diff options
Diffstat (limited to 'roms/u-boot/arch/powerpc/cpu/mpc85xx/release.S')
| -rw-r--r-- | roms/u-boot/arch/powerpc/cpu/mpc85xx/release.S | 498 |
1 files changed, 498 insertions, 0 deletions
diff --git a/roms/u-boot/arch/powerpc/cpu/mpc85xx/release.S b/roms/u-boot/arch/powerpc/cpu/mpc85xx/release.S new file mode 100644 index 000000000..d37e1ccf1 --- /dev/null +++ b/roms/u-boot/arch/powerpc/cpu/mpc85xx/release.S @@ -0,0 +1,498 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * Kumar Gala <kumar.gala@freescale.com> + */ + +#include <asm-offsets.h> +#include <config.h> +#include <mpc85xx.h> + +#include <ppc_asm.tmpl> +#include <ppc_defs.h> + +#include <asm/cache.h> +#include <asm/mmu.h> + +/* To boot secondary cpus, we need a place for them to start up. + * Normally, they start at 0xfffffffc, but that's usually the + * firmware, and we don't want to have to run the firmware again. + * Instead, the primary cpu will set the BPTR to point here to + * this page. We then set up the core, and head to + * start_secondary. Note that this means that the code below + * must never exceed 1023 instructions (the branch at the end + * would then be the 1024th). + */ + .globl __secondary_start_page + .align 12 +__secondary_start_page: +#ifdef CONFIG_SYS_FSL_ERRATUM_A005125 + msync + isync + mfspr r3, SPRN_HDBCR0 + oris r3, r3, 0x0080 + mtspr SPRN_HDBCR0, r3 +#endif +/* First do some preliminary setup */ + lis r3, HID0_EMCP@h /* enable machine check */ +#ifndef CONFIG_E500MC + ori r3,r3,HID0_TBEN@l /* enable Timebase */ +#endif +#ifdef CONFIG_PHYS_64BIT + ori r3,r3,HID0_ENMAS7@l /* enable MAS7 updates */ +#endif + mtspr SPRN_HID0,r3 + +#ifndef CONFIG_E500MC + li r3,(HID1_ASTME|HID1_ABE)@l /* Addr streaming & broadcast */ + mfspr r0,PVR + andi. r0,r0,0xff + cmpwi r0,0x50@l /* if we are rev 5.0 or greater set MBDD */ + blt 1f + /* Set MBDD bit also */ + ori r3, r3, HID1_MBDD@l +1: + mtspr SPRN_HID1,r3 +#endif + +#ifdef CONFIG_SYS_FSL_ERRATUM_CPU_A003999 + mfspr r3,SPRN_HDBCR1 + oris r3,r3,0x0100 + mtspr SPRN_HDBCR1,r3 +#endif + +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 + mfspr r3,SPRN_SVR + rlwinm r3,r3,0,0xff + li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV + cmpw r3,r4 + beq 1f + +#ifdef CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 + li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 + cmpw r3,r4 + beq 1f +#endif + + /* Not a supported revision affected by erratum */ + b 2f + +1: /* Erratum says set bits 55:60 to 001001 */ + msync + isync + mfspr r3,SPRN_HDBCR0 + li r4,0x48 + rlwimi r3,r4,0,0x1f8 + mtspr SPRN_HDBCR0,r3 + isync +2: +#endif + + /* Enable branch prediction */ + lis r3,BUCSR_ENABLE@h + ori r3,r3,BUCSR_ENABLE@l + mtspr SPRN_BUCSR,r3 + + /* Ensure TB is 0 */ + li r3,0 + mttbl r3 + mttbu r3 + + /* Enable/invalidate the I-Cache */ + lis r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@h + ori r2,r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@l + mtspr SPRN_L1CSR1,r2 +1: + mfspr r3,SPRN_L1CSR1 + and. r1,r3,r2 + bne 1b + + lis r3,(L1CSR1_CPE|L1CSR1_ICE)@h + ori r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l + mtspr SPRN_L1CSR1,r3 + isync +2: + mfspr r3,SPRN_L1CSR1 + andi. r1,r3,L1CSR1_ICE@l + beq 2b + + /* Enable/invalidate the D-Cache */ + lis r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@h + ori r2,r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@l + mtspr SPRN_L1CSR0,r2 +1: + mfspr r3,SPRN_L1CSR0 + and. r1,r3,r2 + bne 1b + + lis r3,(L1CSR0_CPE|L1CSR0_DCE)@h + ori r3,r3,(L1CSR0_CPE|L1CSR0_DCE)@l + mtspr SPRN_L1CSR0,r3 + isync +2: + mfspr r3,SPRN_L1CSR0 + andi. r1,r3,L1CSR0_DCE@l + beq 2b + +#define toreset(x) (x - __secondary_start_page + 0xfffff000) + + /* get our PIR to figure out our table entry */ + lis r3,toreset(__spin_table_addr)@h + ori r3,r3,toreset(__spin_table_addr)@l + lwz r3,0(r3) + + mfspr r0,SPRN_PIR +#ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2 +/* + * PIR definition for Chassis 2 + * 0-17 Reserved (logic 0s) + * 18-19 CHIP_ID, 2'b00 - SoC 1 + * all others - reserved + * 20-24 CLUSTER_ID 5'b00000 - CCM 1 + * all others - reserved + * 25-26 CORE_CLUSTER_ID 2'b00 - cluster 1 + * 2'b01 - cluster 2 + * 2'b10 - cluster 3 + * 2'b11 - cluster 4 + * 27-28 CORE_ID 2'b00 - core 0 + * 2'b01 - core 1 + * 2'b10 - core 2 + * 2'b11 - core 3 + * 29-31 THREAD_ID 3'b000 - thread 0 + * 3'b001 - thread 1 + * + * Power-on PIR increments threads by 0x01, cores within a cluster by 0x08 + * and clusters by 0x20. + * + * We renumber PIR so that all threads in the system are consecutive. + */ + + rlwinm r8,r0,29,0x03 /* r8 = core within cluster */ + srwi r10,r0,5 /* r10 = cluster */ + + mulli r5,r10,CONFIG_SYS_FSL_CORES_PER_CLUSTER + add r5,r5,r8 /* for spin table index */ + mulli r4,r5,CONFIG_SYS_FSL_THREADS_PER_CORE /* for PIR */ +#elif defined(CONFIG_E500MC) + rlwinm r4,r0,27,27,31 + mr r5,r4 +#else + mr r4,r0 + mr r5,r4 +#endif + + /* + * r10 has the base address for the entry. + * we cannot access it yet before setting up a new TLB + */ + slwi r8,r5,6 /* spin table is padded to 64 byte */ + add r10,r3,r8 + + mtspr SPRN_PIR,r4 /* write to PIR register */ + +#ifdef CONFIG_SYS_FSL_ERRATUM_A007907 + mfspr r8, L1CSR2 + clrrwi r8, r8, 10 /* clear bit [54-63] DCSTASHID */ + mtspr L1CSR2, r8 +#else +#ifdef CONFIG_SYS_CACHE_STASHING + /* set stash id to (coreID) * 2 + 32 + L1 CT (0) */ + slwi r8,r4,1 + addi r8,r8,32 + mtspr L1CSR2,r8 +#endif +#endif /* CONFIG_SYS_FSL_ERRATUM_A007907 */ + +#if defined(CONFIG_SYS_P4080_ERRATUM_CPU22) || \ + defined(CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011) + /* + * CPU22 applies to P4080 rev 1.0, 2.0, fixed in 3.0 + * NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in 3.0 + * also appleis to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1 + */ + mfspr r3,SPRN_SVR + rlwinm r6,r3,24,~0x800 /* clear E bit */ + + lis r5,SVR_P4080@h + ori r5,r5,SVR_P4080@l + cmpw r6,r5 + bne 1f + + rlwinm r3,r3,0,0xf0 + li r5,0x30 + cmpw r3,r5 + bge 2f +1: +#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_CPU_A011 + lis r3,toreset(enable_cpu_a011_workaround)@ha + lwz r3,toreset(enable_cpu_a011_workaround)@l(r3) + cmpwi r3,0 + beq 2f +#endif + mfspr r3,L1CSR2 + oris r3,r3,(L1CSR2_DCWS)@h + mtspr L1CSR2,r3 +2: +#endif + +#ifdef CONFIG_SYS_FSL_ERRATUM_A005812 + /* + * A-005812 workaround sets bit 32 of SPR 976 for SoCs running in + * write