diff options
Diffstat (limited to 'roms/u-boot/arch/mips/mach-mtmips/mt7628')
| -rw-r--r-- | roms/u-boot/arch/mips/mach-mtmips/mt7628/Kconfig | 53 | ||||
| -rw-r--r-- | roms/u-boot/arch/mips/mach-mtmips/mt7628/Makefile | 6 | ||||
| -rw-r--r-- | roms/u-boot/arch/mips/mach-mtmips/mt7628/ddr.c | 175 | ||||
| -rw-r--r-- | roms/u-boot/arch/mips/mach-mtmips/mt7628/init.c | 113 | ||||
| -rw-r--r-- | roms/u-boot/arch/mips/mach-mtmips/mt7628/lowlevel_init.S | 161 | ||||
| -rw-r--r-- | roms/u-boot/arch/mips/mach-mtmips/mt7628/mt7628.h | 104 | ||||
| -rw-r--r-- | roms/u-boot/arch/mips/mach-mtmips/mt7628/serial.c | 34 |
7 files changed, 646 insertions, 0 deletions
diff --git a/roms/u-boot/arch/mips/mach-mtmips/mt7628/Kconfig b/roms/u-boot/arch/mips/mach-mtmips/mt7628/Kconfig new file mode 100644 index 000000000..e3f56e782 --- /dev/null +++ b/roms/u-boot/arch/mips/mach-mtmips/mt7628/Kconfig @@ -0,0 +1,53 @@ + +if SOC_MT7628 + +choice + prompt "Board select" + +config BOARD_GARDENA_SMART_GATEWAY_MT7688 + bool "GARDENA smart Gateway" + select BOARD_LATE_INIT + help + GARDENA smart Gateway boards have a MT7688 SoC with 128 MiB of RAM + and 8 MiB of flash (SPI NOR) and additional SPI NAND storage. + +config BOARD_LINKIT_SMART_7688 + bool "LinkIt Smart 7688" + help + Seeed LinkIt Smart 7688 boards have a MT7688 SoC with 128 MiB of RAM + and 32 MiB of flash (SPI). + Between its different peripherals there's an integrated switch with 4 + ethernet ports, 1 USB port, 1 UART, GPIO buttons and LEDs, and + a MT7688 (PCIe). + +config BOARD_MT7628_RFB + bool "MediaTek MT7628 RFB" + help + The reference design of MT7628. The board has 128 MiB DDR2, 8 MiB + SPI-NOR flash, 1 built-in switch with 5 ports, 1 UART, 1 USB host, + 1 SDXC, 1 PCIe socket and JTAG pins. + +config BOARD_VOCORE2 + bool "VoCore2" + select SPL_SERIAL_SUPPORT + select SPL_UART2_SPIS_PINMUX + help + VoCore VoCore2 board has a MT7628 SoC with 128 MiB of RAM + and 16 MiB of flash (SPI). + +endchoice + +config SPL_UART2_SPIS_PINMUX + bool "Use alternative pinmux for UART2 in SPL stage" + depends on SPL_SERIAL_SUPPORT + default n + help + Select this if the UART2 of your board is connected to GPIO 16/17 + (shared with SPIS) rather than the usual GPIO 20/21. + +source "board/gardena/smart-gateway-mt7688/Kconfig" +source "board/mediatek/mt7628/Kconfig" +source "board/seeed/linkit-smart-7688/Kconfig" +source "board/vocore/vocore2/Kconfig" + +endif diff --git a/roms/u-boot/arch/mips/mach-mtmips/mt7628/Makefile b/roms/u-boot/arch/mips/mach-mtmips/mt7628/Makefile new file mode 100644 index 000000000..7e139d5ad --- /dev/null +++ b/roms/u-boot/arch/mips/mach-mtmips/mt7628/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0 + +obj-y += lowlevel_init.o +obj-y += init.o +obj-y += ddr.o +obj-$(CONFIG_SPL_BUILD) += serial.o diff --git a/roms/u-boot/arch/mips/mach-mtmips/mt7628/ddr.c b/roms/u-boot/arch/mips/mach-mtmips/mt7628/ddr.c new file mode 100644 index 000000000..4e7245990 --- /dev/null +++ b/roms/u-boot/arch/mips/mach-mtmips/mt7628/ddr.c @@ -0,0 +1,175 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Weijie Gao <weijie.gao@mediatek.com> + */ + +#include <common.h> +#include <asm/addrspace.h> +#include <asm/global_data.h> +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/sizes.h> +#include <linux/io.h> +#include <mach/ddr.h> +#include <mach/mc.h> +#include "mt7628.h" + +DECLARE_GLOBAL_DATA_PTR; + +/* DDR2 DQ_DLY */ +#define DDR2_DQ_DLY \ + ((0x8 << DQ1_DELAY_COARSE_TUNING_S) | \ + (0x2 << DQ1_DELAY_FINE_TUNING_S) | \ + (0x8 << DQ0_DELAY_COARSE_TUNING_S) | \ + (0x2 << DQ0_DELAY_FINE_TUNING_S)) + +/* DDR2 DQS_DLY */ +#define DDR2_DQS_DLY \ + ((0x8 << DQS1_DELAY_COARSE_TUNING_S) | \ + (0x3 << DQS1_DELAY_FINE_TUNING_S) | \ + (0x8 << DQS0_DELAY_COARSE_TUNING_S) | \ + (0x3 << DQS0_DELAY_FINE_TUNING_S)) + +const struct mc_ddr_cfg ddr1_cfgs_200mhz[] = { + [DRAM_8MB] = { 0x34A1EB94, 0x20262324, 0x28000033, 0x00000002, 0x00000000 }, + [DRAM_16MB] = { 0x34A1EB94, 0x202A2324, 0x28000033, 0x00000002, 0x00000000 }, + [DRAM_32MB] = { 0x34A1E5CA, 0x202E2324, 0x28000033, 0x00000002, 0x00000000 }, + [DRAM_64MB] = { 0x3421E5CA, 0x20322324, 0x28000033, 0x00000002, 0x00000000 }, + [DRAM_128MB] = { 0x241B05CA, 0x20362334, 0x28000033, 0x00000002, 0x00000000 }, +}; + +const struct mc_ddr_cfg ddr1_cfgs_160mhz[] = { + [DRAM_8MB] = { 0x239964A1, 0x20262323, 0x00000033, 0x00000002, 0x00000000 }, + [DRAM_16MB] = { 0x239964A1, 0x202A2323, 0x00000033, 0x00000002, 0x00000000 }, + [DRAM_32MB] = { 0x239964A1, 0x202E2323, 0x00000033, 0x00000002, 0x00000000 }, + [DRAM_64MB] = { 0x239984A1, 0x20322323, 0x00000033, 0x00000002, 0x00000000 }, + [DRAM_128MB] = { 0x239AB4A1, 0x20362333, 0x00000033, 0x00000002, 0x00000000 }, +}; + +const struct mc_ddr_cfg ddr2_cfgs_200mhz[] = { + [DRAM_32MB] = { 0x2519E2E5, 0x222E2323, 0x68000C43, 0x00000452, 0x0000000A }, + [DRAM_64MB] = { 0x249AA2E5, 0x22322323, 0x68000C43, 0x00000452, 0x0000000A }, + [DRAM_128MB] = { 0x249B42E5, 0x22362323, 0x68000C43, 0x00000452, 0x0000000A }, + [DRAM_256MB] = { 0x249CE2E5, 0x223A2323, 0x68000C43, 0x00000452, 0x0000000A }, +}; + +const struct mc_ddr_cfg ddr2_cfgs_160mhz[] = { + [DRAM_32MB] = { 0x23918250, 0x222E2322, 0x40000A43, 0x00000452, 0x00000006 }, + [DRAM_64MB] = { 0x239A2250, 0x22322322, 0x40000A43, 0x00000452, 0x00000008 }, + [DRAM_128MB] = { 0x2392A250, 0x22362322, 0x40000A43, 0x00000452, 0x00000008 }, + [DRAM_256MB] = { 0x24140250, 0x223A2322, 0x40000A43, 0x00000452, 0x00000008 }, +}; + +static void mt7628_memc_reset(int