+#include <asm/omap_gpio.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+
+struct prcm_regs const **prcm =
+			(struct prcm_regs const **) OMAP_SRAM_SCRATCH_PRCM_PTR;
+struct dplls const **dplls_data =
+			(struct dplls const **) OMAP_SRAM_SCRATCH_DPLLS_PTR;
+struct vcores_data const **omap_vcores =
+		(struct vcores_data const **) OMAP_SRAM_SCRATCH_VCORES_PTR;
+struct omap_sys_ctrl_regs const **ctrl =
+	(struct omap_sys_ctrl_regs const **)OMAP_SRAM_SCRATCH_SYS_CTRL;
+
+/* OPP NOM FREQUENCY for ES1.0 */
+static const struct dpll_params mpu_dpll_params_800mhz[NUM_SYS_CLKS] = {
+	{200, 2, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 12 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 13 MHz   */
+	{1000, 20, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 16.8 MHz */
+	{375, 8, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 19.2 MHz */
+	{400, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{375, 17, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}	/* 38.4 MHz */
+};
+
+/* OPP NOM FREQUENCY for OMAP5 ES2.0, and DRA7 ES1.0 */
+static const struct dpll_params mpu_dpll_params_1ghz[NUM_SYS_CLKS] = {
+	{250, 2, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 12 MHz   */
+	{500, 9, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 20 MHz   */
+	{119, 1, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 16.8 MHz */
+	{625, 11, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 19.2 MHz */
+	{500, 12, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{625, 23, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 38.4 MHz */
+};
+
+static const struct dpll_params
+			core_dpll_params_2128mhz_ddr532[NUM_SYS_CLKS] = {
+	{266, 2, 2, 5, 8, 4, 62, 5, -1, 5, 7, -1},		/* 12 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 13 MHz   */
+	{443, 6, 2, 5, 8, 4, 62, 5, -1, 5, 7, -1},		/* 16.8 MHz */
+	{277, 4, 2, 5, 8, 4, 62, 5, -1, 5, 7, -1},		/* 19.2 MHz */
+	{368, 8, 2, 5, 8, 4, 62, 5, -1, 5, 7, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{277, 9, 2, 5, 8, 4, 62, 5, -1, 5, 7, -1}		/* 38.4 MHz */
+};
+
+static const struct dpll_params
+			core_dpll_params_2128mhz_ddr532_es2[NUM_SYS_CLKS] = {
+	{266, 2, 2, 5, 8, 4, 62, 63, 6, 5, 7, 6},		/* 12 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 13 MHz   */
+	{443, 6, 2, 5, 8, 4, 62, 63, 6, 5, 7, 6},		/* 16.8 MHz */
+	{277, 4, 2, 5, 8, 4, 62, 63, 6, 5, 7, 6},		/* 19.2 MHz */
+	{368, 8, 2, 5, 8, 4, 62, 63, 6, 5, 7, 6},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{277, 9, 2, 5, 8, 4, 62, 63, 6, 5, 7, 6}		/* 38.4 MHz */
+};
+
+static const struct dpll_params
+		core_dpll_params_2128mhz_dra7xx[NUM_SYS_CLKS] = {
+	{266, 2, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6},		/* 12 MHz   */
+	{266, 4, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6},		/* 20 MHz   */
+	{443, 6, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6},		/* 16.8 MHz */
+	{277, 4, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6},		/* 19.2 MHz */
+	{368, 8, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{277, 9, 2, 1, -1, 4, 62, 5, -1, 5, 4, 6},		/* 38.4 MHz */
+};
+
+static const struct dpll_params per_dpll_params_768mhz[NUM_SYS_CLKS] = {
+	{32, 0, 4, 3, 6, 4, -1, 2, -1, -1, -1, -1},		/* 12 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 13 MHz   */
+	{160, 6, 4, 3, 6, 4, -1, 2, -1, -1, -1, -1},		/* 16.8 MHz */
+	{20, 0, 4, 3, 6, 4, -1, 2, -1, -1, -1, -1},		/* 19.2 MHz */
+	{192, 12, 4, 3, 6, 4, -1, 2, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{10, 0, 4, 3, 6, 4, -1, 2, -1, -1, -1, -1}		/* 38.4 MHz */
+};
+
+static const struct dpll_params per_dpll_params_768mhz_es2[NUM_SYS_CLKS] = {
+	{32, 0, 4, 3, 3, 4, -1, 2, -1, -1, -1, -1},		/* 12 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 13 MHz   */
+	{160, 6, 4, 3, 3, 4, -1, 2, -1, -1, -1, -1},		/* 16.8 MHz */
+	{20, 0, 4, 3, 3, 4, -1, 2, -1, -1, -1, -1},		/* 19.2 MHz */
+	{192, 12, 4, 3, 3, 4, -1, 2, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{10, 0, 4, 3, 3, 4, -1, 2, -1, -1, -1, -1}		/* 38.4 MHz */
+};
+
+static const struct dpll_params per_dpll_params_768mhz_dra7xx[NUM_SYS_CLKS] = {
+	{32, 0, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 12 MHz   */
+	{96, 4, 4, 1, 3, 4, 10, 2, -1, -1, -1, -1},		/* 20 MHz   */
+	{160, 6, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 16.8 MHz */
+	{20, 0, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 19.2 MHz */
+	{192, 12, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{10, 0, 4, 1, 3, 4, 4, 2, -1, -1, -1, -1},		/* 38.4 MHz */
+};
+
+static const struct dpll_params per_dpll_params_768mhz_dra76x[NUM_SYS_CLKS] = {
+	{32, 0, 4, 1, 3, 4, 8, 2, -1, -1, -1, -1},		/* 12 MHz   */
+	{96, 4, 4, 1, 3, 4, 8, 2, -1, -1, -1, -1},		/* 20 MHz   */
+	{160, 6, 4, 1, 3, 4, 8, 2, -1, -1, -1, -1},		/* 16.8 MHz */
+	{20, 0, 4, 1, 3, 4, 8, 2, -1, -1, -1, -1},		/* 19.2 MHz */
+	{192, 12, 4, 1, 3, 4, 8, 2, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{10, 0, 4, 1, 3, 4, 8, 2, -1, -1, -1, -1},		/* 38.4 MHz */
+};
+
+static const struct dpll_params iva_dpll_params_2330mhz[NUM_SYS_CLKS] = {
+	{1165, 11, -1, -1, 5, 6, -1, -1, -1, -1, -1, -1},	/* 12 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 13 MHz   */
+	{208, 2, -1, -1, 5, 6, -1, -1, -1, -1, -1, -1},		/* 16.8 MHz */
+	{182, 2, -1, -1, 5, 6, -1, -1, -1, -1, -1, -1},		/* 19.2 MHz */
+	{224, 4, -1, -1, 5, 6, -1, -1, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{91, 2, -1, -1, 5, 6, -1, -1, -1, -1, -1, -1}		/* 38.4 MHz */
+};
+
+static const struct dpll_params iva_dpll_params_2330mhz_dra7xx[NUM_SYS_CLKS] = {
+	{1165, 11, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 12 MHz   */
+	{233, 3, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 20 MHz */
+	{208, 2, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 16.8 MHz */
+	{182, 2, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 19.2 MHz */
+	{224, 4, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{91, 2, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 38.4 MHz */
+};
+
+/* ABE M & N values with sys_clk as source */
+#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
+static const struct dpll_params
+		abe_dpll_params_sysclk_196608khz[NUM_SYS_CLKS] = {
+	{49, 5, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 12 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 13 MHz   */
+	{35, 5, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 16.8 MHz */
+	{46, 8, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 19.2 MHz */
+	{34, 8, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{64, 24, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}		/* 38.4 MHz */
+};
+#endif
+
+/* ABE M & N values with 32K clock as source */
+#ifndef CONFIG_SYS_OMAP_ABE_SYSCK
+static const struct dpll_params abe_dpll_params_32k_196608khz = {
+	750, 0, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1
+};
+#endif
+
+/* ABE M & N values with sysclk2(22.5792 MHz) as input */
+static const struct dpll_params
+		abe_dpll_params_sysclk2_361267khz[NUM_SYS_CLKS] = {
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 12 MHz   */
+	{16, 1, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1},		/* 20 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 16.8 MHz */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 19.2 MHz */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 38.4 MHz */
+};
+
+static const struct dpll_params usb_dpll_params_1920mhz[NUM_SYS_CLKS] = {
+	{400, 4, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 12 MHz   */
+	{480, 9, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 20 MHz   */
+	{400, 6, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 16.8 MHz */
+	{400, 7, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 19.2 MHz */
+	{480, 12, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{400, 15, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 38.4 MHz */
+};
+
+static const struct dpll_params ddr_dpll_params_2664mhz[NUM_SYS_CLKS] = {
+	{111, 0, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 12 MHz   */
+	{333, 4, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 20 MHz   */
+	{555, 6, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 16.8 MHz */
+	{555, 7, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 19.2 MHz */
+	{666, 12, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{555, 15, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 38.4 MHz */
+};
+
+static const struct dpll_params ddr_dpll_params_2128mhz[NUM_SYS_CLKS] = {
+	{266, 2, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 12 MHz   */
+	{266, 4, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 20 MHz   */
+	{190, 2, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 16.8 MHz */
+	{665, 11, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 19.2 MHz */
+	{532, 12, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{665, 23, 2, 1, 8, -1, -1, -1, -1, -1, -1, -1},		/* 38.4 MHz */
+};
+
+static const struct dpll_params gmac_dpll_params_2000mhz[NUM_SYS_CLKS] = {
+	{250, 2, 4, 10, 40, 8, 10, -1, -1, -1, -1, -1},		/* 12 MHz   */
+	{250, 4, 4, 10, 40, 8, 10, -1, -1, -1, -1, -1},		/* 20 MHz   */
+	{119, 1, 4, 10, 40, 8, 10, -1, -1, -1, -1, -1},		/* 16.8 MHz */
+	{625, 11, 4, 10, 40, 8, 10, -1, -1, -1, -1, -1},	/* 19.2 MHz */
+	{500, 12, 4, 10, 40, 8, 10, -1, -1, -1, -1, -1},	/* 26 MHz   */
+	{-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1},	/* 27 MHz   */
+	{625, 23, 4, 10, 40, 8, 10, -1, -1, -1, -1, -1},	/* 38.4 MHz */
+};
+
+struct dplls omap5_dplls_es1 = {
+	.mpu = mpu_dpll_params_800mhz,
+	.core = core_dpll_params_2128mhz_ddr532,
+	.per = per_dpll_params_768mhz,
+	.iva = iva_dpll_params_2330mhz,
+#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
+	.abe = abe_dpll_params_sysclk_196608khz,
+#else
+	.abe = &abe_dpll_params_32k_196608khz,
+#endif
+	.usb = usb_dpll_params_1920mhz,
+	.ddr = NULL
+};
+
+struct dplls omap5_dplls_es2 = {
+	.mpu = mpu_dpll_params_1ghz,
+	.core = core_dpll_params_2128mhz_ddr532_es2,
+	.per = per_dpll_params_768mhz_es2,
+	.iva = iva_dpll_params_2330mhz,
+#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
+	.abe = abe_dpll_params_sysclk_196608khz,
+#else
+	.abe = &abe_dpll_params_32k_196608khz,
+#endif
+	.usb = usb_dpll_params_1920mhz,
+	.ddr = NULL
+};
+
+struct dplls dra76x_dplls = {
+	.mpu = mpu_dpll_params_1ghz,
+	.core = core_dpll_params_2128mhz_dra7xx,
+	.per = per_dpll_params_768mhz_dra76x,
+	.abe = abe_dpll_params_sysclk2_361267khz,
+	.iva = iva_dpll_params_2330mhz_dra7xx,
+	.usb = usb_dpll_params_1920mhz,
+	.ddr =	ddr_dpll_params_2664mhz,
+	.gmac = gmac_dpll_params_2000mhz,
+};
+
+struct dplls dra7xx_dplls = {
+	.mpu = mpu_dpll_params_1ghz,
+	.core = core_dpll_params_2128mhz_dra7xx,
+	.per = per_dpll_params_768mhz_dra7xx,
+	.abe = abe_dpll_params_sysclk2_361267khz,
+	.iva = iva_dpll_params_2330mhz_dra7xx,
+	.usb = usb_dpll_params_1920mhz,
+	.ddr = ddr_dpll_params_2128mhz,
+	.gmac = gmac_dpll_params_2000mhz,
+};
+
+struct dplls dra72x_dplls = {
+	.mpu = mpu_dpll_params_1ghz,
+	.core = core_dpll_params_2128mhz_dra7xx,
+	.per = per_dpll_params_768mhz_dra7xx,
+	.abe = abe_dpll_params_sysclk2_361267khz,
+	.iva = iva_dpll_params_2330mhz_dra7xx,
+	.usb = usb_dpll_params_1920mhz,
+	.ddr =	ddr_dpll_params_2664mhz,
+	.gmac = gmac_dpll_params_2000mhz,
+};
+
+struct pmic_data palmas = {
+	.base_offset = PALMAS_SMPS_BASE_VOLT_UV,
+	.step = 10000, /* 10 mV represented in uV */
+	/*
+	 * Offset codes 1-6 all give the base voltage in Palmas
+	 * Offset code 0 switches OFF the SMPS
+	 */
+	.start_code = 6,
+	.i2c_slave_addr	= SMPS_I2C_SLAVE_ADDR,
+	.pmic_bus_init	= sri2c_init,
+	.pmic_write	= omap_vc_bypass_send_value,
+	.gpio_en = 0,
+};
+
+/* The TPS659038 and TPS65917 are software-compatible, use common struct */
+struct pmic_data tps659038 = {
+	.base_offset = PALMAS_SMPS_BASE_VOLT_UV,
+	.step = 10000, /* 10 mV represented in uV */
+	/*
+	 * Offset codes 1-6 all give the base voltage in Palmas
+	 * Offset code 0 switches OFF the SMPS
+	 */
+	.start_code = 6,
+	.i2c_slave_addr	= TPS659038_I2C_SLAVE_ADDR,
+	.pmic_bus_init	= gpi2c_init,
+	.pmic_write	= palmas_i2c_write_u8,
+	.gpio_en = 0,
+};
+
+/* The LP87565*/
+struct pmic_data lp87565 = {
+	.base_offset = LP873X_BUCK_BASE_VOLT_UV,
+	.step = 5000, /* 5 mV represented in uV */
+	/*
+	 * Offset codes 0 - 0x13 Invalid.
+	 * Offset codes 0x14 0x17 give 10mV steps
+	 * Offset codes 0x17 through 0x9D give 5mV steps
+	 * So let us start with our operating range from .73V
+	 */
+	.start_code = 0x17,
+	.i2c_slave_addr = 0x60,
+	.pmic_bus_init  = gpi2c_init,
+	.pmic_write     = palmas_i2c_write_u8,
+};
+
+/* The LP8732 and LP8733 are software-compatible, use common struct */
+struct pmic_data lp8733 = {
+	.base_offset = LP873X_BUCK_BASE_VOLT_UV,
+	.step = 5000, /* 5 mV represented in uV */
+	/*
+	 * Offset codes 0 - 0x13 Invalid.
