diff options
Diffstat (limited to 'roms/u-boot-sam460ex/include/configs/TASREG.h')
| -rw-r--r-- | roms/u-boot-sam460ex/include/configs/TASREG.h | 306 |
1 files changed, 306 insertions, 0 deletions
diff --git a/roms/u-boot-sam460ex/include/configs/TASREG.h b/roms/u-boot-sam460ex/include/configs/TASREG.h new file mode 100644 index 000000000..b69f015c7 --- /dev/null +++ b/roms/u-boot-sam460ex/include/configs/TASREG.h @@ -0,0 +1,306 @@ +/* + * Configuation settings for the esd TASREG board. + * + * (C) Copyright 2004 + * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _TASREG_H +#define _TASREG_H + +#ifndef __ASSEMBLY__ +#include <asm/m5249.h> +#endif + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_MCF52x2 /* define processor family */ +#define CONFIG_M5249 /* define processor type */ + +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + +#define CONFIG_MCFTMR + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT (0) +#define CONFIG_BAUDRATE 19200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#undef CONFIG_WATCHDOG + +#undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_BSP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C + +#undef CONFIG_CMD_NET + + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ +#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ + +#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ + +#define CONFIG_SYS_MEMTEST_START 0x400 +#define CONFIG_SYS_MEMTEST_END 0x380000 + +#define CONFIG_SYS_HZ 1000 + +/* + * Clock configuration: enable only one of the following options + */ + +#if 0 /* this setting will run the cpu at 11MHz */ +#define CONFIG_SYS_PLL_BYPASS 1 /* bypass PLL for test purpose */ +#undef CONFIG_SYS_FAST_CLK /* MCF5249 can run at 140MHz */ +#define CONFIG_SYS_CLK 11289600 /* PLL bypass */ +#endif + +#if 0 /* this setting will run the cpu at 70MHz */ +#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ +#undef CONFIG_SYS_FAST_CLK /* MCF5249 can run at 140MHz */ +#define CONFIG_SYS_CLK 72185018 /* The next lower speed */ +#endif + +#if 1 /* this setting will run the cpu at 140MHz */ +#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ +#define CONFIG_SYS_FAST_CLK 1 /* MCF5249 can run at 140MHz */ +#define CONFIG_SYS_CLK 132025600 /* MCF5249 can run at 140MHz */ +#endif + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ +#define CONFIG_SYS_MBAR2 0x80000000 + +/*----------------------------------------------------------------------- + * I2C + */ +#define CONFIG_SOFT_I2C +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ + /* 32 byte page write mode using*/ + /* last 5 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +#if defined (CONFIG_SOFT_I2C) +#if 0 /* push-pull */ +#define SDA 0x00800000 +#define SCL 0x00000008 +#define DIR0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN)) +#define DIR1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN)) +#define OUT0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT)) +#define OUT1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT)) +#define IN0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ)) +#define IN1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ)) +#define I2C_INIT {OUT1|=SDA;OUT0|=SCL;} +#define I2C_READ ((IN1&SDA)?1:0) +#define I2C_SDA(x) {if(x)OUT1|=SDA;else OUT1&=~SDA;} +#define I2C_SCL(x) {if(x)OUT0|=SCL;else OUT0&=~SCL;} +#define I2C_DELAY {udelay(5);} +#define I2C_ACTIVE {DIR1|=SDA;} +#define I2C_TRISTATE {DIR1&=~SDA;} +#else /* open-collector */ +#define SDA 0x00800000 +#define SCL 0x00000008 +#define DIR0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN)) +#define DIR1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN)) +#define OUT0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT)) +#define OUT1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT)) +#define IN0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ)) +#define IN1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ)) +#define I2C_INIT {DIR1&=~SDA;DIR0&=~SCL;OUT1&=~SDA;OUT0&=~SCL;} +#define I2C_READ ((IN1&SDA)?1:0) +#define I2C_SDA(x) {if(x)DIR1&=~SDA;else DIR1|=SDA;} +#define I2C_SCL(x) {if(x)DIR0&=~SCL;else DIR0|=SCL;} +#define I2C_DELAY {udelay(5);} +#define I2C_ACTIVE {DIR1|=SDA;} +#define I2C_TRISTATE {DIR1&=~SDA;} +#endif +#endif + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in internal SRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR 0xFFC40000 /* Address of Environment Sector*/ +#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ +#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE + +#if 0 /* test-only */ +#define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */ +#endif + +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) + +#define CONFIG_SYS_MONITOR_LEN 0x20000 +#define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */ +#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ +#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ +#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 16 + +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_END - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) +#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ + CF_CACR_DBWE) + +/*----------------------------------------------------------------------- + * Memory bank definitions + */ + +/* CS0 - AMD Flash, address 0xffc00000 */ +#define CONFIG_SYS_CS0_BASE 0xffc00000 +#define CONFIG_SYS_CS0_CTRL 0x00001980 /* WS=0110, AA=1, PS=10 */ +/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/ +#define CONFIG_SYS_CS0_MASK 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */ + +/* CS1 - FPGA, address 0xe0000000 */ +#define CONFIG_SYS_CS1_BASE 0xe0000000 +#define CONFIG_SYS_CS1_CTRL 0x00000d80 /* WS=0011, AA=1, PS=10 */ +#define CONFIG_SYS_CS1_MASK 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/ + +/*----------------------------------------------------------------------- + * Port configuration + */ +#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ +#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/ +#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ +#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ +#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ +#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ + +#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ + +/*----------------------------------------------------------------------- + * FPGA stuff + */ +#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CONFIG_SYS_FPGA_MAX_SIZE 512*1024 /* 512kByte is enough for XC2S200*/ + +/* FPGA program pin configuration */ +#define CONFIG_SYS_FPGA_PRG 0x00010000 /* FPGA program pin (ppc output) */ +#define CONFIG_SYS_FPGA_CLK 0x00040000 /* FPGA clk pin (ppc output) */ +#define CONFIG_SYS_FPGA_DATA 0x00020000 /* FPGA data pin (ppc output) */ +#define CONFIG_SYS_FPGA_INIT 0x00080000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE 0x00100000 /* FPGA done pin (ppc input) */ + +#endif /* _TASREG_H */ |