diff options
Diffstat (limited to 'roms/u-boot/doc/device-tree-bindings/video')
16 files changed, 917 insertions, 0 deletions
diff --git a/roms/u-boot/doc/device-tree-bindings/video/atmel-hlcdc.txt b/roms/u-boot/doc/device-tree-bindings/video/atmel-hlcdc.txt new file mode 100644 index 000000000..b378cbf9d --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/atmel-hlcdc.txt @@ -0,0 +1,42 @@ +Atmel HLCDC Framebuffer +----------------------------------------------------- +Required properties: +- compatible : + "atmel,sama5d2-hlcdc", "atmel,at91sam9x5-hlcdc". +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: phandles to input clocks. +- atmel,vl-bpix: Bits per pixel. +- atmel,output-mode: LCD Controller Output Mode, + The unit is bits per pixel, there are four values, + <12>, <16>, <18>, <24>, the default value is <24>. +- atmel,guard-time: lcd guard time (Delay in frame periods). +- display-timings: please refer the displaymode.txt. + +Example: +hlcdc: hlcdc@f0000000 { + u-boot,dm-pre-reloc; + compatible = "atmel,sama5d2-hlcdc"; + reg = <0xf0000000 0x2000>; + clocks = <&lcdc_clk>; + atmel,vl-bpix = <4>; + atmel,output-mode = <24>; + atmel,guard-time = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_pwm &pinctrl_lcd_rgb666>; + status = "okay"; + + display-timings { + 480x272 { + clock-frequency = <9000000>; + hactive = <480>; + vactive = <272>; + hsync-len = <41>; + hfront-porch = <2>; + hback-porch = <2>; + vfront-porch = <2>; + vback-porch = <2>; + vsync-len = <11>; + }; + }; +}; diff --git a/roms/u-boot/doc/device-tree-bindings/video/bridge/ps8622.txt b/roms/u-boot/doc/device-tree-bindings/video/bridge/ps8622.txt new file mode 100644 index 000000000..66d5d07eb --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/bridge/ps8622.txt @@ -0,0 +1,33 @@ +ps8622-bridge bindings + +Required properties: + - compatible: "parade,ps8622" or "parade,ps8625" + - reg: first i2c address of the bridge + - sleep-gpios: OF device-tree gpio specification for PD_ pin. + - reset-gpios: OF device-tree gpio specification for RST_ pin. + - parade,regs: List of 3-byte registers tuples to write: + <I2C chip address offset> <register> <value> + +Optional properties: + - lane-count: number of DP lanes to use + - use-external-pwm: backlight will be controlled by an external PWM + - video interfaces: Device node can contain video interface port + nodes for panel according to [1]. + +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + lvds-bridge@48 { + compatible = "parade,ps8622"; + reg = <0x48>; + sleep-gpios = <&gpc3 6 1 0 0>; + reset-gpios = <&gpc3 1 1 0 0>; + lane-count = <1>; + ports { + port@0 { + bridge_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/display-timing.txt b/roms/u-boot/doc/device-tree-bindings/video/display-timing.txt new file mode 100644 index 000000000..e1d4a0b59 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/display-timing.txt @@ -0,0 +1,110 @@ +display-timing bindings +======================= + +display-timings node +-------------------- + +required properties: + - none + +optional properties: + - native-mode: The native mode for the display, in case multiple modes are + provided. When omitted, assume the first node is the native. + +timing subnode +-------------- + +required properties: + - hactive, vactive: display resolution + - hfront-porch, hback-porch, hsync-len: horizontal display timing parameters + in pixels + vfront-porch, vback-porch, vsync-len: vertical display timing parameters in + lines + - clock-frequency: display clock in Hz + +optional properties: + - hsync-active: hsync pulse is active low/high/ignored + - vsync-active: vsync pulse is active low/high/ignored + - de-active: data-enable pulse is active low/high/ignored + - pixelclk-active: with + - active high = drive pixel data on rising edge/ + sample data on falling edge + - active low = drive pixel data on falling edge/ + sample data on rising edge + - ignored = ignored + - interlaced (bool): boolean to enable interlaced mode + - doublescan (bool): boolean to enable doublescan mode + - doubleclk (bool): boolean to