+	 * Offset codes 0x14 0x17 give 10mV steps
+	 * Offset codes 0x17 through 0x9D give 5mV steps
+	 * So let us start with our operating range from .73V
+	 */
+	.start_code = 0x17,
+	.i2c_slave_addr = 0x60,
+	.pmic_bus_init  = gpi2c_init,
+	.pmic_write     = palmas_i2c_write_u8,
+};
+
+struct vcores_data omap5430_volts = {
+	.mpu.value[OPP_NOM] = VDD_MPU,
+	.mpu.addr = SMPS_REG_ADDR_12_MPU,
+	.mpu.pmic = &palmas,
+
+	.core.value[OPP_NOM] = VDD_CORE,
+	.core.addr = SMPS_REG_ADDR_8_CORE,
+	.core.pmic = &palmas,
+
+	.mm.value[OPP_NOM] = VDD_MM,
+	.mm.addr = SMPS_REG_ADDR_45_IVA,
+	.mm.pmic = &palmas,
+};
+
+struct vcores_data omap5430_volts_es2 = {
+	.mpu.value[OPP_NOM] = VDD_MPU_ES2,
+	.mpu.addr = SMPS_REG_ADDR_12_MPU,
+	.mpu.pmic = &palmas,
+	.mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK,
+
+	.core.value[OPP_NOM] = VDD_CORE_ES2,
+	.core.addr = SMPS_REG_ADDR_8_CORE,
+	.core.pmic = &palmas,
+
+	.mm.value[OPP_NOM] = VDD_MM_ES2,
+	.mm.addr = SMPS_REG_ADDR_45_IVA,
+	.mm.pmic = &palmas,
+	.mm.abb_tx_done_mask = OMAP_ABB_MM_TXDONE_MASK,
+
+	.mpu.efuse.reg[OPP_NOM]	= OMAP5_ES2_PROD_MPU_OPNO_VMIN,
+	.mpu.efuse.reg_bits	= OMAP5_ES2_PROD_REGBITS,
+
+	.core.efuse.reg[OPP_NOM] = OMAP5_ES2_PROD_CORE_OPNO_VMIN,
+	.core.efuse.reg_bits	= OMAP5_ES2_PROD_REGBITS,
+
+	.mm.efuse.reg[OPP_NOM]	= OMAP5_ES2_PROD_MM_OPNO_VMIN,
+	.mm.efuse.reg_bits	= OMAP5_ES2_PROD_REGBITS,
+};
+
+/*
+ * Enable essential clock domains, modules and
+ * do some additional special settings needed
+ */
+void enable_basic_clocks(void)
+{
+	u32 const clk_domains_essential[] = {
+		(*prcm)->cm_l4per_clkstctrl,
+		(*prcm)->cm_l3init_clkstctrl,
+		(*prcm)->cm_memif_clkstctrl,
+		(*prcm)->cm_l4cfg_clkstctrl,
+#ifdef CONFIG_DRIVER_TI_CPSW
+		(*prcm)->cm_gmac_clkstctrl,
+#endif
+		0
+	};
+
+	u32 const clk_modules_hw_auto_essential[] = {
+		(*prcm)->cm_l3_gpmc_clkctrl,
+		(*prcm)->cm_memif_emif_1_clkctrl,
+		(*prcm)->cm_memif_emif_2_clkctrl,
+		(*prcm)->cm_l4cfg_l4_cfg_clkctrl,
+		(*prcm)->cm_wkup_gpio1_clkctrl,
+		(*prcm)->cm_l4per_gpio2_clkctrl,
+		(*prcm)->cm_l4per_gpio3_clkctrl,
+		(*prcm)->cm_l4per_gpio4_clkctrl,
+		(*prcm)->cm_l4per_gpio5_clkctrl,
+		(*prcm)->cm_l4per_gpio6_clkctrl,
+		(*prcm)->cm_l4per_gpio7_clkctrl,
+		(*prcm)->cm_l4per_gpio8_clkctrl,
+#ifdef CONFIG_SCSI_AHCI_PLAT
+		(*prcm)->cm_l3init_ocp2scp3_clkctrl,
+#endif
+		0
+	};
+
+	u32 const clk_modules_explicit_en_essential[] = {
+		(*prcm)->cm_wkup_gptimer1_clkctrl,
+		(*prcm)->cm_l3init_hsmmc1_clkctrl,
+		(*prcm)->cm_l3init_hsmmc2_clkctrl,
+		(*prcm)->cm_l4per_gptimer2_clkctrl,
+		(*prcm)->cm_wkup_wdtimer2_clkctrl,
+		(*prcm)->cm_l4per_uart1_clkctrl,
+		(*prcm)->cm_l4per_uart3_clkctrl,
+		(*prcm)->cm_l4per_i2c1_clkctrl,
+#ifdef CONFIG_DRIVER_TI_CPSW
+		(*prcm)->cm_gmac_gmac_clkctrl,
+#endif
+
+#ifdef CONFIG_TI_QSPI
+		(*prcm)->cm_l4per_qspi_clkctrl,
+#endif
+#ifdef CONFIG_SCSI_AHCI_PLAT
+		(*prcm)->cm_l3init_sata_clkctrl,
+#endif
+		0
+	};
+
+	/* Enable optional additional functional clock for GPIO4 */
+	setbits_le32((*prcm)->cm_l4per_gpio4_clkctrl,
+			GPIO4_CLKCTRL_OPTFCLKEN_MASK);
+
+	/* Enable 192 MHz clock for MMC1 & MMC2 */
+	setbits_le32((*prcm)->cm_l3init_hsmmc1_clkctrl,
+			HSMMC_CLKCTRL_CLKSEL_MASK);
+	setbits_le32((*prcm)->cm_l3init_hsmmc2_clkctrl,
+			HSMMC_CLKCTRL_CLKSEL_MASK);
+
+	/* Set the correct clock dividers for mmc */
+	clrbits_le32((*prcm)->cm_l3init_hsmmc1_clkctrl,
+		     HSMMC_CLKCTRL_CLKSEL_DIV_MASK);
+	clrbits_le32((*prcm)->cm_l3init_hsmmc2_clkctrl,
+		     HSMMC_CLKCTRL_CLKSEL_DIV_MASK);
+
+	/* Select 32KHz clock as the source of GPTIMER1 */
+	setbits_le32((*prcm)->cm_wkup_gptimer1_clkctrl,
+			GPTIMER1_CLKCTRL_CLKSEL_MASK);
+
+	do_enable_clocks(clk_domains_essential,
+			 clk_modules_hw_auto_essential,
+			 clk_modules_explicit_en_essential,
+			 1);
+
+#ifdef CONFIG_TI_QSPI
+	setbits_le32((*prcm)->cm_l4per_qspi_clkctrl, (1<<24));
+#endif
+
+#ifdef CONFIG_SCSI_AHCI_PLAT
+	/* Enable optional functional clock for SATA */
+	setbits_le32((*prcm)->cm_l3init_sata_clkctrl,
+		     SATA_CLKCTRL_OPTFCLKEN_MASK);
+#endif
+
+	/* Enable SCRM OPT clocks for PER and CORE dpll */
+	setbits_le32((*prcm)->cm_wkupaon_scrm_clkctrl,
+			OPTFCLKEN_SCRM_PER_MASK);
+	setbits_le32((*prcm)->cm_wkupaon_scrm_clkctrl,
+			OPTFCLKEN_SCRM_CORE_MASK);
+}
+
+void enable_basic_uboot_clocks(void)
+{
+	u32 const clk_domains_essential[] = {
+#if defined(CONFIG_DRA7XX)
+		(*prcm)->cm_ipu_clkstctrl,
+#endif
+		0
+	};
+
+	u32 const clk_modules_hw_auto_essential[] = {
+		(*prcm)->cm_l3init_hsusbtll_clkctrl,
+		0
+	};
+
+	u32 const clk_modules_explicit_en_essential[] = {
+		(*prcm)->cm_l4per_mcspi1_clkctrl,
+		(*prcm)->cm_l4per_i2c2_clkctrl,
+		(*prcm)->cm_l4per_i2c3_clkctrl,
+		(*prcm)->cm_l4per_i2c4_clkctrl,
+#if defined(CONFIG_DRA7XX)
+		(*prcm)->cm_ipu_i2c5_clkctrl,
+#else
+		(*prcm)->cm_l4per_i2c5_clkctrl,
+#endif
+		(*prcm)->cm_l3init_hsusbhost_clkctrl,
+		(*prcm)->cm_l3init_fsusb_clkctrl,
+		0
+	};
+	do_enable_clocks(clk_domains_essential,
+			 clk_modules_hw_auto_essential,
+			 clk_modules_explicit_en_essential,
+			 1);
+}
+
+#ifdef CONFIG_TI_EDMA3
+void enable_edma3_clocks(void)
+{
+	u32 const clk_domains_edma3[] = {
+		0
+	};
+
+	u32 const clk_modules_hw_auto_edma3[] = {
+		(*prcm)->cm_l3main1_tptc1_clkctrl,
+		(*prcm)->cm_l3main1_tptc2_clkctrl,
+		0
+	};
+
+	u32 const clk_modules_explicit_en_edma3[] = {
+		0
+	};
+
+	do_enable_clocks(clk_domains_edma3,
+			 clk_modules_hw_auto_edma3,
+			 clk_modules_explicit_en_edma3,
+			 1);
+}
+
+void disable_edma3_clocks(void)
+{
+	u32 const clk_domains_edma3[] = {
+		0
+	};
+
+	u32 const clk_modules_disable_edma3[] = {
+		(*prcm)->cm_l3main1_tptc1_clkctrl,
+		(*prcm)->cm_l3main1_tptc2_clkctrl,
+		0
+	};
+
+	do_disable_clocks(clk_domains_edma3,
+			  clk_modules_disable_edma3,
+			  1);
+}
+#endif
+
+#if defined(CONFIG_USB_DWC3) || defined(CONFIG_USB_XHCI_OMAP)
+void enable_usb_clocks(int index)
+{
+	u32 cm_l3init_usb_otg_ss_clkctrl = 0;
+
+	if (index == 0) {
+		cm_l3init_usb_otg_ss_clkctrl =
+			(*prcm)->cm_l3init_usb_otg_ss1_clkctrl;
+		/* Enable 960 MHz clock for dwc3 */
+		setbits_le32((*prcm)->cm_l3init_usb_otg_ss1_clkctrl,
+			     OPTFCLKEN_REFCLK960M);
+
+		/* Enable 32 KHz clock for USB_PHY1 */
+		setbits_le32((*prcm)->cm_coreaon_usb_phy1_core_clkctrl,
+			     USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K);
+
+		/* Enable 32 KHz clock for USB_PHY3 */
+		if (is_dra7xx())
+			setbits_le32((*prcm)->cm_coreaon_usb_phy3_core_clkctrl,
+				     USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K);
+	} else if (index == 1) {
+		cm_l3init_usb_otg_ss_clkctrl =
+			(*prcm)->cm_l3init_usb_otg_ss2_clkctrl;
+		/* Enable 960 MHz clock for dwc3 */
+		setbits_le32((*prcm)->cm_l3init_usb_otg_ss2_clkctrl,
+			     OPTFCLKEN_REFCLK960M);
+
+		/* Enable 32 KHz clock for dwc3 */
+		setbits_le32((*prcm)->cm_coreaon_usb_phy2_core_clkctrl,
+			     USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K);
+
+		/* Enable 60 MHz clock for USB2PHY2 */
+		setbits_le32((*prcm)->cm_coreaon_l3init_60m_gfclk_clkctrl,
+			     L3INIT_CLKCTRL_OPTFCLKEN_60M_GFCLK);
+	}
+
+	u32 const clk_domains_usb[] = {
+		0
+	};
+
+	u32 const clk_modules_hw_auto_usb[] = {
+		(*prcm)->cm_l3init_ocp2scp1_clkctrl,
+		cm_l3init_usb_otg_ss_clkctrl,
+		0
+	};
+
+	u32 const clk_modules_explicit_en_usb[] = {
+		0
+	};
+
+	do_enable_clocks(clk_domains_usb,
+			 clk_modules_hw_auto_usb,
+			 clk_modules_explicit_en_usb,
+			 1);
+}
+
+void disable_usb_clocks(int index)
+{
+	u32 cm_l3init_usb_otg_ss_clkctrl = 0;
+
+	if (index == 0) {
+		cm_l3init_usb_otg_ss_clkctrl =
+			(*prcm)->cm_l3init_usb_otg_ss1_clkctrl;
+		/* Disable 960 MHz clock for dwc3 */
+		clrbits_le32((*prcm)->cm_l3init_usb_otg_ss1_clkctrl,
+			     OPTFCLKEN_REFCLK960M);
+
+		/* Disable 32 KHz clock for USB_PHY1 */
+		clrbits_le32((*prcm)->cm_coreaon_usb_phy1_core_clkctrl,
+			     USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K);
+
+		/* Disable 32 KHz clock for USB_PHY3 */
+		if (is_dra7xx())
+			clrbits_le32((*prcm)->cm_coreaon_usb_phy3_core_clkctrl,
+				     USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K);
+	} else if (index == 1) {
+		cm_l3init_usb_otg_ss_clkctrl =
+			(*prcm)->cm_l3init_usb_otg_ss2_clkctrl;
+		/* Disable 960 MHz clock for dwc3 */
+		clrbits_le32((*prcm)->cm_l3init_usb_otg_ss2_clkctrl,
+			     OPTFCLKEN_REFCLK960M);
+
+		/* Disable 32 KHz clock for dwc3 */
+		clrbits_le32((*prcm)->cm_coreaon_usb_phy2_core_clkctrl,
+			     USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K);
+
+		/* Disable 60 MHz clock for USB2PHY2 */
+		clrbits_le32((*prcm)->cm_coreaon_l3init_60m_gfclk_clkctrl,
+			     L3INIT_CLKCTRL_OPTFCLKEN_60M_GFCLK);
+	}
+
+	u32 const clk_domains_usb[] = {
+		0
+	};
+
+	u32 const clk_modules_disable[] = {
+		(*prcm)->cm_l3init_ocp2scp1_clkctrl,
+		cm_l3init_usb_otg_ss_clkctrl,
+		0
+	};
+
+	do_disable_clocks(clk_domains_usb,
+			  clk_modules_disable,
+			  1);
+}
+#endif
+
+const struct ctrl_ioregs ioregs_omap5430 = {
+	.ctrl_ddrch = DDR_IO_I_34OHM_SR_FASTEST_WD_DQ_NO_PULL_DQS_PULL_DOWN,
+	.ctrl_lpddr2ch = DDR_IO_I_34OHM_SR_FASTEST_WD_CK_CKE_NCS_CA_PULL_DOWN,
+	.ctrl_ddrio_0 = DDR_IO_0_DDR2_DQ_INT_EN_ALL_DDR3_CA_DIS_ALL,
+	.ctrl_ddrio_1 = DDR_IO_1_DQ_OUT_EN_ALL_DQ_INT_EN_ALL,
+	.ctrl_ddrio_2 = DDR_IO_2_CA_OUT_EN_ALL_CA_INT_EN_ALL,
+};
+
+const struct ctrl_ioregs ioregs_omap5432_es1 = {
+	.ctrl_ddrch = DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL,
+	.ctrl_lpddr2ch = 0x0,
+	.ctrl_ddr3ch = DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL,
+	.ctrl_ddrio_0 = DDR_IO_0_VREF_CELLS_DDR3_VALUE,
+	.ctrl_ddrio_1 = DDR_IO_1_VREF_CELLS_DDR3_VALUE,
+	.ctrl_ddrio_2 = DDR_IO_2_VREF_CELLS_DDR3_VALUE,
+	.ctrl_emif_sdram_config_ext = SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES,
+	.ctrl_emif_sdram_config_ext_final = SDRAM_CONFIG_EXT_RD_LVL_4_SAMPLES,
+};
+
+const struct ctrl_ioregs ioregs_omap5432_es2 = {
+	.ctrl_ddrch = DDR_IO_I_40OHM_SR_FAST_WD_DQ_NO_PULL_DQS_NO_PULL_ES2,
+	.ctrl_lpddr2ch = 0x0,
+	.ctrl_ddr3ch = DDR_IO_I_40OHM_SR_SLOWEST_WD_DQ_NO_PULL_DQS_NO_PULL_ES2,
+	.ctrl_ddrio_0 = DDR_IO_0_VREF_CELLS_DDR3_VALUE_ES2,
+	.ctrl_ddrio_1 = DDR_IO_1_VREF_CELLS_DDR3_VALUE_ES2,
+	.ctrl_ddrio_2 = DDR_IO_2_VREF_CELLS_DDR3_VALUE_ES2,
+	.ctrl_emif_sdram_config_ext = SDRAM_CONFIG_EXT_RD_LVL_11_SAMPLES,
+	.ctrl_emif_sdram_config_ext_final = SDRAM_CONFIG_EXT_RD_LVL_4_SAMPLES,
+};
+
+const struct ctrl_ioregs ioregs_dra7xx_es1 = {
+	.ctrl_ddrch = 0x40404040,
+	.ctrl_lpddr2ch = 0x40404040,
+	.ctrl_ddr3ch = 0x80808080,
+	.ctrl_ddrio_0 = 0x00094A40,
+	.ctrl_ddrio_1 = 0x04A52000,
+	.ctrl_ddrio_2 = 0x84210000,
+	.ctrl_emif_sdram_config_ext = 0x0001C1A7,
+	.ctrl_emif_sdram_config_ext_final = 0x0001C1A7,
+	.ctrl_ddr_ctrl_ext_0 = 0xA2000000,
+};
+
+const struct ctrl_ioregs ioregs_dra72x_es1 = {
+	.ctrl_ddrch = 0x40404040,
+	.ctrl_lpddr2ch = 0x40404040,
+	.ctrl_ddr3ch = 0x60606080,
+	.ctrl_ddrio_0 = 0x00094A40,
+	.ctrl_ddrio_1 = 0x04A52000,
+	.ctrl_ddrio_2 = 0x84210000,
+	.ctrl_emif_sdram_config_ext = 0x0001C1A7,
+	.ctrl_emif_sdram_config_ext_final = 0x0001C1A7,
+	.ctrl_ddr_ctrl_ext_0 = 0xA2000000,
+};
+
+const struct ctrl_ioregs ioregs_dra72x_es2 = {
+	.ctrl_ddrch = 0x40404040,
+	.ctrl_lpddr2ch = 0x40404040,
+	.ctrl_ddr3ch = 0x60606060,
+	.ctrl_ddrio_0 = 0x00094A40,
+	.ctrl_ddrio_1 = 0x00000000,
+	.ctrl_ddrio_2 = 0x00000000,
+	.ctrl_emif_sdram_config_ext = 0x0001C1A7,
+	.ctrl_emif_sdram_config_ext_final = 0x0001C1A7,
+	.ctrl_ddr_ctrl_ext_0 = 0xA2000000,
+};
+
+void __weak hw_data_init(void)
+{
+	u32 omap_rev = omap_revision();
+
+	switch (omap_rev) {
+
+	case OMAP5430_ES1_0:
+	case OMAP5432_ES1_0:
+	*prcm = &omap5_es1_prcm;
+	*dplls_data = &omap5_dplls_es1;
+	*omap_vcores = &omap5430_volts;
+	*ctrl = &omap5_ctrl;
+	break;
+
+	case OMAP5430_ES2_0:
+	case OMAP5432_ES2_0:
+	*prcm = &omap5_es2_prcm;
+	*dplls_data = &omap5_dplls_es2;
+	*omap_vcores = &omap5430_volts_es2;
+	*ctrl = &omap5_ctrl;
+	break;
+
+	case DRA762_ABZ_ES1_0:
+	case DRA762_ACD_ES1_0:
+	case DRA762_ES1_0:
+	*prcm = &dra7xx_prcm;
+	*dplls_data = &dra76x_dplls;
+	*ctrl = &dra7xx_ctrl;
+	break;
+
+	case DRA752_ES1_0:
+	case DRA752_ES1_1:
+	case DRA752_ES2_0:
+	*prcm = &dra7xx_prcm;
+	*dplls_data = &dra7xx_dplls;
+	*ctrl = &dra7xx_ctrl;
+	break;
+
+	case DRA722_ES1_0:
+	case DRA722_ES2_0:
+	case DRA722_ES2_1:
+	*prcm = &dra7xx_prcm;
+	*dplls_data = &dra72x_dplls;
+	*ctrl = &dra7xx_ctrl;
+	break;
+
+	default:
+		printf("\n INVALID OMAP REVISION ");
+	}
+}
+
+void get_ioregs(const struct ctrl_ioregs **regs)
+{
+	u32 omap_rev = omap_revision();
+
+	switch (omap_rev) {
+	case OMAP5430_ES1_0:
+	case OMAP5430_ES2_0:
+		*regs = &ioregs_omap5430;
+		break;
+	case OMAP5432_ES1_0:
+		*regs = &ioregs_omap5432_es1;
+		break;
+	case OMAP5432_ES2_0:
+		*regs = &ioregs_omap5432_es2;
+		break;
+	case DRA752_ES1_0:
+	case DRA752_ES1_1:
+	case DRA752_ES2_0:
+	case DRA762_ES1_0:
+	case DRA762_ACD_ES1_0:
+	case DRA762_ABZ_ES1_0:
+		*regs = &ioregs_dra7xx_es1;
+		break;
+	case DRA722_ES1_0:
+		*regs = &ioregs_dra72x_es1;
+		break;
+	case DRA722_ES2_0:
+	case DRA722_ES2_1:
+		*regs = &ioregs_dra72x_es2;
+		break;
+
+	default:
+		printf("\n INVALID OMAP REVISION ");
+	}
+}
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/hwinit.c b/roms/u-boot/arch/arm/mach-omap2/omap5/hwinit.c
new file mode 100644
index 000000000..edab9a929
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/hwinit.c
@@ -0,0 +1,510 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *
+ * Functions for omap5 based boards.
