1 files changed, 111 insertions, 0 deletions
diff --git a/roms/u-boot/arch/arm/mach-kirkwood/include/mach/config.h b/roms/u-boot/arch/arm/mach-kirkwood/include/mach/config.h
new file mode 100644
index 000000000..f5538f4a9
--- /dev/null
+++ b/roms/u-boot/arch/arm/mach-kirkwood/include/mach/config.h
@@ -0,0 +1,111 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Kirkwood platform
+ */
+
+#ifndef _KW_CONFIG_H
+#define _KW_CONFIG_H
+
+#if defined (CONFIG_KW88F6281)
+#include <asm/arch/kw88f6281.h>
+#elif defined (CONFIG_KW88F6192)
+#include <asm/arch/kw88f6192.h>
+#else
+#error "SOC Name not defined"
+#endif /* CONFIG_KW88F6281 */
+
+#include <asm/arch/soc.h>
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
+
+/*
+ * By default kwbimage.cfg from board specific folder is used
+ * If for some board, different configuration file need to be used,
+ * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
+ */
+#ifndef CONFIG_SYS_KWD_CONFIG
+#define	CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
+#endif /* CONFIG_SYS_KWD_CONFIG */
+
+/* Kirkwood has 2k of Security SRAM, use it for SP */
+#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
+
+#define CONFIG_I2C_MVTWSI_BASE0	KW_TWSI_BASE
+#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
+#define MV_SATA_BASE		KW_SATA_BASE
+#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
+#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL		1
+#endif
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
+#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_EHCI_IS_TDI
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * IDE Support on SATA ports
+ */
+#ifdef CONFIG_IDE
+#define __io
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS		2
+#define CONFIG_SYS_IDE_MAXDEVICE	2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
+#endif /* CONFIG_IDE */
+
+/*
+ * I2C related stuff
+ */
+#if defined(CONFIG_CMD_I2C) && !CONFIG_IS_ENABLED(DM_I2C)
+#ifndef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MVTWSI
+#endif
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
+/* Use common timer */
+#define CONFIG_SYS_TIMER_COUNTS_DOWN
+#define CONFIG_SYS_TIMER_COUNTER	(MVEBU_TIMER_BASE + 0x14)
+#define CONFIG_SYS_TIMER_RATE		CONFIG_SYS_TCLK
+
+#endif /* _KW_CONFIG_H */