diff options
Diffstat (limited to 'roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi')
| -rw-r--r-- | roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi | 282 |
1 files changed, 282 insertions, 0 deletions
diff --git a/roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi b/roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi new file mode 100644 index 000000000..11bc24706 --- /dev/null +++ b/roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom-u-boot.dtsi @@ -0,0 +1,282 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright (C) 2019 Marek Vasut <marex@denx.de> + */ + +#include <dt-bindings/clock/stm32mp1-clksrc.h> +#include "stm32mp15-u-boot.dtsi" +#include "stm32mp15-ddr3-dhsom-2x1Gb-1066-binG.dtsi" +#include "stm32mp15-ddr3-dhsom-2x2Gb-1066-binG.dtsi" +#include "stm32mp15-ddr3-dhsom-2x4Gb-1066-binG.dtsi" + +/ { + aliases { + i2c1 = &i2c2; + i2c3 = &i2c4; + i2c4 = &i2c5; + mmc0 = &sdmmc1; + mmc1 = &sdmmc2; + spi0 = &qspi; + usb0 = &usbotg_hs; + ethernet1 = &ksz8851; + }; + + config { + u-boot,boot-led = "heartbeat"; + u-boot,error-led = "error"; + st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; + st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>; + dh,som-coding-gpios = <&gpiof 12 0>, <&gpiof 13 0>, <&gpiof 15 0>; + dh,ddr3-coding-gpios = <&gpioz 6 0>, <&gpioz 7 0>; + }; + + led { + red { + label = "error"; + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; + default-state = "off"; + status = "okay"; + }; + + blue { + default-state = "on"; + }; + }; + + /* This is actually on FMC2, but we do not have bus driver for that */ + ksz8851: ks8851mll@64000000 { + compatible = "micrel,ks8851-mll"; + reg = <0x64000000 0x20000>; + }; +}; + +&gpiof { + snor-nwp { + gpio-hog; + gpios = <7 0>; + output-high; + line-name = "spi-nor-nwp"; + }; +}; + +&i2c4 { + u-boot,dm-pre-reloc; +}; + +&i2c4_pins_a { + u-boot,dm-pre-reloc; + pins { + u-boot,dm-pre-reloc; + }; +}; + +&pinctrl { + /* These should bound to FMC2 bus driver, but we do not have one */ + pinctrl-0 = <&fmc_pins_b &mco2_pins_a>; + pinctrl-1 = <&fmc_sleep_pins_b &mco2_sleep_pins_a>; + pinctrl-names = "default", "sleep"; + + mco2_pins_a: mco2-0 { + pins { + pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + }; + + mco2_sleep_pins_a: mco2-sleep-0 { + pins { + pinmux = <STM32_PINMUX('G', 2, ANALOG)>; /* MCO2 */ + }; + }; +}; + +&pmic { + u-boot,dm-pre-reloc; +}; + +&flash0 { + u-boot,dm-spl; +}; + +&qspi { + u-boot,dm-spl; +}; + +&qspi_clk_pins_a { + u-boot,dm-spl; + pins { + u-boot,dm-spl; + }; +}; + +&qspi_bk1_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&qspi_bk2_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&rcc { + st,clksrc = < + CLK_MPU_PLL1P + CLK_AXI_PLL2P + CLK_MCU_PLL3P + CLK_PLL12_HSE + CLK_PLL3_HSE + CLK_PLL4_HSE + CLK_RTC_LSE + CLK_MCO1_DISABLED + CLK_MCO2_PLL4P + >; + + st,clkdiv = < + 1 /*MPU*/ + 0 /*AXI*/ + 0 /*MCU*/ + 1 /*APB1*/ + 1 /*APB2*/ + 1 /*APB3*/ + 1 /*APB4*/ + 2 /*APB5*/ + 23 /*RTC*/ + 0 /*MCO1*/ + 1 /*MCO2*/ + >; + + st,pkcs = < + CLK_CKPER_HSE + CLK_FMC_ACLK + CLK_QSPI_ACLK + CLK_ETH_PLL4P + CLK_SDMMC12_PLL4P + CLK_DSI_DSIPLL + CLK_STGEN_HSE + CLK_USBPHY_HSE + CLK_SPI2S1_PLL3Q + CLK_SPI2S23_PLL3Q + CLK_SPI45_HSI + CLK_SPI6_HSI + CLK_I2C46_HSI + CLK_SDMMC3_PLL4P + CLK_USBO_USBPHY + CLK_ADC_CKPER + CLK_CEC_LSE + CLK_I2C12_HSI + CLK_I2C35_HSI + CLK_UART1_HSI + CLK_UART24_HSI + CLK_UART35_HSI + CLK_UART6_HSI + CLK_UART78_HSI + CLK_SPDIF_PLL4P + CLK_FDCAN_PLL4R + CLK_SAI1_PLL3Q + CLK_SAI2_PLL3Q + CLK_SAI3_PLL3Q + CLK_SAI4_PLL3Q + CLK_RNG1_LSI + CLK_RNG2_LSI + CLK_LPTIM1_PCLK1 + CLK_LPTIM23_PCLK3 + CLK_LPTIM45_LSE + >; + + /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */ + pll2: st,pll@1 { + compatible = "st,stm32mp1-pll"; + reg = <1>; + cfg = < 2 65 1 0 0 PQR(1,1,1) >; + frac = < 0x1400 >; + u-boot,dm-pre-reloc; + }; + + /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */ + pll3: st,pll@2 { + compatible = "st,stm32mp1-pll"; + reg = <2>; + cfg = < 1 33 1 16 36 PQR(1,1,1) >; + frac = < 0x1a04 >; + u-boot,dm-pre-reloc; + }; + + /* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */ + pll4: st,pll@3 { + compatible = "st,stm32mp1-pll"; + reg = <3>; + cfg = < 1 49 5 11 11 PQR(1,1,1) >; + u-boot,dm-pre-reloc; + }; +}; + +&sdmmc1 { + u-boot,dm-spl; +}; + +&sdmmc1_b4_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&sdmmc1_dir_pins_a { + u-boot,dm-spl; + pins1 { + u-boot,dm-spl; + }; + pins2 { + u-boot,dm-spl; + }; +}; + +&sdmmc2 { + u-boot,dm-spl; +}; + +&sdmmc2_b4_pins_a { + u-boot,dm-spl; + pins { + u-boot,dm-spl; + }; +}; + +&sdmmc2_d47_pins_a { + u-boot,dm-spl; + pins { + u-boot,dm-spl; + }; +}; + +&uart4 { + u-boot,dm-pre-reloc; +}; + +&uart4_pins_a { + u-boot,dm-pre-reloc; + pins1 { + u-boot,dm-pre-reloc; + }; + pins2 { + u-boot,dm-pre-reloc; + /* pull-up on rx to avoid floating level */ + bias-pull-up; + }; +}; |