1 files changed, 392 insertions, 0 deletions
diff --git a/roms/u-boot/arch/arm/mach-at91/mpddrc.c b/roms/u-boot/arch/arm/mach-at91/mpddrc.c
new file mode 100644
index 000000000..5422c0545
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-at91/mpddrc.c
@@ -0,0 +1,392 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2013 Atmel Corporation
+ *		      Bo Shen <voice.shen@atmel.com>
+ *
+ * Copyright (C) 2015 Atmel Corporation
+ *		      Wenyou Yang <wenyou.yang@atmel.com>
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/atmel_mpddrc.h>
+#include <asm/arch/at91_common.h>
+#include <linux/delay.h>
+
+#define SAMA5D3_MPDDRC_VERSION		0x140
+
+static inline void atmel_mpddr_op(const struct atmel_mpddr *mpddr,
+	      int mode,
+	      u32 ram_address)
+{
+	writel(mode, &mpddr->mr);
+	dmb();
+	writel(0, ram_address);
+}
+
+static int ddr2_decodtype_is_seq(const unsigned int base, u32 cr)
+{
+	struct atmel_mpddr *mpddr = (struct atmel_mpddr *)base;
+	u16 version = readl(&mpddr->version) & 0xffff;
+
+	if ((version >= SAMA5D3_MPDDRC_VERSION) &&
+	    (cr & ATMEL_MPDDRC_CR_DECOD_INTERLEAVED))
+		return 0;
+
+	return 1;
+}
+
+
+int ddr2_init(const unsigned int base,
+	      const unsigned int ram_address,
+	      const struct atmel_mpddrc_config *mpddr_value)
+{
+	const struct atmel_mpddr *mpddr = (struct atmel_mpddr *)base;
+
+	u32 ba_off, cr;
+
+	/* Compute bank offset according to NC in configuration register */
+	ba_off = (mpddr_value->cr & ATMEL_MPDDRC_CR_NC_MASK) + 9;
+	if (ddr2_decodtype_is_seq(base, mpddr_value->cr))
+		ba_off += ((mpddr_value->cr & ATMEL_MPDDRC_CR_NR_MASK) >> 2) + 11;
+
+	ba_off += (mpddr_value->md & ATMEL_MPDDRC_MD_DBW_MASK) ? 1 : 2;
+
+	/* Program the memory device type into the memory device register */
+	writel(mpddr_value->md, &mpddr->md);
+
+	/* Program the configuration register */
+	writel(mpddr_value->cr, &mpddr->cr);
+
+	/* Program the timing register */
+	writel(mpddr_value->tpr0, &mpddr->tpr0);
+	writel(mpddr_value->tpr1, &mpddr->tpr1);
+	writel(mpddr_value->tpr2, &mpddr->tpr2);
+
+	/* Issue a NOP command */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+	/* A 200 us is provided to precede any signal toggle */
+	udelay(200);
+
+	/* Issue a NOP command */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+	/* Issue an all banks precharge command */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_PRCGALL_CMD, ram_address);
+
+	/* Issue an extended mode register set(EMRS2) to choose operation */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x2 << ba_off));
+
+	/* Issue an extended mode register set(EMRS3) to set EMSR to 0 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x3 << ba_off));
+
+	/*
+	 * Issue an extended mode register set(EMRS1) to enable DLL and
+	 * program D.I.C (output driver impedance control)
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x1 << ba_off));
+
+	/* Enable DLL reset */
+	cr = readl(&mpddr->cr);
+	writel(cr | ATMEL_MPDDRC_CR_DLL_RESET_ENABLED, &mpddr->cr);
+
+	/* A mode register set(MRS) cycle is issued to reset DLL */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LMR_CMD, ram_address);
+
+	/* Issue an all banks precharge command */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_PRCGALL_CMD, ram_address);
+
+	/* Two auto-refresh (CBR) cycles are provided */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_RFSH_CMD, ram_address);