+ *
+ * (C) Copyright 2011
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ *	Aneesh V	<aneesh@ti.com>
+ *	Steve Sakoman	<steve@sakoman.com>
+ *	Sricharan	<r.sricharan@ti.com>
+ */
+#include <common.h>
+#include <cpu_func.h>
+#include <palmas.h>
+#include <asm/armv7.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/clock.h>
+#include <linux/delay.h>
+#include <linux/sizes.h>
+#include <asm/utils.h>
+#include <asm/arch/gpio.h>
+#include <asm/emif.h>
+#include <asm/omap_common.h>
+
+u32 *const omap_si_rev = (u32 *)OMAP_SRAM_SCRATCH_OMAP_REV;
+
+#if !CONFIG_IS_ENABLED(DM_GPIO)
+static struct gpio_bank gpio_bank_54xx[8] = {
+	{ (void *)OMAP54XX_GPIO1_BASE },
+	{ (void *)OMAP54XX_GPIO2_BASE },
+	{ (void *)OMAP54XX_GPIO3_BASE },
+	{ (void *)OMAP54XX_GPIO4_BASE },
+	{ (void *)OMAP54XX_GPIO5_BASE },
+	{ (void *)OMAP54XX_GPIO6_BASE },
+	{ (void *)OMAP54XX_GPIO7_BASE },
+	{ (void *)OMAP54XX_GPIO8_BASE },
+};
+
+const struct gpio_bank *const omap_gpio_bank = gpio_bank_54xx;
+#endif
+
+void do_set_mux32(u32 base, struct pad_conf_entry const *array, int size)
+{
+	int i;
+	struct pad_conf_entry *pad = (struct pad_conf_entry *)array;
+
+	for (i = 0; i < size; i++, pad++)
+		writel(pad->val, base + pad->offset);
+}
+
+#ifdef CONFIG_SPL_BUILD
+/* LPDDR2 specific IO settings */
+static void io_settings_lpddr2(void)
+{
+	const struct ctrl_ioregs *ioregs;
+
+	get_ioregs(&ioregs);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_1);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_1);
+	writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_0);
+	writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_1);
+	writel(ioregs->ctrl_ddrio_0, (*ctrl)->control_ddrio_0);
+	writel(ioregs->ctrl_ddrio_1, (*ctrl)->control_ddrio_1);
+	writel(ioregs->ctrl_ddrio_2, (*ctrl)->control_ddrio_2);
+}
+
+/* DDR3 specific IO settings */
+static void io_settings_ddr3(void)
+{
+	u32 io_settings = 0;
+	const struct ctrl_ioregs *ioregs;
+
+	get_ioregs(&ioregs);
+	writel(ioregs->ctrl_ddr3ch, (*ctrl)->control_ddr3ch1_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_1);
+
+	writel(ioregs->ctrl_ddr3ch, (*ctrl)->control_ddr3ch2_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_0);
+	writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_1);
+
+	writel(ioregs->ctrl_ddrio_0, (*ctrl)->control_ddrio_0);
+	writel(ioregs->ctrl_ddrio_1, (*ctrl)->control_ddrio_1);
+
+	if (!is_dra7xx()) {
+		writel(ioregs->ctrl_ddrio_2, (*ctrl)->control_ddrio_2);
+		writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_1);
+	}
+
+	/* omap5432 does not use lpddr2 */
+	writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_0);
+
+	writel(ioregs->ctrl_emif_sdram_config_ext,
+	       (*ctrl)->control_emif1_sdram_config_ext);
+	if (!is_dra72x())
+		writel(ioregs->ctrl_emif_sdram_config_ext,
+		       (*ctrl)->control_emif2_sdram_config_ext);
+
+	if (is_omap54xx()) {
+		/* Disable DLL select */
+		io_settings = (readl((*ctrl)->control_port_emif1_sdram_config)
+							& 0xFFEFFFFF);
+		writel(io_settings,
+			(*ctrl)->control_port_emif1_sdram_config);
+
+		io_settings = (readl((*ctrl)->control_port_emif2_sdram_config)
+							& 0xFFEFFFFF);
+		writel(io_settings,
+			(*ctrl)->control_port_emif2_sdram_config);
+	} else {
+		writel(ioregs->ctrl_ddr_ctrl_ext_0,
+				(*ctrl)->control_ddr_control_ext_0);
+	}
+}
+
+/*
+ * Some tuning of IOs for optimal power and performance
+ */
+void do_io_settings(void)
+{
+	u32 io_settings = 0, mask = 0;
+	struct emif_reg_struct *emif = (struct emif_reg_struct *)EMIF1_BASE;
+
+	/* Impedance settings EMMC, C2C 1,2, hsi2 */
+	mask = (ds_mask << 2) | (ds_mask << 8) |
+		(ds_mask << 16) | (ds_mask << 18);
+	io_settings = readl((*ctrl)->control_smart1io_padconf_0) &
+				(~mask);
+	io_settings |= (ds_60_ohm << 8) | (ds_45_ohm << 16) |
+			(ds_45_ohm << 18) | (ds_60_ohm << 2);
+	writel(io_settings, (*ctrl)->control_smart1io_padconf_0);
+
+	/* Impedance settings Mcspi2 */
+	mask = (ds_mask << 30);
+	io_settings = readl((*ctrl)->control_smart1io_padconf_1) &
+			(~mask);
+	io_settings |= (ds_60_ohm << 30);
+	writel(io_settings, (*ctrl)->control_smart1io_padconf_1);
+
+	/* Impedance settings C2C 3,4 */
+	mask = (ds_mask << 14) | (ds_mask << 16);
+	io_settings = readl((*ctrl)->control_smart1io_padconf_2) &
+			(~mask);
+	io_settings |= (ds_45_ohm << 14) | (ds_45_ohm << 16);
+	writel(io_settings, (*ctrl)->control_smart1io_padconf_2);
+
+	/* Slew rate settings EMMC, C2C 1,2 */
+	mask = (sc_mask << 8) | (sc_mask << 16) | (sc_mask << 18);
+	io_settings = readl((*ctrl)->control_smart2io_padconf_0) &
+			(~mask);
+	io_settings |= (sc_fast << 8) | (sc_na << 16) | (sc_na << 18);
+	writel(io_settings, (*ctrl)->control_smart2io_padconf_0);
+
+	/* Slew rate settings hsi2, Mcspi2 */
+	mask = (sc_mask << 24) | (sc_mask << 28);
+	io_settings = readl((*ctrl)->control_smart2io_padconf_1) &
+			(~mask);
+	io_settings |= (sc_fast << 28) | (sc_fast << 24);
+	writel(io_settings, (*ctrl)->control_smart2io_padconf_1);
+
+	/* Slew rate settings C2C 3,4 */
+	mask = (sc_mask << 16) | (sc_mask << 18);
+	io_settings = readl((*ctrl)->control_smart2io_padconf_2) &
+			(~mask);
+	io_settings |= (sc_na << 16) | (sc_na << 18);
+	writel(io_settings, (*ctrl)->control_smart2io_padconf_2);
+
+	/* impedance and slew rate settings for usb */
+	mask = (usb_i_mask << 29) | (usb_i_mask << 26) | (usb_i_mask << 23) |
+		(usb_i_mask << 20) | (usb_i_mask << 17) | (usb_i_mask << 14);
+	io_settings = readl((*ctrl)->control_smart3io_padconf_1) &
+			(~mask);
+	io_settings |= (ds_60_ohm << 29) | (ds_60_ohm << 26) |
+		       (ds_60_ohm << 23) | (sc_fast << 20) |
+		       (sc_fast << 17) | (sc_fast << 14);
+	writel(io_settings, (*ctrl)->control_smart3io_padconf_1);
+
+	if (emif_sdram_type(emif->emif_sdram_config) == EMIF_SDRAM_TYPE_LPDDR2)
+		io_settings_lpddr2();
+	else
+		io_settings_ddr3();
+}
+
+static const struct srcomp_params srcomp_parameters[NUM_SYS_CLKS] = {
+	{0x45, 0x1},	/* 12 MHz   */
+	{-1, -1},	/* 13 MHz   */
+	{0x63, 0x2},	/* 16.8 MHz */
+	{0x57, 0x2},	/* 19.2 MHz */
+	{0x20, 0x1},	/* 26 MHz   */
+	{-1, -1},	/* 27 MHz   */
+	{0x41, 0x3}	/* 38.4 MHz */
+};
+
+void srcomp_enable(void)
+{
+	u32 srcomp_value, mul_factor, div_factor, clk_val, i;
+	u32 sysclk_ind	= get_sys_clk_index();
+	u32 omap_rev	= omap_revision();
+
+	if (!is_omap54xx())
+		return;
+
+	mul_factor = srcomp_parameters[sysclk_ind].multiply_factor;
+	div_factor = srcomp_parameters[sysclk_ind].divide_factor;
+
+	for (i = 0; i < 4; i++) {
+		srcomp_value = readl((*ctrl)->control_srcomp_north_side + i*4);
+		srcomp_value &=
+			~(MULTIPLY_FACTOR_XS_MASK | DIVIDE_FACTOR_XS_MASK);
+		srcomp_value |= (mul_factor << MULTIPLY_FACTOR_XS_SHIFT) |
+			(div_factor << DIVIDE_FACTOR_XS_SHIFT);
+		writel(srcomp_value, (*ctrl)->control_srcomp_north_side + i*4);
+	}
+
+	if ((omap_rev == OMAP5430_ES1_0) || (omap_rev == OMAP5432_ES1_0)) {
+		clk_val = readl((*prcm)->cm_coreaon_io_srcomp_clkctrl);
+		clk_val |= OPTFCLKEN_SRCOMP_FCLK_MASK;
+		writel(clk_val, (*prcm)->cm_coreaon_io_srcomp_clkctrl);
+
+		for (i = 0; i < 4; i++) {
+			srcomp_value =
+				readl((*ctrl)->control_srcomp_north_side + i*4);
+			srcomp_value &= ~PWRDWN_XS_MASK;
+			writel(srcomp_value,
+			       (*ctrl)->control_srcomp_north_side + i*4);
+
+			while (((readl((*ctrl)->control_srcomp_north_side + i*4)
+				& SRCODE_READ_XS_MASK) >>
+				SRCODE_READ_XS_SHIFT) == 0)
+				;
+
+			srcomp_value =
+				readl((*ctrl)->control_srcomp_north_side + i*4);
+			srcomp_value &= ~OVERRIDE_XS_MASK;
+			writel(srcomp_value,
+			       (*ctrl)->control_srcomp_north_side + i*4);
+		}
+	} else {
+		srcomp_value = readl((*ctrl)->control_srcomp_east_side_wkup);
+		srcomp_value &= ~(MULTIPLY_FACTOR_XS_MASK |
+				  DIVIDE_FACTOR_XS_MASK);
+		srcomp_value |= (mul_factor << MULTIPLY_FACTOR_XS_SHIFT) |
+				(div_factor << DIVIDE_FACTOR_XS_SHIFT);
+		writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
+
+		for (i = 0; i < 4; i++) {
+			srcomp_value =
+				readl((*ctrl)->control_srcomp_north_side + i*4);
+			srcomp_value |= SRCODE_OVERRIDE_SEL_XS_MASK;
+			writel(srcomp_value,
+			       (*ctrl)->control_srcomp_north_side + i*4);
+
+			srcomp_value =
+				readl((*ctrl)->control_srcomp_north_side + i*4);
+			srcomp_value &= ~OVERRIDE_XS_MASK;
+			writel(srcomp_value,
+			       (*ctrl)->control_srcomp_north_side + i*4);
+		}
+
+		srcomp_value =
+			readl((*ctrl)->control_srcomp_east_side_wkup);
+		srcomp_value |= SRCODE_OVERRIDE_SEL_XS_MASK;
+		writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
+
+		srcomp_value =
+			readl((*ctrl)->control_srcomp_east_side_wkup);
+		srcomp_value &= ~OVERRIDE_XS_MASK;
+		writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
+
+		clk_val = readl((*prcm)->cm_coreaon_io_srcomp_clkctrl);
+		clk_val |= OPTFCLKEN_SRCOMP_FCLK_MASK;
+		writel(clk_val, (*prcm)->cm_coreaon_io_srcomp_clkctrl);
+
+		clk_val = readl((*prcm)->cm_wkupaon_io_srcomp_clkctrl);
+		clk_val |= OPTFCLKEN_SRCOMP_FCLK_MASK;
+		writel(clk_val, (*prcm)->cm_wkupaon_io_srcomp_clkctrl);
+
+		for (i = 0; i < 4; i++) {
+			while (((readl((*ctrl)->control_srcomp_north_side + i*4)
+				& SRCODE_READ_XS_MASK) >>
+				SRCODE_READ_XS_SHIFT) == 0)
+				;
+
+			srcomp_value =
+				readl((*ctrl)->control_srcomp_north_side + i*4);
+			srcomp_value &= ~SRCODE_OVERRIDE_SEL_XS_MASK;
+			writel(srcomp_value,
+			       (*ctrl)->control_srcomp_north_side + i*4);
+		}
+
+		while (((readl((*ctrl)->control_srcomp_east_side_wkup) &
+			SRCODE_READ_XS_MASK) >> SRCODE_READ_XS_SHIFT) == 0)
+			;
+
+		srcomp_value =
+			readl((*ctrl)->control_srcomp_east_side_wkup);
+		srcomp_value &= ~SRCODE_OVERRIDE_SEL_XS_MASK;
+		writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
+	}
+}
+#endif
+
+void config_data_eye_leveling_samples(u32 emif_base)
+{
+	const struct ctrl_ioregs *ioregs;
+
+	get_ioregs(&ioregs);
+
+	/*EMIF_SDRAM_CONFIG_EXT-Read data eye leveling no of samples =4*/
+	if (emif_base == EMIF1_BASE)
+		writel(ioregs->ctrl_emif_sdram_config_ext_final,
+		       (*ctrl)->control_emif1_sdram_config_ext);
+	else if (emif_base == EMIF2_BASE)
+		writel(ioregs->ctrl_emif_sdram_config_ext_final,
+		       (*ctrl)->control_emif2_sdram_config_ext);
+}
+
+void init_cpu_configuration(void)
+{
+	u32 l2actlr;
+
+	asm volatile("mrc p15, 1, %0, c15, c0, 0" : "=r"(l2actlr));
+	/*
+	 * L2ACTLR: Ensure to enable the following:
+	 * 3: Disable clean/evict push to external
+	 * 4: Disable WriteUnique and WriteLineUnique transactions from master
+	 * 8: Disable DVM/CMO message broadcast
+	 */
+	l2actlr |= 0x118;
+	omap_smc1(OMAP5_SERVICE_L2ACTLR_SET, l2actlr);
+}
+
+void init_omap_revision(void)
+{
+	/*
+	 * For some of the ES2/ES1 boards ID_CODE is not reliable:
+	 * Also, ES1 and ES2 have different ARM revisions
+	 * So use ARM revision for identification
+	 */
+	unsigned int rev = cortex_rev();
+
+	switch (readl(CONTROL_ID_CODE)) {
+	case OMAP5430_CONTROL_ID_CODE_ES1_0:
+		*omap_si_rev = OMAP5430_ES1_0;
+		if (rev == MIDR_CORTEX_A15_R2P2)
+			*omap_si_rev = OMAP5430_ES2_0;
+		break;
+	case OMAP5432_CONTROL_ID_CODE_ES1_0:
+		*omap_si_rev = OMAP5432_ES1_0;
+		if (rev == MIDR_CORTEX_A15_R2P2)
+			*omap_si_rev = OMAP5432_ES2_0;
+		break;
+	case OMAP5430_CONTROL_ID_CODE_ES2_0:
+		*omap_si_rev = OMAP5430_ES2_0;
+		break;
+	case OMAP5432_CONTROL_ID_CODE_ES2_0:
+		*omap_si_rev = OMAP5432_ES2_0;
+		break;
+	case DRA762_CONTROL_ID_CODE_ES1_0:
+		*omap_si_rev = DRA762_ES1_0;
+		break;
+	case DRA752_CONTROL_ID_CODE_ES1_0:
+		*omap_si_rev = DRA752_ES1_0;
+		break;
+	case DRA752_CONTROL_ID_CODE_ES1_1:
+		*omap_si_rev = DRA752_ES1_1;
+		break;
+	case DRA752_CONTROL_ID_CODE_ES2_0:
+		*omap_si_rev = DRA752_ES2_0;
+		break;
+	case DRA722_CONTROL_ID_CODE_ES1_0:
+		*omap_si_rev = DRA722_ES1_0;
+		break;
+	case DRA722_CONTROL_ID_CODE_ES2_0:
+		*omap_si_rev = DRA722_ES2_0;
+		break;
+	case DRA722_CONTROL_ID_CODE_ES2_1:
+		*omap_si_rev = DRA722_ES2_1;
+		break;
+	default:
+		*omap_si_rev = OMAP5430_SILICON_ID_INVALID;
+	}
+	init_cpu_configuration();
+}
+
+void init_package_revision(void)
+{
+	unsigned int die_id[4] = { 0 };
+	u8 package;
+
+	omap_die_id(die_id);
+	package = (die_id[2] >> 16) & 0x3;
+
+	if (is_dra76x()) {
+		switch (package) {
+		case DRA762_ABZ_PACKAGE:
+			*omap_si_rev = DRA762_ABZ_ES1_0;
+			break;
+		case DRA762_ACD_PACKAGE:
+		default:
+			*omap_si_rev = DRA762_ACD_ES1_0;
+			break;
+		}
+	}
+}
+
+void omap_die_id(unsigned int *die_id)
+{
+	die_id[0] = readl((*ctrl)->control_std_fuse_die_id_0);
+	die_id[1] = readl((*ctrl)->control_std_fuse_die_id_1);
+	die_id[2] = readl((*ctrl)->control_std_fuse_die_id_2);
+	die_id[3] = readl((*ctrl)->control_std_fuse_die_id_3);
+}
+
+void reset_cpu(void)
+{
+	u32 omap_rev = omap_revision();
+
+	/*
+	 * WARM reset is not functional in case of OMAP5430 ES1.0 soc.
+	 * So use cold reset in case instead.
+	 */
+	if (omap_rev == OMAP5430_ES1_0)
+		writel(PRM_RSTCTRL_RESET << 0x1, (*prcm)->prm_rstctrl);
+	else
+		writel(PRM_RSTCTRL_RESET, (*prcm)->prm_rstctrl);
+}
+
+u32 warm_reset(void)
+{
+	return readl((*prcm)->prm_rstst) & PRM_RSTST_WARM_RESET_MASK;
+}
+
+void setup_warmreset_time(void)
+{
+	u32 rst_time, rst_val;
+
+	/*
+	 * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff.
+	 * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles
+	 * into microsec and passing the value.
+	 */
+	rst_time = usec_to_32k(CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC)
+		<< RSTTIME1_SHIFT;
+
+	if (rst_time > RSTTIME1_MASK)
+		rst_time = RSTTIME1_MASK;
+
+	rst_val = readl((*prcm)->prm_rsttime) & ~RSTTIME1_MASK;
+	rst_val |= rst_time;
+	writel(rst_val, (*prcm)->prm_rsttime);
+}
+
+void v7_arch_cp15_set_l2aux_ctrl(u32 l2auxctrl, u32 cpu_midr,
+				 u32 cpu_rev_comb, u32 cpu_variant,
+				 u32 cpu_rev)
+{
+	omap_smc1(OMAP5_SERVICE_L2ACTLR_SET, l2auxctrl);
+}
+
+void v7_arch_cp15_set_acr(u32 acr, u32 cpu_midr, u32 cpu_rev_comb,
+			  u32 cpu_variant, u32 cpu_rev)
+{
+
+#ifdef CONFIG_ARM_ERRATA_801819
+	/*
+	 * DRA72x processors are uniprocessors and DONOT have
+	 * ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
+	 * Extensions) Hence the erratum workaround is not applicable for
+	 * DRA72x processors.