shadow mode. This code should run after other code setting + * DCWS. + */ + mfspr r3,L1CSR2 + andis. r3,r3,(L1CSR2_DCWS)@h + beq 1f + mfspr r3, SPRN_HDBCR0 + oris r3, r3, 0x8000 + mtspr SPRN_HDBCR0, r3 +1: +#endif + +#ifdef CONFIG_BACKSIDE_L2_CACHE + /* skip L2 setup on P2040/P2040E as they have no L2 */ + mfspr r3,SPRN_SVR + rlwinm r6,r3,24,~0x800 /* clear E bit of SVR */ + + lis r3,SVR_P2040@h + ori r3,r3,SVR_P2040@l + cmpw r6,r3 + beq 3f + + /* Enable/invalidate the L2 cache */ + msync + lis r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@h + ori r2,r2,(L2CSR0_L2FI|L2CSR0_L2LFC)@l + mtspr SPRN_L2CSR0,r2 +1: + mfspr r3,SPRN_L2CSR0 + and. r1,r3,r2 + bne 1b + +#ifdef CONFIG_SYS_CACHE_STASHING + /* set stash id to (coreID) * 2 + 32 + L2 (1) */ + addi r3,r8,1 + mtspr SPRN_L2CSR1,r3 +#endif + + lis r3,CONFIG_SYS_INIT_L2CSR0@h + ori r3,r3,CONFIG_SYS_INIT_L2CSR0@l + mtspr SPRN_L2CSR0,r3 + isync +2: + mfspr r3,SPRN_L2CSR0 + andis. r1,r3,L2CSR0_L2E@h + beq 2b +#endif +3: + /* setup mapping for the spin table, WIMGE=0b00100 */ + lis r13,toreset(__spin_table_addr)@h + ori r13,r13,toreset(__spin_table_addr)@l + lwz r13,0(r13) + /* mask by 4K */ + rlwinm r13,r13,0,0,19 + + lis r11,(MAS0_TLBSEL(1)|MAS0_ESEL(1))@h + mtspr SPRN_MAS0,r11 + lis r11,(MAS1_VALID|MAS1_IPROT)@h + ori r11,r11,(MAS1_TS|MAS1_TSIZE(BOOKE_PAGESZ_4K))@l + mtspr SPRN_MAS1,r11 + oris r11,r13,(MAS2_M|MAS2_G)@h + ori r11,r13,(MAS2_M|MAS2_G)@l + mtspr SPRN_MAS2,r11 + oris r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@h + ori r11,r13,(MAS3_SX|MAS3_SW|MAS3_SR)@l + mtspr SPRN_MAS3,r11 + li r11,0 + mtspr SPRN_MAS7,r11 + tlbwe + + /* + * __bootpg_addr has the address of __second_half_boot_page + * jump there in AS=1 space with cache enabled + */ + lis r13,toreset(__bootpg_addr)@h + ori r13,r13,toreset(__bootpg_addr)@l + lwz r11,0(r13) + mtspr SPRN_SRR0,r11 + mfmsr r13 + ori r12,r13,MSR_IS|MSR_DS@l + mtspr SPRN_SRR1,r12 + rfi + + /* + * Allocate some space for the SDRAM address of the bootpg. + * This variable has to be in the boot page so that it can + * be accessed by secondary cores when they come out of reset. + */ + .align L1_CACHE_SHIFT + .globl __bootpg_addr +__bootpg_addr: + .long 0 + + .global __spin_table_addr +__spin_table_addr: + .long 0 + + /* + * This variable is set by cpu_init_r() after parsing hwconfig + * to enable workaround for erratum NMG_CPU_A011. + */ + .align L1_CACHE_SHIFT + .global enable_cpu_a011_workaround +enable_cpu_a011_workaround: + .long 1 + + /* Fill in the empty space. The actual reset vector is + * the last word of the page */ +__secondary_start_code_end: + .space 4092 - (__secondary_start_code_end - __secondary_start_page) +__secondary_reset_vector: + b __secondary_start_page + + +/* this is a separated page for the spin table and cacheable boot code */ + .align L1_CACHE_SHIFT + .global __second_half_boot_page +__second_half_boot_page: +#ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE + lis r3,(spin_table_compat - __second_half_boot_page)@h + ori r3,r3,(spin_table_compat - __second_half_boot_page)@l + add r3,r3,r11 /* r11 has the address of __second_half_boot_page */ + lwz r14,0(r3) +#endif + +#define ENTRY_ADDR_UPPER 