enable doubleclock mode + +All the optional properties that are not bool follow the following logic: + <1>: high active + <0>: low active + omitted: not used on hardware + +There are different ways of describing the capabilities of a display. The +devicetree representation corresponds to the one commonly found in datasheets +for displays. If a display supports multiple signal timings, the native-mode +can be specified. + +The parameters are defined as: + + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vback_porch | | | + | | ↓ | | | + +----------#######################################----------+-------+ + | # ↑ # | | + | # | # | | + | hback # | # hfront | hsync | + | porch # | hactive # porch | len | + |<-------->#<-------+--------------------------->#<-------->|<----->| + | # | # | | + | # |vactive # | | + | # | # | | + | # ↓ # | | + +----------#######################################----------+-------+ + | | ↑ | | | + | | |vfront_porch | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + | | ↑ | | | + | | |vsync_len | | | + | | ↓ | | | + +----------+-------------------------------------+----------+-------+ + +Example: + + display-timings { + native-mode = <&timing0>; + timing0: 1080p24 { + /* 1920x1080p24 */ + clock-frequency = <52000000>; + hactive = <1920>; + vactive = <1080>; + hfront-porch = <25>; + hback-porch = <25>; + hsync-len = <25>; + vback-porch = <2>; + vfront-porch = <2>; + vsync-len = <2>; + hsync-active = <1>; + }; + }; + +Every required property also supports the use of ranges, so the commonly used +datasheet description with minimum, typical and maximum values can be used. + +Example: + + timing1: timing { + /* 1920x1080p24 */ + clock-frequency = <148500000>; + hactive = <1920>; + vactive = <1080>; + hsync-len = <0 44 60>; + hfront-porch = <80 88 95>; + hback-porch = <100 148 160>; + vfront-porch = <0 4 6>; + vback-porch = <0 36 50>; + vsync-len = <0 5 6>; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/displaymode.txt b/roms/u-boot/doc/device-tree-bindings/video/displaymode.txt new file mode 100644 index 000000000..45ca42db5 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/displaymode.txt @@ -0,0 +1,42 @@ +videomode bindings +================== + +(from http://lists.freedesktop.org/archives/dri-devel/2012-July/024875.html) + +Required properties: + - xres, yres: Display resolution + - left-margin, right-margin, hsync-len: Horizontal Display timing + parameters in pixels + - upper-margin, lower-margin, vsync-len: Vertical display timing + parameters in lines + - clock: display clock in Hz + +Optional properties: + - width-mm, height-mm: Display dimensions in mm + - hsync-active-high (bool): Hsync pulse is active high + - vsync-active-high (bool): Vsync pulse is active high + - interlaced (bool): This is an interlaced mode + - doublescan (bool): This is a doublescan mode + +There are different ways of describing a display mode. The devicetree +representation corresponds to the one used by the Linux Framebuffer +framework described here in Documentation/fb/framebuffer.txt. This +representation has been chosen because it's the only format which does +not allow for inconsistent parameters. Unlike the Framebuffer framework +the devicetree has the clock in Hz instead of ps. + +Example: + + display@0 { + /* 1920x1080p24 */ + clock = <52000000>; + xres = <1920>; + yres = <1080>; + left-margin = <25>; + right-margin = <25>; + hsync-len = <25>; + lower-margin = <2>; + upper-margin = <2>; + vsync-len = <2>; + hsync-active-high; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/exynos-dp.txt b/roms/u-boot/doc/device-tree-bindings/video/exynos-dp.txt new file mode 100644 index 000000000..464a85302 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/exynos-dp.txt @@ -0,0 +1,69 @@ +Exynos Display port controller +============================== + +Required properties: +SOC specific: + compatible: should be "samsung,exynos5-dp" + reg: Base address of DP IP + +Optional properties: + samsung,h-res: X resolution of the panel + samsung,h-sync-width: hsync value + samsung,h-back-porch: left margin + samsung,h-front-porch right margin + samsung,v-res: Y resolution of the panel + samsung,v-sync-width: vsync value + samsung,v-back-porch: upper margin + samsung,v-front-porch: lower margin + samsung,v-sync-rate: refresh rate + + samsung,lt-status: Link training status + 0(DP_LT_NONE), 1(DP_LT_START), 2(DP_LT_CR), 3(DP_LT_ET), + 4(DP_LT_FINISHED), 5(DP_LT_FAIL) + + samsung,master-mode: 1 if you want to run DP as master, else 0 + samsung,bist-mode: 1 to enable video bist mode, else 0 + samsung,bist-pattern: bist mode pattern type + 0(NO_PATTERN), 1(COLOR_RAMP), 2(BALCK_WHITE_V_LINES), + 3(COLOR_SQUARE), 4(INVALID_PATTERN), 5(COLORBAR_32), + 6(COLORBAR_64),7(WHITE_GRAY_BALCKBAR_32), + 8(WHITE_GRAY_BALCKBAR_64),9(MOBILE_WHITEBAR_32), + 10(MOBILE_WHITEBAR_64) + samsung,h-sync-polarity: Horizontal Sync polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,v-sync-polarity: Vertical Sync polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,interlaced: Progressive if 0, else Interlaced + samsung,color-space: input video data format + COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2 + samsung,dynamic-range: dynamic range for input video data + VESA = 0, CEA = 1 + samsung,ycbcr-coeff: YCbCr co-efficients for input video + COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1 + samsung,color-depth: number of bits per colour component + COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3 + +Example: +SOC specific part: + dp@145b0000 { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + }; + +Board(panel) specific part: + dp@145b0000 { + samsung,lt-status = <0>; + + samsung,master-mode = <0>; + samsung,bist-mode = <0>; + samsung,bist-pattern = <0>; + samsung,h-sync-polarity = <0>; + samsung,v-sync-polarity = <0>; + samsung,interlaced = <0>; + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/exynos-fb.txt b/roms/u-boot/doc/device-tree-bindings/video/exynos-fb.txt new file mode 100644 index 000000000..b022f6163 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/exynos-fb.txt @@ -0,0 +1,100 @@ +Exynos Display Controller +========================= +Required properties: +SOC specific: + compatible: should be "samsung,exynos-fimd" + reg: Base address of FIMD IP. + +Board(panel specific): + samsung,vl-col: X resolution of the panel + samsung,vl-row: Y resolution of the panel + samsung,vl-freq: Refresh rate + samsung,vl-bpix: Bits per pixel + samsung,vl-hspw: Hsync value + samsung,vl-hfpd: Right margin + samsung,vl-hbpd: Left margin + samsung,vl-vspw: Vsync value + samsung,vl-vfpd: Lower margin + samsung,vl-vbpd: Upper margin + +Optional properties: +Board(panel specific): + samsung,vl-width: width of display area in mm + samsung,vl-height: Height of display area in mm + + samsung,vl-clkp: Clock polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-oep: Output Enable polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-hsp: Horizontal Sync polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-vsp: Vertical Sync polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + samsung,vl-dp: Data polarity + CONFIG_SYS_LOW if defined, else CONFIG_SYS_HIGH + + samsung,vl-cmd-allow-len: Wait end of frame + samsung,winid: Window number on which data is to be displayed + samsung,init-delay: Delay before LCD initialization starts + samsung,power-on-delay: Delay after LCD is powered on + samsung,reset-delay: Delay after LCD is reset + samsung,interface-mode: 1(FIMD_RGB_INTERFACE), 2(FIMD_CPU_INTERFACE) + samsung,mipi-enabled: 1 if you want to use MIPI, else 0 + samsung,dp-enabled: 1is you want to use DP, else 0 + samsung,cs-setup: cs_setup value in FIMD_CPU_INTERFACE mode. + samsung,wr-setup: wr_setup value in FIMD_CPU_INTERFACE mode. + samsung,wr-act: wr_act value in FIMD_CPU_INTERFACE mode. + samsung,wr-hold: wr_hold value in FIMD_CPU_INTERFACE mode. + samsung,logo-on: 1 if you want to use custom logo. + 0 if you want LCD console. + samsung,logo-width: pixel width of logo image. Valid if logo_on = 1 + samsung,logo-height: pixel height of logo image. Valid if logo_on = 1 + samsung,logo-addr: Address of logo