Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

1 files changed, 288 insertions, 0 deletions

diff --git a/roms/u-boot/include/configs/astro_mcf5373l.h b/roms/u-boot/include/configs/astro_mcf5373l.h
new file mode 100644
index 000000000..891240c7e
--- /dev/null
+++ b/roms/u-boot/include/configs/astro_mcf5373l.h
@@ -0,0 +1,288 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration settings for the Sentec Cobra Board.
+ *
+ * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
+ */
+
+/*
+ * configuration for ASTRO "Urmel" board.
+ * Originating from Cobra5272 configuration, messed up by
+ * Wolfgang Wegner <w.wegner@astro-kom.de>
+ * Please do not bother the original author with bug reports
+ * concerning this file.
+ */
+
+#ifndef _CONFIG_ASTRO_MCF5373L_H
+#define _CONFIG_ASTRO_MCF5373L_H
+
+#include <linux/stringify.h>
+
+/*
+ * set the card type to actually compile for; either of
+ * the possibilities listed below has to be used!
+ */
+#define CONFIG_ASTRO_V532	1
+
+#if CONFIG_ASTRO_V532
+#define ASTRO_ID	0xF8
+#elif CONFIG_ASTRO_V512
+#define ASTRO_ID	0xFA
+#elif CONFIG_ASTRO_TWIN7S2
+#define ASTRO_ID	0xF9
+#elif CONFIG_ASTRO_V912
+#define ASTRO_ID	0xFC
+#elif CONFIG_ASTRO_COFDMDUOS2
+#define ASTRO_ID	0xFB
+#else
+#error No card type defined!
+#endif
+
+/*
+ * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
+ * a different bootloader that has already performed RAM setup) or
+ * started directly from flash, which is the regular case for production
+ * boards.
+ */
+#ifdef CONFIG_RAM
+#define CONFIG_MONITOR_IS_IN_RAM
+#define ENABLE_JFFS	0
+#else
+#define ENABLE_JFFS	1
+#endif
+
+#define CONFIG_MCFRTC
+#undef RTC_DEBUG
+
+/* Timer */
+#define CONFIG_MCFTMR
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	80000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x58000
+#define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR
+
+/*
+ * Defines processor clock - important for correct timings concerning serial
+ * interface etc.
+ */
+
+#define CONFIG_SYS_CLK			80000000
+#define CONFIG_SYS_CPU_CLK		(CONFIG_SYS_CLK * 3)
+#define CONFIG_SYS_SDRAM_SIZE		32		/* SDRAM size in MB */
+
+#define CONFIG_SYS_CORE_SRAM_SIZE	0x8000
+#define CONFIG_SYS_CORE_SRAM		0x80000000
+
+#define CONFIG_SYS_UNIFY_CACHE
+
+/*
+ * Define baudrate for UART1 (console output, tftp, ...)
+ * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
+ * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected
+ * in u-boot command interface
+ */
+
+#define CONFIG_MCFUART
+#define CONFIG_SYS_UART_PORT		(2)
+#define CONFIG_SYS_UART2_ALT3_GPIO
+
+/*
+ * Watchdog configuration; Watchdog is disabled for running from RAM
+ * and set to highest possible value else. Beware there is no check
+ * in the watchdog code to validate the timeout value set here!
+ */
+
+#ifndef CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT 3355	/* timeout in milliseconds */
+#endif
+
+/*
+ * Configuration for environment
+ * Environment is located in the last sector of the flash
+ */
+
+#ifndef CONFIG_MONITOR_IS_IN_RAM
+#else
+/*
+ * environment in RAM - This is used to use a single PC-based application
+ * to load an image, load U-Boot, load an environment and then start U-Boot
+ * to execute the commands from the environment. Feedback is done via setting
+ * and reading memory locations.
+ */
+#endif
+
+/* here we put our FPGA configuration... */
+
+/* Define user parameters that have to be customized most likely */
+
+/* AUTOBOOT settings - booting images automatically by u-boot after power on */
+
+/*
+ * The following settings will be contained in the environment block ; if you
+ * want to use a neutral environment all those settings can be manually set in
+ * u-boot: 'set' command
+ */
+
+#define CONFIG_EXTRA_ENV_SETTINGS			\
+	"loaderversion=11\0"				\
+	"card_id="__stringify(ASTRO_ID)"\0"			\
+	"alterafile=0\0"				\
+	"xilinxfile=0\0"				\
+	"xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\
+		"fpga load 0 0x41000000 $filesize\0" \
+	"alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\
+		"fpga load 1 0x41000000 $filesize\0" \
+	"env_default=1\0"				\
+	"env_check=if test $env_default -eq 1;"\
+		" then setenv env_default 0;saveenv;fi\0"
+
+/*
+ * "update" is a non-standard command that has to be supplied
+ * by external update.c; This is not included in mainline because
+ * it needs non-blocking CFI routines.
