Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

1 files changed, 102 insertions, 0 deletions

diff --git a/roms/u-boot/arch/x86/cpu/apollolake/cpu_common.c b/roms/u-boot/arch/x86/cpu/apollolake/cpu_common.c
new file mode 100644
index 000000000..5d7d26b14
--- /dev/null
+++ b/roms/u-boot/arch/x86/cpu/apollolake/cpu_common.c
@@ -0,0 +1,102 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2019 Google LLC
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <log.h>
+#include <asm/cpu_common.h>
+#include <asm/io.h>
+#include <asm/msr.h>
+#include <asm/pci.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/iomap.h>
+#include <asm/arch/uart.h>
+#include <power/acpi_pmc.h>
+
+/* Define this here to avoid referencing any drivers for the debug UART 1 */
+#define PCH_DEV_P2SB	PCI_BDF(0, 0x0d, 0)
+
+void cpu_flush_l1d_to_l2(void)
+{
+	struct msr_t msr;
+
+	msr = msr_read(MSR_POWER_MISC);
+	msr.lo |= FLUSH_DL1_L2;
+	msr_write(MSR_POWER_MISC, msr);
+}
+
+void enable_pm_timer_emulation(const struct udevice *pmc)
+{
+	struct acpi_pmc_upriv *upriv = dev_get_uclass_priv(pmc);
+	msr_t msr;
+
+	/*
+	 * The derived frequency is calculated as follows:
+	 *    (CTC_FREQ * msr[63:32]) >> 32 = target frequency.
+	 *
+	 * Back-solve the multiplier so the 3.579545MHz ACPI timer frequency is
+	 * used.
+	 */
+	msr.hi = (3579545ULL << 32) / CTC_FREQ;
+
+	/* Set PM1 timer IO port and enable */
+	msr.lo = EMULATE_PM_TMR_EN | (upriv->acpi_base + R_ACPI_PM1_TMR);
+	debug("PM timer %x %x\n", msr.hi, msr.lo);
+	msr_write(MSR_EMULATE_PM_TIMER, msr);
+}
+
+static void pch_uart_init(void)
+{
+	/*
+	 * Set up the pinmux so that the UART rx/tx signals are connected
+	 * outside the SoC.
+	 *
+	 * There are about 500 lines of code required to program the GPIO
+	 * configuration for the UARTs. But it boils down to four writes, and
+	 * for the debug UART we want the minimum possible amount of code before
+	 * the UART is running. So just add the magic writes here. See
+	 * apl_hostbridge_early_init_pinctrl() for the full horror.
+	 */
+	if (PCI_FUNC(PCH_DEV_UART) == 1) {
+		writel(0x40000402, 0xd0c50650);
+		writel(0x3c47, 0xd0c50654);
+		writel(0x40000400, 0xd0c50658);
+		writel(0x3c48, 0xd0c5065c);
+	} else { /* UART2 */
+		writel(0x40000402, 0xd0c50670);
+		writel(0x3c4b, 0xd0c50674);
+		writel(0x40000400, 0xd0c50678);
+		writel(0x3c4c, 0xd0c5067c);
+	}
+
+#ifdef CONFIG_DEBUG_UART
+	apl_uart_init(PCH_DEV_UART, CONFIG_DEBUG_UART_BASE);
+#endif
+}
+
+static void p2sb_enable_bar(ulong bar)
+{
+	/* Enable PCR Base address in PCH */
+	pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_0, bar,
+			     PCI_SIZE_32);
+	pci_x86_write_config(PCH_DEV_P2SB, PCI_BASE_ADDRESS_1, 0, PCI_SIZE_32);
+
+	/* Enable P2SB MSE */
+	pci_x86_write_config(PCH_DEV_P2SB, PCI_COMMAND,
+			     PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY,
+			     PCI_SIZE_8);
+}
+
+/*
+ * board_debug_uart_init() - Init the debug UART ready for use
+ *
+ * This is the minimum init needed to get the UART running. It avoids any
+ * drivers or complex code, so that the UART is running as soon as possible.
+ */
+void board_debug_uart_init(void)
+{
+	p2sb_enable_bar(IOMAP_P2SB_BAR);
+	pch_uart_init();
+}