Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

1 files changed, 222 insertions, 0 deletions

diff --git a/roms/u-boot/include/configs/omapl138_lcdk.h b/roms/u-boot/include/configs/omapl138_lcdk.h
new file mode 100644
index 000000000..a37359e6c
--- /dev/null
+++ b/roms/u-boot/include/configs/omapl138_lcdk.h
@@ -0,0 +1,222 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Based on davinci_dvevm.h. Original Copyrights follow:
+ *
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * Board
+ */
+
+/*
+ * SoC Configuration
+ */
+#define CONFIG_MACH_OMAPL138_LCDK
+#define CONFIG_SYS_CLK_FREQ		clk_get(DAVINCI_ARM_CLKID)
+#define CONFIG_SYS_OSCIN_FREQ		24000000
+#define CONFIG_SYS_TIMERBASE		DAVINCI_TIMER0_BASE
+#define CONFIG_SYS_HZ_CLOCK		clk_get(DAVINCI_AUXCLK_CLKID)
+#define CONFIG_SYS_HZ			1000
+#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY
+
+/*
+ * Memory Info
+ */
+#define CONFIG_SYS_MALLOC_LEN	(0x10000 + 1*1024*1024) /* malloc() len */
+#define PHYS_SDRAM_1		DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
+#define PHYS_SDRAM_1_SIZE	(128 << 20) /* SDRAM size 128MB */
+#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
+
+#define CONFIG_SPL_BSS_START_ADDR DAVINCI_DDR_EMIF_DATA_BASE
+#define CONFIG_SPL_BSS_MAX_SIZE 0x1080000
+
+/* memtest start addr */
+
+/* memtest will be run on 16MB */
+
+#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC (	\
+	DAVINCI_SYSCFG_SUSPSRC_TIMER0 |		\
+	DAVINCI_SYSCFG_SUSPSRC_SPI1 |		\
+	DAVINCI_SYSCFG_SUSPSRC_UART2 |		\
+	DAVINCI_SYSCFG_SUSPSRC_EMAC |		\
+	DAVINCI_SYSCFG_SUSPSRC_I2C)
+
+/*
+ * PLL configuration
+ */
+
+/* Requires CONFIG_SYS_DA850_PLL0_POSTDIV=0, set in Kconfig */
+#define CONFIG_SYS_DA850_PLL0_PLLM     18
+#define CONFIG_SYS_DA850_PLL1_PLLM     21
+
+/*
+ * DDR2 memory configuration
+ */
+#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
+					DV_DDR_PHY_EXT_STRBEN | \
+					(0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDBCR (		  \
+	(1 << DV_DDR_SDCR_DDR2EN_SHIFT)		| \
+	(1 << DV_DDR_SDCR_DDREN_SHIFT)		| \
+	(1 << DV_DDR_SDCR_SDRAMEN_SHIFT)	| \
+	(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT)	| \
+	(4 << DV_DDR_SDCR_CL_SHIFT)		| \
+	(3 << DV_DDR_SDCR_IBANK_SHIFT)		| \
+	(2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
+
+/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
+#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
+
+#define CONFIG_SYS_DA850_DDR2_SDTIMR (		  \
+	(19 << DV_DDR_SDTMR1_RFC_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_RP_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_RCD_SHIFT)		| \
+	(2 << DV_DDR_SDTMR1_WR_SHIFT)		| \
+	(6 << DV_DDR_SDTMR1_RAS_SHIFT)		| \
+	(8 << DV_DDR_SDTMR1_RC_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_RRD_SHIFT)		| \
+	(1 << DV_DDR_SDTMR1_WTR_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDTIMR2 (		  \
+	(7 << DV_DDR_SDTMR2_RASMAX_SHIFT)	| \
+	(2 << DV_DDR_SDTMR2_XP_SHIFT)		| \
+	(0 << DV_DDR_SDTMR2_ODT_SHIFT)		| \
+	(20 << DV_DDR_SDTMR2_XSNR_SHIFT)	| \
+	(199 << DV_DDR_SDTMR2_XSRD_SHIFT)	| \
+	(1 << DV_DDR_SDTMR2_RTP_SHIFT)		| \
+	(2 << DV_DDR_SDTMR2_CKE_SHIFT))
+
+#define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000492
+#define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
