Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

2 files changed, 103 insertions, 0 deletions

diff --git a/roms/u-boot/doc/device-tree-bindings/thermal/rockchip-thermal.txt b/roms/u-boot/doc/device-tree-bindings/thermal/rockchip-thermal.txt
new file mode 100644
index 000000000..ef802de49
--- /dev/null
+++ b/roms/u-boot/doc/device-tree-bindings/thermal/rockchip-thermal.txt
@@ -0,0 +1,68 @@
+* Temperature Sensor ADC (TSADC) on rockchip SoCs
+
+Required properties:
+- compatible : "rockchip,rk3288-tsadc"
+- reg : physical base address of the controller and length of memory mapped
+	region.
+- interrupts : The interrupt number to the cpu. The interrupt specifier format
+	       depends on the interrupt controller.
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for
+		the peripheral clock.
+- resets : Must contain an entry for each entry in reset-names.
+	   See ../reset/reset.txt for details.
+- reset-names : Must include the name "tsadc-apb".
+- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description.
+- rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value.
+- rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO.
+- rockchip,hw-tshut-polarity : The hardware-controlled active polarity 0:LOW
+			       1:HIGH.
+
+Exiample:
+tsadc: tsadc@ff280000 {
+	compatible = "rockchip,rk3288-tsadc";
+	reg = <0xff280000 0x100>;
+	interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
+	clock-names = "tsadc", "apb_pclk";
+	resets = <&cru SRST_TSADC>;
+	reset-names = "tsadc-apb";
+	pinctrl-names = "default";
+	pinctrl-0 = <&otp_out>;
+	#thermal-sensor-cells = <1>;
+	rockchip,hw-tshut-temp = <95000>;
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+};
+
+Example: referring to thermal sensors:
+thermal-zones {
+	cpu_thermal: cpu_thermal {
+		polling-delay-passive = <1000>; /* milliseconds */
+		polling-delay = <5000>; /* milliseconds */
+
+		/* sensor	ID */
+		thermal-sensors = <&tsadc	1>;
+
+		trips {
+			cpu_alert0: cpu_alert {
+				temperature = <70000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "passive";
+			};
+			cpu_crit: cpu_crit {
+				temperature = <90000>; /* millicelsius */
+				hysteresis = <2000>; /* millicelsius */
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&cpu_alert0>;
+				cooling-device =
+				    <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
diff --git a/roms/u-boot/doc/device-tree-bindings/thermal/ti_soc_thermal.txt b/roms/u-boot/doc/device-tree-bindings/thermal/ti_soc_thermal.txt
new file mode 100644
index 000000000..b4e88c2d1
--- /dev/null
+++ b/roms/u-boot/doc/device-tree-bindings/thermal/ti_soc_thermal.txt
@@ -0,0 +1,35 @@
+* Texas Instrument dra7xx SCM bandgap bindings
+
+In the System Control Module, SoC supplies a voltage reference
+and a temperature sensor feature that are gathered in the band
+gap voltage and temperature sensor (VBGAPTS) module. The band
+gap provides current and voltage reference for its internal
+circuits and other analog IP blocks. The analog-to-digital
+converter (ADC) produces an output value that is proportional
+to the silicon temperature.
+
+Required properties:
+- compatible : Should be:
+  - "ti,dra752-bandgap"
+- interrupts : this entry should indicate which interrupt line
+the talert signal is routed to;
+- regs : this is specific to each bandgap version, because
+the mapping may change from soc to soc, apart from depending
+on available features.
+
+Optional:
+- gpios : this entry should be used to inform which GPIO
+line the tshut signal is routed to. The informed GPIO will
+be treated as an IRQ;
+
+Example:
+bandgap {
+	reg = <0x4a0021e0 0xc
+		0x4a00232c 0xc
+		0x4a002380 0x2c
+		0x4a0023C0 0x3c
+		0x4a002564 0x8
+		0x4a002574 0x50>;
+	compatible = "ti,dra752-bandgap";
+	interrupts = <0 126 4>; /* talert */
+};