+	 */
+	if (is_dra72x())
+		acr &= ~((0x3 << 23) | (0x3 << 25));
+#endif
+	omap_smc1(OMAP5_SERVICE_ACR_SET, acr);
+}
+
+#if defined(CONFIG_PALMAS_POWER)
+__weak void board_mmc_poweron_ldo(uint voltage)
+{
+	palmas_mmc1_poweron_ldo(LDO1_VOLTAGE, LDO1_CTRL, voltage);
+}
+
+void vmmc_pbias_config(uint voltage)
+{
+	u32 value = 0;
+
+	value = readl((*ctrl)->control_pbias);
+	value &= ~SDCARD_PWRDNZ;
+	writel(value, (*ctrl)->control_pbias);
+	udelay(10); /* wait 10 us */
+	value &= ~SDCARD_BIAS_PWRDNZ;
+	writel(value, (*ctrl)->control_pbias);
+
+	board_mmc_poweron_ldo(voltage);
+
+	value = readl((*ctrl)->control_pbias);
+	value |= SDCARD_BIAS_PWRDNZ;
+	writel(value, (*ctrl)->control_pbias);
+	udelay(150); /* wait 150 us */
+	value |= SDCARD_PWRDNZ;
+	writel(value, (*ctrl)->control_pbias);
+	udelay(150); /* wait 150 us */
+}
+#endif
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/prcm-regs.c b/roms/u-boot/arch/arm/mach-omap2/omap5/prcm-regs.c
new file mode 100644
index 000000000..b5baebc06
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/prcm-regs.c
@@ -0,0 +1,1023 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *
+ * HW regs data for OMAP5 Soc
+ *
+ * (C) Copyright 2013
+ * Texas Instruments, <www.ti.com>
+ *
+ * Sricharan R <r.sricharan@ti.com>
+ */
+
+#include <asm/omap_common.h>
+#include <asm/io.h>
+
+struct prcm_regs const omap5_es1_prcm = {
+	/* cm1.ckgen */
+	.cm_clksel_core = 0x4a004100,
+	.cm_clksel_abe = 0x4a004108,
+	.cm_dll_ctrl = 0x4a004110,
+	.cm_clkmode_dpll_core = 0x4a004120,
+	.cm_idlest_dpll_core = 0x4a004124,
+	.cm_autoidle_dpll_core = 0x4a004128,
+	.cm_clksel_dpll_core = 0x4a00412c,
+	.cm_div_m2_dpll_core = 0x4a004130,
+	.cm_div_m3_dpll_core = 0x4a004134,
+	.cm_div_h11_dpll_core = 0x4a004138,
+	.cm_div_h12_dpll_core = 0x4a00413c,
+	.cm_div_h13_dpll_core = 0x4a004140,
+	.cm_div_h14_dpll_core = 0x4a004144,
+	.cm_ssc_deltamstep_dpll_core = 0x4a004148,
+	.cm_ssc_modfreqdiv_dpll_core = 0x4a00414c,
+	.cm_emu_override_dpll_core = 0x4a004150,
+	.cm_div_h22_dpllcore = 0x4a004154,
+	.cm_div_h23_dpll_core = 0x4a004158,
+	.cm_clkmode_dpll_mpu = 0x4a004160,
+	.cm_idlest_dpll_mpu = 0x4a004164,
+	.cm_autoidle_dpll_mpu = 0x4a004168,
+	.cm_clksel_dpll_mpu = 0x4a00416c,
+	.cm_div_m2_dpll_mpu = 0x4a004170,
+	.cm_ssc_deltamstep_dpll_mpu = 0x4a004188,
+	.cm_ssc_modfreqdiv_dpll_mpu = 0x4a00418c,
+	.cm_bypclk_dpll_mpu = 0x4a00419c,
+	.cm_clkmode_dpll_iva = 0x4a0041a0,
+	.cm_idlest_dpll_iva = 0x4a0041a4,
+	.cm_autoidle_dpll_iva = 0x4a0041a8,
+	.cm_clksel_dpll_iva = 0x4a0041ac,
+	.cm_div_h11_dpll_iva = 0x4a0041b8,
+	.cm_div_h12_dpll_iva = 0x4a0041bc,
+	.cm_ssc_deltamstep_dpll_iva = 0x4a0041c8,
+	.cm_ssc_modfreqdiv_dpll_iva = 0x4a0041cc,
+	.cm_bypclk_dpll_iva = 0x4a0041dc,
+	.cm_clkmode_dpll_abe = 0x4a0041e0,
+	.cm_idlest_dpll_abe = 0x4a0041e4,
+	.cm_autoidle_dpll_abe = 0x4a0041e8,
+	.cm_clksel_dpll_abe = 0x4a0041ec,
+	.cm_div_m2_dpll_abe = 0x4a0041f0,
+	.cm_div_m3_dpll_abe = 0x4a0041f4,
+	.cm_ssc_deltamstep_dpll_abe = 0x4a004208,
+	.cm_ssc_modfreqdiv_dpll_abe = 0x4a00420c,
+	.cm_clkmode_dpll_ddrphy = 0x4a004220,
+	.cm_idlest_dpll_ddrphy = 0x4a004224,
+	.cm_autoidle_dpll_ddrphy = 0x4a004228,
+	.cm_clksel_dpll_ddrphy = 0x4a00422c,
+	.cm_div_m2_dpll_ddrphy = 0x4a004230,
+	.cm_div_h11_dpll_ddrphy = 0x4a004238,
+	.cm_div_h12_dpll_ddrphy = 0x4a00423c,
+	.cm_div_h13_dpll_ddrphy = 0x4a004240,
+	.cm_ssc_deltamstep_dpll_ddrphy = 0x4a004248,
+	.cm_shadow_freq_config1 = 0x4a004260,
+	.cm_mpu_mpu_clkctrl = 0x4a004320,
+
+	/* cm1.dsp */
+	.cm_dsp_clkstctrl = 0x4a004400,
+	.cm_dsp_dsp_clkctrl = 0x4a004420,
+
+	/* cm1.abe */
+	.cm1_abe_clkstctrl = 0x4a004500,
+	.cm1_abe_l4abe_clkctrl = 0x4a004520,
+	.cm1_abe_aess_clkctrl = 0x4a004528,
+	.cm1_abe_pdm_clkctrl = 0x4a004530,
+	.cm1_abe_dmic_clkctrl = 0x4a004538,
+	.cm1_abe_mcasp_clkctrl = 0x4a004540,
+	.cm1_abe_mcbsp1_clkctrl = 0x4a004548,
+	.cm1_abe_mcbsp2_clkctrl = 0x4a004550,
+	.cm1_abe_mcbsp3_clkctrl = 0x4a004558,
+	.cm1_abe_slimbus_clkctrl = 0x4a004560,
+	.cm1_abe_timer5_clkctrl = 0x4a004568,
+	.cm1_abe_timer6_clkctrl = 0x4a004570,
+	.cm1_abe_timer7_clkctrl = 0x4a004578,
+	.cm1_abe_timer8_clkctrl = 0x4a004580,
+	.cm1_abe_wdt3_clkctrl = 0x4a004588,
+
+	/* cm2.ckgen */
+	.cm_clksel_mpu_m3_iss_root = 0x4a008100,
+	.cm_clksel_usb_60mhz = 0x4a008104,
+	.cm_scale_fclk = 0x4a008108,
+	.cm_core_dvfs_perf1 = 0x4a008110,
+	.cm_core_dvfs_perf2 = 0x4a008114,
+	.cm_core_dvfs_perf3 = 0x4a008118,
+	.cm_core_dvfs_perf4 = 0x4a00811c,
+	.cm_core_dvfs_current = 0x4a008124,
+	.cm_iva_dvfs_perf_tesla = 0x4a008128,
+	.cm_iva_dvfs_perf_ivahd = 0x4a00812c,
+	.cm_iva_dvfs_perf_abe = 0x4a008130,
+	.cm_iva_dvfs_current = 0x4a008138,
+	.cm_clkmode_dpll_per = 0x4a008140,
+	.cm_idlest_dpll_per = 0x4a008144,
+	.cm_autoidle_dpll_per = 0x4a008148,
+	.cm_clksel_dpll_per = 0x4a00814c,
+	.cm_div_m2_dpll_per = 0x4a008150,
+	.cm_div_m3_dpll_per = 0x4a008154,
+	.cm_div_h11_dpll_per = 0x4a008158,
+	.cm_div_h12_dpll_per = 0x4a00815c,
+	.cm_div_h14_dpll_per = 0x4a008164,
+	.cm_ssc_deltamstep_dpll_per = 0x4a008168,
+	.cm_ssc_modfreqdiv_dpll_per = 0x4a00816c,
+	.cm_emu_override_dpll_per = 0x4a008170,
+	.cm_clkmode_dpll_usb = 0x4a008180,
+	.cm_idlest_dpll_usb = 0x4a008184,
+	.cm_autoidle_dpll_usb = 0x4a008188,
+	.cm_clksel_dpll_usb = 0x4a00818c,
+	.cm_div_m2_dpll_usb = 0x4a008190,
+	.cm_ssc_deltamstep_dpll_usb = 0x4a0081a8,
+	.cm_ssc_modfreqdiv_dpll_usb = 0x4a0081ac,
+	.cm_clkdcoldo_dpll_usb = 0x4a0081b4,
+	.cm_clkmode_dpll_unipro = 0x4a0081c0,
+	.cm_idlest_dpll_unipro = 0x4a0081c4,
+	.cm_autoidle_dpll_unipro = 0x4a0081c8,
+	.cm_clksel_dpll_unipro = 0x4a0081cc,
+	.cm_div_m2_dpll_unipro = 0x4a0081d0,
+	.cm_ssc_deltamstep_dpll_unipro = 0x4a0081e8,
+	.cm_ssc_modfreqdiv_dpll_unipro = 0x4a0081ec,
+
+	/* cm2.core */
+	.cm_coreaon_bandgap_clkctrl = 0x4a008648,
+	.cm_coreaon_io_srcomp_clkctrl = 0x4a008650,
+	.cm_l3_1_clkstctrl = 0x4a008700,
+	.cm_l3_1_dynamicdep = 0x4a008708,
+	.cm_l3_1_l3_1_clkctrl = 0x4a008720,
+	.cm_l3_2_clkstctrl = 0x4a008800,
+	.cm_l3_2_dynamicdep = 0x4a008808,
+	.cm_l3_2_l3_2_clkctrl = 0x4a008820,
+	.cm_l3_gpmc_clkctrl = 0x4a008828,
+	.cm_l3_2_ocmc_ram_clkctrl = 0x4a008830,
+	.cm_mpu_m3_clkstctrl = 0x4a008900,
+	.cm_mpu_m3_staticdep = 0x4a008904,
+	.cm_mpu_m3_dynamicdep = 0x4a008908,
+	.cm_mpu_m3_mpu_m3_clkctrl = 0x4a008920,
+	.cm_sdma_clkstctrl = 0x4a008a00,
+	.cm_sdma_staticdep = 0x4a008a04,
+	.cm_sdma_dynamicdep = 0x4a008a08,
+	.cm_sdma_sdma_clkctrl = 0x4a008a20,
+	.cm_memif_clkstctrl = 0x4a008b00,
+	.cm_memif_dmm_clkctrl = 0x4a008b20,
+	.cm_memif_emif_fw_clkctrl = 0x4a008b28,
+	.cm_memif_emif_1_clkctrl = 0x4a008b30,
+	.cm_memif_emif_2_clkctrl = 0x4a008b38,
+	.cm_memif_dll_clkctrl = 0x4a008b40,
+	.cm_memif_emif_h1_clkctrl = 0x4a008b50,
+	.cm_memif_emif_h2_clkctrl = 0x4a008b58,
+	.cm_memif_dll_h_clkctrl = 0x4a008b60,
+	.cm_c2c_clkstctrl = 0x4a008c00,
+	.cm_c2c_staticdep = 0x4a008c04,
+	.cm_c2c_dynamicdep = 0x4a008c08,
+	.cm_c2c_sad2d_clkctrl = 0x4a008c20,
+	.cm_c2c_modem_icr_clkctrl = 0x4a008c28,
+	.cm_c2c_sad2d_fw_clkctrl = 0x4a008c30,
+	.cm_l4cfg_clkstctrl = 0x4a008d00,
+	.cm_l4cfg_dynamicdep = 0x4a008d08,
+	.cm_l4cfg_l4_cfg_clkctrl = 0x4a008d20,
+	.cm_l4cfg_hw_sem_clkctrl = 0x4a008d28,
+	.cm_l4cfg_mailbox_clkctrl = 0x4a008d30,
+	.cm_l4cfg_sar_rom_clkctrl = 0x4a008d38,
+	.cm_l3instr_clkstctrl = 0x4a008e00,
+	.cm_l3instr_l3_3_clkctrl = 0x4a008e20,
+	.cm_l3instr_l3_instr_clkctrl = 0x4a008e28,
+	.cm_l3instr_intrconn_wp1_clkctrl = 0x4a008e40,
+
+	/* cm2.ivahd */
+	.cm_ivahd_clkstctrl = 0x4a008f00,
+	.cm_ivahd_ivahd_clkctrl = 0x4a008f20,
+	.cm_ivahd_sl2_clkctrl = 0x4a008f28,
+
+	/* cm2.cam */
+	.cm_cam_clkstctrl = 0x4a009000,
+	.cm_cam_iss_clkctrl = 0x4a009020,
+	.cm_cam_fdif_clkctrl = 0x4a009028,
+
+	/* cm2.dss */
+	.cm_dss_clkstctrl = 0x4a009100,
+	.cm_dss_dss_clkctrl = 0x4a009120,
+
+	/* cm2.sgx */
+	.cm_sgx_clkstctrl = 0x4a009200,
+	.cm_sgx_sgx_clkctrl = 0x4a009220,
+
+	/* cm2.l3init */
+	.cm_l3init_clkstctrl = 0x4a009300,
+	.cm_l3init_hsmmc1_clkctrl = 0x4a009328,
+	.cm_l3init_hsmmc2_clkctrl = 0x4a009330,
+	.cm_l3init_hsi_clkctrl = 0x4a009338,
+	.cm_l3init_hsusbhost_clkctrl = 0x4a009358,
+	.cm_l3init_hsusbotg_clkctrl = 0x4a009360,
+	.cm_l3init_hsusbtll_clkctrl = 0x4a009368,
+	.cm_l3init_p1500_clkctrl = 0x4a009378,
+	.cm_l3init_sata_clkctrl = 0x4a009388,
+	.cm_l3init_fsusb_clkctrl = 0x4a0093d0,
+	.cm_l3init_ocp2scp1_clkctrl = 0x4a0093e0,
+	.cm_l3init_ocp2scp3_clkctrl = 0x4a0093e8,
+
+	/* cm2.l4per */
+	.cm_l4per_clkstctrl = 0x4a009400,
+	.cm_l4per_dynamicdep = 0x4a009408,
+	.cm_l4per_adc_clkctrl = 0x4a009420,
+	.cm_l4per_gptimer10_clkctrl = 0x4a009428,
+	.cm_l4per_gptimer11_clkctrl = 0x4a009430,
+	.cm_l4per_gptimer2_clkctrl = 0x4a009438,
+	.cm_l4per_gptimer3_clkctrl = 0x4a009440,
+	.cm_l4per_gptimer4_clkctrl = 0x4a009448,
+	.cm_l4per_gptimer9_clkctrl = 0x4a009450,
+	.cm_l4per_elm_clkctrl = 0x4a009458,
+	.cm_l4per_gpio2_clkctrl = 0x4a009460,
+	.cm_l4per_gpio3_clkctrl = 0x4a009468,
+	.cm_l4per_gpio4_clkctrl = 0x4a009470,
+	.cm_l4per_gpio5_clkctrl = 0x4a009478,
+	.cm_l4per_gpio6_clkctrl = 0x4a009480,
+	.cm_l4per_hdq1w_clkctrl = 0x4a009488,
+	.cm_l4per_hecc1_clkctrl = 0x4a009490,
+	.cm_l4per_hecc2_clkctrl = 0x4a009498,
+	.cm_l4per_i2c1_clkctrl = 0x4a0094a0,
+	.cm_l4per_i2c2_clkctrl = 0x4a0094a8,
+	.cm_l4per_i2c3_clkctrl = 0x4a0094b0,
+	.cm_l4per_i2c4_clkctrl = 0x4a0094b8,
+	.cm_l4per_l4per_clkctrl = 0x4a0094c0,
+	.cm_l4per_mcasp2_clkctrl = 0x4a0094d0,
+	.cm_l4per_mcasp3_clkctrl = 0x4a0094d8,
+	.cm_l4per_mgate_clkctrl = 0x4a0094e8,
+	.cm_l4per_mcspi1_clkctrl = 0x4a0094f0,
+	.cm_l4per_mcspi2_clkctrl = 0x4a0094f8,
+	.cm_l4per_mcspi3_clkctrl = 0x4a009500,
+	.cm_l4per_mcspi4_clkctrl = 0x4a009508,
+	.cm_l4per_gpio7_clkctrl = 0x4a009510,
+	.cm_l4per_gpio8_clkctrl = 0x4a009518,
+	.cm_l4per_mmcsd3_clkctrl = 0x4a009520,
+	.cm_l4per_mmcsd4_clkctrl = 0x4a009528,
+	.cm_l4per_msprohg_clkctrl = 0x4a009530,
+	.cm_l4per_slimbus2_clkctrl = 0x4a009538,
+	.cm_l4per_uart1_clkctrl = 0x4a009540,
+	.cm_l4per_uart2_clkctrl = 0x4a009548,
+	.cm_l4per_uart3_clkctrl = 0x4a009550,
+	.cm_l4per_uart4_clkctrl = 0x4a009558,
+	.cm_l4per_mmcsd5_clkctrl = 0x4a009560,
+	.cm_l4per_i2c5_clkctrl = 0x4a009568,
+	.cm_l4per_uart5_clkctrl = 0x4a009570,
+	.cm_l4per_uart6_clkctrl = 0x4a009578,
+	.cm_l4sec_clkstctrl = 0x4a009580,
+	.cm_l4sec_staticdep = 0x4a009584,
+	.cm_l4sec_dynamicdep = 0x4a009588,
+	.cm_l4sec_aes1_clkctrl = 0x4a0095a0,
+	.cm_l4sec_aes2_clkctrl = 0x4a0095a8,
+	.cm_l4sec_des3des_clkctrl = 0x4a0095b0,
+	.cm_l4sec_pkaeip29_clkctrl = 0x4a0095b8,
+	.cm_l4sec_rng_clkctrl = 0x4a0095c0,
+	.cm_l4sec_sha2md51_clkctrl = 0x4a0095c8,
+	.cm_l4sec_cryptodma_clkctrl = 0x4a0095d8,
+
+	/* l4 wkup regs */
+	.cm_abe_pll_ref_clksel = 0x4ae0610c,
+	.cm_sys_clksel = 0x4ae06110,
+	.cm_wkup_clkstctrl = 0x4ae07800,
+	.cm_wkup_l4wkup_clkctrl = 0x4ae07820,
+	.cm_wkup_wdtimer1_clkctrl = 0x4ae07828,
+	.cm_wkup_wdtimer2_clkctrl = 0x4ae07830,
+	.cm_wkup_gpio1_clkctrl = 0x4ae07838,
+	.cm_wkup_gptimer1_clkctrl = 0x4ae07840,
+	.cm_wkup_gptimer12_clkctrl = 0x4ae07848,
+	.cm_wkup_synctimer_clkctrl = 0x4ae07850,
+	.cm_wkup_usim_clkctrl = 0x4ae07858,
+	.cm_wkup_sarram_clkctrl = 0x4ae07860,
+	.cm_wkup_keyboard_clkctrl = 0x4ae07878,
+	.cm_wkup_rtc_clkctrl = 0x4ae07880,
+	.cm_wkup_bandgap_clkctrl = 0x4ae07888,
+	.cm_wkupaon_scrm_clkctrl = 0x4ae07890,
+	.cm_wkupaon_io_srcomp_clkctrl = 0x4ae07898,
+	.prm_rstctrl = 0x4ae07b00,
+	.prm_rstst = 0x4ae07b04,
+	.prm_rsttime = 0x4ae07b08,
+	.prm_vc_val_bypass = 0x4ae07ba0,
+	.prm_vc_cfg_i2c_mode = 0x4ae07bb4,
+	.prm_vc_cfg_i2c_clk = 0x4ae07bb8,
+
+	/* SCRM stuff, used by some boards */
+	.scrm_auxclk0 = 0x4ae0a310,
+	.scrm_auxclk1 = 0x4ae0a314,
+};
+
+struct omap_sys_ctrl_regs const omap5_ctrl = {
+	.control_status				= 0x4A002134,
+	.control_std_fuse_die_id_0		= 0x4A002200,
+	.control_std_fuse_die_id_1		= 0x4A002208,
+	.control_std_fuse_die_id_2		= 0x4A00220C,
+	.control_std_fuse_die_id_3		= 0x4A002210,
+	.control_phy_power_usb 			= 0x4A002370,
+	.control_phy_power_sata			= 0x4A002374,
+	.control_padconf_core_base		= 0x4A002800,
+	.control_paconf_global			= 0x4A002DA0,
