diff options
Diffstat (limited to 'roms/u-boot/drivers/net/fec_mxc.c')
| -rw-r--r-- | roms/u-boot/drivers/net/fec_mxc.c | 1612 |
1 files changed, 1612 insertions, 0 deletions
diff --git a/roms/u-boot/drivers/net/fec_mxc.c b/roms/u-boot/drivers/net/fec_mxc.c new file mode 100644 index 000000000..4fd5c01b4 --- /dev/null +++ b/roms/u-boot/drivers/net/fec_mxc.c @@ -0,0 +1,1612 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2009 Ilya Yanok, Emcraft Systems Ltd <yanok@emcraft.com> + * (C) Copyright 2008,2009 Eric Jarrige <eric.jarrige@armadeus.org> + * (C) Copyright 2008 Armadeus Systems nc + * (C) Copyright 2007 Pengutronix, Sascha Hauer <s.hauer@pengutronix.de> + * (C) Copyright 2007 Pengutronix, Juergen Beisert <j.beisert@pengutronix.de> + */ + +#include <common.h> +#include <cpu_func.h> +#include <dm.h> +#include <env.h> +#include <log.h> +#include <malloc.h> +#include <memalign.h> +#include <miiphy.h> +#include <net.h> +#include <netdev.h> +#include <asm/cache.h> +#include <asm/global_data.h> +#include <linux/delay.h> +#include <power/regulator.h> + +#include <asm/io.h> +#include <linux/errno.h> +#include <linux/compiler.h> + +#include <asm/arch/clock.h> +#include <asm/arch/imx-regs.h> +#include <asm/mach-imx/sys_proto.h> +#include <asm-generic/gpio.h> + +#include "fec_mxc.h" +#include <eth_phy.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Timeout the transfer after 5 mS. This is usually a bit more, since + * the code in the tightloops this timeout is used in adds some overhead. + */ +#define FEC_XFER_TIMEOUT 5000 + +/* + * The standard 32-byte DMA alignment does not work on mx6solox, which requires + * 64-byte alignment in the DMA RX FEC buffer. + * Introduce the FEC_DMA_RX_MINALIGN which can cover mx6solox needs and also + * satisfies the alignment on other SoCs (32-bytes) + */ +#define FEC_DMA_RX_MINALIGN 64 + +#ifndef CONFIG_MII +#error "CONFIG_MII has to be defined!" +#endif + +#ifndef CONFIG_FEC_XCV_TYPE +#define CONFIG_FEC_XCV_TYPE MII100 +#endif + +/* + * The i.MX28 operates with packets in big endian. We need to swap them before + * sending and after receiving. + */ +#ifdef CONFIG_MX28 +#define CONFIG_FEC_MXC_SWAP_PACKET +#endif + +#define RXDESC_PER_CACHELINE (ARCH_DMA_MINALIGN/sizeof(struct fec_bd)) + +/* Check various alignment issues at compile time */ +#if ((ARCH_DMA_MINALIGN < 16) || (ARCH_DMA_MINALIGN % 16 != 0)) +#error "ARCH_DMA_MINALIGN must be multiple of 16!" +#endif + +#if ((PKTALIGN < ARCH_DMA_MINALIGN) || \ + (PKTALIGN % ARCH_DMA_MINALIGN != 0)) +#error "PKTALIGN must be multiple of ARCH_DMA_MINALIGN!" +#endif + +#undef DEBUG + +#ifdef CONFIG_FEC_MXC_SWAP_PACKET +static void swap_packet(uint32_t *packet, int length) +{ + int i; + + for (i = 0; i < DIV_ROUND_UP(length, 4); i++) + packet[i] = __swab32(packet[i]); +} +#endif + +/* MII-interface related functions */ +static int fec_mdio_read(struct ethernet_regs *eth, uint8_t phyaddr, + uint8_t regaddr) +{ + uint32_t reg; /* convenient holder for the PHY register */ + uint32_t phy; /* convenient holder for the PHY */ + uint32_t start; + int val; + + /* + * reading from any PHY's register is done by properly + * programming the FEC's MII data register. + */ + writel(FEC_IEVENT_MII, ð->ievent); + reg = regaddr << FEC_MII_DATA_RA_SHIFT; + phy = phyaddr << FEC_MII_DATA_PA_SHIFT; + + writel(FEC_MII_DATA_ST | FEC_MII_DATA_OP_RD | FEC_MII_DATA_TA | + phy | reg, ð->mii_data); + + /* wait for the related interrupt */ + start = get_timer(0); + while (!