image. Valid if logo_on = 1 + samsung,rgb-mode: 0(MODE_RGB_P), 1(MODE_BGR_P), + 2(MODE_RGB_S), 3(MODE_BGR_S) + samsung,pclk-name: parent clock identifier: 1(MPLL), 2(EPLL), 3(VPLL) + samsung,sclk-div: parent_clock/source_clock ratio + samsung,dual-lcd-enabled: 1 if you support two LCD, else 0 + samsung,disable-sysmmu: Define this if you want to disable FIMD sysmmu. + (needed for Exynos5420 and newer versions) + Add the required FIMD sysmmu nodes to be + disabled with compatible string + "samsung,sysmmu-v3.3", with a "reg" property + holding the register address of FIMD sysmmu. + samsung,pwm-out-gpio: PWM output GPIO. + samsung,bl-en-gpio: backlight enable GPIO. + +Example: +SOC specific part: + fimd@14400000 { + compatible = "samsung,exynos-fimd"; + reg = <0x14400000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; + }; + +Board specific part: + fimd@14400000 { + samsung,vl-freq = <60>; + samsung,vl-col = <2560>; + samsung,vl-row = <1600>; + samsung,vl-width = <2560>; + samsung,vl-height = <1600>; + + samsung,vl-clkp; + samsung,vl-dp; + samsung,vl-bpix = <4>; + + samsung,vl-hspw = <32>; + samsung,vl-hbpd = <80>; + samsung,vl-hfpd = <48>; + samsung,vl-vspw = <6>; + samsung,vl-vbpd = <37>; + samsung,vl-vfpd = <3>; + samsung,vl-cmd-allow-len = <0xf>; + + samsung,winid = <3>; + samsung,interface-mode = <1>; + samsung,dp-enabled = <1>; + samsung,dual-lcd-enabled = <0>; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/exynos_mipi_dsi.txt b/roms/u-boot/doc/device-tree-bindings/video/exynos_mipi_dsi.txt new file mode 100644 index 000000000..4938ea01e --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/exynos_mipi_dsi.txt @@ -0,0 +1,82 @@ +Exynos MIPI-DSIM Controller +========================= + +Required properties: +SOC specific: + compatible: should be "samsung,exynos-mipi-dsi" + reg: Base address of MIPI-DSIM IP. + +Board specific: + samsung,dsim-config-e-interface: interface to be used (RGB interface + for main display or CPU interface for main or sub display). + samsung,dsim-config-e-virtual-ch: virtual channel number that main + or sub display uses. + samsung,dsim-config-e-pixel-format: pixel stream format for main + or sub display. + samsung,dsim-config-e-burst-mode: selects Burst mode in Video mode. + in Non-burst mode, RGB data area is filled with RGB data and + NULL packets, according to input bandwidth of RGB interface. + samsung,dsim-config-e-no-data-lane: data lane count used by Master. + samsung,dsim-config-e-byte-clk: select byte clock source. + It must be DSIM_PLL_OUT_DIV8. + DSIM_EXT_CLK_DIV8 and DSIM_EXT_CLK_BYPASSS are not supported. + samsung,dsim-config-hfp: HFP disable mode. + If set, DSI master ignores HFP area in VIDEO mode. + In command mode, this variable is ignored. + samsung,dsim-config-p: P value for PMS setting. + samsung,dsim-config-m: M value for PMS setting. + samsung,dsim-config-s: S value for PMS setting. + samsung,dsim-config-pll-stable-time: the PLL Timer for stability + of the ganerated clock. + samsung,dsim-config-esc-clk: escape clock frequency for getting + the escape clock prescaler value. + samsung,dsim-config-stop-holding-cnt: the interval value between + transmitting read packet (or write "set_tear_on" command) + and BTA request. After transmitting read packet or write + "set_tear_on" command, BTA requests to D-PHY automatically. + This counter value specifies the interval between them. + samsung,dsim-config-bta-timeout: the timer for BTA. This register + specifies time out from BTA request to change the direction + with respect to Tx escape clock. + samsung,dsim-config-rx-timeout: the timer for LP Rx mode timeout. + this register specifies time out on how long RxValid deasserts, + after RxLpdt asserts with respect to Tx escape clock. + - RxValid specifies Rx data valid indicator. + - RxLpdt specifies an indicator that D-PHY is under RxLpdt mode + - RxValid and RxLpdt specifies signal from D-PHY. + samsung,dsim-device-name: name of the device. + samsung,dsim-device-id: unique device id. + samsung,dsim-device-bus_id: bus id for identifing connected bus + and this