diff options
Diffstat (limited to 'roms/u-boot-sam460ex/include/configs/lwmon5.h')
| -rw-r--r-- | roms/u-boot-sam460ex/include/configs/lwmon5.h | 623 |
1 files changed, 623 insertions, 0 deletions
diff --git a/roms/u-boot-sam460ex/include/configs/lwmon5.h b/roms/u-boot-sam460ex/include/configs/lwmon5.h new file mode 100644 index 000000000..6461124e5 --- /dev/null +++ b/roms/u-boot-sam460ex/include/configs/lwmon5.h @@ -0,0 +1,623 @@ +/* + * (C) Copyright 2007-2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * lwmon5.h - configuration for lwmon5 board + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_LWMON5 1 /* Board is lwmon5 */ +#define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_440 1 /* ... PPC440 family */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */ +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ +#define CONFIG_BOARD_RESET 1 /* Call board_reset */ + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ + +#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#define CONFIG_SYS_LIME_BASE_0 0xc0000000 +#define CONFIG_SYS_LIME_BASE_1 0xc1000000 +#define CONFIG_SYS_LIME_BASE_2 0xc2000000 +#define CONFIG_SYS_LIME_BASE_3 0xc3000000 +#define CONFIG_SYS_FPGA_BASE_0 0xc4000000 +#define CONFIG_SYS_FPGA_BASE_1 0xc4200000 +#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ +#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 + +/* Don't change either of these */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ + +#define CONFIG_SYS_USB2D0_BASE 0xe0000100 +#define CONFIG_SYS_USB_DEVICE 0xe0000000 +#define CONFIG_SYS_USB_HOST 0xe0000400 + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer + *----------------------------------------------------------------------*/ +/* + * On LWMON5 we use D-cache as init-ram and stack pointer. We also move + * the POST_WORD from OCM to a 440EPx register that preserves it's + * content during reset (GPT0_COMP6). This way we reserve the OCM (16k) + * for logbuffer only. (GPT0_COMP1-COMP5 are reserved for logbuffer header.) + */ +#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data*/ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_POST_ALT_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) + /* unused GPT0 COMP reg */ +#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ + /* 440EPx errata CHIP 11 */ +#define CONFIG_SYS_OCM_SIZE (16 << 10) + +/* Additional registers for watchdog timer post test */ + +#define CONFIG_SYS_WATCHDOG_TIME_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK2) +#define CONFIG_SYS_WATCHDOG_FLAGS_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK1) +#define CONFIG_SYS_DSPIC_TEST_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR +#define CONFIG_SYS_OCM_STATUS_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR +#define CONFIG_SYS_WATCHDOG_MAGIC 0x12480000 +#define CONFIG_SYS_WATCHDOG_MAGIC_MASK 0xFFFF0000 +#define CONFIG_SYS_DSPIC_TEST_MASK 0x00000001 +#define CONFIG_SYS_OCM_STATUS_OK 0x00009A00 +#define CONFIG_SYS_OCM_STATUS_FAIL 0x0000A300 +#define CONFIG_SYS_OCM_STATUS_MASK 0x0000FF00 + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 +/* define this if you want console on UART1 */ +#define CONFIG_UART1_CONSOLE 1 /* use UART1 as console */ + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CONFIG_SYS_FLASH0 0xFC000000 +#define CONFIG_SYS_FLASH1 0xF8000000 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ +#define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */ +#define CONFIG_DDR_DATA_EYE 1 /* use DDR2 optimization */ +#define CONFIG_DDR_ECC 1 /* enable ECC */ +#define CONFIG_SYS_POST_ECC_ON CONFIG_SYS_POST_ECC + +/* POST support */ +#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_ECC_ON | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_FPU | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_OCM | \ + CONFIG_SYS_POST_RTC | \ + CONFIG_SYS_POST_SPR | \ + CONFIG_SYS_POST_UART | \ + CONFIG_SYS_POST_SYSMON | \ + CONFIG_SYS_POST_WATCHDOG | \ + CONFIG_SYS_POST_DSP | \ + CONFIG_SYS_POST_BSPEC1 | \ + CONFIG_SYS_POST_BSPEC2 | \ + CONFIG_SYS_POST_BSPEC3 | \ + CONFIG_SYS_POST_BSPEC4 | \ + CONFIG_SYS_POST_BSPEC5) + +#define CONFIG_POST_WATCHDOG {\ + "Watchdog timer test", \ + "watchdog", \ + "This test checks the watchdog timer.", \ + POST_RAM | POST_POWERON | POST_SLOWTEST | POST_MANUAL | POST_REBOOT, \ + &lwmon5_watchdog_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_WATCHDOG \ + } + +#define CONFIG_POST_BSPEC1 {\ + "dsPIC init test", \ + "dspic_init", \ + "This test returns result of dsPIC READY test run earlier.", \ + POST_RAM | POST_ALWAYS, \ + &dspic_init_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC1 \ + } + +#define CONFIG_POST_BSPEC2 {\ + "dsPIC test", \ + "dspic", \ + "This test gets result of dsPIC POST and dsPIC version.", \ + POST_RAM | POST_ALWAYS, \ + &dspic_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC2 \ + } + +#define CONFIG_POST_BSPEC3 {\ + "FPGA test", \ + "fpga", \ + "This test checks FPGA registers and memory.", \ + POST_RAM | POST_ALWAYS, \ + &fpga_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC3 \ + } + +#define CONFIG_POST_BSPEC4 {\ + "GDC test", \ + "gdc", \ + "This test checks GDC registers and memory.", \ + POST_RAM | POST_ALWAYS, \ + &gdc_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC4 \ + } + +#define CONFIG_POST_BSPEC5 {\ + "SYSMON1 test", \ + "sysmon1", \ + "This test checks GPIO_62_EPX pin indicating power failure.", \ + POST_RAM | POST_MANUAL | POST_NORMAL | POST_SLOWTEST, \ + &sysmon1_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC5 \ + } + +#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ +#define CONFIG_LOGBUFFER +/* Reserve GPT0_COMP1-COMP5 for logbuffer header */ +#define CONFIG_ALT_LH_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP1) +#define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE) +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */ +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ + /* 64 byte page write mode using*/ + /* last 6 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +#define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ +#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ +#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ + +#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ +#if 0 +#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ +#define CONFIG_AUTOBOOT_PROMPT \ + "\nEnter password - autoboot in %d sec...