assert) +{ + void __iomem *sysc = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE); + + if (assert) + setbits_32(sysc + SYSCTL_RSTCTL_REG, MC_RST); + else + clrbits_32(sysc + SYSCTL_RSTCTL_REG, MC_RST); +} + +static void mt7628_ddr_pad_ldo_config(int ddr_type, int pkg_type) +{ + void __iomem *rgc = ioremap_nocache(RGCTL_BASE, RGCTL_SIZE); + u32 ck_pad1, cmd_pad1, dq_pad0, dq_pad1, dqs_pad0, dqs_pad1; + + setbits_32(rgc + RGCTL_PMU_G0_REG, PMU_CFG_EN); + + if (ddr_type == DRAM_DDR1) + setbits_32(rgc + RGCTL_PMU_G3_REG, RG_DDRLDO_VOSEL); + else + clrbits_32(rgc + RGCTL_PMU_G3_REG, RG_DDRLDO_VOSEL); + + setbits_32(rgc + RGCTL_PMU_G3_REG, NI_DDRLDO_EN); + + __udelay(250 * 50); + + setbits_32(rgc + RGCTL_PMU_G3_REG, NI_DDRLDO_STB); + setbits_32(rgc + RGCTL_PMU_G1_REG, RG_BUCK_FPWM); + + ck_pad1 = readl(rgc + RGCTL_DDR_PAD_CK_G1_REG); + cmd_pad1 = readl(rgc + RGCTL_DDR_PAD_CMD_G1_REG); + dq_pad0 = readl(rgc + RGCTL_DDR_PAD_DQ_G0_REG); + dq_pad1 = readl(rgc + RGCTL_DDR_PAD_DQ_G1_REG); + dqs_pad0 = readl(rgc + RGCTL_DDR_PAD_DQS_G0_REG); + dqs_pad1 = readl(rgc + RGCTL_DDR_PAD_DQS_G1_REG); + + ck_pad1 &= ~(DRVP_M | DRVN_M); + cmd_pad1 &= ~(DRVP_M | DRVN_M); + dq_pad0 &= ~RTT_M; + dq_pad1 &= ~(DRVP_M | DRVN_M); + dqs_pad0 &= ~RTT_M; + dqs_pad1 &= ~(DRVP_M | DRVN_M); + + if (pkg_type == PKG_ID_KN) { + ck_pad1 |= (3 << DRVP_S) | (3 << DRVN_S); + cmd_pad1 |= (3 << DRVP_S) | (3 << DRVN_S); + dq_pad1 |= (3 << DRVP_S) | (3 << DRVN_S); + dqs_pad1 |= (3 << DRVP_S) | (3 << DRVN_S); + } else { + ck_pad1 |= (12 << DRVP_S) | (12 << DRVN_S); + cmd_pad1 |= (2 << DRVP_S) | (2 << DRVN_S); + dqs_pad1 |= (12 << DRVP_S) | (12 << DRVN_S); + if (ddr_type == DRAM_DDR1) + dq_pad1 |= (7 << DRVP_S) | (7 << DRVN_S); + else + dq_pad1 |= (4 << DRVP_S) | (4 << DRVN_S); + } + + writel(ck_pad1, rgc + RGCTL_DDR_PAD_CK_G1_REG); + writel(cmd_pad1, rgc + RGCTL_DDR_PAD_CMD_G1_REG); + writel(dq_pad0, rgc + RGCTL_DDR_PAD_DQ_G0_REG); + writel(dq_pad1, rgc + RGCTL_DDR_PAD_DQ_G1_REG); + writel(dqs_pad0, rgc + RGCTL_DDR_PAD_DQS_G0_REG); + writel(dqs_pad1, rgc + RGCTL_DDR_PAD_DQS_G1_REG); +} + +void mt7628_ddr_init(void) +{ + void __iomem *sysc; + int ddr_type, pkg_type, lspd; + struct mc_ddr_init_param param; + + sysc = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE); + ddr_type = readl(sysc + SYSCTL_SYSCFG0_REG) & DRAM_TYPE; + pkg_type = !!