(readl(ð->ievent) & FEC_IEVENT_MII)) { + if (get_timer(start) > (CONFIG_SYS_HZ / 1000)) { + printf("Read MDIO failed...\n"); + return -1; + } + } + + /* clear mii interrupt bit */ + writel(FEC_IEVENT_MII, ð->ievent); + + /* it's now safe to read the PHY's register */ + val = (unsigned short)readl(ð->mii_data); + debug("%s: phy: %02x reg:%02x val:%#x\n", __func__, phyaddr, + regaddr, val); + return val; +} + +#ifndef imx_get_fecclk +u32 __weak imx_get_fecclk(void) +{ + return 0; +} +#endif + +static int fec_get_clk_rate(void *udev, int idx) +{ + struct fec_priv *fec; + struct udevice *dev; + int ret; + + if (IS_ENABLED(CONFIG_IMX8) || + CONFIG_IS_ENABLED(CLK_CCF)) { + dev = udev; + if (!dev) { + ret = uclass_get_device(UCLASS_ETH, idx, &dev); + if (ret < 0) { + debug("Can't get FEC udev: %d\n", ret); + return ret; + } + } + + fec = dev_get_priv(dev); + if (fec) + return fec->clk_rate; + + return -EINVAL; + } else { + return imx_get_fecclk(); + } +} + +static void fec_mii_setspeed(struct ethernet_regs *eth) +{ + /* + * Set MII_SPEED = (1/(mii_speed * 2)) * System Clock + * and do not drop the Preamble. + * + * The i.MX28 and i.MX6 types have another field in the MSCR (aka + * MII_SPEED) register that defines the MDIO output hold time. Earlier + * versions are RAZ there, so just ignore the difference and write the + * register always. + * The minimal hold time according to IEE802.3 (clause 22) is 10 ns. + * HOLDTIME + 1 is the number of clk cycles the fec is holding the + * output. + * The HOLDTIME bitfield takes values between 0 and 7 (inclusive). + * Given that ceil(clkrate / 5000000) <= 64, the calculation for + * holdtime cannot result in a value greater than 3. + */ + u32 pclk; + u32 speed; + u32 hold; + int ret; + + ret = fec_get_clk_rate(NULL, 0); + if (ret < 0) { + printf("Can't find FEC0 clk rate: %d\n", ret); + return; + } + pclk = ret; + speed = DIV_ROUND_UP(pclk, 5000000); + hold = DIV_ROUND_UP(pclk, 100000000) - 1; + +#ifdef FEC_QUIRK_ENET_MAC + speed--; +#endif + writel(speed << 1 | hold << 8, ð->mii_speed); + debug("%s: mii_speed %08x\n", __func__, readl(ð->mii_speed)); +} + +static int fec_mdio_write(struct ethernet_regs *eth, uint8_t phyaddr, + uint8_t regaddr, uint16_t data) +{ + uint32_t reg; /* convenient holder for the PHY register */ + uint32_t phy; /* convenient holder for the PHY */ + uint32_t start; + + reg = regaddr << FEC_MII_DATA_RA_SHIFT; + phy = phyaddr << FEC_MII_DATA_PA_SHIFT; + + writel(FEC_MII_DATA_ST | FEC_MII_DATA_OP_WR | + FEC_MII_DATA_TA | phy | reg | data, ð->mii_data); + + /* wait for the MII interrupt */ + start = get_timer(0); + while (!