+	.control_paconf_mode			= 0x4A002DA4,
+	.control_smart1io_padconf_0		= 0x4A002DA8,
+	.control_smart1io_padconf_1		= 0x4A002DAC,
+	.control_smart1io_padconf_2		= 0x4A002DB0,
+	.control_smart2io_padconf_0		= 0x4A002DB4,
+	.control_smart2io_padconf_1		= 0x4A002DB8,
+	.control_smart2io_padconf_2		= 0x4A002DBC,
+	.control_smart3io_padconf_0		= 0x4A002DC0,
+	.control_smart3io_padconf_1		= 0x4A002DC4,
+	.control_pbias				= 0x4A002E00,
+	.control_i2c_0				= 0x4A002E04,
+	.control_camera_rx			= 0x4A002E08,
+	.control_hdmi_tx_phy			= 0x4A002E0C,
+	.control_uniportm			= 0x4A002E10,
+	.control_dsiphy				= 0x4A002E14,
+	.control_mcbsplp			= 0x4A002E18,
+	.control_usb2phycore			= 0x4A002E1C,
+	.control_hdmi_1				= 0x4A002E20,
+	.control_hsi				= 0x4A002E24,
+	.control_ddr3ch1_0			= 0x4A002E30,
+	.control_ddr3ch2_0			= 0x4A002E34,
+	.control_ddrch1_0			= 0x4A002E38,
+	.control_ddrch1_1			= 0x4A002E3C,
+	.control_ddrch2_0			= 0x4A002E40,
+	.control_ddrch2_1			= 0x4A002E44,
+	.control_lpddr2ch1_0			= 0x4A002E48,
+	.control_lpddr2ch1_1			= 0x4A002E4C,
+	.control_ddrio_0			= 0x4A002E50,
+	.control_ddrio_1			= 0x4A002E54,
+	.control_ddrio_2			= 0x4A002E58,
+	.control_hyst_1				= 0x4A002E5C,
+	.control_usbb_hsic_control		= 0x4A002E60,
+	.control_c2c				= 0x4A002E64,
+	.control_core_control_spare_rw		= 0x4A002E68,
+	.control_core_control_spare_r		= 0x4A002E6C,
+	.control_core_control_spare_r_c0	= 0x4A002E70,
+	.control_srcomp_north_side		= 0x4A002E74,
+	.control_srcomp_south_side		= 0x4A002E78,
+	.control_srcomp_east_side		= 0x4A002E7C,
+	.control_srcomp_west_side		= 0x4A002E80,
+	.control_srcomp_code_latch		= 0x4A002E84,
+	.control_port_emif1_sdram_config	= 0x4AE0C110,
+	.control_port_emif1_lpddr2_nvm_config	= 0x4AE0C114,
+	.control_port_emif2_sdram_config	= 0x4AE0C118,
+	.control_emif1_sdram_config_ext		= 0x4AE0C144,
+	.control_emif2_sdram_config_ext		= 0x4AE0C148,
+	.control_wkup_ldovbb_mpu_voltage_ctrl	= 0x4AE0C318,
+	.control_wkup_ldovbb_mm_voltage_ctrl	= 0x4AE0C314,
+	.control_padconf_wkup_base		= 0x4AE0C800,
+	.control_smart1nopmio_padconf_0		= 0x4AE0CDA0,
+	.control_smart1nopmio_padconf_1		= 0x4AE0CDA4,
+	.control_padconf_mode			= 0x4AE0CDA8,
+	.control_xtal_oscillator		= 0x4AE0CDAC,
+	.control_i2c_2				= 0x4AE0CDB0,
+	.control_ckobuffer			= 0x4AE0CDB4,
+	.control_wkup_control_spare_rw		= 0x4AE0CDB8,
+	.control_wkup_control_spare_r		= 0x4AE0CDBC,
+	.control_wkup_control_spare_r_c0	= 0x4AE0CDC0,
+	.control_srcomp_east_side_wkup		= 0x4AE0CDC4,
+	.control_efuse_1			= 0x4AE0CDC8,
+	.control_efuse_2			= 0x4AE0CDCC,
+	.control_efuse_3			= 0x4AE0CDD0,
+	.control_efuse_4			= 0x4AE0CDD4,
+	.control_efuse_5			= 0x4AE0CDD8,
+	.control_efuse_6			= 0x4AE0CDDC,
+	.control_efuse_7			= 0x4AE0CDE0,
+	.control_efuse_8			= 0x4AE0CDE4,
+	.control_efuse_9			= 0x4AE0CDE8,
+	.control_efuse_10			= 0x4AE0CDEC,
+	.control_efuse_11			= 0x4AE0CDF0,
+	.control_efuse_12			= 0x4AE0CDF4,
+	.control_efuse_13			= 0x4AE0CDF8,
+};
+
+struct omap_sys_ctrl_regs const dra7xx_ctrl = {
+	.control_status				= 0x4A002134,
+	.control_phy_power_usb			= 0x4A002370,
+	.control_phy_power_sata			= 0x4A002374,
+	.ctrl_core_sma_sw_0			= 0x4A0023FC,
+	.ctrl_core_sma_sw_1			= 0x4A002534,
+	.control_core_mac_id_0_lo		= 0x4A002514,
+	.control_core_mac_id_0_hi		= 0x4A002518,
+	.control_core_mac_id_1_lo		= 0x4A00251C,
+	.control_core_mac_id_1_hi		= 0x4A002520,
+	.control_core_mmr_lock1			= 0x4A002540,
+	.control_core_mmr_lock2			= 0x4A002544,
+	.control_core_mmr_lock3			= 0x4A002548,
+	.control_core_mmr_lock4			= 0x4A00254C,
+	.control_core_mmr_lock5			= 0x4A002550,
+	.control_core_control_io1		= 0x4A002554,
+	.control_core_control_io2		= 0x4A002558,
+	.control_paconf_global			= 0x4A002DA0,
+	.control_paconf_mode			= 0x4A002DA4,
+	.control_smart1io_padconf_0		= 0x4A002DA8,
+	.control_smart1io_padconf_1		= 0x4A002DAC,
+	.control_smart1io_padconf_2		= 0x4A002DB0,
+	.control_smart2io_padconf_0		= 0x4A002DB4,
+	.control_smart2io_padconf_1		= 0x4A002DB8,
+	.control_smart2io_padconf_2		= 0x4A002DBC,
+	.control_smart3io_padconf_0		= 0x4A002DC0,
+	.control_smart3io_padconf_1		= 0x4A002DC4,
+	.control_pbias				= 0x4A002E00,
+	.control_i2c_0				= 0x4A002E04,
+	.control_camera_rx			= 0x4A002E08,
+	.control_hdmi_tx_phy			= 0x4A002E0C,
+	.control_uniportm			= 0x4A002E10,
+	.control_dsiphy				= 0x4A002E14,
+	.control_mcbsplp			= 0x4A002E18,
+	.control_usb2phycore			= 0x4A002E1C,
+	.control_hdmi_1				= 0x4A002E20,
+	.control_hsi				= 0x4A002E24,
+	.control_ddr3ch1_0			= 0x4A002E30,
+	.control_ddr3ch2_0			= 0x4A002E34,
+	.control_ddrch1_0			= 0x4A002E38,
+	.control_ddrch1_1			= 0x4A002E3C,
+	.control_ddrch2_0			= 0x4A002E40,
+	.control_ddrch2_1			= 0x4A002E44,
+	.control_lpddr2ch1_0			= 0x4A002E48,
+	.control_lpddr2ch1_1			= 0x4A002E4C,
+	.control_ddrio_0			= 0x4A002E50,
+	.control_ddrio_1			= 0x4A002E54,
+	.control_ddrio_2			= 0x4A002E58,
+	.control_hyst_1				= 0x4A002E5C,
+	.control_usbb_hsic_control		= 0x4A002E60,
+	.control_c2c				= 0x4A002E64,
+	.control_core_control_spare_rw		= 0x4A002E68,
+	.control_core_control_spare_r		= 0x4A002E6C,
+	.control_core_control_spare_r_c0	= 0x4A002E70,
+	.control_srcomp_north_side		= 0x4A002E74,
+	.control_srcomp_south_side		= 0x4A002E78,
+	.control_srcomp_east_side		= 0x4A002E7C,
+	.control_srcomp_west_side		= 0x4A002E80,
+	.control_srcomp_code_latch		= 0x4A002E84,
+	.control_ddr_control_ext_0		= 0x4A002E88,
+	.control_padconf_core_base		= 0x4A003400,
+	.control_port_emif1_sdram_config	= 0x4AE0C110,
+	.control_port_emif1_lpddr2_nvm_config	= 0x4AE0C114,
+	.control_port_emif2_sdram_config	= 0x4AE0C118,
+	.control_emif1_sdram_config_ext		= 0x4AE0C144,
+	.control_emif2_sdram_config_ext		= 0x4AE0C148,
+	.control_wkup_ldovbb_mpu_voltage_ctrl	= 0x4AE0C158,
+	.control_wkup_ldovbb_iva_voltage_ctrl	= 0x4A002470,
+	.control_wkup_ldovbb_eve_voltage_ctrl	= 0x4A00246C,
+	.control_wkup_ldovbb_gpu_voltage_ctrl	= 0x4AE0C154,
+	.control_std_fuse_die_id_0		= 0x4AE0C200,
+	.control_std_fuse_die_id_1		= 0x4AE0C208,
+	.control_std_fuse_die_id_2		= 0x4AE0C20C,
+	.control_std_fuse_die_id_3		= 0x4AE0C210,
+	.control_padconf_mode			= 0x4AE0C5A0,
+	.control_xtal_oscillator		= 0x4AE0C5A4,
+	.control_i2c_2				= 0x4AE0C5A8,
+	.control_ckobuffer			= 0x4AE0C5AC,
+	.control_wkup_control_spare_rw		= 0x4AE0C5B0,
+	.control_wkup_control_spare_r		= 0x4AE0C5B4,
+	.control_wkup_control_spare_r_c0	= 0x4AE0C5B8,
+	.control_srcomp_east_side_wkup		= 0x4AE0C5BC,
+	.control_efuse_1			= 0x4AE0C5C8,
+	.control_efuse_2			= 0x4AE0C5CC,
+	.control_efuse_3			= 0x4AE0C5D0,
+	.control_efuse_4			= 0x4AE0C5D4,
+	.control_efuse_13			= 0x4AE0C5F0,
+	.iodelay_config_base			= 0x4844A000,
+};
+
+struct prcm_regs const omap5_es2_prcm = {
+	/* cm1.ckgen */
+	.cm_clksel_core = 0x4a004100,
+	.cm_clksel_abe = 0x4a004108,
+	.cm_dll_ctrl = 0x4a004110,
+	.cm_clkmode_dpll_core = 0x4a004120,
+	.cm_idlest_dpll_core = 0x4a004124,
+	.cm_autoidle_dpll_core = 0x4a004128,
+	.cm_clksel_dpll_core = 0x4a00412c,
+	.cm_div_m2_dpll_core = 0x4a004130,
+	.cm_div_m3_dpll_core = 0x4a004134,
+	.cm_div_h11_dpll_core = 0x4a004138,
+	.cm_div_h12_dpll_core = 0x4a00413c,
+	.cm_div_h13_dpll_core = 0x4a004140,
+	.cm_div_h14_dpll_core = 0x4a004144,
+	.cm_ssc_deltamstep_dpll_core = 0x4a004148,
+	.cm_ssc_modfreqdiv_dpll_core = 0x4a00414c,
+	.cm_div_h21_dpll_core = 0x4a004150,
+	.cm_div_h22_dpllcore = 0x4a004154,
+	.cm_div_h23_dpll_core = 0x4a004158,
+	.cm_div_h24_dpll_core = 0x4a00415c,
+	.cm_clkmode_dpll_mpu = 0x4a004160,
+	.cm_idlest_dpll_mpu = 0x4a004164,
+	.cm_autoidle_dpll_mpu = 0x4a004168,
+	.cm_clksel_dpll_mpu = 0x4a00416c,
+	.cm_div_m2_dpll_mpu = 0x4a004170,
+	.cm_ssc_deltamstep_dpll_mpu = 0x4a004188,
+	.cm_ssc_modfreqdiv_dpll_mpu = 0x4a00418c,
+	.cm_bypclk_dpll_mpu = 0x4a00419c,
+	.cm_clkmode_dpll_iva = 0x4a0041a0,
+	.cm_idlest_dpll_iva = 0x4a0041a4,
+	.cm_autoidle_dpll_iva = 0x4a0041a8,
+	.cm_clksel_dpll_iva = 0x4a0041ac,
+	.cm_div_h11_dpll_iva = 0x4a0041b8,
+	.cm_div_h12_dpll_iva = 0x4a0041bc,
+	.cm_ssc_deltamstep_dpll_iva = 0x4a0041c8,
+	.cm_ssc_modfreqdiv_dpll_iva = 0x4a0041cc,
+	.cm_bypclk_dpll_iva = 0x4a0041dc,
+	.cm_clkmode_dpll_abe = 0x4a0041e0,
+	.cm_idlest_dpll_abe = 0x4a0041e4,
+	.cm_autoidle_dpll_abe = 0x4a0041e8,
+	.cm_clksel_dpll_abe = 0x4a0041ec,
+	.cm_div_m2_dpll_abe = 0x4a0041f0,
+	.cm_div_m3_dpll_abe = 0x4a0041f4,
+	.cm_ssc_deltamstep_dpll_abe = 0x4a004208,
+	.cm_ssc_modfreqdiv_dpll_abe = 0x4a00420c,
+	.cm_clkmode_dpll_ddrphy = 0x4a004220,
+	.cm_idlest_dpll_ddrphy = 0x4a004224,
+	.cm_autoidle_dpll_ddrphy = 0x4a004228,
+	.cm_clksel_dpll_ddrphy = 0x4a00422c,
+	.cm_div_m2_dpll_ddrphy = 0x4a004230,
+	.cm_div_h11_dpll_ddrphy = 0x4a004238,
+	.cm_div_h12_dpll_ddrphy = 0x4a00423c,
+	.cm_div_h13_dpll_ddrphy = 0x4a004240,
+	.cm_ssc_deltamstep_dpll_ddrphy = 0x4a004248,
+	.cm_shadow_freq_config1 = 0x4a004260,
+	.cm_mpu_mpu_clkctrl = 0x4a004320,
+
+	/* cm1.dsp */
+	.cm_dsp_clkstctrl = 0x4a004400,
+	.cm_dsp_dsp_clkctrl = 0x4a004420,
+
+	/* cm1.abe */
+	.cm1_abe_clkstctrl = 0x4a004500,
+	.cm1_abe_l4abe_clkctrl = 0x4a004520,
+	.cm1_abe_aess_clkctrl = 0x4a004528,
+	.cm1_abe_pdm_clkctrl = 0x4a004530,
+	.cm1_abe_dmic_clkctrl = 0x4a004538,
+	.cm1_abe_mcasp_clkctrl = 0x4a004540,
+	.cm1_abe_mcbsp1_clkctrl = 0x4a004548,
+	.cm1_abe_mcbsp2_clkctrl = 0x4a004550,
+	.cm1_abe_mcbsp3_clkctrl = 0x4a004558,
+	.cm1_abe_slimbus_clkctrl = 0x4a004560,
+	.cm1_abe_timer5_clkctrl = 0x4a004568,
+	.cm1_abe_timer6_clkctrl = 0x4a004570,
+	.cm1_abe_timer7_clkctrl = 0x4a004578,
+	.cm1_abe_timer8_clkctrl = 0x4a004580,
+	.cm1_abe_wdt3_clkctrl = 0x4a004588,
+
+	/* cm2.ckgen */
+	.cm_clksel_mpu_m3_iss_root = 0x4a008100,
+	.cm_clksel_usb_60mhz = 0x4a008104,
+	.cm_scale_fclk = 0x4a008108,
+	.cm_core_dvfs_perf1 = 0x4a008110,
+	.cm_core_dvfs_perf2 = 0x4a008114,
+	.cm_core_dvfs_perf3 = 0x4a008118,
+	.cm_core_dvfs_perf4 = 0x4a00811c,
+	.cm_core_dvfs_current = 0x4a008124,
+	.cm_iva_dvfs_perf_tesla = 0x4a008128,
+	.cm_iva_dvfs_perf_ivahd = 0x4a00812c,
+	.cm_iva_dvfs_perf_abe = 0x4a008130,
+	.cm_iva_dvfs_current = 0x4a008138,
+	.cm_clkmode_dpll_per = 0x4a008140,
+	.cm_idlest_dpll_per = 0x4a008144,
+	.cm_autoidle_dpll_per = 0x4a008148,
+	.cm_clksel_dpll_per = 0x4a00814c,
+	.cm_div_m2_dpll_per = 0x4a008150,
+	.cm_div_m3_dpll_per = 0x4a008154,
+	.cm_div_h11_dpll_per = 0x4a008158,
+	.cm_div_h12_dpll_per = 0x4a00815c,
+	.cm_div_h13_dpll_per = 0x4a008160,
+	.cm_div_h14_dpll_per = 0x4a008164,
+	.cm_ssc_deltamstep_dpll_per = 0x4a008168,
+	.cm_ssc_modfreqdiv_dpll_per = 0x4a00816c,
+	.cm_emu_override_dpll_per = 0x4a008170,
+	.cm_clkmode_dpll_usb = 0x4a008180,
+	.cm_idlest_dpll_usb = 0x4a008184,
+	.cm_autoidle_dpll_usb = 0x4a008188,
+	.cm_clksel_dpll_usb = 0x4a00818c,
+	.cm_div_m2_dpll_usb = 0x4a008190,
+	.cm_ssc_deltamstep_dpll_usb = 0x4a0081a8,
+	.cm_ssc_modfreqdiv_dpll_usb = 0x4a0081ac,
+	.cm_clkdcoldo_dpll_usb = 0x4a0081b4,
+	.cm_clkmode_dpll_unipro = 0x4a0081c0,
+	.cm_idlest_dpll_unipro = 0x4a0081c4,
+	.cm_autoidle_dpll_unipro = 0x4a0081c8,
+	.cm_clksel_dpll_unipro = 0x4a0081cc,
+	.cm_div_m2_dpll_unipro = 0x4a0081d0,
+	.cm_ssc_deltamstep_dpll_unipro = 0x4a0081e8,
+	.cm_ssc_modfreqdiv_dpll_unipro = 0x4a0081ec,
+	.cm_coreaon_usb_phy1_core_clkctrl = 0x4A008640,
+	.cm_coreaon_bandgap_clkctrl = 0x4a008648,
+	.cm_coreaon_io_srcomp_clkctrl = 0x4a008650,
+
+	/* cm2.core */
+	.cm_l3_1_clkstctrl = 0x4a008700,
+	.cm_l3_1_dynamicdep = 0x4a008708,
+	.cm_l3_1_l3_1_clkctrl = 0x4a008720,
+	.cm_l3_2_clkstctrl = 0x4a008800,
+	.cm_l3_2_dynamicdep = 0x4a008808,
+	.cm_l3_2_l3_2_clkctrl = 0x4a008820,
+	.cm_l3_gpmc_clkctrl = 0x4a008828,
+	.cm_l3_2_ocmc_ram_clkctrl = 0x4a008830,
+	.cm_mpu_m3_clkstctrl = 0x4a008900,
+	.cm_mpu_m3_staticdep = 0x4a008904,
+	.cm_mpu_m3_dynamicdep = 0x4a008908,
+	.cm_mpu_m3_mpu_m3_clkctrl = 0x4a008920,
+	.cm_sdma_clkstctrl = 0x4a008a00,
+	.cm_sdma_staticdep = 0x4a008a04,
+	.cm_sdma_dynamicdep = 0x4a008a08,
+	.cm_sdma_sdma_clkctrl = 0x4a008a20,
+	.cm_memif_clkstctrl = 0x4a008b00,
+	.cm_memif_dmm_clkctrl = 0x4a008b20,
+	.cm_memif_emif_fw_clkctrl = 0x4a008b28,
+	.cm_memif_emif_1_clkctrl = 0x4a008b30,