(readl(sysc + SYSCTL_CHIP_REV_ID_REG) & PKG_ID); + lspd = readl(sysc + SYSCTL_CLKCFG0_REG) & + (CPU_PLL_FROM_BBP | CPU_PLL_FROM_XTAL); + + if (pkg_type == PKG_ID_KN) + ddr_type = DRAM_DDR1; + + mt7628_memc_reset(1); + __udelay(200); + + mt7628_ddr_pad_ldo_config(ddr_type, pkg_type); + + param.memc = ioremap_nocache(MEMCTL_BASE, MEMCTL_SIZE); + param.dq_dly = DDR2_DQ_DLY; + param.dqs_dly = DDR2_DQS_DLY; + param.mc_reset = mt7628_memc_reset; + param.memsize = 0; + param.bus_width = 0; + + if (ddr_type == DRAM_DDR1) { + if (lspd) + param.cfgs = ddr1_cfgs_160mhz; + else + param.cfgs = ddr1_cfgs_200mhz; + ddr1_init(¶m); + } else { + if (lspd) + param.cfgs = ddr2_cfgs_160mhz; + else + param.cfgs = ddr2_cfgs_200mhz; + ddr2_init(¶m); + } + + ddr_calibrate(param.memc, param.memsize, param.bus_width); + + gd->ram_size = param.memsize; +} diff --git a/roms/u-boot/arch/mips/mach-mtmips/mt7628/init.c b/roms/u-boot/arch/mips/mach-mtmips/mt7628/init.c new file mode 100644 index 000000000..6b535129d --- /dev/null +++ b/roms/u-boot/arch/mips/mach-mtmips/mt7628/init.c @@ -0,0 +1,113 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Weijie Gao <weijie.gao@mediatek.com> + */ + +#include <common.h> +#include <clk.h> +#include <dm.h> +#include <asm/global_data.h> +#include <dm/uclass.h> +#include <dt-bindings/clock/mt7628-clk.h> +#include <linux/io.h> +#include "mt7628.h" + +DECLARE_GLOBAL_DATA_PTR; + +static void set_init_timer_freq(void) +{ + void __iomem *sysc; + u32 bs, val, timer_freq_post; + + sysc = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE); + + /* We can't use the clk driver as the DM has not been initialized yet */ + bs = readl(sysc + SYSCTL_SYSCFG0_REG); + if ((bs & XTAL_FREQ_SEL) == XTAL_25MHZ) { + gd->arch.timer_freq = 25000000; + timer_freq_post = 575000000; + } else { + gd->arch.timer_freq = 40000000; + timer_freq_post = 580000000; + } + + val = readl(sysc + SYSCTL_CLKCFG0_REG); + if (!(val & (CPU_PLL_FROM_BBP | CPU_PLL_FROM_XTAL))) + gd->arch.timer_freq = timer_freq_post; +} + +void mt7628_init(void) +{ + set_init_timer_freq(); + + mt7628_ddr_init(); +} + +int print_cpuinfo(void) +{ + void __iomem *sysc; + struct udevice *clkdev; + u32 val, ver, eco, pkg, ddr, chipmode, ee; + ulong cpu_clk, bus_clk, xtal_clk, timer_freq; + struct clk clk; + int ret; + + sysc = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE); + + val = readl(sysc + SYSCTL_CHIP_REV_ID_REG); + ver = (val & VER_M) >> VER_S; + eco = (val & ECO_M) >> ECO_S; + pkg = !!(val & PKG_ID); + + val = readl(sysc + SYSCTL_SYSCFG0_REG); + ddr = val & DRAM_TYPE; + chipmode = (val & CHIP_MODE_M) >> CHIP_MODE_S; + + val = readl(sysc + SYSCTL_EFUSE_CFG_REG); + ee = val & EFUSE_MT7688; + + if (pkg == PKG_ID_KN) + ddr = DRAM_DDR1; + + printf("CPU: MediaTek MT%u%c ver:%u eco:%u\n", + ee ? 7688 : 7628, pkg ? 'A' : 'K', ver, eco); + + printf("Boot: DDR%s, SPI-NOR %u-Byte Addr, CPU clock from %s\n", + ddr ? "" : "2", chipmode & 0x01 ? 