Add submodule dependency filesHEADmaster

Change-Id: Iaf8d18082d3991dec7c0ebbea540f092188eb4ec

1 files changed, 315 insertions, 0 deletions

diff --git a/roms/u-boot/include/configs/vme8349.h b/roms/u-boot/include/configs/vme8349.h
new file mode 100644
index 000000000..20fcce187
--- /dev/null
+++ b/roms/u-boot/include/configs/vme8349.h
@@ -0,0 +1,315 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * esd vme8349 U-Boot configuration file
+ * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
+ *
+ * (C) Copyright 2006-2010
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * reinhard.arlt@esd-electronics.de
+ * Based on the MPC8349EMDS config.
+ */
+
+/*
+ * vme8349 board configuration file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 Family */
+
+/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
+#undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */
+
+#undef CONFIG_SYS_DRAM_TEST			/* memory test, takes time */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_DDR_ECC			/* only for ECC DDR module */
+#define CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
+#define CONFIG_SPD_EEPROM
+#define SPD_EEPROM_ADDRESS		0x54
+#define CONFIG_SYS_READ_SPD		vme8349_read_spd
+#define CONFIG_SYS_83XX_DDR_USES_CS0	/* esd; Fsl board uses CS2/CS3 */
+
+/*
+ * 32-bit data path mode.
+ *
+ * Please note that using this mode for devices with the real density of 64-bit
+ * effectively reduces the amount of available memory due to the effect of
+ * wrapping around while translating address to row/columns, for example in the
+ * 256MB module the upper 128MB get aliased with contents of the lower
+ * 128MB); normally this define should be used for devices with real 32-bit
+ * data path.
+ */
+#undef CONFIG_DDR_32BIT
+
+#define CONFIG_SYS_SDRAM_BASE		0x00000000	/* DDR is sys memory*/
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
+					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
+#define CONFIG_DDR_2T_TIMING
+#define CONFIG_SYS_DDRCDR		(DDRCDR_DHC_EN \
+					| DDRCDR_ODT \
+					| DDRCDR_Q_DRN)
+					/* 0x80080001 */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_BASE		0xf8000000	/* start of FLASH   */
+#define CONFIG_SYS_FLASH_SIZE		128		/* flash size in MB */
+
+
+#define CONFIG_SYS_WINDOW1_BASE		0xf0000000
+
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device*/
+
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase TO (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write TO (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xF7000000	/* Initial RAM addr */
+#define CONFIG_SYS_INIT_RAM_SIZE		0x1000		/* size */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					 GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB */
+#define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Malloc size */
+
+#undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE  \
+		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_IMMR + 0x4600)
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
+/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
+
+#define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */
+
+/* TSEC */
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
+
+#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
+#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
+#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
+#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */
+
+#if defined(CONFIG_PCI)
+
+
+#if !defined(CONFIG_PCI_PNP)
+	#define PCI_ENET0_IOADDR	0xFIXME
+	#define PCI_ENET0_MEMADDR	0xFIXME
+	#define PCI_IDSEL_NUMBER	0xFIXME
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */
+
+#endif	/* CONFIG_PCI */
+
+/*
+ * TSEC configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#define CONFIG_GMII			/* MII PHY management */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC1_NAME	"TSEC0"
+#define CONFIG_TSEC2
+#define CONFIG_TSEC2_NAME	"TSEC1"
+#define CONFIG_PHY_M88E1111
+#define TSEC1_PHY_ADDR		0x08
+#define TSEC2_PHY_ADDR		0x10
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME		"TSEC0"
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#ifndef CONFIG_SYS_RAMBOOT
+/* Address and size of Redundant Environment Sector	*/
+#endif
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+
+#define CONFIG_SYS_RTC_BUS_NUM  0x01
+#define CONFIG_SYS_I2C_RTC_ADDR	0x32
+
+/* Pass Ethernet MAC to VxWorks */
+#define CONFIG_SYS_VXWORKS_MAC_PTR	0x000043f0
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)	/* Init Memory map for Linux*/
+
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH 0
+#define CONFIG_SYS_SICRL SICRL_LDP_A
+
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR	0x00100000
+#define CONFIG_SYS_GPIO1_DAT	0x00100000
+
+#define CONFIG_SYS_GPIO2_PRELIM
+#define CONFIG_SYS_GPIO2_DIR	0x78900000
+#define CONFIG_SYS_GPIO2_DAT	0x70100000
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#endif
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#endif
+
+#define CONFIG_HOSTNAME		"VME8349"
+#define CONFIG_ROOTPATH		"/tftpboot/rootfs"
+#define CONFIG_BOOTFILE		"uImage"
+
+#define CONFIG_LOADADDR		800000	/* def location for tftp and bootm */
+
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"							\
+	"hostname=vme8349\0"						\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+	"flash_nfs=run nfsargs addip addtty;"				\
+		"bootm ${kernel_addr}\0"				\
+	"flash_self=run ramargs addip addtty;"				\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
+		"bootm\0"						\
+	"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"		\
+	"update=protect off fff00000 fff3ffff; "			\
+		"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
+	"upd=run load update\0"						\
+	"fdtaddr=780000\0"						\
+	"fdtfile=vme8349.dtb\0"						\
+	""
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv bootargs root=/dev/nfs rw "				\
+		"nfsroot=$serverip:$rootpath "				\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
+							"$netdev:off "	\
+		"console=$consoledev,$baudrate $othbootargs;"		\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND						\
+	"setenv bootargs root=/dev/ram rw "				\
+		"console=$consoledev,$baudrate $othbootargs;"		\
+	"tftp $ramdiskaddr $ramdiskfile;"				\
+	"tftp $loadaddr $bootfile;"					\
+	"tftp $fdtaddr $fdtfile;"					\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+#ifndef __ASSEMBLY__
+int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
+		     unsigned char *buffer, int len);
+#endif
+
+#endif	/* __CONFIG_H */