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_RFSH_CMD, ram_address);
+
+	/* Disable DLL reset */
+	cr = readl(&mpddr->cr);
+	writel(cr & (~ATMEL_MPDDRC_CR_DLL_RESET_ENABLED), &mpddr->cr);
+
+	/* A mode register set (MRS) cycle is issued to disable DLL reset */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LMR_CMD, ram_address);
+
+	/* Set OCD calibration in default state */
+	cr = readl(&mpddr->cr);
+	writel(cr | ATMEL_MPDDRC_CR_OCD_DEFAULT, &mpddr->cr);
+
+	/*
+	 * An extended mode register set (EMRS1) cycle is issued
+	 * to OCD default value
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x1 << ba_off));
+
+	 /* OCD calibration mode exit */
+	cr = readl(&mpddr->cr);
+	writel(cr & (~ATMEL_MPDDRC_CR_OCD_DEFAULT), &mpddr->cr);
+
+	/*
+	 * An extended mode register set (EMRS1) cycle is issued
+	 * to enable OCD exit
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x1 << ba_off));
+
+	/* A nornal mode command is provided */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NORMAL_CMD, ram_address);
+
+	/* Perform a write access to any DDR2-SDRAM address */
+	writel(0, ram_address);
+
+	/* Write the refresh rate */
+	writel(mpddr_value->rtr, &mpddr->rtr);
+
+	return 0;
+}
+
+int ddr3_init(const unsigned int base,
+	      const unsigned int ram_address,
+	      const struct atmel_mpddrc_config *mpddr_value)
+{
+	struct atmel_mpddr *mpddr = (struct atmel_mpddr *)base;
+	u32 ba_off;
+
+	/* Compute bank offset according to NC in configuration register */
+	ba_off = (mpddr_value->cr & ATMEL_MPDDRC_CR_NC_MASK) + 9;
+	if (ddr2_decodtype_is_seq(base, mpddr_value->cr))
+		ba_off += ((mpddr_value->cr &
+			   ATMEL_MPDDRC_CR_NR_MASK) >> 2) + 11;
+
+	ba_off += (mpddr_value->md & ATMEL_MPDDRC_MD_DBW_MASK) ? 1 : 2;
+
+	/* Program the memory device type */
+	writel(mpddr_value->md, &mpddr->md);
+
+	/*
+	 * Program features of the DDR3-SDRAM device and timing parameters
+	 */
+	writel(mpddr_value->cr, &mpddr->cr);
+
+	writel(mpddr_value->tpr0, &mpddr->tpr0);
+	writel(mpddr_value->tpr1, &mpddr->tpr1);
+	writel(mpddr_value->tpr2, &mpddr->tpr2);
+
+	/* A NOP command is issued to the DDR3-SRAM */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+	/* A pause of at least 500us must be observed before a single toggle. */
+	udelay(500);
+
+	/* A NOP command is issued to the DDR3-SDRAM */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+	/*
+	 * An Extended Mode Register Set (EMRS2) cycle is issued to choose
+	 * between commercial or high temperature operations.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x2 << ba_off));
+	/*
+	 * Step 7: An Extended Mode Register Set (EMRS3) cycle is issued to set
+	 * the Extended Mode Register to 0.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x3 << ba_off));
+	/*
+	 * An Extended Mode Register Set (EMRS1) cycle is issued to disable and
+	 * to program O.D.S. (Output Driver Strength).
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
+		       ram_address + (0x1 << ba_off));
+
+	/*
+	 * Write a one to the DLL bit (enable DLL reset) in the MPDDRC
+	 * Configuration Register.
+	 */
+
+	/* A Mode Register Set (MRS) cycle is issued to reset DLL. */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LMR_CMD, ram_address);
+
+	udelay(50);
+
+	/*
+	 * A Calibration command (MRS) is issued to calibrate RTT and RON
+	 * values for the Process Voltage Temperature (PVT).