+ */
+#ifdef CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_BOOTCOMMAND	""	/* no autoboot in this case */
+#else
+#if CONFIG_ASTRO_V532
+#define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
+				"run xilinxload&&run alteraload&&bootm 0x80000;"\
+				"update;reset"
+#else
+#define CONFIG_BOOTCOMMAND	"protect off 0x80000 0x1ffffff;run env_check;"\
+				"run xilinxload&&bootm 0x80000;update;reset"
+#endif
+#endif
+
+/* default RAM address for user programs */
+#define CONFIG_SYS_LOAD_ADDR	0x20000
+
+#define CONFIG_FPGA_COUNT	1
+#define CONFIG_SYS_FPGA_PROG_FEEDBACK
+#define CONFIG_SYS_FPGA_WAIT		1000
+
+/* End of user parameters to be customized */
+
+/* Defines memory range for test */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/* Base register address */
+
+#define CONFIG_SYS_MBAR		0xFC000000	/* Register Base Addrs */
+
+/* System Conf. Reg. & System Protection Reg. */
+
+#define CONFIG_SYS_SCR		0x0003;
+#define CONFIG_SYS_SPR		0xffff;
+
+/*
+ * Definitions for initial stack pointer and data area (in internal SRAM)
+ */
+#define CONFIG_SYS_INIT_RAM_ADDR	0x80000000
+#define CONFIG_SYS_INIT_RAM_SIZE		0x8000
+#define CONFIG_SYS_INIT_RAM_CTRL	0x221
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000
+ */
+#define CONFIG_SYS_SDRAM_BASE		0x40000000
+
+/*
+ * Chipselect bank definitions
+ *
+ * CS0 - Flash 32MB (first 16MB)
+ * CS1 - Flash 32MB (second half)
+ * CS2 - FPGA
+ * CS3 - FPGA
+ * CS4 - unused
+ * CS5 - unused
+ */
+#define CONFIG_SYS_CS0_BASE		0
+#define CONFIG_SYS_CS0_MASK		0x00ff0001
+#define CONFIG_SYS_CS0_CTRL		0x00001fc0
+
+#define CONFIG_SYS_CS1_BASE		0x01000000
+#define CONFIG_SYS_CS1_MASK		0x00ff0001
+#define CONFIG_SYS_CS1_CTRL		0x00001fc0
+
+#define CONFIG_SYS_CS2_BASE		0x20000000
+#define CONFIG_SYS_CS2_MASK		0x00ff0001
+#define CONFIG_SYS_CS2_CTRL		0x0000fec0
+
+#define CONFIG_SYS_CS3_BASE		0x21000000
+#define CONFIG_SYS_CS3_MASK		0x00ff0001
+#define CONFIG_SYS_CS3_CTRL		0x0000fec0
+
+#define CONFIG_SYS_FLASH_BASE		0x00000000
+
+#ifdef	CONFIG_MONITOR_IS_IN_RAM
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+#else
+/* This is mainly used during relocation in start.S */
+#define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_FLASH_BASE + 0x400)
+#endif
+/* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)
+
+#define CONFIG_SYS_BOOTPARAMS_LEN	(64 * 1024)
+/* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MALLOC_LEN		(128 << 10)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + \
+						(CONFIG_SYS_SDRAM_SIZE << 20))
+
+/* FLASH organization */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	259
+#define CONFIG_SYS_FLASH_ERASE_TOUT	1000
+
+#define CONFIG_SYS_FLASH_SIZE		0x2000000
+#define CONFIG_SYS_FLASH_CFI_NONBLOCK	1
+
+#define LDS_BOARD_TEXT \
+	. = DEFINED(env_offset) ? env_offset : .; \
+	env/embedded.o(.text*)
+
+#if ENABLE_JFFS
+/* JFFS Partition offset set */
+#define CONFIG_SYS_JFFS2_FIRST_BANK    0
+#define CONFIG_SYS_JFFS2_NUM_BANKS     1
+/* 512k reserved for u-boot */
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR  0x40
+#endif
+
+/* Cache Configuration */
+#define CONFIG_SYS_CACHELINE_SIZE	16
+
+#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
+					 CONFIG_SYS_INIT_RAM_SIZE - 4)
+#define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINVA)
+#define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_SDRAM_BASE | \
+					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+					 CF_ACR_EN | CF_ACR_SM_ALL)
+#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_EC | CF_CACR_CINVA | \
+					 CF_CACR_DCM_P)
+
+#endif	/* _CONFIG_ASTRO_MCF5373L_H */