bus id should be same as id of mipi_dsim_device. + +Optional properties: + samsung,dsim-device-reverse-panel: reverse panel. + +Example: + mipidsi@11c80000 { + compatible = "samsung,exynos-mipi-dsi"; + reg = <0x11c80000 0x5c>; + + samsung,dsim-config-e-interface = <1>; + samsung,dsim-config-e-virtual-ch = <0>; + samsung,dsim-config-e-pixel-format = <7>; + samsung,dsim-config-e-burst-mode = <1>; + samsung,dsim-config-e-no-data-lane = <3>; + samsung,dsim-config-e-byte-clk = <0>; + samsung,dsim-config-hfp = <1>; + + samsung,dsim-config-p = <3>; + samsung,dsim-config-m = <120>; + samsung,dsim-config-s = <1>; + + samsung,dsim-config-pll-stable-time = <500>; + samsung,dsim-config-esc-clk = <20000000>; + samsung,dsim-config-stop-holding-cnt = <0x7ff>; + samsung,dsim-config-bta-timeout = <0xff>; + samsung,dsim-config-rx-timeout = <0xffff>; + + samsung,dsim-device-id = <0xffffffff>; + samsung,dsim-device-bus-id = <0>; + + samsung,dsim-device-reverse-panel = <1>; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/intel-gma.txt b/roms/u-boot/doc/device-tree-bindings/video/intel-gma.txt new file mode 100644 index 000000000..914be4fed --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/intel-gma.txt @@ -0,0 +1,40 @@ +Intel GMA Bindings +================== + +This is the Intel Graphics Media Accelerator. This binding supports selection +of display parameters only. + + +Required properties: + - compatible : "intel,gma"; + +Optional properties: + - intel,dp-hotplug : values for digital port hotplug, one cell per value for + ports B, C and D + - intel,panel-port-select : output port to use: 0=LVDS 1=DP_B 2=DP_C 3=DP_D + - intel,panel-power-cycle-delay : T4 time sequence (6 = 500ms) + + The following delays are in units of 0.1ms: + - intel,panel-power-up-delay : T1+T2 time sequence + - intel,panel-power-down-delay : T3 time sequence + - intel,panel-power-backlight-on-delay : T5 time sequence + - intel,panel-power-backlight-off-delay : Tx time sequence + + - intel,cpu-backlight : Value for CPU Backlight PWM + - intel,pch-backlight : Value for PCH Backlight PWM + +Example +------- + +gma { + compatible = "intel,gma"; + intel,dp_hotplug = <0 0 0x06>; + intel,panel-port-select = <1>; + intel,panel-power-cycle-delay = <6>; + intel,panel-power-up-delay = <2000>; + intel,panel-power-down-delay = <500>; + intel,panel-power-backlight-on-delay = <2000>; + intel,panel-power-backlight-off-delay = <2000>; + intel,cpu-backlight = <0x00000200>; + intel,pch-backlight = <0x04000000>; +}; diff --git a/roms/u-boot/doc/device-tree-bindings/video/osd/gdsys,ihs_video_out.txt b/roms/u-boot/doc/device-tree-bindings/video/osd/gdsys,ihs_video_out.txt new file mode 100644 index 000000000..d7aacc827 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/osd/gdsys,ihs_video_out.txt @@ -0,0 +1,23 @@ +* Guntermann & Drunck Integrated Hardware Systems OSD + +Required properties: +- compatible: "gdsys,ihs_video_out" +- reg: A combination of three register spaces: + - Register base for the video registers + - Register base for the OSD registers + - Address of the OSD video memory +- mode: The initial resolution and frequency: "1024_768_60", "720_400_70", or + "640_480_70" +- clk_gen: phandle to the pixel clock generator +- dp_tx: phandle to the display associated with the OSD + +Example: + +fpga0_video0 { + compatible = "gdsys,ihs_video_out"; + reg = <0x100 0x40 + 0x180 0x20 + 0x1000 0x1000>; + dp_tx = <&fpga0_dp_video0>; + clk_gen = <&fpga0_video0_clkgen>; +}; diff --git a/roms/u-boot/doc/device-tree-bindings/video/rockchip-lvds.txt b/roms/u-boot/doc/device-tree-bindings/video/rockchip-lvds.txt new file mode 100644 index 000000000..7432e2216 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/rockchip-lvds.txt @@ -0,0 +1,77 @@ +Rockchip LVDS interface +------------------ + +Required properties: +- compatible: "rockchip,rk3288-lvds"; + +- reg: physical base address of the controller and length + of memory mapped region. +- clocks: must include clock specifiers corresponding to entries in the + clock-names property. +- clock-names: must contain "pclk_lvds" + +- rockchip,grf: phandle to the general register files syscon + +- rockchip,data-mapping: should be <LVDS_FORMAT_VESA> or <LVDS_FORMAT_JEIDA>, + This describes how the color bits are laid out in the + serialized LVDS signal. +- rockchip,data-width : should be <18> or <24>; +- rockchip,output: should be <LVDS_OUTPUT_RGB>, <LVDS_OUTPUT_SINGLE> or + <LVDS_OUTPUT_DUAL>, This describes the output face. + +- display-timings : described by + doc/device-tree-bindings/video/display-timing.txt. + +Example: + lvds: lvds@ff96c000 { + compatible = "rockchip,rk3288-lvds"; + reg = <0xff96c000 0x4000>; + clocks = <&cru PCLK_LVDS_PHY>; + clock-names = "pclk_lvds"; + pinctrl-names = "default"; + pinctrl-0 = <&lcdc0_ctl>; + rockchip,grf = <&grf>; + status = "disabled"; + ports { + #address-cells = <1>; + #size-cells = <0>; + + lvds_in: port@0 { + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + lvds_in_vopb: endpoint@0 { + reg = <0>; + remote-endpoint = <&vopb_out_lvds>; + }; + lvds_in_vopl: endpoint@1 { + reg = <1>; + remote-endpoint = <&vopl_out_lvds>; + }; + }; + }; + }; + + &lvds { + rockchip,data-mapping = <LVDS_FORMAT_VESA>; + rockchip,data-width = <24>; + rockchip,output = <LVDS_OUTPUT_DUAL>; + rockchip,panel = <&panel>; + status = "okay"; + + display-timings { + timing@0 { + clock-frequency = <40000000>; + hactive = <1920>; + vactive = <1080>; + hsync-len = <44>; + hfront-porch = <88>; + hback-porch = <148>; + vfront-porch = <4>; + vback-porch = <36>; + vsync-len = <5>; + }; + }; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/sandbox-fb.txt b/roms/u-boot/doc/device-tree-bindings/video/sandbox-fb.txt new file mode 100644 index 000000000..230d25c23 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/sandbox-fb.txt @@ -0,0 +1,17 @@ +Sandbox LCD +=========== + +This uses the displaymode.txt binding except that only xres and yres are +required properties. Also an additional optional property is defined: + +log2-depth: Log base 2 of the U-Boot display buffer depth (4=16bpp, 5=32bpp). + If not provided, a value of 4 is used. + +Example: + + lcd { + compatible = "sandbox,lcd-sdl"; + xres = <800>; + yres = <600>; + log2-depth = <5>; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/simple-framebuffer.txt b/roms/u-boot/doc/device-tree-bindings/video/simple-framebuffer.txt new file mode 100644 index 000000000..3ea460583 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/simple-framebuffer.txt @@ -0,0 +1,25 @@ +Simple Framebuffer + +A simple frame-buffer describes a raw memory region that may be rendered to, +with the assumption that the display hardware has already been set up to scan +out from that buffer. + +Required properties: +- compatible: "simple-framebuffer" +- reg: Should contain the location and size of the framebuffer memory. +- width: The width of the framebuffer in pixels. +- height: The height of the framebuffer in pixels. +- stride: The number of bytes in each line of the framebuffer. +- format: The format of the framebuffer surface. Valid values are: + - r5g6b5 (16-bit pixels, d[15:11]=r, d[10:5]=g, d[4:0]=b). + +Example: + + framebuffer { + compatible = "simple-framebuffer"; + reg = <0x1d385000 (1600 * 1200 * 2)>; + width = <1600>; + height = <1200>; + stride = <(1600 * 2)>; + format = "r5g6b5"; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/syncoam,seps525.txt b/roms/u-boot/doc/device-tree-bindings/video/syncoam,seps525.txt new file mode 100644 index 000000000..e1e0db9d7 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/syncoam,seps525.txt @@ -0,0 +1,24 @@ +spi based seps525 framebuffer display driver + +Driver for seps525 display controller (in spi mode), This binding supports selection +of spi chipselect, spi max frequency, gpio to drive dc and reset pin of seps525 +controller and spi transaction bit length. + +Required properties: +- compatible: "syncoam,seps525" +- reg: Specifies the chip-select the seps525 is connected to on the spi bus +- reset-gpios: gpio connected to reset pin of seps525 controller. +- dc-gpios: gpio connected to dc pin of seps525 controller: +- buswidth: bitlength of each spi transaction + +Example: + displayspi@0 { + compatible = "syncoam,seps525"; + reg = <0>; + spi-max-frequency = <10000000>; + spi-cpol; + spi-cpha; + buswidth = <8>; + reset-gpios = <&gpio 0x1c GPIO_ACTIVE_LOW>; + dc-gpios = <&gpio 0x1b GPIO_ACTIVE_HIGH>; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/tegra20-dc.txt b/roms/u-boot/doc/device-tree-bindings/video/tegra20-dc.txt new file mode 100644 index 000000000..4731c3fba --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/tegra20-dc.txt @@ -0,0 +1,85 @@ +Display Controller +------------------ + +(there isn't yet a generic binding in Linux, so this describes what is in +U-Boot, and may change based on Linux activity) + +The device node for a display device is as described in the document +"Open Firmware Recommended Practice : Universal Serial Bus" with the +following modifications and additions : + +Required properties : + - compatible : Should be "nvidia,tegra20-dc" + +Required subnode 'rgb' is as follows: + +Required properties (rgb) : + - nvidia,panel : phandle of LCD panel information + + +The panel node describes the panel itself. This has the properties listed in +displaymode.txt as well as: + +Required properties (panel) : + - nvidia,bits-per-pixel: number of bits per pixel (depth) + - nvidia,pwm : pwm to use to set display contrast (see tegra20-pwm.txt) + - nvidia,panel-timings: 4 cells containing required timings in ms: + * delay before asserting panel_vdd + * delay between panel_vdd-rise and data-rise + * delay between data-rise and backlight_vdd-rise + * delay between backlight_vdd and pwm-rise + * delay between pwm-rise and backlight_en-rise + +Optional GPIO properies all have (phandle, GPIO number, flags): + - nvidia,backlight-enable-gpios: backlight enable GPIO + - nvidia,lvds-shutdown-gpios: LVDS power shutdown GPIO + - nvidia,backlight-vdd-gpios: backlight power GPIO + - nvidia,panel-vdd-gpios: panel power GPIO + +Example: + +host1x { + compatible = "nvidia,tegra20-host1x", "simple-bus"; + reg = <0x50000000 0x00024000>; + interrupts = <0 65 0x04 /* mpcore syncpt */ + 0 67 0x04>; /* mpcore general */ + + #address-cells = <1>; + #size-cells = <1>; + status = "okay"; + + ranges = <0x54000000 0x54000000 0x04000000>; + + dc@54200000 { + compatible = "nvidia,tegra20-dc"; + reg = <0x54200000 0x00040000>; + interrupts = <0 73 0x04>; + status = "okay"; + + rgb { + status = "okay"; + nvidia,panel = <&lcd_panel>; + }; + }; +}; + +lcd_panel: panel { + /* Seaboard has 1366x768 */ + clock = <70600000>; + xres = <1366>; + yres = <768>; + left-margin = <58>; + right-margin = <58>; + hsync-len = <58>; + lower-margin = <4>; + upper-margin = <4>; + vsync-len = <4>; + hsync-active-high; + nvidia,bits-per-pixel = <16>; + nvidia,pwm = <&pwm 2 0>; + nvidia,backlight-enable-gpios = <&gpio 28 0>; /* PD4 */ + nvidia,lvds-shutdown-gpios = <&gpio 10 0>; /* PB2 */ + nvidia,backlight-vdd-gpios = <&gpio 176 0>; /* PW0 */ + nvidia,panel-vdd-gpios = <&gpio 22 0>; /* PC6 */ + nvidia,panel-timings = <400 4 203 17 15>; +}; diff --git a/roms/u-boot/doc/device-tree-bindings/video/tilcdc/panel.txt b/roms/u-boot/doc/device-tree-bindings/video/tilcdc/panel.txt new file mode 100644 index 000000000..808216310 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/tilcdc/panel.txt @@ -0,0 +1,66 @@ +Device-Tree bindings for tilcdc DRM generic panel output driver + +Required properties: + - compatible: value should be "ti,tilcdc,panel". + - panel-info: configuration info to configure LCDC correctly for the panel + - ac-bias: AC Bias Pin Frequency + - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt + - dma-burst-sz: DMA burst size + - bpp: Bits per pixel + - fdd: FIFO DMA Request Delay + - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling + - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore + - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most + - fifo-th: DMA FIFO threshold + - display-timings: typical videomode of lcd panel. Multiple video modes + can be listed if the panel supports multiple timings, but the 'native-mode' + should be the preferred/default resolution. Refer to + Documentation/devicetree/bindings/display/panel/display-timing.txt for display + timing binding details. + +Optional properties: +- backlight: phandle of the backlight device attached to the panel +- enable-gpios: GPIO pin to enable or disable the panel + +Recommended properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure + muxing properly for pins that connect to TFP410 device + +Example: + + /* Settings for CDTech_S035Q01 / LCD3 cape: */ + lcd3 { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default"; + pinctrl-0 = <&bone_lcd3_cape_lcd_pins>; + backlight = <&backlight>; + enable-gpios = <&gpio3 19 0>; + + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <16>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + native-mode = <&timing0>; + timing0: 320x240 { + hactive = <320>; + vactive = <240>; + hback-porch = <21>; + hfront-porch = <58>; + hsync-len = <47>; + vback-porch = <11>; + vfront-porch = <23>; + vsync-len = <2>; + clock-frequency = <8000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; diff --git a/roms/u-boot/doc/device-tree-bindings/video/tilcdc/tilcdc.txt b/roms/u-boot/doc/device-tree-bindings/video/tilcdc/tilcdc.txt new file mode 100644 index 000000000..7bf1bb444 --- /dev/null +++ b/roms/u-boot/doc/device-tree-bindings/video/tilcdc/tilcdc.txt @@ -0,0 +1,82 @@ +Device-Tree bindings for tilcdc DRM driver + +Required properties: + - compatible: value should be one of the following: + - "ti,am33xx-tilcdc" for AM335x based boards + - "ti,da850-tilcdc" for DA850/AM18x/OMAP-L138 based boards + - interrupts: the interrupt number + - reg: base address and size of the LCDC device + +Recommended properties: + - ti,hwmods: Name of the hwmod associated to the LCDC + +Optional properties: + - max-bandwidth: The maximum pixels per second that the memory + interface / lcd controller combination can sustain + - max-width: The maximum horizontal pixel width supported by + the lcd controller. + - max-pixelclock: The maximum pixel clock that can be supported + by the lcd controller in KHz. + - blue-and-red-wiring: Recognized values "straight" or "crossed". + This property deals with the LCDC revision 2 (found on AM335x) + color errata [1]. + - "straight" indicates normal wiring that supports RGB565, + BGR888, and XBGR8888 color formats. + - "crossed" indicates wiring that has blue and red wires + crossed. This setup supports BGR565, RGB888 and XRGB8888 + formats. + - If the property is not present or its value is not recognized + the legacy mode is assumed. This configuration supports RGB565, + RGB888 and XRGB8888 formats. However, depending on wiring, the red + and blue colors are swapped in either 16 or 24-bit color modes. + +Optional nodes: + + - port/ports: to describe a connection to an external encoder. The + binding follows Documentation/devicetree/bindings/graph.txt and + supports a single port with a single endpoint. + + - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and + Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting + tfp410 DVI encoder or lcd panel to lcdc + +[1] There is an errata about AM335x color wiring. For 16-bit color mode + the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]), + but for 24 bit color modes the wiring of blue and red components is + crossed and LCD_DATA[0:4] is for Red[3:7] and LCD_DATA[11:15] is + for Blue[3-7]. For more details see section 3.1.1 in AM335x + Silicon Errata: + http://www.ti.com/general/docs/lit/getliterature.tsp?baseLiteratureNumber=sprz360 + +Example: + + fb: fb@4830e000 { + compatible = "ti,am33xx-tilcdc", "ti,da850-tilcdc"; + reg = <0x4830e000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <36>; + ti,hwmods = "lcdc"; + + blue-and-red-wiring = "crossed"; + + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; + }; + + tda19988: tda19988 { + compatible = "nxp,tda998x"; + reg = <0x70>; + + pinctrl-names = "default", "off"; + pinctrl-0 = <&nxp_hdmi_bonelt_pins>; + pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>; + + port { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; |