Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

1 files changed, 207 insertions, 0 deletions

diff --git a/roms/u-boot/board/liebherr/xea/xea.c b/roms/u-boot/board/liebherr/xea/xea.c
new file mode 100644
index 000000000..cd11b0ada
--- /dev/null
+++ b/roms/u-boot/board/liebherr/xea/xea.c
@@ -0,0 +1,207 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * XEA iMX28 board
+ *
+ * Copyright (C) 2019 DENX Software Engineering
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ *
+ * Copyright (C) 2018 DENX Software Engineering
+ * Måns Rullgård, DENX Software Engineering, mans@mansr.com
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ */
+
+#include <common.h>
+#include <fdt_support.h>
+#include <init.h>
+#include <log.h>
+#include <net.h>
+#include <asm/global_data.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/delay.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+#include <usb.h>
+#include <serial.h>
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+
+static void init_clocks(void)
+{
+	/* IO0 clock at 480MHz */
+	mxs_set_ioclk(MXC_IOCLK0, 480000);
+	/* IO1 clock at 480MHz */
+	mxs_set_ioclk(MXC_IOCLK1, 480000);
+
+	/* SSP0 clock at 96MHz */
+	mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
+	/* SSP2 clock at 160MHz */
+	mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
+	/* SSP3 clock at 96MHz */
+	mxs_set_sspclk(MXC_SSPCLK3, 96000, 0);
+}
+
+#ifdef CONFIG_SPL_BUILD
+void board_init_f(ulong arg)
+{
+	init_clocks();
+	preloader_console_init();
+}
+
+static int boot_tiva0, boot_tiva1;
+
+/* Check if TIVAs request booting via U-Boot proper */
+void spl_board_init(void)
+{
+	struct gpio_desc btiva0, btiva1, en_3_3v;
+	int ret;
+
+	/*
+	 * Setup GPIO0_0 (TIVA power enable pin) to be output high
+	 * to allow TIVA startup.
+	 */
+	ret = dm_gpio_lookup_name("GPIO0_0", &en_3_3v);
+	if (ret)
+		printf("Cannot get GPIO0_0\n");
+
+	ret = dm_gpio_request(&en_3_3v, "pwr_3_3v");
+	if (ret)
+		printf("Cannot request GPIO0_0\n");
+
+	/* Set GPIO0_0 to HIGH */
+	dm_gpio_set_dir_flags(&en_3_3v, GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+
+	ret = dm_gpio_lookup_name("GPIO0_23", &btiva0);
+	if (ret)
+		printf("Cannot get GPIO0_23\n");
+
+	ret = dm_gpio_lookup_name("GPIO0_25", &btiva1);
+	if (ret)
+		printf("Cannot get GPIO0_25\n");
+
+	ret = dm_gpio_request(&btiva0, "boot-tiva0");
+	if (ret)
+		printf("Cannot request GPIO0_23\n");
+
+	ret = dm_gpio_request(&btiva1, "boot-tiva1");
+	if (ret)
+		printf("Cannot request GPIO0_25\n");
+
+	dm_gpio_set_dir_flags(&btiva0, GPIOD_IS_IN);
+	dm_gpio_set_dir_flags(&btiva1, GPIOD_IS_IN);
+
+	udelay(1000);
+
+	boot_tiva0 = dm_gpio_get_value(&btiva0);
+	boot_tiva1 = dm_gpio_get_value(&btiva1);
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+	spl_boot_list[0] = BOOT_DEVICE_MMC1;
+	spl_boot_list[1] = BOOT_DEVICE_SPI;
+	spl_boot_list[2] = BOOT_DEVICE_UART;
+}
+
+int spl_start_uboot(void)
+{
+	/* break into full u-boot on 'c' */
+	if (serial_tstc() && serial_getc() == 'c')
+		return 1;
+
+	debug("%s: btiva0: %d btiva1: %d\n", __func__, boot_tiva0, boot_tiva1);
+	return !boot_tiva0 || !boot_tiva1;
+}
+#else
+
+int board_early_init_f(void)
+{
+	init_clocks();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	struct gpio_desc phy_rst;
+	int ret;
+
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+	cpu_eth_init(NULL);
+
+	/* PHY INT#/PWDN# */
+	ret = dm_gpio_lookup_name("GPIO4_13", &phy_rst);
+	if (ret) {
+		printf("Cannot get GPIO4_13\n");
+		return ret;
+	}
+
+	ret = dm_gpio_request(&phy_rst, "phy-rst");
+	if (ret) {
+		printf("Cannot request GPIO4_13\n");
+		return ret;
+	}
+
+	dm_gpio_set_dir_flags(&phy_rst, GPIOD_IS_IN);
+	udelay(1000);
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	return mxs_dram_init();
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+static int fdt_fixup_l2switch(void *blob)
+{
+	u8 ethaddr[6];
+	int ret;
+
+	if (eth_env_get_enetaddr("ethaddr", ethaddr)) {
+		ret = fdt_find_and_setprop(blob,
+					   "/ahb@80080000/switch@800f0000",
+					   "local-mac-address", ethaddr, 6, 1);
+		if (ret < 0)
+			printf("%s: can't find usbether@1 node: %d\n",
+			       __func__, ret);
+	}
+
+	return 0;
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+	/*
+	 * i.MX28 L2 switch needs manual update (fixup) of eth MAC address
+	 * (in 'local-mac-address' property) as it uses "switch@800f0000"
+	 * node, not set by default FIT image handling code in
+	 * "ethernet@800f0000"
+	 */
+	fdt_fixup_l2switch(blob);
+
+	return 0;
+}
+#endif
+
+#endif	/* CONFIG_SPL_BUILD */