4 : 3, + chipmode & 0x02 ? "XTAL" : "CPLL"); + + ret = uclass_get_device_by_driver(UCLASS_CLK, DM_DRIVER_GET(mt7628_clk), + &clkdev); + if (ret) + return ret; + + clk.dev = clkdev; + + clk.id = CLK_CPU; + cpu_clk = clk_get_rate(&clk); + + clk.id = CLK_SYS; + bus_clk = clk_get_rate(&clk); + + clk.id = CLK_XTAL; + xtal_clk = clk_get_rate(&clk); + + clk.id = CLK_MIPS_CNT; + timer_freq = clk_get_rate(&clk); + + /* Set final timer frequency */ + if (timer_freq) + gd->arch.timer_freq = timer_freq; + + printf("Clock: CPU: %luMHz, Bus: %luMHz, XTAL: %luMHz\n", + cpu_clk / 1000000, bus_clk / 1000000, xtal_clk / 1000000); + + return 0; +} + +ulong notrace get_tbclk(void) +{ + return gd->arch.timer_freq; +} diff --git a/roms/u-boot/arch/mips/mach-mtmips/mt7628/lowlevel_init.S b/roms/u-boot/arch/mips/mach-mtmips/mt7628/lowlevel_init.S new file mode 100644 index 000000000..e4a6c0358 --- /dev/null +++ b/roms/u-boot/arch/mips/mach-mtmips/mt7628/lowlevel_init.S @@ -0,0 +1,161 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Weijie Gao <weijie.gao@mediatek.com> + */ + +#include <config.h> +#include <asm-offsets.h> +#include <asm/cacheops.h> +#include <asm/regdef.h> +#include <asm/mipsregs.h> +#include <asm/addrspace.h> +#include <asm/asm.h> +#include "mt7628.h" + +/* Set temporary stack address range */ +#ifndef CONFIG_SYS_INIT_SP_ADDR +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \ + CONFIG_SYS_INIT_SP_OFFSET) +#endif + +#define CACHE_STACK_SIZE 0x4000 +#define CACHE_STACK_BASE (CONFIG_SYS_INIT_SP_ADDR - CACHE_STACK_SIZE) + +#define DELAY_USEC(us) ((58 * (us)) / 3) + + .set noreorder + +LEAF(mips_sram_init) +#ifndef CONFIG_SKIP_LOWLEVEL_INIT + /* Setup CPU PLL */ + li t0, DELAY_USEC(1000000) + li t1, KSEG1ADDR(SYSCTL_BASE + SYSCTL_ROM_STATUS_REG) + li t2, KSEG1ADDR(SYSCTL_BASE + SYSCTL_CLKCFG0_REG) + +_check_rom_status: + lw t3, 0(t1) + andi t3, t3, 1 + bnez t3, _rom_normal + subu t0, t0, 1 + bnez t0, _check_rom_status + nop + + lw t3, 0(t2) + ori t3, (CPU_PLL_FROM_BBP | CPU_PLL_FROM_XTAL) + xori t3, CPU_PLL_FROM_BBP + b _cpu_pll_done + nop + +_rom_normal: + lw t3, 0(t2) + ori t3, (CPU_PLL_FROM_BBP | CPU_PLL_FROM_XTAL | \ + DIS_BBP_SLEEP | EN_BBP_CLK) + xori t3, (CPU_PLL_FROM_BBP | CPU_PLL_FROM_XTAL) + +_cpu_pll_done: + sw t3, 0(t2) + + li t2, KSEG1ADDR(RBUSCTL_BASE + RBUSCTL_DYN_CFG0_REG) + lw t3, 0(t2) + ori t3, t3, (CPU_FDIV_M | CPU_FFRAC_M) + xori t3, t3, (CPU_FDIV_M | CPU_FFRAC_M) + ori t3, t3, ((1 << CPU_FDIV_S) | (1 << CPU_FFRAC_S)) + sw t3, 0(t2) + + /* Clear WST & SPR bits in ErrCtl */ + mfc0 t0, CP0_ECC + ins t0, zero, 30, 2 + mtc0 t0, CP0_ECC + ehb + + /* Simply initialize I-Cache */ + li a0, 0 + li a1, CONFIG_SYS_ICACHE_SIZE + + mtc0 zero, CP0_TAGLO /* Zero to DDataLo */ + +1: cache INDEX_STORE_TAG_I, 0(a0) + addiu a0, CONFIG_SYS_ICACHE_LINE_SIZE + bne a0, a1, 1b + nop + + /* Simply initialize D-Cache */ + li a0, 0 + li a1, CONFIG_SYS_DCACHE_SIZE + + mtc0 zero, CP0_TAGLO, 2 + +2: cache INDEX_STORE_TAG_D, 