Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

1 files changed, 182 insertions, 0 deletions

diff --git a/roms/u-boot/include/configs/M5272C3.h b/roms/u-boot/include/configs/M5272C3.h
new file mode 100644
index 000000000..2cdd4369d
--- /dev/null
+++ b/roms/u-boot/include/configs/M5272C3.h
@@ -0,0 +1,182 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuation settings for the Motorola MC5272C3 board.
+ *
+ * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5272C3_H
+#define _M5272C3_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CONFIG_SYS_UART_PORT		(0)
+
+#undef CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT 10000	/* timeout in milliseconds */
+
+#undef CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+
+#define LDS_BOARD_TEXT \
+	. = DEFINED(env_offset) ? env_offset : .; \
+	env/embedded.o(.text);
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_MII_INIT		1
+#	define CONFIG_SYS_DISCOVER_PHY
+#	define CONFIG_SYS_RX_ETH_BUFFER	8
+#	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CONFIG_SYS_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CONFIG_SYS_DISCOVER_PHY */
+#endif
+
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#endif				/* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME		"M5272C3"
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
+
+#define CONFIG_SYS_LOAD_ADDR		0x20000
+#define CONFIG_SYS_CLK			66000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+#define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */
+#define CONFIG_SYS_SCR			0x0003
+#define CONFIG_SYS_SPR			0xffff
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM    */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_SDRAM_SIZE		4	/* SDRAM size in MB */
+#define CONFIG_SYS_FLASH_BASE		0xffe00000
+
+#ifdef	CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_SYS_MONITOR_BASE	0x20000
+#else
+#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
+#endif
+
+#define CONFIG_SYS_MONITOR_LEN		0x20000
+#define CONFIG_SYS_MALLOC_LEN		(256 << 10)
+#define CONFIG_SYS_BOOTPARAMS_LEN	64*1024
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
+
+/*
+ * FLASH organization
+ */
+#ifdef CONFIG_SYS_FLASH_CFI
+#	define CONFIG_SYS_FLASH_SIZE		0x800000	/* Max size that the board might have */
+#	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CONFIG_SYS_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CONFIG_SYS_CACHELINE_SIZE	16
+
+#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - 4)
+#define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINV | CF_CACR_INVI)
+#define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_SDRAM_BASE | \
+					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+					 CF_ACR_EN | CF_ACR_SM_ALL)
+#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CINV | \
+					 CF_CACR_DISD | CF_CACR_INVI | \
+					 CF_CACR_CEIB | CF_CACR_DCM | \
+					 CF_CACR_EUSP)
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+#define CONFIG_SYS_BR0_PRELIM		0xFFE00201
+#define CONFIG_SYS_OR0_PRELIM		0xFFE00014
+#define CONFIG_SYS_BR1_PRELIM		0
+#define CONFIG_SYS_OR1_PRELIM		0
+#define CONFIG_SYS_BR2_PRELIM		0x30000001
+#define CONFIG_SYS_OR2_PRELIM		0xFFF80000
+#define CONFIG_SYS_BR3_PRELIM		0
+#define CONFIG_SYS_OR3_PRELIM		0
+#define CONFIG_SYS_BR4_PRELIM		0
+#define CONFIG_SYS_OR4_PRELIM		0
+#define CONFIG_SYS_BR5_PRELIM		0
+#define CONFIG_SYS_OR5_PRELIM		0
+#define CONFIG_SYS_BR6_PRELIM		0
+#define CONFIG_SYS_OR6_PRELIM		0
+#define CONFIG_SYS_BR7_PRELIM		0x00000701
+#define CONFIG_SYS_OR7_PRELIM		0xFFC0007C
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define CONFIG_SYS_PACNT		0x00000000
+#define CONFIG_SYS_PADDR		0x0000
+#define CONFIG_SYS_PADAT		0x0000
+#define CONFIG_SYS_PBCNT		0x55554155	/* Ethernet/UART configuration */
+#define CONFIG_SYS_PBDDR		0x0000
+#define CONFIG_SYS_PBDAT		0x0000
+#define CONFIG_SYS_PDCNT		0x00000000
+#endif				/* _M5272C3_H */