+	.cm_memif_emif_2_clkctrl = 0x4a008b38,
+	.cm_memif_dll_clkctrl = 0x4a008b40,
+	.cm_memif_emif_h1_clkctrl = 0x4a008b50,
+	.cm_memif_emif_h2_clkctrl = 0x4a008b58,
+	.cm_memif_dll_h_clkctrl = 0x4a008b60,
+	.cm_c2c_clkstctrl = 0x4a008c00,
+	.cm_c2c_staticdep = 0x4a008c04,
+	.cm_c2c_dynamicdep = 0x4a008c08,
+	.cm_c2c_sad2d_clkctrl = 0x4a008c20,
+	.cm_c2c_modem_icr_clkctrl = 0x4a008c28,
+	.cm_c2c_sad2d_fw_clkctrl = 0x4a008c30,
+	.cm_l4cfg_clkstctrl = 0x4a008d00,
+	.cm_l4cfg_dynamicdep = 0x4a008d08,
+	.cm_l4cfg_l4_cfg_clkctrl = 0x4a008d20,
+	.cm_l4cfg_hw_sem_clkctrl = 0x4a008d28,
+	.cm_l4cfg_mailbox_clkctrl = 0x4a008d30,
+	.cm_l4cfg_sar_rom_clkctrl = 0x4a008d38,
+	.cm_l3instr_clkstctrl = 0x4a008e00,
+	.cm_l3instr_l3_3_clkctrl = 0x4a008e20,
+	.cm_l3instr_l3_instr_clkctrl = 0x4a008e28,
+	.cm_l3instr_intrconn_wp1_clkctrl = 0x4a008e40,
+	.cm_l4per_clkstctrl = 0x4a009000,
+	.cm_l4per_dynamicdep = 0x4a009008,
+	.cm_l4per_adc_clkctrl = 0x4a009020,
+	.cm_l4per_gptimer10_clkctrl = 0x4a009028,
+	.cm_l4per_gptimer11_clkctrl = 0x4a009030,
+	.cm_l4per_gptimer2_clkctrl = 0x4a009038,
+	.cm_l4per_gptimer3_clkctrl = 0x4a009040,
+	.cm_l4per_gptimer4_clkctrl = 0x4a009048,
+	.cm_l4per_gptimer9_clkctrl = 0x4a009050,
+	.cm_l4per_elm_clkctrl = 0x4a009058,
+	.cm_l4per_gpio2_clkctrl = 0x4a009060,
+	.cm_l4per_gpio3_clkctrl = 0x4a009068,
+	.cm_l4per_gpio4_clkctrl = 0x4a009070,
+	.cm_l4per_gpio5_clkctrl = 0x4a009078,
+	.cm_l4per_gpio6_clkctrl = 0x4a009080,
+	.cm_l4per_hdq1w_clkctrl = 0x4a009088,
+	.cm_l4per_hecc1_clkctrl = 0x4a009090,
+	.cm_l4per_hecc2_clkctrl = 0x4a009098,
+	.cm_l4per_i2c1_clkctrl = 0x4a0090a0,
+	.cm_l4per_i2c2_clkctrl = 0x4a0090a8,
+	.cm_l4per_i2c3_clkctrl = 0x4a0090b0,
+	.cm_l4per_i2c4_clkctrl = 0x4a0090b8,
+	.cm_l4per_l4per_clkctrl = 0x4a0090c0,
+	.cm_l4per_mcasp2_clkctrl = 0x4a0090d0,
+	.cm_l4per_mcasp3_clkctrl = 0x4a0090d8,
+	.cm_l4per_mgate_clkctrl = 0x4a0090e8,
+	.cm_l4per_mcspi1_clkctrl = 0x4a0090f0,
+	.cm_l4per_mcspi2_clkctrl = 0x4a0090f8,
+	.cm_l4per_mcspi3_clkctrl = 0x4a009100,
+	.cm_l4per_mcspi4_clkctrl = 0x4a009108,
+	.cm_l4per_gpio7_clkctrl = 0x4a009110,
+	.cm_l4per_gpio8_clkctrl = 0x4a009118,
+	.cm_l4per_mmcsd3_clkctrl = 0x4a009120,
+	.cm_l4per_mmcsd4_clkctrl = 0x4a009128,
+	.cm_l4per_msprohg_clkctrl = 0x4a009130,
+	.cm_l4per_slimbus2_clkctrl = 0x4a009138,
+	.cm_l4per_uart1_clkctrl = 0x4a009140,
+	.cm_l4per_uart2_clkctrl = 0x4a009148,
+	.cm_l4per_uart3_clkctrl = 0x4a009150,
+	.cm_l4per_uart4_clkctrl = 0x4a009158,
+	.cm_l4per_mmcsd5_clkctrl = 0x4a009160,
+	.cm_l4per_i2c5_clkctrl = 0x4a009168,
+	.cm_l4per_uart5_clkctrl = 0x4a009170,
+	.cm_l4per_uart6_clkctrl = 0x4a009178,
+	.cm_l4sec_clkstctrl = 0x4a009180,
+	.cm_l4sec_staticdep = 0x4a009184,
+	.cm_l4sec_dynamicdep = 0x4a009188,
+	.cm_l4sec_aes1_clkctrl = 0x4a0091a0,
+	.cm_l4sec_aes2_clkctrl = 0x4a0091a8,
+	.cm_l4sec_des3des_clkctrl = 0x4a0091b0,
+	.cm_l4sec_pkaeip29_clkctrl = 0x4a0091b8,
+	.cm_l4sec_rng_clkctrl = 0x4a0091c0,
+	.cm_l4sec_sha2md51_clkctrl = 0x4a0091c8,
+	.cm_l4sec_cryptodma_clkctrl = 0x4a0091d8,
+
+	/* cm2.ivahd */
+	.cm_ivahd_clkstctrl = 0x4a009200,
+	.cm_ivahd_ivahd_clkctrl = 0x4a009220,
+	.cm_ivahd_sl2_clkctrl = 0x4a009228,
+
+	/* cm2.cam */
+	.cm_cam_clkstctrl = 0x4a009300,
+	.cm_cam_iss_clkctrl = 0x4a009320,
+	.cm_cam_fdif_clkctrl = 0x4a009328,
+
+	/* cm2.dss */
+	.cm_dss_clkstctrl = 0x4a009400,
+	.cm_dss_dss_clkctrl = 0x4a009420,
+
+	/* cm2.sgx */
+	.cm_sgx_clkstctrl = 0x4a009500,
+	.cm_sgx_sgx_clkctrl = 0x4a009520,
+
+	/* cm2.l3init */
+	.cm_l3init_clkstctrl = 0x4a009600,
+
+	/* cm2.l3init */
+	.cm_l3init_hsmmc1_clkctrl = 0x4a009628,
+	.cm_l3init_hsmmc2_clkctrl = 0x4a009630,
+	.cm_l3init_hsi_clkctrl = 0x4a009638,
+	.cm_l3init_hsusbhost_clkctrl = 0x4a009658,
+	.cm_l3init_hsusbotg_clkctrl = 0x4a009660,
+	.cm_l3init_hsusbtll_clkctrl = 0x4a009668,
+	.cm_l3init_p1500_clkctrl = 0x4a009678,
+	.cm_l3init_sata_clkctrl = 0x4a009688,
+	.cm_l3init_fsusb_clkctrl = 0x4a0096d0,
+	.cm_l3init_ocp2scp1_clkctrl = 0x4a0096e0,
+	.cm_l3init_ocp2scp3_clkctrl = 0x4a0096e8,
+	.cm_l3init_usb_otg_ss1_clkctrl = 0x4a0096f0,
+
+	/* prm irqstatus regs */
+	.prm_irqstatus_mpu = 0x4ae06010,
+	.prm_irqstatus_mpu_2 = 0x4ae06014,
+
+	/* l4 wkup regs */
+	.cm_abe_pll_ref_clksel = 0x4ae0610c,
+	.cm_sys_clksel = 0x4ae06110,
+	.cm_wkup_clkstctrl = 0x4ae07900,
+	.cm_wkup_l4wkup_clkctrl = 0x4ae07920,
+	.cm_wkup_wdtimer1_clkctrl = 0x4ae07928,
+	.cm_wkup_wdtimer2_clkctrl = 0x4ae07930,
+	.cm_wkup_gpio1_clkctrl = 0x4ae07938,
+	.cm_wkup_gptimer1_clkctrl = 0x4ae07940,
+	.cm_wkup_gptimer12_clkctrl = 0x4ae07948,
+	.cm_wkup_synctimer_clkctrl = 0x4ae07950,
+	.cm_wkup_usim_clkctrl = 0x4ae07958,
+	.cm_wkup_sarram_clkctrl = 0x4ae07960,
+	.cm_wkup_keyboard_clkctrl = 0x4ae07978,
+	.cm_wkup_rtc_clkctrl = 0x4ae07980,
+	.cm_wkup_bandgap_clkctrl = 0x4ae07988,
+	.cm_wkupaon_scrm_clkctrl = 0x4ae07990,
+	.cm_wkupaon_io_srcomp_clkctrl = 0x4ae07998,
+	.prm_rstctrl = 0x4ae07c00,
+	.prm_rstst = 0x4ae07c04,
+	.prm_rsttime = 0x4ae07c08,
+	.prm_vc_val_bypass = 0x4ae07ca0,
+	.prm_vc_cfg_i2c_mode = 0x4ae07cb4,
+	.prm_vc_cfg_i2c_clk = 0x4ae07cb8,
+
+	.prm_abbldo_mpu_setup = 0x4ae07cdc,
+	.prm_abbldo_mpu_ctrl = 0x4ae07ce0,
+	.prm_abbldo_mm_setup = 0x4ae07ce4,
+	.prm_abbldo_mm_ctrl = 0x4ae07ce8,
+
+	/* SCRM stuff, used by some boards */
+	.scrm_auxclk0 = 0x4ae0a310,
+	.scrm_auxclk1 = 0x4ae0a314,
+};
+
+struct prcm_regs const dra7xx_prcm = {
+	/* cm1.ckgen */
+	.cm_clksel_core				= 0x4a005100,
+	.cm_clksel_abe				= 0x4a005108,
+	.cm_dll_ctrl				= 0x4a005110,
+	.cm_clkmode_dpll_core			= 0x4a005120,
+	.cm_idlest_dpll_core			= 0x4a005124,
+	.cm_autoidle_dpll_core			= 0x4a005128,
+	.cm_clksel_dpll_core			= 0x4a00512c,
+	.cm_div_m2_dpll_core			= 0x4a005130,
+	.cm_div_m3_dpll_core			= 0x4a005134,
+	.cm_div_h11_dpll_core			= 0x4a005138,
+	.cm_div_h12_dpll_core			= 0x4a00513c,
+	.cm_div_h13_dpll_core			= 0x4a005140,
+	.cm_div_h14_dpll_core			= 0x4a005144,
+	.cm_ssc_deltamstep_dpll_core		= 0x4a005148,
+	.cm_ssc_modfreqdiv_dpll_core		= 0x4a00514c,
+	.cm_div_h21_dpll_core			= 0x4a005150,
+	.cm_div_h22_dpllcore			= 0x4a005154,
+	.cm_div_h23_dpll_core			= 0x4a005158,
+	.cm_div_h24_dpll_core			= 0x4a00515c,
+	.cm_clkmode_dpll_mpu			= 0x4a005160,
+	.cm_idlest_dpll_mpu			= 0x4a005164,
+	.cm_autoidle_dpll_mpu			= 0x4a005168,
+	.cm_clksel_dpll_mpu			= 0x4a00516c,
+	.cm_div_m2_dpll_mpu			= 0x4a005170,
+	.cm_ssc_deltamstep_dpll_mpu		= 0x4a005188,
+	.cm_ssc_modfreqdiv_dpll_mpu		= 0x4a00518c,
+	.cm_bypclk_dpll_mpu			= 0x4a00519c,
+	.cm_clkmode_dpll_iva			= 0x4a0051a0,
+	.cm_idlest_dpll_iva			= 0x4a0051a4,
+	.cm_autoidle_dpll_iva			= 0x4a0051a8,
+	.cm_clksel_dpll_iva			= 0x4a0051ac,
+	.cm_ssc_deltamstep_dpll_iva		= 0x4a0051c8,
+	.cm_ssc_modfreqdiv_dpll_iva		= 0x4a0051cc,
+	.cm_bypclk_dpll_iva			= 0x4a0051dc,
+	.cm_clkmode_dpll_abe			= 0x4a0051e0,
+	.cm_idlest_dpll_abe			= 0x4a0051e4,
+	.cm_autoidle_dpll_abe			= 0x4a0051e8,
+	.cm_clksel_dpll_abe			= 0x4a0051ec,
+	.cm_div_m2_dpll_abe			= 0x4a0051f0,
+	.cm_div_m3_dpll_abe			= 0x4a0051f4,
+	.cm_ssc_deltamstep_dpll_abe		= 0x4a005208,
+	.cm_ssc_modfreqdiv_dpll_abe		= 0x4a00520c,
+	.cm_clkmode_dpll_ddrphy			= 0x4a005210,
+	.cm_idlest_dpll_ddrphy			= 0x4a005214,
+	.cm_autoidle_dpll_ddrphy		= 0x4a005218,
+	.cm_clksel_dpll_ddrphy			= 0x4a00521c,
+	.cm_div_m2_dpll_ddrphy			= 0x4a005220,
+	.cm_div_h11_dpll_ddrphy			= 0x4a005228,
+	.cm_ssc_deltamstep_dpll_ddrphy		= 0x4a00522c,
+	.cm_clkmode_dpll_dsp			= 0x4a005234,
+	.cm_shadow_freq_config1			= 0x4a005260,
+	.cm_clkmode_dpll_gmac			= 0x4a0052a8,
+	.cm_coreaon_usb_phy1_core_clkctrl	= 0x4a008640,
+	.cm_coreaon_usb_phy2_core_clkctrl	= 0x4a008688,
+	.cm_coreaon_usb_phy3_core_clkctrl	= 0x4a008698,
+	.cm_coreaon_l3init_60m_gfclk_clkctrl	= 0x4a0086c0,
+
+	/* cm1.mpu */
+	.cm_mpu_mpu_clkctrl			= 0x4a005320,
+
+	/* cm1.dsp */
+	.cm_dsp_clkstctrl			= 0x4a005400,
+	.cm_dsp_dsp_clkctrl			= 0x4a005420,
+
+	/* cm IPU */
+	.cm_ipu_clkstctrl			= 0x4a005540,
+	.cm_ipu_i2c5_clkctrl			= 0x4a005578,
+
+	/* prm irqstatus regs */
+	.prm_irqstatus_mpu			= 0x4ae06010,
+	.prm_irqstatus_mpu_2			= 0x4ae06014,
+
+	/* cm2.ckgen */
+	.cm_clksel_usb_60mhz			= 0x4a008104,
+	.cm_clkmode_dpll_per			= 0x4a008140,
+	.cm_idlest_dpll_per			= 0x4a008144,
+	.cm_autoidle_dpll_per			= 0x4a008148,
+	.cm_clksel_dpll_per			= 0x4a00814c,
+	.cm_div_m2_dpll_per			= 0x4a008150,
+	.cm_div_m3_dpll_per			= 0x4a008154,
+	.cm_div_h11_dpll_per			= 0x4a008158,
+	.cm_div_h12_dpll_per			= 0x4a00815c,
+	.cm_div_h13_dpll_per			= 0x4a008160,
+	.cm_div_h14_dpll_per			= 0x4a008164,
+	.cm_ssc_deltamstep_dpll_per		= 0x4a008168,
+	.cm_ssc_modfreqdiv_dpll_per		= 0x4a00816c,
+	.cm_clkmode_dpll_usb			= 0x4a008180,
+	.cm_idlest_dpll_usb			= 0x4a008184,
+	.cm_autoidle_dpll_usb			= 0x4a008188,
+	.cm_clksel_dpll_usb			= 0x4a00818c,
+	.cm_div_m2_dpll_usb			= 0x4a008190,
+	.cm_ssc_deltamstep_dpll_usb		= 0x4a0081a8,
+	.cm_ssc_modfreqdiv_dpll_usb		= 0x4a0081ac,
+	.cm_clkdcoldo_dpll_usb			= 0x4a0081b4,
+	.cm_clkmode_dpll_pcie_ref		= 0x4a008200,
+	.cm_clkmode_apll_pcie			= 0x4a00821c,
+	.cm_idlest_apll_pcie			= 0x4a008220,
+	.cm_div_m2_apll_pcie			= 0x4a008224,
+	.cm_clkvcoldo_apll_pcie			= 0x4a008228,
+
+	/* cm2.core */
+	.cm_l3_1_clkstctrl			= 0x4a008700,
+	.cm_l3_1_dynamicdep			= 0x4a008708,
+	.cm_l3_1_l3_1_clkctrl			= 0x4a008720,
+	.cm_l3_gpmc_clkctrl			= 0x4a008728,
+	.cm_mpu_m3_clkstctrl			= 0x4a008900,
+	.cm_mpu_m3_staticdep			= 0x4a008904,
+	.cm_mpu_m3_dynamicdep			= 0x4a008908,
+	.cm_mpu_m3_mpu_m3_clkctrl		= 0x4a008920,
+	.cm_sdma_clkstctrl			= 0x4a008a00,
+	.cm_sdma_staticdep			= 0x4a008a04,
+	.cm_sdma_dynamicdep			= 0x4a008a08,
+	.cm_sdma_sdma_clkctrl			= 0x4a008a20,
+	.cm_memif_clkstctrl			= 0x4a008b00,
+	.cm_memif_dmm_clkctrl			= 0x4a008b20,
+	.cm_memif_emif_fw_clkctrl		= 0x4a008b28,
+	.cm_memif_emif_1_clkctrl		= 0x4a008b30,
+	.cm_memif_emif_2_clkctrl		= 0x4a008b38,
+	.cm_memif_dll_clkctrl			= 0x4a008b40,
+	.cm_l4cfg_clkstctrl			= 0x4a008d00,
+	.cm_l4cfg_dynamicdep			= 0x4a008d08,
+	.cm_l4cfg_l4_cfg_clkctrl		= 0x4a008d20,
+	.cm_l4cfg_hw_sem_clkctrl		= 0x4a008d28,
+	.cm_l4cfg_mailbox_clkctrl		= 0x4a008d30,
+	.cm_l4cfg_sar_rom_clkctrl		= 0x4a008d38,
+	.cm_l3instr_clkstctrl			= 0x4a008e00,
+	.cm_l3instr_l3_3_clkctrl		= 0x4a008e20,
+	.cm_l3instr_l3_instr_clkctrl		= 0x4a008e28,
+	.cm_l3instr_intrconn_wp1_clkctrl	= 0x4a008e40,
+
+	/* cm2.ivahd */
+	.cm_ivahd_clkstctrl			= 0x4a008f00,
+	.cm_ivahd_ivahd_clkctrl			= 0x4a008f20,
+	.cm_ivahd_sl2_clkctrl			= 0x4a008f28,
+
+	/* cm2.cam */
+	.cm_cam_clkstctrl			= 0x4a009000,
+	.cm_cam_vip1_clkctrl			= 0x4a009020,
+	.cm_cam_vip2_clkctrl			= 0x4a009028,
+	.cm_cam_vip3_clkctrl			= 0x4a009030,
+	.cm_cam_lvdsrx_clkctrl			= 0x4a009038,
+	.cm_cam_csi1_clkctrl			= 0x4a009040,
+	.cm_cam_csi2_clkctrl			= 0x4a009048,
+
+	/* cm2.dss */
+	.cm_dss_clkstctrl			= 0x4a009100,
+	.cm_dss_dss_clkctrl			= 0x4a009120,
+
+	/* cm2.sgx */
+	.cm_sgx_clkstctrl			= 0x4a009200,
+	.cm_sgx_sgx_clkctrl			= 0x4a009220,
+
+	/* cm2.l3init */
+	.cm_l3init_clkstctrl			= 0x4a009300,
+
+	/* cm2.l3init */
+	.cm_l3init_hsmmc1_clkctrl		= 0x4a009328,
+	.cm_l3init_hsmmc2_clkctrl		= 0x4a009330,
+	.cm_l3init_hsusbhost_clkctrl		= 0x4a009340,
+	.cm_l3init_hsusbotg_clkctrl		= 0x4a009348,
+	.cm_l3init_hsusbtll_clkctrl		= 0x4a009350,
+	.cm_l3init_sata_clkctrl			= 0x4a009388,
+	.cm_gmac_clkstctrl			= 0x4a0093c0,
+	.cm_gmac_gmac_clkctrl			= 0x4a0093d0,
+	.cm_l3init_ocp2scp1_clkctrl		= 0x4a0093e0,
+	.cm_l3init_ocp2scp3_clkctrl		= 0x4a0093e8,
+	.cm_l3init_usb_otg_ss1_clkctrl		= 0x4a0093f0,
+	.cm_l3init_usb_otg_ss2_clkctrl		= 0x4a009340,
+
+	/* cm2.l4per */
+	.cm_l4per_clkstctrl			= 0x4a009700,
+	.cm_l4per_dynamicdep			= 0x4a009708,
+	.cm_l4per_gptimer10_clkctrl		= 0x4a009728,
+	.cm_l4per_gptimer11_clkctrl		= 0x4a009730,
+	.cm_l4per_gptimer2_clkctrl		= 0x4a009738,
+	.cm_l4per_gptimer3_clkctrl		= 0x4a009740,
+	.cm_l4per_gptimer4_clkctrl		= 0x4a009748,
+	.cm_l4per_gptimer9_clkctrl		= 0x4a009750,
+	.cm_l4per_elm_clkctrl			= 0x4a009758,
+	.cm_l4per_gpio2_clkctrl			= 0x4a009760,
+	.cm_l4per_gpio3_clkctrl			= 0x4a009768,
+	.cm_l4per_gpio4_clkctrl			= 0x4a009770,