0(a0) + addiu a0, CONFIG_SYS_DCACHE_LINE_SIZE + bne a0, a1, 2b + nop + + /* Set KSEG0 Cachable */ + mfc0 t0, CP0_CONFIG + and t0, t0, MIPS_CONF_IMPL + or t0, t0, CONF_CM_CACHABLE_NONCOHERENT + mtc0 t0, CP0_CONFIG + ehb + + /* Lock D-Cache */ + PTR_LI a0, CACHE_STACK_BASE /* D-Cache lock base */ + li a1, CACHE_STACK_SIZE /* D-Cache lock size */ + li a2, 0x1ffff800 /* Mask of DTagLo[PTagLo] */ + +3: + /* Lock one cacheline */ + and t0, a0, a2 + ori t0, 0xe0 /* Valid & Dirty & Lock bits */ + mtc0 t0, CP0_TAGLO, 2 /* Write to DTagLo */ + ehb + cache INDEX_STORE_TAG_D, 0(a0) + + addiu a0, CONFIG_SYS_DCACHE_LINE_SIZE + sub a1, CONFIG_SYS_DCACHE_LINE_SIZE + bnez a1, 3b + nop +#endif /* CONFIG_SKIP_LOWLEVEL_INIT */ + + jr ra + nop + END(mips_sram_init) + +NESTED(lowlevel_init, 0, ra) + /* Save ra and do real lowlevel initialization */ + move s0, ra + + PTR_LA t9, mt7628_init + jalr t9 + nop + + move ra, s0 + +#if CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F) + /* Set malloc base */ + li t0, (CONFIG_SYS_INIT_SP_ADDR + 15) & (~15) + PTR_S t0, GD_MALLOC_BASE(k0) # gd->malloc_base offset +#endif + + /* Write back data in locked cache to DRAM */ + PTR_LI a0, CACHE_STACK_BASE /* D-Cache unlock base */ + li a1, CACHE_STACK_SIZE /* D-Cache unlock size */ + +1: + cache HIT_WRITEBACK_INV_D, 0(a0) + addiu a0, CONFIG_SYS_DCACHE_LINE_SIZE + sub a1, CONFIG_SYS_DCACHE_LINE_SIZE + bnez a1, 1b + nop + + /* Set KSEG0 Uncached */ + mfc0 t0, CP0_CONFIG + and t0, t0, MIPS_CONF_IMPL + or t0, t0, CONF_CM_UNCACHED + mtc0 t0, CP0_CONFIG + ehb + + jr ra + nop + END(lowlevel_init) diff --git a/roms/u-boot/arch/mips/mach-mtmips/mt7628/mt7628.h b/roms/u-boot/arch/mips/mach-mtmips/mt7628/mt7628.h new file mode 100644 index 000000000..391880b01 --- /dev/null +++ b/roms/u-boot/arch/mips/mach-mtmips/mt7628/mt7628.h @@ -0,0 +1,104 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Weijie Gao <weijie.gao@mediatek.com> + */ + +#ifndef _MT7628_H_ +#define _MT7628_H_ + +#define SYSCTL_BASE 0x10000000 +#define SYSCTL_SIZE 0x100 +#define MEMCTL_BASE 0x10000300 +#define MEMCTL_SIZE 0x100 +#define RBUSCTL_BASE 0x10000400 +#define RBUSCTL_SIZE 0x100 +#define RGCTL_BASE 0x10001000 +#define RGCTL_SIZE 0x800 + +#define SYSCTL_EFUSE_CFG_REG 0x08 +#define EFUSE_MT7688 0x100000 + +#define SYSCTL_CHIP_REV_ID_REG 0x0c +#define PKG_ID 0x10000 +#define PKG_ID_AN 1 +#define PKG_ID_KN 0 +#define VER_S 8 +#define VER_M 0xf00 +#define ECO_S 0 +#define ECO_M 0x0f + +#define SYSCTL_SYSCFG0_REG 0x10 +#define XTAL_FREQ_SEL 0x40 +#define XTAL_40MHZ 1 +#define XTAL_25MHZ 0 +#define CHIP_MODE_S 1 +#define CHIP_MODE_M 0x0e +#define DRAM_TYPE 0x01 +#define DRAM_DDR1 1 +#define DRAM_DDR2 0 + +#define SYSCTL_ROM_STATUS_REG 0x28 + +#define SYSCTL_CLKCFG0_REG 