diff options
Diffstat (limited to 'roms/u-boot/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi')
| -rw-r--r-- | roms/u-boot/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi | 196 |
1 files changed, 196 insertions, 0 deletions
diff --git a/roms/u-boot/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi b/roms/u-boot/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi new file mode 100644 index 000000000..678761929 --- /dev/null +++ b/roms/u-boot/arch/arm/dts/stm32mp157a-dk1-u-boot.dtsi @@ -0,0 +1,196 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright : STMicroelectronics 2018 + */ + +#include <dt-bindings/clock/stm32mp1-clksrc.h> +#include "stm32mp15-u-boot.dtsi" +#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi" + +/ { + aliases { + i2c3 = &i2c4; + mmc0 = &sdmmc1; + usb0 = &usbotg_hs; + }; + config { + u-boot,boot-led = "heartbeat"; + u-boot,error-led = "error"; + u-boot,mmc-env-partition = "ssbl"; + st,adc_usb_pd = <&adc1 18>, <&adc1 19>; + st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; + st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>; + }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + }; + + reserved-memory { + optee@de000000 { + reg = <0xde000000 0x02000000>; + no-map; + }; + }; + + led { + red { + label = "error"; + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; + default-state = "off"; + status = "okay"; + }; + }; +}; + +&adc { + status = "okay"; +}; + +&clk_hse { + st,digbypass; +}; + +&i2c4 { + u-boot,dm-pre-reloc; +}; + +&i2c4_pins_a { + u-boot,dm-pre-reloc; + pins { + u-boot,dm-pre-reloc; + }; +}; + +&pmic { + u-boot,dm-pre-reloc; +}; + +&rcc { + st,clksrc = < + CLK_MPU_PLL1P + CLK_AXI_PLL2P + CLK_MCU_PLL3P + CLK_PLL12_HSE + CLK_PLL3_HSE + CLK_PLL4_HSE + CLK_RTC_LSE + CLK_MCO1_DISABLED + CLK_MCO2_DISABLED + >; + + st,clkdiv = < + 1 /*MPU*/ + 0 /*AXI*/ + 0 /*MCU*/ + 1 /*APB1*/ + 1 /*APB2*/ + 1 /*APB3*/ + 1 /*APB4*/ + 2 /*APB5*/ + 23 /*RTC*/ + 0 /*MCO1*/ + 0 /*MCO2*/ + >; + + st,pkcs = < + CLK_CKPER_HSE + CLK_FMC_ACLK + CLK_QSPI_ACLK + CLK_ETH_DISABLED + CLK_SDMMC12_PLL4P + CLK_DSI_DSIPLL + CLK_STGEN_HSE + CLK_USBPHY_HSE + CLK_SPI2S1_PLL3Q + CLK_SPI2S23_PLL3Q + CLK_SPI45_HSI + CLK_SPI6_HSI + CLK_I2C46_HSI + CLK_SDMMC3_PLL4P + CLK_USBO_USBPHY + CLK_ADC_CKPER + CLK_CEC_LSE + CLK_I2C12_HSI + CLK_I2C35_HSI + CLK_UART1_HSI + CLK_UART24_HSI + CLK_UART35_HSI + CLK_UART6_HSI + CLK_UART78_HSI + CLK_SPDIF_PLL4P + CLK_FDCAN_PLL4R + CLK_SAI1_PLL3Q + CLK_SAI2_PLL3Q + CLK_SAI3_PLL3Q + CLK_SAI4_PLL3Q + CLK_RNG1_LSI + CLK_RNG2_LSI + CLK_LPTIM1_PCLK1 + CLK_LPTIM23_PCLK3 + CLK_LPTIM45_LSE + >; + + /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */ + pll2: st,pll@1 { + compatible = "st,stm32mp1-pll"; + reg = <1>; + cfg = < 2 65 1 0 0 PQR(1,1,1) >; + frac = < 0x1400 >; + u-boot,dm-pre-reloc; + }; + + /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */ + pll3: st,pll@2 { + compatible = "st,stm32mp1-pll"; + reg = <2>; + cfg = < 1 33 1 16 36 PQR(1,1,1) >; + frac = < 0x1a04 >; + u-boot,dm-pre-reloc; + }; + + /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */ + pll4: st,pll@3 { + compatible = "st,stm32mp1-pll"; + reg = <3>; + cfg = < 3 98 5 7 7 PQR(1,1,1) >; + u-boot,dm-pre-reloc; + }; +}; + +&sdmmc1 { + u-boot,dm-spl; +}; + +&sdmmc1_b4_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&uart4 { + u-boot,dm-pre-reloc; +}; + +&uart4_pins_a { + u-boot,dm-pre-reloc; + pins1 { + u-boot,dm-pre-reloc; + }; + pins2 { + u-boot,dm-pre-reloc; + /* pull-up on rx to avoid floating level */ + bias-pull-up; + }; +}; + +&usbotg_hs { + u-boot,force-b-session-valid; +}; |