\n", bootdelay +#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ +#endif + +#define CONFIG_PREBOOT "setenv bootdelay 15" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hostname=lwmon5\0" \ + "netdev=eth0\0" \ + "unlock=yes\0" \ + "logversion=2\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ + "addmisc=setenv bootargs ${bootargs} rtc-pcf8563.probe=0,0x51\0"\ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addtty addmisc;bootm\0" \ + "rootpath=/opt/eldk/ppc_4xxFP\0" \ + "bootfile=/tftpboot/lwmon5/uImage\0" \ + "kernel_addr=FC000000\0" \ + "ramdisk_addr=FC180000\0" \ + "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ + "update=protect off FFF80000 FFFFFFFF;era FFF80000 FFFFFFFF;" \ + "cp.b 200000 FFF80000 80000\0" \ + "upd=run load update\0" \ + "lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \ + "source 200000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 3 /* PHY address, See schematics */ + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 300 + +#define CONFIG_HAS_ETH0 +#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 1 + +/* Video console */ +#define CONFIG_VIDEO +#define CONFIG_VIDEO_MB862xx +#define CONFIG_VIDEO_MB862xx_ACCEL +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_LOGO +#define CONFIG_CONSOLE_EXTRA_INFO +#define VIDEO_FB_16BPP_PIXEL_SWAP +#define VIDEO_FB_16BPP_WORD_SWAP + +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_SPLASH_SCREEN + +/* USB */ +#ifdef CONFIG_440EPX +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/* Comment this out to enable USB 1.1 device */ +#define USB_2_0_DEVICE + +#endif /* CONFIG_440EPX */ + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_LOG +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SDRAM + +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP +#endif + +#ifdef CONFIG_440EPX +#define CONFIG_CMD_USB +#endif + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CONFIG_SUPPORT_VFAT + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ + +#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------*/ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/ + +/* Board-specific PCI */ +#define CONFIG_SYS_PCI_TARGET_INIT +#define CONFIG_SYS_PCI_MASTER_INIT + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ + +#define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */ +#define CONFIG_WD_PERIOD 40000 /* in usec */ +#define CONFIG_WD_MAX_RATE 66600 /* in ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x03050200 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xfc000) + +/* Memory Bank 1 (Lime) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x01004380 +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xdc000) + +/* Memory Bank 2 (FPGA) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x01004400 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE_0 | 0x1c000) + +/* Memory Bank 3 (FPGA2) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x01004400 +#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FPGA_BASE_1 | 0x1c000) + +#define CONFIG_SYS_EBC_CFG 0xb8400000 + +/*----------------------------------------------------------------------- + * Graphics (Fujitsu Lime) + *----------------------------------------------------------------------*/ +/* Lime Clock frequency is to set 100MHz */ +#define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000 +#if 0 +/* Lime Clock frequency for 133MHz */ +#define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000 +#endif + +/* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars + and pixel flare on display when 133MHz was configured. According to + SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */ +#ifdef CONFIG_SYS_LIME_CLOCK_133MHZ +#define CONFIG_SYS_MB862xx_MMR 0x414FB7F3 +#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_133MHZ +#else +#define CONFIG_SYS_MB862xx_MMR 0x414FB7F2 +#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_100MHZ +#endif + +/*----------------------------------------------------------------------- + * GPIO Setup + *----------------------------------------------------------------------*/ +#define CONFIG_SYS_GPIO_PHY1_RST 12 +#define CONFIG_SYS_GPIO_FLASH_WP 14 +#define CONFIG_SYS_GPIO_PHY0_RST 22 +#define CONFIG_SYS_GPIO_DSPIC_READY 51 +#define CONFIG_SYS_GPIO_EEPROM_EXT_WP 55 +#define CONFIG_SYS_GPIO_HIGHSIDE 56 +#define CONFIG_SYS_GPIO_EEPROM_INT_WP 57 +#define CONFIG_SYS_GPIO_BOARD_RESET 58 +#define CONFIG_SYS_GPIO_LIME_S 59 +#define CONFIG_SYS_GPIO_LIME_RST 60 +#define CONFIG_SYS_GPIO_SYSMON_STATUS 62 +#define CONFIG_SYS_GPIO_WATCHDOG 63 + +/*----------------------------------------------------------------------- + * PPC440 GPIO Configuration + */ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +{ \ +/* GPIO Core 0 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO15 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMCTxD(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMCTxD(5) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMCTxD(6) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMCTxD(7) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 GMCTxD(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 GMCTxD(3) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \ +}, \ +{ \ +/* GPIO Core 1 */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO49 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO57 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \ +} \ +} + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ |