diff options
Diffstat (limited to 'roms/u-boot/doc/device-tree-bindings/pwm')
4 files changed, 141 insertions, 0 deletions
diff --git a/roms/u-boot/doc/device-tree-bindings/pwm/cros-ec-pwm.txt b/roms/u-boot/doc/device-tree-bindings/pwm/cros-ec-pwm.txt new file mode 100644 index 000000000..f198d0889 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/pwm/cros-ec-pwm.txt @@ -0,0 +1,23 @@ +PWM controlled by ChromeOS EC + +Google's ChromeOS EC PWM is a simple PWM attached to the Embedded Controller +(EC) and controlled via a host-command interface. + +An EC PWM node should be only found as a sub-node of the EC node (see +doc/device-tree-bindings/misc/cros-ec.txt). + +Required properties: +- compatible: Must contain "google,cros-ec-pwm" +- #pwm-cells: Should be 1. The cell specifies the PWM index. + +Example: + cros-ec@0 { + compatible = "google,cros-ec-spi"; + + ... + + cros_ec_pwm: ec-pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/pwm/pwm-sifive.txt b/roms/u-boot/doc/device-tree-bindings/pwm/pwm-sifive.txt new file mode 100644 index 000000000..9a988372c --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/pwm/pwm-sifive.txt @@ -0,0 +1,31 @@ +SiFive PWM controller + +Unlike most other PWM controllers, the SiFive PWM controller currently only +supports one period for all channels in the PWM. All PWMs need to run at +the same period. The period also has significant restrictions on the values +it can achieve, which the driver rounds to the nearest achievable period. +PWM RTL that corresponds to the IP block version numbers can be found +here: + +https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/pwm + +Required properties: +- compatible: Should be "sifive,<chip>-pwm" and "sifive,pwm<version>". + Supported compatible strings are: "sifive,fu540-c000-pwm" for the SiFive + PWM v0 as integrated onto the SiFive FU540 chip, and "sifive,pwm0" for the + SiFive PWM v0 IP block with no chip integration tweaks. +- reg: physical base address and length of the controller's registers +- clocks: Should contain a clock identifier for the PWM's parent clock. +- #pwm-cells: Should be 3. +- interrupts: one interrupt per PWM channel + +Examples: + +pwm: pwm@10020000 { + compatible = "sifive,fu540-c000-pwm", "sifive,pwm0"; + reg = <0x0 0x10020000 0x0 0x1000>; + clocks = <&tlclk>; + interrupt-parent = <&plic>; + interrupts = <42 43 44 45>; + #pwm-cells = <3>; +}; diff --git a/roms/u-boot/doc/device-tree-bindings/pwm/pwm.txt b/roms/u-boot/doc/device-tree-bindings/pwm/pwm.txt new file mode 100644 index 000000000..8556263b8 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/pwm/pwm.txt @@ -0,0 +1,69 @@ +Specifying PWM information for devices +====================================== + +1) PWM user nodes +----------------- + +PWM users should specify a list of PWM devices that they want to use +with a property containing a 'pwm-list': + + pwm-list ::= <single-pwm> [pwm-list] + single-pwm ::= <pwm-phandle> <pwm-specifier> + pwm-phandle : phandle to PWM controller node + pwm-specifier : array of #pwm-cells specifying the given PWM + (controller specific) + +PWM properties should be named "pwms". The exact meaning of each pwms +property must be documented in the device tree binding for each device. +An optional property "pwm-names" may contain a list of strings to label +each of the PWM devices listed in the "pwms" property. If no "pwm-names" +property is given, the name of the user node will be used as fallback. + +Drivers for devices that use more than a single PWM device can use the +"pwm-names" property to map the name of the PWM device requested by the +pwm_get() call to an index into the list given by the "pwms" property. + +The following example could be used to describe a PWM-based backlight +device: + + pwm: pwm { + #pwm-cells = <2>; + }; + + [...] + + bl: backlight { + pwms = <&pwm 0 5000000>; + pwm-names = "backlight"; + }; + +Note that in the example above, specifying the "pwm-names" is redundant +because the name "backlight" would be used as fallback anyway. + +pwm-specifier typically encodes the chip-relative PWM number and the PWM +period in nanoseconds. + +Optionally, the pwm-specifier can encode a number of flags (defined in +<dt-bindings/pwm/pwm.h>) in a third cell: +- PWM_POLARITY_INVERTED: invert the PWM signal polarity + +Example with optional PWM specifier for inverse polarity + + bl: backlight { + pwms = <&pwm 0 5000000 PWM_POLARITY_INVERTED>; + pwm-names = "backlight"; + }; + +2) PWM controller nodes +----------------------- + +PWM controller nodes must specify the number of cells used for the +specifier using the '#pwm-cells' property. + +An example PWM controller might look like this: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/pwm/tegra20-pwm.txt b/roms/u-boot/doc/device-tree-bindings/pwm/tegra20-pwm.txt new file mode 100644 index 000000000..01438ecd6 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/pwm/tegra20-pwm.txt @@ -0,0 +1,18 @@ +Tegra SoC PWFM controller + +Required properties: +- compatible: should be one of: + - "nvidia,tegra20-pwm" + - "nvidia,tegra30-pwm" +- reg: physical base address and length of the controller's registers +- #pwm-cells: On Tegra the number of cells used to specify a PWM is 2. The + first cell specifies the per-chip index of the PWM to use and the second + cell is the period in nanoseconds. + +Example: + + pwm: pwm@7000a000 { + compatible = "nvidia,tegra20-pwm"; + reg = <0x7000a000 0x100>; + #pwm-cells = <2>; + }; |