+	.cm_l4per_gpio5_clkctrl			= 0x4a009778,
+	.cm_l4per_gpio6_clkctrl			= 0x4a009780,
+	.cm_l4per_hdq1w_clkctrl			= 0x4a009788,
+	.cm_l4per_i2c1_clkctrl			= 0x4a0097a0,
+	.cm_l4per_i2c2_clkctrl			= 0x4a0097a8,
+	.cm_l4per_i2c3_clkctrl			= 0x4a0097b0,
+	.cm_l4per_i2c4_clkctrl			= 0x4a0097b8,
+	.cm_l4per_l4per_clkctrl			= 0x4a0097c0,
+	.cm_l4per_mcspi1_clkctrl		= 0x4a0097f0,
+	.cm_l4per_mcspi2_clkctrl		= 0x4a0097f8,
+	.cm_l4per_mcspi3_clkctrl		= 0x4a009800,
+	.cm_l4per_mcspi4_clkctrl		= 0x4a009808,
+	.cm_l4per_gpio7_clkctrl			= 0x4a009810,
+	.cm_l4per_gpio8_clkctrl			= 0x4a009818,
+	.cm_l4per_mmcsd3_clkctrl		= 0x4a009820,
+	.cm_l4per_mmcsd4_clkctrl		= 0x4a009828,
+	.cm_l4per_qspi_clkctrl			= 0x4a009838,
+	.cm_l4per_uart1_clkctrl			= 0x4a009840,
+	.cm_l4per_uart2_clkctrl			= 0x4a009848,
+	.cm_l4per_uart3_clkctrl			= 0x4a009850,
+	.cm_l4per_uart4_clkctrl			= 0x4a009858,
+	.cm_l4per_uart5_clkctrl			= 0x4a009870,
+	.cm_l4sec_clkstctrl			= 0x4a009880,
+	.cm_l4sec_staticdep			= 0x4a009884,
+	.cm_l4sec_dynamicdep			= 0x4a009888,
+	.cm_l4sec_aes1_clkctrl			= 0x4a0098a0,
+	.cm_l4sec_aes2_clkctrl			= 0x4a0098a8,
+	.cm_l4sec_des3des_clkctrl		= 0x4a0098b0,
+	.cm_l4sec_rng_clkctrl			= 0x4a0098c0,
+	.cm_l4sec_sha2md51_clkctrl		= 0x4a0098c8,
+	.cm_l4sec_cryptodma_clkctrl		= 0x4a0098d8,
+
+	/* l4 wkup regs */
+	.cm_abe_pll_ref_clksel			= 0x4ae0610c,
+	.cm_sys_clksel				= 0x4ae06110,
+	.cm_abe_pll_sys_clksel			= 0x4ae06118,
+	.cm_wkup_clkstctrl			= 0x4ae07800,
+	.cm_wkup_l4wkup_clkctrl			= 0x4ae07820,
+	.cm_wkup_wdtimer1_clkctrl		= 0x4ae07828,
+	.cm_wkup_wdtimer2_clkctrl		= 0x4ae07830,
+	.cm_wkup_gpio1_clkctrl			= 0x4ae07838,
+	.cm_wkup_gptimer1_clkctrl		= 0x4ae07840,
+	.cm_wkup_gptimer12_clkctrl		= 0x4ae07848,
+	.cm_wkup_sarram_clkctrl			= 0x4ae07860,
+	.cm_wkup_keyboard_clkctrl		= 0x4ae07878,
+	.cm_wkupaon_scrm_clkctrl		= 0x4ae07890,
+	.prm_rstctrl				= 0x4ae07d00,
+	.prm_rstst				= 0x4ae07d04,
+	.prm_rsttime				= 0x4ae07d08,
+	.prm_io_pmctrl				= 0x4ae07d20,
+	.prm_vc_val_bypass			= 0x4ae07da0,
+	.prm_vc_cfg_i2c_mode			= 0x4ae07db4,
+	.prm_vc_cfg_i2c_clk			= 0x4ae07db8,
+
+	.prm_abbldo_mpu_setup			= 0x4AE07DDC,
+	.prm_abbldo_mpu_ctrl			= 0x4AE07DE0,
+	.prm_abbldo_iva_setup			= 0x4AE07E34,
+	.prm_abbldo_iva_ctrl			= 0x4AE07E24,
+	.prm_abbldo_eve_setup			= 0x4AE07E30,
+	.prm_abbldo_eve_ctrl			= 0x4AE07E20,
+	.prm_abbldo_gpu_setup			= 0x4AE07DE4,
+	.prm_abbldo_gpu_ctrl			= 0x4AE07DE8,
+
+	/*l3main1 edma*/
+	.cm_l3main1_tptc1_clkctrl               = 0x4a008778,
+	.cm_l3main1_tptc2_clkctrl               = 0x4a008780,
+};
+
+void clrset_spare_register(u8 spare_type, u32 clear_bits, u32 set_bits)
+{
+	u32 reg = spare_type ? (*ctrl)->ctrl_core_sma_sw_1 :
+		(*ctrl)->ctrl_core_sma_sw_0;
+	clrsetbits_le32(reg, clear_bits, set_bits);
+}
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/sdram.c b/roms/u-boot/arch/arm/mach-omap2/omap5/sdram.c
new file mode 100644
index 000000000..786da45fa
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/sdram.c
@@ -0,0 +1,750 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Timing and Organization details of the ddr device parts used in OMAP5
+ * EVM
+ *
+ * (C) Copyright 2010
+ * Texas Instruments, <www.ti.com>
+ *
+ * Aneesh V <aneesh@ti.com>
+ * Sricharan R <r.sricharan@ti.com>
+ */
+
+#include <common.h>
+#include <asm/emif.h>
+#include <asm/arch/sys_proto.h>
+
+/*
+ * This file provides details of the LPDDR2 SDRAM parts used on OMAP5
+ * EVM. Since the parts used and geometry are identical for
+ * evm for a given OMAP5 revision, this information is kept
+ * here instead of being in board directory. However the key functions
+ * exported are weakly linked so that they can be over-ridden in the board
+ * directory if there is a OMAP5 board in the future that uses a different
+ * memory device or geometry.
+ *
+ * For any new board with different memory devices over-ride one or more
+ * of the following functions as per the CONFIG flags you intend to enable:
+ * - emif_get_reg_dump()
+ * - emif_get_dmm_regs()
+ * - emif_get_device_details()
+ * - emif_get_device_timings()
+ */
+
+#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
+const struct emif_regs emif_regs_532_mhz_2cs = {
+	.sdram_config_init		= 0x80800EBA,
+	.sdram_config			= 0x808022BA,
+	.ref_ctrl			= 0x0000081A,
+	.sdram_tim1			= 0x772F6873,
+	.sdram_tim2			= 0x304a129a,
+	.sdram_tim3			= 0x02f7e45f,
+	.read_idle_ctrl			= 0x00050000,
+	.zq_config			= 0x000b3215,
+	.temp_alert_config		= 0x08000a05,
+	.emif_ddr_phy_ctlr_1_init	= 0x0E28420d,
+	.emif_ddr_phy_ctlr_1		= 0x0E28420d,
+	.emif_ddr_ext_phy_ctrl_1	= 0x04020080,
+	.emif_ddr_ext_phy_ctrl_2	= 0x28C518A3,
+	.emif_ddr_ext_phy_ctrl_3	= 0x518A3146,
+	.emif_ddr_ext_phy_ctrl_4	= 0x0014628C,
+	.emif_ddr_ext_phy_ctrl_5	= 0x04010040
+};
+
+const struct emif_regs emif_regs_532_mhz_2cs_es2 = {
+	.sdram_config_init		= 0x80800EBA,
+	.sdram_config			= 0x808022BA,
+	.ref_ctrl			= 0x0000081A,
+	.sdram_tim1			= 0x772F6873,
+	.sdram_tim2			= 0x304a129a,
+	.sdram_tim3			= 0x02f7e45f,
+	.read_idle_ctrl			= 0x00050000,
+	.zq_config			= 0x100b3215,
+	.temp_alert_config		= 0x08000a05,
+	.emif_ddr_phy_ctlr_1_init	= 0x0E30400d,
+	.emif_ddr_phy_ctlr_1		= 0x0E30400d,
+	.emif_ddr_ext_phy_ctrl_1	= 0x04020080,
+	.emif_ddr_ext_phy_ctrl_2	= 0x28C518A3,
+	.emif_ddr_ext_phy_ctrl_3	= 0x518A3146,
+	.emif_ddr_ext_phy_ctrl_4	= 0x0014628C,
+	.emif_ddr_ext_phy_ctrl_5	= 0xC330CC33,
+};
+
+const struct emif_regs emif_regs_266_mhz_2cs = {
+	.sdram_config_init		= 0x80800EBA,
+	.sdram_config			= 0x808022BA,
+	.ref_ctrl			= 0x0000040D,
+	.sdram_tim1			= 0x2A86B419,
+	.sdram_tim2			= 0x1025094A,
+	.sdram_tim3			= 0x026BA22F,
+	.read_idle_ctrl			= 0x00050000,
+	.zq_config			= 0x000b3215,
+	.temp_alert_config		= 0x08000a05,
+	.emif_ddr_phy_ctlr_1_init	= 0x0E28420d,
+	.emif_ddr_phy_ctlr_1		= 0x0E28420d,
+	.emif_ddr_ext_phy_ctrl_1	= 0x04020080,
+	.emif_ddr_ext_phy_ctrl_2	= 0x0A414829,
+	.emif_ddr_ext_phy_ctrl_3	= 0x14829052,
+	.emif_ddr_ext_phy_ctrl_4	= 0x000520A4,
+	.emif_ddr_ext_phy_ctrl_5	= 0x04010040
+};
+
+const struct emif_regs emif_regs_ddr3_532_mhz_1cs = {
+	.sdram_config_init		= 0x61851B32,
+	.sdram_config			= 0x61851B32,
+	.sdram_config2			= 0x0,
+	.ref_ctrl			= 0x00001035,
+	.sdram_tim1			= 0xCCCF36B3,
+	.sdram_tim2			= 0x308F7FDA,
+	.sdram_tim3			= 0x027F88A8,
+	.read_idle_ctrl			= 0x00050000,
+	.zq_config			= 0x0007190B,
+	.temp_alert_config		= 0x00000000,
+	.emif_ddr_phy_ctlr_1_init	= 0x0020420A,
+	.emif_ddr_phy_ctlr_1		= 0x0024420A,
+	.emif_ddr_ext_phy_ctrl_1	= 0x04040100,
+	.emif_ddr_ext_phy_ctrl_2	= 0x00000000,
+	.emif_ddr_ext_phy_ctrl_3	= 0x00000000,
+	.emif_ddr_ext_phy_ctrl_4	= 0x00000000,
+	.emif_ddr_ext_phy_ctrl_5	= 0x04010040,
+	.emif_rd_wr_lvl_rmp_win		= 0x00000000,
+	.emif_rd_wr_lvl_rmp_ctl		= 0x80000000,
+	.emif_rd_wr_lvl_ctl		= 0x00000000,
+	.emif_rd_wr_exec_thresh		= 0x00000305
+};
+
+const struct emif_regs emif_regs_ddr3_532_mhz_1cs_es2 = {
+	.sdram_config_init              = 0x61851B32,
+	.sdram_config                   = 0x61851B32,
+	.sdram_config2			= 0x0,
+	.ref_ctrl                       = 0x00001035,
+	.sdram_tim1                     = 0xCCCF36B3,
+	.sdram_tim2                     = 0x308F7FDA,
+	.sdram_tim3                     = 0x027F88A8,
+	.read_idle_ctrl                 = 0x00050000,
+	.zq_config                      = 0x1007190B,
+	.temp_alert_config              = 0x00000000,
+	.emif_ddr_phy_ctlr_1_init       = 0x0030400A,
+	.emif_ddr_phy_ctlr_1            = 0x0034400A,
+	.emif_ddr_ext_phy_ctrl_1        = 0x04040100,
+	.emif_ddr_ext_phy_ctrl_2        = 0x00000000,
+	.emif_ddr_ext_phy_ctrl_3        = 0x00000000,
+	.emif_ddr_ext_phy_ctrl_4        = 0x00000000,
+	.emif_ddr_ext_phy_ctrl_5        = 0x4350D435,
+	.emif_rd_wr_lvl_rmp_win         = 0x00000000,
+	.emif_rd_wr_lvl_rmp_ctl         = 0x80000000,
+	.emif_rd_wr_lvl_ctl             = 0x00000000,
+	.emif_rd_wr_exec_thresh         = 0x40000305
+};
+
+const struct dmm_lisa_map_regs lisa_map_4G_x_2_x_2 = {
+	.dmm_lisa_map_0 = 0x0,
+	.dmm_lisa_map_1 = 0x0,
+	.dmm_lisa_map_2 = 0x80740300,
+	.dmm_lisa_map_3 = 0xFF020100,
+	.is_ma_present	= 0x1
+};
+
+static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs)
+{
+	switch (omap_revision()) {
+	case OMAP5430_ES1_0:
+		*regs = &emif_regs_532_mhz_2cs;
+		break;
+	case OMAP5432_ES1_0:
+		*regs = &emif_regs_ddr3_532_mhz_1cs;
+		break;
+	case OMAP5430_ES2_0:
+		*regs = &emif_regs_532_mhz_2cs_es2;
+		break;
+	case OMAP5432_ES2_0:
+	default:
+		*regs = &emif_regs_ddr3_532_mhz_1cs_es2;
+		break;
+	}
+}
+
+void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
+	__attribute__((weak, alias("emif_get_reg_dump_sdp")));
+
+static void emif_get_dmm_regs_sdp(const struct dmm_lisa_map_regs
+						**dmm_lisa_regs)
+{
+	switch (omap_revision()) {
+	case OMAP5430_ES1_0:
+	case OMAP5430_ES2_0:
+	case OMAP5432_ES1_0:
+	case OMAP5432_ES2_0:
+	default:
+		*dmm_lisa_regs = &lisa_map_4G_x_2_x_2;
+		break;
+	}
+
+}
+
+void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
+	__attribute__((weak, alias("emif_get_dmm_regs_sdp")));
+#else
+
+static const struct lpddr2_device_details dev_4G_S4_details = {
+	.type		= LPDDR2_TYPE_S4,
+	.density	= LPDDR2_DENSITY_4Gb,
+	.io_width	= LPDDR2_IO_WIDTH_32,
+	.manufacturer	= LPDDR2_MANUFACTURER_SAMSUNG
+};
+
+static void emif_get_device_details_sdp(u32 emif_nr,
+		struct lpddr2_device_details *cs0_device_details,
+		struct lpddr2_device_details *cs1_device_details)
+{
+	/* EMIF1 & EMIF2 have identical configuration */
+	*cs0_device_details = dev_4G_S4_details;
+	*cs1_device_details = dev_4G_S4_details;
+}
+
+void emif_get_device_details(u32 emif_nr,
+		struct lpddr2_device_details *cs0_device_details,
+		struct lpddr2_device_details *cs1_device_details)
+	__attribute__((weak, alias("emif_get_device_details_sdp")));
+
+#endif /* CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS */
+
+const u32 ext_phy_ctrl_const_base[] = {
+	0x01004010,
+	0x00001004,
+	0x04010040,
+	0x01004010,
+	0x00001004,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x80080080,
+	0x00800800,
+	0x08102040,
+	0x00000001,
+	0x540A8150,
+	0xA81502a0,
+	0x002A0540,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x00000077,
+	0x0
+};
+
+const u32 ddr3_ext_phy_ctrl_const_base_es1[] = {
+	0x01004010,
+	0x00001004,
+	0x04010040,
+	0x01004010,
+	0x00001004,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x80080080,
+	0x00800800,
+	0x08102040,
+	0x00000002,
+	0x0,
+	0x0,
+	0x0,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x00000057,
+	0x0
+};
+
+const u32 ddr3_ext_phy_ctrl_const_base_es2[] = {
+	0x50D4350D,
+	0x00000D43,
+	0x04010040,
+	0x01004010,
+	0x00001004,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x80080080,
+	0x00800800,
+	0x08102040,
+	0x00000002,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x00000000,
+	0x00000057,
+	0x0
+};
+
+/* Ext phy ctrl 1-35 regs */
+const u32
+dra_ddr3_ext_phy_ctrl_const_base_es1_emif1[] = {
+	0x10040100,
+	0x00910091,
+	0x00950095,
+	0x009B009B,
+	0x009E009E,
+	0x00980098,
+	0x00340034,
+	0x00350035,
+	0x00340034,
+	0x00310031,
+	0x00340034,
+	0x007F007F,
+	0x007F007F,
+	0x007F007F,
+	0x007F007F,
+	0x007F007F,
+	0x00480048,
+	0x004A004A,
+	0x00520052,
+	0x00550055,
+	0x00500050,
+	0x00000000,
+	0x00600020,
+	0x40011080,
+	0x08102040,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0
+};
+
+/* Ext phy ctrl 1-35 regs */
+const u32
+dra_ddr3_ext_phy_ctrl_const_base_es1_emif2[] = {
+	0x10040100,
+	0x00910091,
+	0x00950095,
+	0x009B009B,
+	0x009E009E,
+	0x00980098,
+	0x00330033,
+	0x00330033,
+	0x002F002F,
+	0x00320032,
+	0x00310031,
+	0x007F007F,
+	0x007F007F,
+	0x007F007F,
+	0x007F007F,
+	0x007F007F,
+	0x00520052,
+	0x00520052,
+	0x00470047,
+	0x00490049,
+	0x00500050,
+	0x00000000,
+	0x00600020,
+	0x40011080,
+	0x08102040,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0
+};
+
+/* Ext phy ctrl 1-35 regs */
+const u32
+dra_ddr3_ext_phy_ctrl_const_base_666MHz[] = {
+	0x10040100,
+	0x00A400A4,
+	0x00A900A9,
+	0x00B000B0,
+	0x00B000B0,
+	0x00A400A4,
+	0x00390039,
+	0x00320032,
+	0x00320032,
