diff options
Diffstat (limited to 'roms/u-boot/arch/arm/mach-davinci/da850_lowlevel.c')
| -rw-r--r-- | roms/u-boot/arch/arm/mach-davinci/da850_lowlevel.c | 313 |
1 files changed, 313 insertions, 0 deletions
diff --git a/roms/u-boot/arch/arm/mach-davinci/da850_lowlevel.c b/roms/u-boot/arch/arm/mach-davinci/da850_lowlevel.c new file mode 100644 index 000000000..759c93747 --- /dev/null +++ b/roms/u-boot/arch/arm/mach-davinci/da850_lowlevel.c @@ -0,0 +1,313 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * SoC-specific lowlevel code for DA850 + * + * Copyright (C) 2011 + * Heiko Schocher, DENX Software Engineering, hs@denx.de. + */ +#include <common.h> +#include <init.h> +#include <nand.h> +#include <ns16550.h> +#include <post.h> +#include <asm/arch/da850_lowlevel.h> +#include <asm/arch/hardware.h> +#include <asm/arch/davinci_misc.h> +#include <asm/arch/ddr2_defs.h> +#include <asm/ti-common/davinci_nand.h> +#include <asm/arch/pll_defs.h> + +void davinci_enable_uart0(void) +{ + lpsc_on(DAVINCI_LPSC_UART0); + + /* Bringup UART0 out of reset */ + REG(UART0_PWREMU_MGMT) = 0x00006001; +} + +#if defined(CONFIG_SYS_DA850_PLL_INIT) +static void da850_waitloop(unsigned long loopcnt) +{ + unsigned long i; + + for (i = 0; i < loopcnt; i++) + asm(" NOP"); +} + +static int da850_pll_init(struct davinci_pllc_regs *reg, unsigned long pllmult) +{ + if (reg == davinci_pllc0_regs) + /* Unlock PLL registers. */ + clrbits_le32(&davinci_syscfg_regs->cfgchip0, PLL_MASTER_LOCK); + + /* + * Set PLLENSRC '0',bit 5, PLL Enable(PLLEN) selection is controlled + * through MMR + */ + clrbits_le32(®->pllctl, PLLCTL_PLLENSRC); + /* PLLCTL.EXTCLKSRC bit 9 should be left at 0 for Freon */ + clrbits_le32(®->pllctl, PLLCTL_EXTCLKSRC); + + /* Set PLLEN=0 => PLL BYPASS MODE */ + clrbits_le32(®->pllctl, PLLCTL_PLLEN); + + da850_waitloop(150); + + if (reg == davinci_pllc0_regs) { + /* + * Select the Clock Mode bit 8 as External Clock or On Chip + * Oscilator + */ + dv_maskbits(®->pllctl, ~PLLCTL_RES_9); + setbits_le32(®->pllctl, + (CONFIG_SYS_DV_CLKMODE << PLLCTL_CLOCK_MODE_SHIFT)); + } + + /* Clear PLLRST bit to reset the PLL */ + clrbits_le32(®->pllctl, PLLCTL_PLLRST); + + /* Disable the PLL output */ + setbits_le32(®->pllctl, PLLCTL_PLLDIS); + + /* PLL initialization sequence */ + /* + * Power up the PLL- PWRDN bit set to 0 to bring the PLL out of + * power down bit + */ + clrbits_le32(®->pllctl, PLLCTL_PLLPWRDN); + + /* Enable the PLL from Disable Mode PLLDIS bit to 0 */ + clrbits_le32(®->pllctl, PLLCTL_PLLDIS); + +#if defined(CONFIG_SYS_DA850_PLL0_PREDIV) + /* program the prediv */ + if (reg == davinci_pllc0_regs && CONFIG_SYS_DA850_PLL0_PREDIV) + writel((PLL_DIVEN | CONFIG_SYS_DA850_PLL0_PREDIV), + ®->prediv); +#endif + + /* Program the required multiplier value in PLLM */ + writel(pllmult, ®->pllm); + + /* program the postdiv */ + if (reg == davinci_pllc0_regs) + writel((PLL_POSTDEN | CONFIG_SYS_DA850_PLL0_POSTDIV), + ®->postdiv); + else + writel((PLL_POSTDEN | CONFIG_SYS_DA850_PLL1_POSTDIV), + ®->postdiv); + + /* + * Check for the GOSTAT bit in PLLSTAT to clear to 0 to indicate that + * no GO operation is currently in progress + */ + while ((readl(®->pllstat) & PLLCMD_GOSTAT) == PLLCMD_GOSTAT) + ; + + if (reg == davinci_pllc0_regs) { + writel(CONFIG_SYS_DA850_PLL0_PLLDIV1, ®->plldiv1); + writel(CONFIG_SYS_DA850_PLL0_PLLDIV2, ®->plldiv2); + writel(CONFIG_SYS_DA850_PLL0_PLLDIV3, ®->plldiv3); + writel(CONFIG_SYS_DA850_PLL0_PLLDIV4, ®->plldiv4); + writel(CONFIG_SYS_DA850_PLL0_PLLDIV5, ®->plldiv5); + writel(CONFIG_SYS_DA850_PLL0_PLLDIV6, ®->plldiv6); + writel(CONFIG_SYS_DA850_PLL0_PLLDIV7, ®->plldiv7); + } else { + writel(CONFIG_SYS_DA850_PLL1_PLLDIV1, ®->plldiv1); + writel(CONFIG_SYS_DA850_PLL1_PLLDIV2, ®->plldiv2); + writel(CONFIG_SYS_DA850_PLL1_PLLDIV3, ®->plldiv3); + } + + /* + * Set the GOSET bit in PLLCMD to 1 to initiate a new divider + * transition. + */ + setbits_le32(®->pllcmd, PLLCMD_GOSTAT); + + /* + * Wait for the GOSTAT bit in PLLSTAT to clear to 0 + * (completion of phase alignment). + */ + while ((readl(®->pllstat) & PLLCMD_GOSTAT) == PLLCMD_GOSTAT) + ; + + /* Wait for PLL to reset properly. See PLL spec for PLL reset time */ + da850_waitloop(200); + + /* Set the PLLRST bit in PLLCTL to 1 to bring the PLL out of reset */ + setbits_le32(®->pllctl, PLLCTL_PLLRST); + + /* Wait for PLL to lock. See PLL spec for PLL lock time */ + da850_waitloop(2400); + + /* + * Set the PLLEN bit in PLLCTL to 1 to remove the PLL from bypass + * mode + */ + setbits_le32(®->pllctl, PLLCTL_PLLEN); + + + /* + * clear EMIFA and EMIFB clock source settings, let them + * run off SYSCLK + */ + if (reg == davinci_pllc0_regs) + dv_maskbits(&davinci_syscfg_regs->cfgchip3, + ~(PLL_SCSCFG3_DIV45PENA | PLL_SCSCFG3_EMA_CLKSRC)); + + return 0; +} +#endif /* CONFIG_SYS_DA850_PLL_INIT */ + +#if defined(CONFIG_SYS_DA850_DDR_INIT) +static int da850_ddr_setup(void) +{ + unsigned long tmp; + + /* Enable the Clock to DDR2/mDDR */ + lpsc_on(DAVINCI_LPSC_DDR_EMIF); + + tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); + if ((tmp & VTP_POWERDWN) == VTP_POWERDWN) { + /* Begin VTP Calibration */ + clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_POWERDWN); + clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_LOCK); + setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); + clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); + setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); + + /* Polling READY bit to see when VTP calibration is done */ + tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); + while ((tmp & VTP_READY) != VTP_READY) + tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); + + setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_LOCK); + setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_POWERDWN); + } + setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_IOPWRDWN); + writel(CONFIG_SYS_DA850_DDR2_DDRPHYCR, &dv_ddr2_regs_ctrl->ddrphycr); + + if (CONFIG_SYS_DA850_DDR2_SDBCR & (1 << DV_DDR_SDCR_DDR2EN_SHIFT)) { + /* DDR2 */ + clrbits_le32(&davinci_syscfg1_regs->ddr_slew, + (1 << DDR_SLEW_DDR_PDENA_BIT) | + (1 << DDR_SLEW_CMOSEN_BIT)); + } else { + /* MOBILE DDR */ + setbits_le32(&davinci_syscfg1_regs->ddr_slew, + (1 << DDR_SLEW_DDR_PDENA_BIT) | + (1 << DDR_SLEW_CMOSEN_BIT)); + } + + /* + * SDRAM Configuration Register (SDCR): + * First set the BOOTUNLOCK bit to make configuration bits + * writeable. + */ + setbits_le32(&dv_ddr2_regs_ctrl->sdbcr, DV_DDR_BOOTUNLOCK); + + /* + * Write the new value of these bits and clear BOOTUNLOCK. + * At the same time, set the TIMUNLOCK bit to allow changing + * the timing registers + */ + tmp = CONFIG_SYS_DA850_DDR2_SDBCR; + tmp &= ~DV_DDR_BOOTUNLOCK; + tmp |= DV_DDR_TIMUNLOCK; + writel(tmp, &dv_ddr2_regs_ctrl->sdbcr); + + /* write memory configuration and timing */ + if (!(CONFIG_SYS_DA850_DDR2_SDBCR & (1 << DV_DDR_SDCR_DDR2EN_SHIFT))) { + /* MOBILE DDR only*/ + writel(CONFIG_SYS_DA850_DDR2_SDBCR2, + &dv_ddr2_regs_ctrl->sdbcr2); + } + writel(CONFIG_SYS_DA850_DDR2_SDTIMR, &dv_ddr2_regs_ctrl->sdtimr); + writel(CONFIG_SYS_DA850_DDR2_SDTIMR2, &dv_ddr2_regs_ctrl->sdtimr2); + + /* clear the TIMUNLOCK bit and write the value of the CL field */ + tmp &= ~DV_DDR_TIMUNLOCK; + writel(tmp, &dv_ddr2_regs_ctrl->sdbcr); + + /* + * LPMODEN and MCLKSTOPEN must be set! + * Without this bits set, PSC don;t switch states !! + */ + writel(CONFIG_SYS_DA850_DDR2_SDRCR | + (1 << DV_DDR_SRCR_LPMODEN_SHIFT) | + (1 << DV_DDR_SRCR_MCLKSTOPEN_SHIFT), + &dv_ddr2_regs_ctrl->sdrcr); + + /* SyncReset the Clock to EMIF3A SDRAM */ + lpsc_syncreset(DAVINCI_LPSC_DDR_EMIF); + /* Enable the Clock to EMIF3A SDRAM */ + lpsc_on(DAVINCI_LPSC_DDR_EMIF); + + /* disable self refresh */ + clrbits_le32(&dv_ddr2_regs_ctrl->sdrcr, + DV_DDR_SDRCR_LPMODEN | DV_DDR_SDRCR_MCLKSTOPEN); + writel(CONFIG_SYS_DA850_DDR2_PBBPR, &dv_ddr2_regs_ctrl->pbbpr); + + return 0; +} +#endif /* CONFIG_SYS_DA850_DDR_INIT */ + +__attribute__((weak)) +void board_gpio_init(void) +{ + return; +} + +int arch_cpu_init(void) +{ + /* Unlock kick registers */ + writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); + writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); + + dv_maskbits(&davinci_syscfg_regs->suspsrc, + CONFIG_SYS_DA850_SYSCFG_SUSPSRC); + + /* configure pinmux settings */ + if (davinci_configure_pin_mux_items(pinmuxes, pinmuxes_size)) + return 1; + +#if defined(CONFIG_SYS_DA850_PLL_INIT) + /* PLL setup */ + da850_pll_init(davinci_pllc0_regs, CONFIG_SYS_DA850_PLL0_PLLM); + da850_pll_init(davinci_pllc1_regs, CONFIG_SYS_DA850_PLL1_PLLM); +#endif + /* setup CSn config */ +#if defined(CONFIG_SYS_DA850_CS2CFG) + writel(CONFIG_SYS_DA850_CS2CFG, &davinci_emif_regs->ab1cr); +#endif +#if defined(CONFIG_SYS_DA850_CS3CFG) + writel(CONFIG_SYS_DA850_CS3CFG, &davinci_emif_regs->ab2cr); +#endif + + da8xx_configure_lpsc_items(lpsc, lpsc_size); + + /* GPIO setup */ + board_gpio_init(); + +#if !CONFIG_IS_ENABLED(DM_SERIAL) + ns16550_init((struct ns16550 *)(CONFIG_SYS_NS16550_COM1), + CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); +#endif + /* + * Fix Power and Emulation Management Register + * see sprufw3a.pdf page 37 Table 24 + */ + writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | + DAVINCI_UART_PWREMU_MGMT_UTRST), +#if (CONFIG_SYS_NS16550_COM1 == DAVINCI_UART0_BASE) + &davinci_uart0_ctrl_regs->pwremu_mgmt); +#else + &davinci_uart2_ctrl_regs->pwremu_mgmt); +#endif + +#if defined(CONFIG_SYS_DA850_DDR_INIT) + da850_ddr_setup(); +#endif + + return 0; +} |