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_DEEP_CMD, ram_address);
+
+	/* A Normal Mode command is provided. */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NORMAL_CMD, ram_address);
+
+	/* Perform a write access to any DDR3-SDRAM address. */
+	writel(0, ram_address);
+
+	/*
+	 * Write the refresh rate into the COUNT field in the MPDDRC
+	 * Refresh Timer Register (MPDDRC_RTR):
+	 */
+	writel(mpddr_value->rtr, &mpddr->rtr);
+
+	return 0;
+}
+
+int lpddr2_init(const unsigned int base,
+		const unsigned int ram_address,
+		const struct atmel_mpddrc_config *mpddr_value)
+{
+	struct atmel_mpddr *mpddr = (struct atmel_mpddr *)base;
+	u32 reg;
+
+	writel(mpddr_value->lpddr23_lpr, &mpddr->lpddr23_lpr);
+
+	writel(mpddr_value->tim_cal, &mpddr->tim_cal);
+
+	/* 1. Program the memory device type */
+	writel(mpddr_value->md, &mpddr->md);
+
+	/*
+	 * 2. Program features of the LPDDR2-SDRAM device and timing parameters
+	 */
+	writel(mpddr_value->cr, &mpddr->cr);
+
+	writel(mpddr_value->tpr0, &mpddr->tpr0);
+	writel(mpddr_value->tpr1, &mpddr->tpr1);
+	writel(mpddr_value->tpr2, &mpddr->tpr2);
+
+	/* 3. A NOP command is issued to the LPDDR2-SDRAM */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+	/*
+	 * 3bis. Add memory barrier then Perform a write access to
+	 * any low-power DDR2-SDRAM address to acknowledge the command.
+	*/
+
+	dmb();
+	writel(0, ram_address);
+
+	/* 4. A pause of at least 100 ns must be observed before a single toggle */
+	udelay(1);
+
+	/* 5. A NOP command is issued to the LPDDR2-SDRAM */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+	/*  6. A pause of at least 200 us must be observed before a Reset Command */
+	udelay(200);
+
+	/* 7. A Reset command is issued to the low-power DDR2-SDRAM. */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(63), ram_address);
+
+	/*
+	 * 8. A pause of at least tINIT5 must be observed before issuing
+	 * any commands
+	 */
+	udelay(1);
+
+	/* 9. A Calibration command is issued to the low-power DDR2-SDRAM. */
+	reg = readl(&mpddr->cr);
+	reg &= ~ATMEL_MPDDRC_CR_ZQ_RESET;
+	reg |= ATMEL_MPDDRC_CR_ZQ_RESET;
+	writel(reg, &mpddr->cr);
+
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(10), ram_address);
+
+	/*
+	 * 9bis: The ZQ Calibration command is now issued.
+	 * Program the type of calibration in the MPDDRC_CR: set the
+	 * ZQ field to the SHORT value.
+	 */
+	reg = readl(&mpddr->cr);
+	reg &= ~ATMEL_MPDDRC_CR_ZQ_RESET;
+	reg |= ATMEL_MPDDRC_CR_ZQ_SHORT;
+	writel(reg, &mpddr->cr);
+
+	/*
+	 * 10: A Mode Register Write command with 1 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(1), ram_address);
+
+	/*
+	 * 11: A Mode Register Write command with 2 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(2), ram_address);
+
+	/*
+	 * 12: A Mode Register Write command with 3 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(3), ram_address);
+
+	/*
+	 * 13: A Mode Register Write command with 16 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(16), ram_address);
+
+	/*
+	 * 14: In the DDR Configuration Register, open the input buffers.
+	 */
+#ifdef CONFIG_ATMEL_SFR
+	configure_ddrcfg_input_buffers(true);
+#endif
+
+	/* 15. A NOP command is issued to the LPDDR2-SDRAM */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+	/*
+	 * 16: A Mode Register Write command with 5 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(5), ram_address);
+
+	/*
+	 * 17: A Mode Register Write command with 6 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(6), ram_address);
+
+	/*
+	 * 18: A Mode Register Write command with 8 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(8), ram_address);
+
+	/*
+	 * 19: A Mode Register Write command with 0 to the MRS field
+	 * is issued to the low-power DDR2-SDRAM.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+			 ATMEL_MPDDRC_MR_MRS(0), ram_address);
+
+	/*
+	 * 20: A Normal Mode command is provided.
+	 */
+	atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NORMAL_CMD, ram_address);
+
+	 /* 21: In the DDR Configuration Register, close the input buffers. */
+#ifdef CONFIG_ATMEL_SFR
+	configure_ddrcfg_input_buffers(false);
+#endif
+
+	/*
+	 * 22: Write the refresh rate into the COUNT field in the MPDDRC
+	 * Refresh Timer Register.
+	 */
+	writel(mpddr_value->rtr, &mpddr->rtr);
+
+	/* 23. Configre CAL MR4 register */
+	writel(mpddr_value->cal_mr4, &mpddr->cal_mr4);
+
+	return 0;
+}