0 +#define ENTRY_ADDR_LOWER 4 +#define ENTRY_R3_UPPER 8 +#define ENTRY_R3_LOWER 12 +#define ENTRY_RESV 16 +#define ENTRY_PIR 20 +#define ENTRY_SIZE 64 + /* + * setup the entry + * r10 has the base address of the spin table. + * spin table is defined as + * struct { + * uint64_t entry_addr; + * uint64_t r3; + * uint32_t rsvd1; + * uint32_t pir; + * }; + * we pad this struct to 64 bytes so each entry is in its own cacheline + */ + li r3,0 + li r8,1 + mfspr r4,SPRN_PIR + stw r3,ENTRY_ADDR_UPPER(r10) + stw r3,ENTRY_R3_UPPER(r10) + stw r4,ENTRY_R3_LOWER(r10) + stw r3,ENTRY_RESV(r10) + stw r4,ENTRY_PIR(r10) + msync + stw r8,ENTRY_ADDR_LOWER(r10) + + /* spin waiting for addr */ +3: +/* + * To comply with ePAPR 1.1, the spin table has been moved to cache-enabled + * memory. Old OS may not work with this change. A patch is waiting to be + * accepted for Linux kernel. Other OS needs similar fix to spin table. + * For OSes with old spin table code, we can enable this temporary fix by + * setting environmental variable "spin_table_compat". For new OSes, set + * "spin_table_compat=no". After Linux is fixed, we can remove this macro + * and related code. For now, it is enabled by default. + */ +#ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE + cmpwi r14,0 + beq 4f + dcbf 0, r10 + sync +4: +#endif + lwz r4,ENTRY_ADDR_LOWER(r10) + andi. r11,r4,1 + bne 3b + isync + + /* get the upper bits of the addr */ + lwz r11,ENTRY_ADDR_UPPER(r10) + + /* setup branch addr */ + mtspr SPRN_SRR0,r4 + + /* mark the entry as released */ + li r8,3 + stw r8,ENTRY_ADDR_LOWER(r10) + + /* mask by ~64M to setup our tlb we will jump to */ + rlwinm r12,r4,0,0,5 + + /* + * setup r3, r4, r5, r6, r7, r8, r9 + * r3 contains the value to put in the r3 register at secondary cpu + * entry. The high 32-bits are ignored on 32-bit chip implementations. + * 64-bit chip implementations however shall load all 64-bits + */ +#ifdef CONFIG_SYS_PPC64 + ld r3,ENTRY_R3_UPPER(r10) +#else + lwz r3,ENTRY_R3_LOWER(r10) +#endif + li r4,0 + li r5,0 + li r6,0 + lis r7,(64*1024*1024)@h + li r8,0 + li r9,0 + + /* load up the pir */ + lwz r0,ENTRY_PIR(r10) + mtspr SPRN_PIR,r0 + mfspr r0,SPRN_PIR + stw r0,ENTRY_PIR(r10) + + mtspr IVPR,r12 +/* + * Coming here, we know the cpu has one TLB mapping in TLB1[0] + * which maps 0xfffff000-0xffffffff one-to-one. We set up a + * second mapping that maps addr 1:1 for 64M, and then we jump to + * addr + */ + lis r10,(MAS0_TLBSEL(1)|MAS0_ESEL(0))@h + mtspr SPRN_MAS0,r10 + lis r10,(MAS1_VALID|MAS1_IPROT)@h + ori r10,r10,(MAS1_TSIZE(BOOKE_PAGESZ_64M))@l + mtspr SPRN_MAS1,r10 + /* WIMGE = 0b00000 for now */ + mtspr SPRN_MAS2,r12 + ori r12,r12,(MAS3_SX|MAS3_SW|MAS3_SR) + mtspr SPRN_MAS3,r12 +#ifdef CONFIG_ENABLE_36BIT_PHYS + mtspr SPRN_MAS7,r11 +#endif + tlbwe + +/* Now we have another mapping for this page, so we jump to that + * mapping + */ + mtspr SPRN_SRR1,r13 + rfi + + + .align 6 + .globl __spin_table +__spin_table: + .space CONFIG_MAX_CPUS*ENTRY_SIZE + +#ifdef CONFIG_PPC_SPINTABLE_COMPATIBLE + .align L1_CACHE_SHIFT + .global spin_table_compat +spin_table_compat: + .long 1 + +#endif + +__spin_table_end: + .space 4096 - (__spin_table_end - __spin_table) |