+
+/*
+ * Serial Driver info
+ */
+#define CONFIG_SYS_NS16550_CLK	clk_get(DAVINCI_UART2_CLKID)
+
+#define CONFIG_SYS_SPI_BASE		DAVINCI_SPI1_BASE
+#define CONFIG_SYS_SPI_CLK		clk_get(DAVINCI_SPI1_CLKID)
+
+/*
+ * I2C Configuration
+ */
+#define CONFIG_SYS_DAVINCI_I2C_SPEED	25000
+#define CONFIG_SYS_DAVINCI_I2C_SLAVE	10 /* Bogus, master-only in U-Boot */
+#define CONFIG_SYS_I2C_EXPANDER_ADDR	0x20
+
+/*
+ * Flash & Environment
+ */
+#ifdef CONFIG_MTD_RAW_NAND
+#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+#define	CONFIG_SYS_NAND_PAGE_2K
+#define CONFIG_SYS_NAND_CS		3
+#define CONFIG_SYS_NAND_BASE		DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
+#define CONFIG_SYS_NAND_MASK_CLE	0x10
+#define CONFIG_SYS_NAND_MASK_ALE	0x8
+#undef CONFIG_SYS_NAND_HW_ECC
+#define CONFIG_SYS_MAX_NAND_DEVICE	1 /* Max number of NAND devices */
+#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
+#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2 << 10)
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	SZ_512K
+#define CONFIG_SYS_NAND_U_BOOT_DST	0xc1080000
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP	(CONFIG_SYS_NAND_U_BOOT_DST - \
+					CONFIG_SYS_NAND_U_BOOT_SIZE - \
+					CONFIG_SYS_MALLOC_LEN -       \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_NAND_ECCPOS		{				\
+				6, 7, 8, 9, 10, 11, 12, 13, 14, 15,	\
+				22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
+				38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
+				54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	10
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SPL_NAND_LOAD
+#endif
+
+/*
+ * Network & Ethernet Configuration
+ */
+#ifdef CONFIG_DRIVER_TI_EMAC
+#define CONFIG_NET_RETRY_COUNT	10
+#endif
+
+/*
+ * U-Boot general configuration
+ */
+#define CONFIG_BOOTFILE		"zImage" /* Boot file name */
+#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR	(PHYS_SDRAM_1 + 0x700000)
+
+/*
+ * USB Configs
+ */
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS	15
+
+/*
+ * Linux Information
+ */
+#define LINUX_BOOT_PARAM_ADDR	(PHYS_SDRAM_1 + 0x100)
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_BOOTCOMMAND \
+		"run envboot; " \
+		"run mmcboot; "
+
+#define DEFAULT_LINUX_BOOT_ENV \
+	"loadaddr=0xc0700000\0" \
+	"fdtaddr=0xc0600000\0" \
+	"scriptaddr=0xc0600000\0"
+
+#include <environment/ti/mmc.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	DEFAULT_LINUX_BOOT_ENV \
+	DEFAULT_MMC_TI_ARGS \
+	"bootpart=0:2\0" \
+	"bootdir=/boot\0" \
+	"bootfile=zImage\0" \
+	"fdtfile=da850-lcdk.dtb\0" \
+	"boot_fdt=yes\0" \
+	"boot_fit=0\0" \
+	"console=ttyS2,115200n8\0"
+
+#ifdef CONFIG_CMD_BDI
+#define CONFIG_CLOCKS
+#endif
+
+/* SD/MMC */
+
+/* defines for SPL */
+#define CONFIG_SYS_SPL_MALLOC_START	(CONFIG_SYS_TEXT_BASE - \
+						CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_SPL_MALLOC_SIZE	CONFIG_SYS_MALLOC_LEN
+#define CONFIG_SPL_STACK	0x8001ff00
+#define CONFIG_SPL_MAX_FOOTPRINT	32768
+#define CONFIG_SPL_PAD_TO	32768
+
+/* additions for new relocation code, must added to all boards */
+#define CONFIG_SYS_SDRAM_BASE		0xc0000000
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
+					GENERATED_GBL_DATA_SIZE)
+
+#include <asm/arch/hardware.h>
+
+#endif /* __CONFIG_H */