diff options
Diffstat (limited to 'roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom.dtsi')
| -rw-r--r-- | roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom.dtsi | 456 |
1 files changed, 456 insertions, 0 deletions
diff --git a/roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom.dtsi b/roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom.dtsi new file mode 100644 index 000000000..a1d1b8dec --- /dev/null +++ b/roms/u-boot/arch/arm/dts/stm32mp15xx-dhcom.dtsi @@ -0,0 +1,456 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (C) 2019 Marek Vasut <marex@denx.de> + */ +/dts-v1/; + +#include "stm32mp157.dtsi" +#include "stm32mp15xc.dtsi" +#include "stm32mp15-pinctrl.dtsi" +#include "stm32mp15xxaa-pinctrl.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/mfd/st,stpmic1.h> + +/ { + aliases { + eeprom0 = &eeprom0; + ethernet0 = ðernet0; + }; + + memory@c0000000 { + device_type = "memory"; + reg = <0xC0000000 0x40000000>; + }; + + ethernet_vio: vioregulator { + compatible = "regulator-fixed"; + regulator-name = "vio"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpiog 3 GPIO_ACTIVE_LOW>; + regulator-always-on; + regulator-boot-on; + }; +}; + +&cec { + pinctrl-names = "default"; + pinctrl-0 = <&cec_pins_a>; + status = "okay"; +}; + +&dcmi { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dcmi_pins_a>; + pinctrl-1 = <&dcmi_sleep_pins_a>; +}; + +&dts { + status = "okay"; +}; + +ðernet0 { + status = "okay"; + pinctrl-0 = <ðernet0_rmii_pins_a>; + pinctrl-1 = <ðernet0_rmii_pins_sleep_a>; + pinctrl-names = "default", "sleep"; + phy-mode = "rmii"; + max-speed = <100>; + phy-handle = <&phy0>; + phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + + phy0: ethernet-phy@1 { + reg = <1>; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + + pmic: stpmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + status = "okay"; + + regulators { + compatible = "st,stpmic1-regulators"; + ldo1-supply = <&v3v3>; + ldo2-supply = <&v3v3>; + ldo3-supply = <&vdd_ddr>; + ldo5-supply = <&v3v3>; + ldo6-supply = <&v3v3>; + pwr_sw1-supply = <&bst_out>; + pwr_sw2-supply = <&bst_out>; + + vddcore: buck1 { + regulator-name = "vddcore"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd_ddr: buck2 { + regulator-name = "vdd_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + st,mask-reset; + regulator-initial-mode = <0>; + regulator-over-current-protection; + }; + + v3v3: buck4 { + regulator-name = "v3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-over-current-protection; + regulator-initial-mode = <0>; + }; + + vdda: ldo1 { + regulator-name = "vdda"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO1 0>; + }; + + v2v8: ldo2 { + regulator-name = "v2v8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + interrupts = <IT_CURLIM_LDO2 0>; + }; + + vtt_ddr: ldo3 { + regulator-name = "vtt_ddr"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <750000>; + regulator-always-on; + regulator-over-current-protection; + }; + + vdd_usb: ldo4 { + regulator-name = "vdd_usb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + interrupts = <IT_CURLIM_LDO4 0>; + }; + + vdd_sd: ldo5 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + interrupts = <IT_CURLIM_LDO5 0>; + regulator-boot-on; + }; + + v1v8: ldo6 { + regulator-name = "v1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + interrupts = <IT_CURLIM_LDO6 0>; + }; + + vref_ddr: vref_ddr { + regulator-name = "vref_ddr"; + regulator-always-on; + regulator-over-current-protection; + }; + + bst_out: boost { + regulator-name = "bst_out"; + interrupts = <IT_OCP_BOOST 0>; + }; + + vbus_otg: pwr_sw1 { + regulator-name = "vbus_otg"; + interrupts = <IT_OCP_OTG 0>; + }; + + vbus_sw: pwr_sw2 { + regulator-name = "vbus_sw"; + interrupts = <IT_OCP_SWOUT 0>; + regulator-active-discharge; + }; + }; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + status = "okay"; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + status = "disabled"; + }; + }; + + eeprom0: eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; +}; + +&i2c5 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; +}; + +&ipcc { + status = "okay"; +}; + +&iwdg2 { + timeout-sec = <32>; + status = "okay"; +}; + +&m4_rproc { + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>; + mbox-names = "vq0", "vq1", "shutdown"; + status = "okay"; +}; + +&pwr_regulators { + vdd-supply = <&vdd>; + vdd_3v3_usbfs-supply = <&vdd_usb>; +}; + +&pinctrl { + ethernet0_rmii_pins_a: rmii-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */ + <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */ + <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */ + <STM32_PINMUX('A', 1, AF11)>, /* ETH1_RMII_REF_CLK */ + <STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */ + <STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + pins2 { + pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */ + <STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */ + <STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */ + bias-disable; + }; + }; + + ethernet0_rmii_pins_sleep_a: rmii-sleep-0 { + pins1 { + pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */ + <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */ + <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */ + <STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */ + <STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */ + <STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */ + <STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */ + <STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */ + <STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */ + }; + }; +}; + +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: mx66l51235l@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&rng1 { + status = "okay"; +}; + +&rtc { + status = "okay"; +}; + +&sdmmc1 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>; + cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + disable-wp; + st,sig-dir; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&vdd_sd>; + status = "okay"; +}; + +&sdmmc1_b4_pins_a { + /* + * SD bus pull-up resistors: + * - optional on SoMs with SD voltage translator + * - mandatory on SoMs without SD voltage translator + */ + pins1 { + bias-pull-up; + }; + pins2 { + bias-pull-up; + }; +}; + +&sdmmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>; + non-removable; + no-sd; + no-sdio; + st,sig-dir; + st,neg-edge; + bus-width = <8>; + vmmc-supply = <&v3v3>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_a>; + status = "disabled"; +}; + +&timers2 { + /* spare dmas for other usage (un-delete to enable pwm capture) */ + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; + pwm { + pinctrl-0 = <&pwm2_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + timer@1 { + status = "okay"; + }; +}; + +&timers6 { + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + timer@5 { + status = "okay"; + }; +}; + +&timers8 { + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; + pwm { + pinctrl-0 = <&pwm8_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + timer@7 { + status = "okay"; + }; +}; + +&timers12 { + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; + pwm { + pinctrl-0 = <&pwm12_pins_a>; + pinctrl-names = "default"; + status = "okay"; + }; + timer@11 { + status = "okay"; + }; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&uart4_pins_a>; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + dr_mode = "peripheral"; + phys = <&usbphyc_port1 0>; + phy-names = "usb2-phy"; + vbus-supply = <&vbus_otg>; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; +}; |