0x2c +#define DIS_BBP_SLEEP 0x08 +#define EN_BBP_CLK 0x04 +#define CPU_PLL_FROM_BBP 0x02 +#define CPU_PLL_FROM_XTAL 0x01 + +#define SYSCTL_RSTCTL_REG 0x34 +#define MC_RST 0x400 + +#define SYSCTL_AGPIO_CFG_REG 0x3c +#define EPHY_GPIO_AIO_EN_S 17 +#define EPHY_GPIO_AIO_EN_M 0x1e0000 + +#define SYSCTL_GPIO_MODE1_REG 0x60 +#define UART2_MODE_S 26 +#define UART2_MODE_M 0xc000000 +#define UART1_MODE_S 24 +#define UART1_MODE_M 0x3000000 +#define UART0_MODE_S 8 +#define UART0_MODE_M 0x300 +#define SPIS_MODE_S 2 +#define SPIS_MODE_M 0x0c + +#define RBUSCTL_DYN_CFG0_REG 0x40 +#define CPU_FDIV_S 8 +#define CPU_FDIV_M 0xf00 +#define CPU_FFRAC_S 0 +#define CPU_FFRAC_M 0x0f + +#define RGCTL_PMU_G0_REG 0x100 +#define PMU_CFG_EN 0x80000000 + +#define RGCTL_PMU_G1_REG 0x104 +#define RG_BUCK_FPWM 0x02 + +#define RGCTL_PMU_G3_REG 0x10c +#define NI_DDRLDO_STB 0x40000 +#define NI_DDRLDO_EN 0x10000 +#define RG_DDRLDO_VOSEL 0x40 + +#define RGCTL_DDR_PAD_CK_G0_REG 0x700 +#define RGCTL_DDR_PAD_CMD_G0_REG 0x708 +#define RGCTL_DDR_PAD_DQ_G0_REG 0x710 +#define RGCTL_DDR_PAD_DQS_G0_REG 0x718 +#define RTT_S 8 +#define RTT_M 0x700 + +#define RGCTL_DDR_PAD_CK_G1_REG 0x704 +#define RGCTL_DDR_PAD_CMD_G1_REG 0x70c +#define RGCTL_DDR_PAD_DQ_G1_REG 0x714 +#define RGCTL_DDR_PAD_DQS_G1_REG 0x71c +#define DRVP_S 0 +#define DRVP_M 0x0f +#define DRVN_S 8 +#define DRVN_M 0xf00 + +#ifndef __ASSEMBLY__ +void mt7628_ddr_init(void); +#endif + +#endif /* _MT7628_H_ */ diff --git a/roms/u-boot/arch/mips/mach-mtmips/mt7628/serial.c b/roms/u-boot/arch/mips/mach-mtmips/mt7628/serial.c new file mode 100644 index 000000000..a7d324792 --- /dev/null +++ b/roms/u-boot/arch/mips/mach-mtmips/mt7628/serial.c @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 MediaTek Inc. + * + * Author: Weijie Gao <weijie.gao@mediatek.com> + */ + +#include <common.h> +#include <asm/io.h> +#include "mt7628.h" + +void mtmips_spl_serial_init(void) +{ +#ifdef CONFIG_SPL_SERIAL_SUPPORT + void __iomem *base = ioremap_nocache(SYSCTL_BASE, SYSCTL_SIZE); + +#if CONFIG_CONS_INDEX == 1 + clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART0_MODE_M); +#elif CONFIG_CONS_INDEX == 2 + clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART1_MODE_M); +#elif CONFIG_CONS_INDEX == 3 + setbits_32(base + SYSCTL_AGPIO_CFG_REG, EPHY_GPIO_AIO_EN_M); +#ifdef CONFIG_SPL_UART2_SPIS_PINMUX + setbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M); + clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M, + 1 << UART2_MODE_S); +#else + clrbits_32(base + SYSCTL_GPIO_MODE1_REG, UART2_MODE_M); + clrsetbits_32(base + SYSCTL_GPIO_MODE1_REG, SPIS_MODE_M, + 1 << SPIS_MODE_S); +#endif /* CONFIG_SPL_UART2_SPIS_PINMUX */ +#endif /* CONFIG_CONS_INDEX */ +#endif /* CONFIG_SPL_SERIAL_SUPPORT */ +} |