+	0x00320032,
+	0x00440044,
+	0x00550055,
+	0x00550055,
+	0x00550055,
+	0x00550055,
+	0x007F007F,
+	0x004D004D,
+	0x00430043,
+	0x00560056,
+	0x00540054,
+	0x00600060,
+	0x0,
+	0x00600020,
+	0x40010080,
+	0x08102040,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0,
+	0x0
+};
+
+const u32 dra_ddr3_ext_phy_ctrl_const_base_666MHz_es2[] = {
+	0x04040100,
+	0x006B009F,
+	0x006B00A2,
+	0x006B00A8,
+	0x006B00A8,
+	0x006B00B2,
+	0x002F002F,
+	0x002F002F,
+	0x002F002F,
+	0x002F002F,
+	0x002F002F,
+	0x00600073,
+	0x00600071,
+	0x0060007C,
+	0x0060007E,
+	0x00600084,
+	0x00400053,
+	0x00400051,
+	0x0040005C,
+	0x0040005E,
+	0x00400064,
+	0x00800080,
+	0x00800080,
+	0x40010080,
+	0x08102040,
+	0x005B008F,
+	0x005B0092,
+	0x005B0098,
+	0x005B0098,
+	0x005B00A2,
+	0x00300043,
+	0x00300041,
+	0x0030004C,
+	0x0030004E,
+	0x00300054,
+	0x00000077
+};
+
+const struct lpddr2_mr_regs mr_regs = {
+	.mr1	= MR1_BL_8_BT_SEQ_WRAP_EN_NWR_8,
+	.mr2	= 0x6,
+	.mr3	= 0x1,
+	.mr10	= MR10_ZQ_ZQINIT,
+	.mr16	= MR16_REF_FULL_ARRAY
+};
+
+void __weak emif_get_ext_phy_ctrl_const_regs(u32 emif_nr,
+					     const u32 **regs,
+					     u32 *size)
+{
+	switch (omap_revision()) {
+	case OMAP5430_ES1_0:
+	case OMAP5430_ES2_0:
+		*regs = ext_phy_ctrl_const_base;
+		*size = ARRAY_SIZE(ext_phy_ctrl_const_base);
+		break;
+	case OMAP5432_ES1_0:
+		*regs = ddr3_ext_phy_ctrl_const_base_es1;
+		*size = ARRAY_SIZE(ddr3_ext_phy_ctrl_const_base_es1);
+		break;
+	case OMAP5432_ES2_0:
+		*regs = ddr3_ext_phy_ctrl_const_base_es2;
+		*size = ARRAY_SIZE(ddr3_ext_phy_ctrl_const_base_es2);
+		break;
+	case DRA752_ES1_0:
+	case DRA752_ES1_1:
+	case DRA752_ES2_0:
+		if (emif_nr == 1) {
+			*regs = dra_ddr3_ext_phy_ctrl_const_base_es1_emif1;
+			*size =
+			ARRAY_SIZE(dra_ddr3_ext_phy_ctrl_const_base_es1_emif1);
+		} else {
+			*regs = dra_ddr3_ext_phy_ctrl_const_base_es1_emif2;
+			*size =
+			ARRAY_SIZE(dra_ddr3_ext_phy_ctrl_const_base_es1_emif2);
+		}
+		break;
+	case DRA722_ES1_0:
+		*regs = dra_ddr3_ext_phy_ctrl_const_base_666MHz;
+		*size = ARRAY_SIZE(dra_ddr3_ext_phy_ctrl_const_base_666MHz);
+		break;
+	case DRA762_ES1_0:
+	case DRA762_ABZ_ES1_0:
+	case DRA762_ACD_ES1_0:
+	case DRA722_ES2_0:
+	case DRA722_ES2_1:
+		*regs = dra_ddr3_ext_phy_ctrl_const_base_666MHz_es2;
+		*size = ARRAY_SIZE(dra_ddr3_ext_phy_ctrl_const_base_666MHz_es2);
+		break;
+	default:
+		*regs = ddr3_ext_phy_ctrl_const_base_es2;
+		*size = ARRAY_SIZE(ddr3_ext_phy_ctrl_const_base_es2);
+
+	}
+}
+
+void get_lpddr2_mr_regs(const struct lpddr2_mr_regs **regs)
+{
+	*regs = &mr_regs;
+}
+
+static void do_ext_phy_settings_omap5(u32 base, const struct emif_regs *regs)
+{
+	u32 *ext_phy_ctrl_base = 0;
+	u32 *emif_ext_phy_ctrl_base = 0;
+	u32 emif_nr;
+	const u32 *ext_phy_ctrl_const_regs;
+	u32 i = 0;
+	u32 size;
+
+	emif_nr = (base == EMIF1_BASE) ? 1 : 2;
+
+	struct emif_reg_struct *emif = (struct emif_reg_struct *)base;
+
+	ext_phy_ctrl_base = (u32 *) &(regs->emif_ddr_ext_phy_ctrl_1);
+	emif_ext_phy_ctrl_base = (u32 *) &(emif->emif_ddr_ext_phy_ctrl_1);
+
+	/* Configure external phy control timing registers */
+	for (i = 0; i < EMIF_EXT_PHY_CTRL_TIMING_REG; i++) {
+		writel(*ext_phy_ctrl_base, emif_ext_phy_ctrl_base++);
+		/* Update shadow registers */
+		writel(*ext_phy_ctrl_base++, emif_ext_phy_ctrl_base++);
+	}
+
+	/*
+	 * external phy 6-24 registers do not change with
+	 * ddr frequency
+	 */
+	emif_get_ext_phy_ctrl_const_regs(emif_nr,
+					 &ext_phy_ctrl_const_regs, &size);
+
+	for (i = 0; i < size; i++) {
+		writel(ext_phy_ctrl_const_regs[i],
+		       emif_ext_phy_ctrl_base++);
+		/* Update shadow registers */
+		writel(ext_phy_ctrl_const_regs[i],
+		       emif_ext_phy_ctrl_base++);
+	}
+}
+
+static void do_ext_phy_settings_dra7(u32 base, const struct emif_regs *regs)
+{
+	struct emif_reg_struct *emif = (struct emif_reg_struct *)base;
+	u32 *emif_ext_phy_ctrl_base = 0;
+	u32 emif_nr;
+	const u32 *ext_phy_ctrl_const_regs;
+	u32 i, hw_leveling, size, phy;
+
+	emif_nr = (base == EMIF1_BASE) ? 1 : 2;
+
+	hw_leveling = regs->emif_rd_wr_lvl_rmp_ctl >> EMIF_REG_RDWRLVL_EN_SHIFT;
+	phy = regs->emif_ddr_phy_ctlr_1_init;
+
+	emif_ext_phy_ctrl_base = (u32 *)&(emif->emif_ddr_ext_phy_ctrl_1);
+
+	emif_get_ext_phy_ctrl_const_regs(emif_nr,
+					 &ext_phy_ctrl_const_regs, &size);
+
+	writel(ext_phy_ctrl_const_regs[0], &emif_ext_phy_ctrl_base[0]);
+	writel(ext_phy_ctrl_const_regs[0], &emif_ext_phy_ctrl_base[1]);
+
+	/*
+	 * Copy the predefined PHY register values
+	 * if leveling is disabled.
+	 */
+	if (phy & EMIF_DDR_PHY_CTRL_1_RDLVLGATE_MASK_MASK)
+		for (i = 1; i < 6; i++) {
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2]);
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2 + 1]);
+		}
+
+	if (phy & EMIF_DDR_PHY_CTRL_1_RDLVL_MASK_MASK)
+		for (i = 6; i < 11; i++) {
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2]);
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2 + 1]);
+		}
+
+	if (phy & EMIF_DDR_PHY_CTRL_1_WRLVL_MASK_MASK)
+		for (i = 11; i < 25; i++) {
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2]);
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2 + 1]);
+		}
+
+	if (hw_leveling) {
+		/*
+		 * Write the init value for HW levling to occur
+		 */
+		for (i = 21; i < 35; i++) {
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2]);
+			writel(ext_phy_ctrl_const_regs[i],
+			       &emif_ext_phy_ctrl_base[i * 2 + 1]);
+		}
+	}
+}
+
+void do_ext_phy_settings(u32 base, const struct emif_regs *regs)
+{
+	if (is_omap54xx())
+		do_ext_phy_settings_omap5(base, regs);
+	else
+		do_ext_phy_settings_dra7(base, regs);
+}
+
+#ifndef CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
+static const struct lpddr2_ac_timings timings_jedec_532_mhz = {
+	.max_freq	= 532000000,
+	.RL		= 8,
+	.tRPab		= 21,
+	.tRCD		= 18,
+	.tWR		= 15,
+	.tRASmin	= 42,
+	.tRRD		= 10,
+	.tWTRx2		= 15,
+	.tXSR		= 140,
+	.tXPx2		= 15,
+	.tRFCab		= 130,
+	.tRTPx2		= 15,
+	.tCKE		= 3,
+	.tCKESR		= 15,
+	.tZQCS		= 90,
+	.tZQCL		= 360,
+	.tZQINIT	= 1000,
+	.tDQSCKMAXx2	= 11,
+	.tRASmax	= 70,
+	.tFAW		= 50
+};
+
+static const struct lpddr2_min_tck min_tck = {
+	.tRL		= 3,
+	.tRP_AB		= 3,
+	.tRCD		= 3,
+	.tWR		= 3,
+	.tRAS_MIN	= 3,
+	.tRRD		= 2,
+	.tWTR		= 2,
+	.tXP		= 2,
+	.tRTP		= 2,
+	.tCKE		= 3,
+	.tCKESR		= 3,
+	.tFAW		= 8
+};
+
+static const struct lpddr2_ac_timings *ac_timings[MAX_NUM_SPEEDBINS] = {
+	&timings_jedec_532_mhz
+};
+
+static const struct lpddr2_device_timings dev_4G_S4_timings = {
+	.ac_timings	= ac_timings,
+	.min_tck	= &min_tck,
+};
+
+/*
+ * List of status registers to be controlled back to control registers
+ * after initial leveling
+ * readreg, writereg
+ */
+const struct read_write_regs omap5_bug_00339_regs[] = {
+	{ 8,  5 },
+	{ 9,  6 },
+	{ 10, 7 },
+	{ 14, 8 },
+	{ 15, 9 },
+	{ 16, 10 },
+	{ 11, 2 },
+	{ 12, 3 },
+	{ 13, 4 },
+	{ 17, 11 },
+	{ 18, 12 },
+	{ 19, 13 },
+};
+
+const struct read_write_regs dra_bug_00339_regs[] = {
+	{ 7,  7 },
+	{ 8,  8 },
+	{ 9,  9 },
+	{ 10, 10 },
+	{ 11, 11 },
+	{ 12, 2 },
+	{ 13, 3 },
+	{ 14, 4 },
+	{ 15, 5 },
+	{ 16, 6 },
+	{ 17, 12 },
+	{ 18, 13 },
+	{ 19, 14 },
+	{ 20, 15 },
+	{ 21, 16 },
+	{ 22, 17 },
+	{ 23, 18 },
+	{ 24, 19 },
+	{ 25, 20 },
+	{ 26, 21}
+};
+
+const struct read_write_regs *get_bug_regs(u32 *iterations)
+{
+	const struct read_write_regs *bug_00339_regs_ptr = NULL;
+
+	switch (omap_revision()) {
+	case OMAP5430_ES1_0:
+	case OMAP5430_ES2_0:
+	case OMAP5432_ES1_0:
+	case OMAP5432_ES2_0:
+		bug_00339_regs_ptr = omap5_bug_00339_regs;
+		*iterations = sizeof(omap5_bug_00339_regs)/
+			     sizeof(omap5_bug_00339_regs[0]);
+		break;
+	case DRA762_ABZ_ES1_0:
+	case DRA762_ACD_ES1_0:
+	case DRA762_ES1_0:
+	case DRA752_ES1_0:
+	case DRA752_ES1_1:
+	case DRA752_ES2_0:
+	case DRA722_ES1_0:
+	case DRA722_ES2_0:
+	case DRA722_ES2_1:
+		bug_00339_regs_ptr = dra_bug_00339_regs;
+		*iterations = sizeof(dra_bug_00339_regs)/
+			     sizeof(dra_bug_00339_regs[0]);
+		break;
+	default:
+		printf("\n Error: UnKnown SOC");
+	}
+
+	return bug_00339_regs_ptr;
+}
+
+void emif_get_device_timings_sdp(u32 emif_nr,
+		const struct lpddr2_device_timings **cs0_device_timings,
+		const struct lpddr2_device_timings **cs1_device_timings)
+{
+	/* Identical devices on EMIF1 & EMIF2 */
+	*cs0_device_timings = &dev_4G_S4_timings;
+	*cs1_device_timings = &dev_4G_S4_timings;
+}
+
+void emif_get_device_timings(u32 emif_nr,
+		const struct lpddr2_device_timings **cs0_device_timings,
+		const struct lpddr2_device_timings **cs1_device_timings)
+	__attribute__((weak, alias("emif_get_device_timings_sdp")));
+
+#endif /* CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS */
diff --git a/roms/u-boot/arch/arm/mach-omap2/omap5/sec_entry_cpu1.S b/roms/u-boot/arch/arm/mach-omap2/omap5/sec_entry_cpu1.S
new file mode 100644
index 000000000..32de9d3d4
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-omap2/omap5/sec_entry_cpu1.S
@@ -0,0 +1,122 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Secure entry function for CPU Core #1
+ *
+ * (C) Copyright 2016
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author :
+ *	Harinarayan Bhatta <harinarayan@ti.com>
+ */
+
+#include <config.h>
+#include <asm/arch/omap.h>
+#include <asm/omap_common.h>
+#include <linux/linkage.h>
+
+.arch_extension sec
+
+#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
+.global flush_dcache_range
+#endif
+
+#define AUX_CORE_BOOT_0		0x48281800
+#define AUX_CORE_BOOT_1		0x48281804
+
+#ifdef CONFIG_DRA7XX
+/* DRA7xx ROM code function "startup_BootSlave". This function is where CPU1
+ * waits on WFE, polling on AUX_CORE_BOOT_x registers.
+ * This address is same for J6 and J6 Eco.
+ */
+#define ROM_FXN_STARTUP_BOOTSLAVE     0x00038a64
+#endif
+
+/* Assembly core where CPU1 is woken up into
+ * No need to save-restore registers, does not use stack.
+ */
+LENTRY(cpu1_entry)
+	ldr	r4, =omap_smc_sec_cpu1_args
+	ldm	r4, {r0,r1,r2,r3}	@ Retrieve args
+
+	mov	r6, #0xFF	@ Indicate new Task call
+	mov	r12, #0x00	@ Secure Service ID in R12
+
+	dsb
+	dmb
+	smc	0		@ SMC #0 to enter monitor mode
+
+	b	.Lend		@ exit at end of the service execution
+	nop
+
+	@ In case of IRQ happening in Secure, then ARM will branch here.
+	@ At that moment, IRQ will be pending and ARM will jump to Non Secure
+	@ IRQ handler
+	mov	r12, #0xFE
+
+	dsb
+	dmb
+	smc	0		@ SMC #0 to enter monitor mode
+
+.Lend:
+	ldr	r4, =omap_smc_sec_cpu1_args
+	str	r0, [r4, #0x10]		@ save return value
+	ldr	r4, =AUX_CORE_BOOT_0
+	mov	r5, #0x0
+	str	r5, [r4]
+	ldr	r4, =ROM_FXN_STARTUP_BOOTSLAVE
+	sev				@ Tell CPU0 we are done
+	bx	r4			@ Jump back to ROM
+END(cpu1_entry)
+
+/*
+ * u32 omap_smc_sec_cpu1(u32 service, u32 proc_id, u32 flag, u32 *params);
+ *
+ * Makes a secure ROM/PPA call on CPU Core #1 on supported platforms.
+ * Assumes that CPU #1 is waiting in ROM code and not yet woken up or used by
+ * u-boot.
+ */
+ENTRY(omap_smc_sec_cpu1)
+	push	{r4, r5, lr}
+	ldr	r4, =omap_smc_sec_cpu1_args
+	stm	r4, {r0,r1,r2,r3}	@ Save args to memory
+#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
+	mov	r0, r4
+	mov	r1, #CONFIG_SYS_CACHELINE_SIZE
+	add	r1, r0, r1		@ dcache is not enabled on CPU1, so
+	blx	flush_dcache_range	@ flush the cache on args buffer
+#endif
+	ldr	r4, =AUX_CORE_BOOT_1
+	ldr	r5, =cpu1_entry
+	str	r5, [r4]		@ Setup CPU1 entry function
+	ldr	r4, =AUX_CORE_BOOT_0
+	mov	r5, #0x10
+	str	r5, [r4]		@ Tell ROM to exit while loop
+	sev				@ Wake up CPU1
+.Lwait:
+	wfe				@ Wait for CPU1 to finish
+	nop
+	ldr	r5, [r4]		@ Check if CPU1 is done
+	cmp	r5, #0
+	bne	.Lwait
+
+	ldr	r4, =omap_smc_sec_cpu1_args
+	ldr	r0, [r4, #0x10]         @ Retrieve return value
+	pop	{r4, r5, pc}
+ENDPROC(omap_smc_sec_cpu1)
+
+/*
+ * Buffer to save function arguments and return value for omap_smc_sec_cpu1
+ */
+.section .data
+omap_smc_sec_cpu1_args:
+#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
+	.balign CONFIG_SYS_CACHELINE_SIZE
+	.rept  CONFIG_SYS_CACHELINE_SIZE/4
+	.word 0
+	.endr
+#else
+	.rept 5
+	.word 0
+	.endr
+#endif
+END(omap_smc_sec_cpu1_args)