(readl(ð->ievent) & FEC_IEVENT_MII)) { + if (get_timer(start) > (CONFIG_SYS_HZ / 1000)) { + printf("Write MDIO failed...\n"); + return -1; + } + } + + /* clear MII interrupt bit */ + writel(FEC_IEVENT_MII, ð->ievent); + debug("%s: phy: %02x reg:%02x val:%#x\n", __func__, phyaddr, + regaddr, data); + + return 0; +} + +static int fec_phy_read(struct mii_dev *bus, int phyaddr, int dev_addr, + int regaddr) +{ + return fec_mdio_read(bus->priv, phyaddr, regaddr); +} + +static int fec_phy_write(struct mii_dev *bus, int phyaddr, int dev_addr, + int regaddr, u16 data) +{ + return fec_mdio_write(bus->priv, phyaddr, regaddr, data); +} + +#ifndef CONFIG_PHYLIB +static int miiphy_restart_aneg(struct eth_device *dev) +{ + int ret = 0; +#if !defined(CONFIG_FEC_MXC_NO_ANEG) + struct fec_priv *fec = (struct fec_priv *)dev->priv; + struct ethernet_regs *eth = fec->bus->priv; + + /* + * Wake up from sleep if necessary + * Reset PHY, then delay 300ns + */ +#ifdef CONFIG_MX27 + fec_mdio_write(eth, fec->phy_id, MII_DCOUNTER, 0x00FF); +#endif + fec_mdio_write(eth, fec->phy_id, MII_BMCR, BMCR_RESET); + udelay(1000); + + /* Set the auto-negotiation advertisement register bits */ + fec_mdio_write(eth, fec->phy_id, MII_ADVERTISE, + LPA_100FULL | LPA_100HALF | LPA_10FULL | + LPA_10HALF | PHY_ANLPAR_PSB_802_3); + fec_mdio_write(eth, fec->phy_id, MII_BMCR, + BMCR_ANENABLE | BMCR_ANRESTART); + + if (fec->mii_postcall) + ret = fec->mii_postcall(fec->phy_id); + +#endif + return ret; +} + +#ifndef CONFIG_FEC_FIXED_SPEED +static int miiphy_wait_aneg(struct eth_device *dev) +{ + uint32_t start; + int status; + struct fec_priv *fec = (struct fec_priv *)dev->priv; + struct ethernet_regs *eth = fec->bus->priv; + + /* Wait for AN completion */ + start = get_timer(0); + do { + if (get_timer(start) > (CONFIG_SYS_HZ * 5)) { + printf("%s: Autonegotiation timeout\n", dev->name); + return -1; + } + + status = fec_mdio_read(eth, fec->phy_id, MII_BMSR); + if (status < 0) { + printf("%s: Autonegotiation failed. status: %d\n", + dev->name, status); + return -1; + } + } while (!(status & BMSR_LSTATUS)); + + return 0; +} +#endif /* CONFIG_FEC_FIXED_SPEED */ +#endif + +static int fec_rx_task_enable(struct fec_priv *fec) +{ + writel(FEC_R_DES_ACTIVE_RDAR, &fec->eth->r_des_active); + return 0; +} + +static int fec_rx_task_disable(struct fec_priv *fec) +{ + return 0; +} + +static int fec_tx_task_enable(struct fec_priv *fec) +{ + writel(FEC_X_DES_ACTIVE_TDAR, &fec->eth->x_des_active); + return 0; +} + +static int fec_tx_task_disable(struct fec_priv *fec) +{ + return 0; +} + +/** + * Initialize receive task's buffer descriptors + * @param[in] fec all we know about the device yet + * @param[in] count receive buffer count to be allocated + * @param[in] dsize desired size of each receive buffer + * @return 0 on success + * + * Init all RX descriptors to default values. + */ +static void fec_rbd_init(struct fec_priv *fec, int count, int dsize) +{ + uint32_t size; + ulong data; + int i; + + /* + * Reload the RX descriptors with default values and wipe + * the RX buffers. + */ + size = roundup(dsize, ARCH_DMA_MINALIGN); + for (i = 0; i < count; i++) { + data = fec->rbd_base[i].data_pointer; + memset((void *)data, 0, dsize); + flush_dcache_range(data, data + size); + + fec->rbd_base[i].status = FEC_RBD_EMPTY; + fec->rbd_base[i].data_length = 0; + } + + /* Mark the last RBD to close the ring. */ + fec->rbd_base[i - 1].status = FEC_RBD_WRAP | FEC_RBD_EMPTY; + fec->rbd_index = 0; + + flush_dcache_range((ulong)fec->rbd_base, + (ulong)fec->rbd_base + size); +} + +/** + * Initialize transmit task's buffer descriptors + * @param[in] fec all we know about the device yet + * + * Transmit buffers are created externally. We only have to init the BDs here.\n + * Note: There is a race condition in the hardware. When only one BD is in + * use it must be marked with the WRAP bit to use it for every transmitt. + * This bit in combination with the READY bit results into double transmit + * of each data buffer. It seems the state machine checks READY earlier then + * resetting it after the first transfer. + * Using two BDs solves this issue. + */ +static void fec_tbd_init(struct fec_priv *fec) +{ + ulong addr = (ulong)fec->tbd_base; + unsigned size = roundup(2 * sizeof(struct fec_bd), + ARCH_DMA_MINALIGN); + + memset(fec->tbd_base, 0, size); + fec->tbd_base[0].status = 0; + fec->tbd_base[1].status = FEC_TBD_WRAP; + fec->tbd_index = 0; + flush_dcache_range(addr, addr + size); +} + +/** + * Mark the given read buffer descriptor as free + * @param[in] last 1 if this is the last buffer descriptor in the chain, else 0 + * @param[in] prbd buffer descriptor to mark free again + */ +static void fec_rbd_clean(int last, struct fec_bd *prbd) +{ + unsigned short flags = FEC_RBD_EMPTY; + if (last) + flags |= FEC_RBD_WRAP; + writew(flags, &prbd->status); + writew(0, &prbd->data_length); +} + +static int fec_get_hwaddr(int dev_id, unsigned char *mac) +{ + imx_get_mac_from_fuse(dev_id, mac); + return !is_valid_ethaddr(mac); +} + +#ifdef CONFIG_DM_ETH +static int fecmxc_set_hwaddr(struct udevice *dev) +#else +static int fec_set_hwaddr(struct eth_device *dev) +#endif +{ +#ifdef CONFIG_DM_ETH + struct fec_priv *fec = dev_get_priv(dev); + struct eth_pdata *pdata = dev_get_plat(dev); + uchar *mac = pdata->enetaddr; +#else + uchar *mac = dev->enetaddr; + struct fec_priv *fec = (struct fec_priv *)dev->priv; +#endif + + writel(0, &fec->eth->iaddr1); + writel(0, &fec->eth->iaddr2); + writel(0, &fec->eth->gaddr1); + writel(0, &fec->eth->gaddr2); + + /* Set physical address */ + writel((mac[0] << 24) + (mac[1] << 16) + (mac[2] << 8) + mac[3], + &fec->eth->paddr1); + writel((mac[4] << 24) + (mac[5] << 16) + 0x8808, &fec->eth->paddr2); + + return 0; +} + +/* Do initial configuration of the FEC registers */ +static void fec_reg_setup(struct fec_priv *fec) +{ + uint32_t rcntrl; + + /* Set interrupt mask register */ + writel(0x00000000, &fec->eth->imask); + + /* Clear FEC-Lite interrupt event register(IEVENT) */ + writel(0xffffffff, &fec->eth->ievent); + + /* Set FEC-Lite receive control register(R_CNTRL): */ + + /* Start with frame length = 1518, common for all modes. */ + rcntrl = PKTSIZE << FEC_RCNTRL_MAX_FL_SHIFT; + if (fec->xcv_type != SEVENWIRE) /* xMII modes */ + rcntrl |= FEC_RCNTRL_FCE | FEC_RCNTRL_MII_MODE; + if (fec->xcv_type == RGMII) + rcntrl |= FEC_RCNTRL_RGMII; + else if (fec->xcv_type == RMII) + rcntrl |= FEC_RCNTRL_RMII; + + writel(rcntrl, &fec->eth->r_cntrl); +} + +/** + * Start the FEC engine + * @param[in] dev Our device to handle + */ +#ifdef CONFIG_DM_ETH +static int fec_open(struct udevice *dev) +#else +static int fec_open(struct eth_device *edev) +#endif +{ +#ifdef CONFIG_DM_ETH + struct fec_priv *fec = dev_get_priv(dev); +#else + struct fec_priv *fec = (struct fec_priv *)edev->priv; +#endif + int speed; + ulong addr, size; + int i; + + debug("fec_open: fec_open(dev)\n"); + /* full-duplex, heartbeat disabled */ + writel(1 << 2, &fec->eth->x_cntrl); + fec->rbd_index = 0; + + /* Invalidate all descriptors */ + for (i = 0; i < FEC_RBD_NUM - 1; i++) + fec_rbd_clean(0, &fec->rbd_base[i]); + fec_rbd_clean(1, &fec->rbd_base[i]); + + /* Flush the descriptors into RAM */ + size = roundup(FEC_RBD_NUM * sizeof(struct fec_bd), + ARCH_DMA_MINALIGN); + addr = (ulong)fec->rbd_base; + flush_dcache_range(addr, addr + size); + +#ifdef FEC_QUIRK_ENET_MAC + /* Enable ENET HW endian SWAP */ + writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_DBSWAP, + &fec->eth->ecntrl); + /* Enable ENET store and forward mode */ + writel(readl(&fec->eth->x_wmrk) | FEC_X_WMRK_STRFWD, + &fec->eth->x_wmrk); +#endif + /* Enable FEC-Lite controller */ + writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_ETHER_EN, + &fec->eth->ecntrl); + +#ifdef FEC_ENET_ENABLE_TXC_DELAY + writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_TXC_DLY, + &fec->eth->ecntrl); +#endif + +#ifdef FEC_ENET_ENABLE_RXC_DELAY + writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_RXC_DLY, + &fec->eth->ecntrl); +#endif + +#if defined(CONFIG_MX25) || defined(CONFIG_MX53) || defined(CONFIG_MX6SL) + udelay(100); + + /* setup the MII gasket for RMII mode */ + /* disable the gasket */ + writew(0, &fec->eth->miigsk_enr); + + /* wait for the gasket to be disabled */ + while (readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) + udelay(2); + + /* configure gasket for RMII, 50 MHz, no loopback, and no echo */ + writew(MIIGSK_CFGR_IF_MODE_RMII, &fec->eth->miigsk_cfgr); + + /* re-enable the gasket */ + writew(MIIGSK_ENR_EN, &fec->eth->miigsk_enr); + + /* wait until MII gasket is ready */ + int max_loops = 10; + while ((readw(&fec->eth->miigsk_enr) & MIIGSK_ENR_READY) == 0) { + if (--max_loops <= 0) { + printf("WAIT for MII Gasket ready timed out\n"); + break; + } + } +#endif + +#ifdef CONFIG_PHYLIB + { + /* Start up the PHY */ + int ret = phy_startup(fec->phydev); + + if (ret) { + printf("Could not initialize PHY %s\n", + fec->phydev->dev->name); + return ret; + } + speed = fec->phydev->speed; + } +#elif CONFIG_FEC_FIXED_SPEED + speed = CONFIG_FEC_FIXED_SPEED; +#else + miiphy_wait_aneg(edev); + speed = miiphy_speed(edev->name, fec->phy_id); + miiphy_duplex(edev->name, fec->phy_id); +#endif + +#ifdef FEC_QUIRK_ENET_MAC + { + u32 ecr = readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_SPEED; + u32 rcr = readl(&fec->eth->r_cntrl) & ~FEC_RCNTRL_RMII_10T; + if (speed == _1000BASET) + ecr |= FEC_ECNTRL_SPEED; + else if (speed != _100BASET) + rcr |= FEC_RCNTRL_RMII_10T; + writel(ecr, &fec->eth->ecntrl); + writel(rcr, &fec->eth->r_cntrl); + } +#endif + debug("%s:Speed=%i\n", __func__, speed); + + /* Enable SmartDMA receive task */ + fec_rx_task_enable(fec); + + udelay(100000); + return 0; +} + +#ifdef CONFIG_DM_ETH +static int fecmxc_init(struct udevice *dev) +#else +static int fec_init(struct eth_device *dev, struct bd_info *bd) +#endif +{ +#ifdef CONFIG_DM_ETH + struct fec_priv *fec = dev_get_priv(dev); +#else + struct fec_priv *fec = (struct fec_priv *)dev->priv; +#endif + u8 *mib_ptr = (uint8_t *)&fec->eth->rmon_t_drop; + u8 *i; + ulong addr; + + /* Initialize MAC address */ +#ifdef CONFIG_DM_ETH + fecmxc_set_hwaddr(dev); +#else + fec_set_hwaddr(dev); +#endif + + /* Setup transmit descriptors, there are two in total. */ + fec_tbd_init(fec); + + /* Setup receive descriptors. */ + fec_rbd_init(fec, FEC_RBD_NUM, FEC_MAX_PKT_SIZE); + + fec_reg_setup(fec); + + if (fec->xcv_type != SEVENWIRE) + fec_mii_setspeed(fec->bus->priv); + + /* Set Opcode/Pause Duration Register */ + writel(0x00010020, &fec->eth->op_pause); /* FIXME 0xffff0020; */ + writel(0x2, &fec->eth->x_wmrk); + + /* Set multicast address filter */ + writel(0x00000000, &fec->eth->gaddr1); + writel(0x00000000, &fec->eth->gaddr2); + + /* Do not access reserved register */ + if (!is_mx6ul() && !is_mx6ull() && !is_imx8() && !is_imx8m()) { + /* clear MIB RAM */ + for (i = mib_ptr; i <= mib_ptr + 0xfc; i += 4) + writel(0, i); + + /* FIFO receive start register */ + writel(0x520, &fec->eth->r_fstart); + } + + /* size and address of each buffer */ + writel(FEC_MAX_PKT_SIZE, &fec->eth->emrbr); + + addr = (ulong)fec->tbd_base; + writel((uint32_t)addr, &fec->eth->etdsr); + + addr = (ulong)fec->rbd_base; + writel((uint32_t)addr, &fec->eth->erdsr); + +#ifndef CONFIG_PHYLIB + if (fec->xcv_type != SEVENWIRE) + miiphy_restart_aneg(dev); +#endif + fec_open(dev); + return 0; +} + +/** + * Halt the FEC engine + * @param[in] dev Our device to handle + */ +#ifdef CONFIG_DM_ETH +static void fecmxc_halt(struct udevice *dev) +#else +static void fec_halt(struct eth_device *dev) +#endif +{ +#ifdef CONFIG_DM_ETH + struct fec_priv *fec = dev_get_priv(dev); +#else + struct fec_priv *fec = (struct fec_priv *)dev->priv; +#endif + int counter = 0xffff; + + /* issue graceful stop command to the FEC transmitter if necessary */ + writel(FEC_TCNTRL_GTS | readl(&fec->eth->x_cntrl), + &fec->eth->x_cntrl); + + debug("eth_halt: wait for stop regs\n"); + /* wait for graceful stop to register */ + while ((counter--) && (!(readl(&fec->eth->ievent) & FEC_IEVENT_GRA))) + udelay(1); + + /* Disable SmartDMA tasks */ + fec_tx_task_disable(fec); + fec_rx_task_disable(fec); + + /* + * Disable the Ethernet Controller + * Note: this will also reset the BD index counter! + */ + writel(readl(&fec->eth->ecntrl) & ~FEC_ECNTRL_ETHER_EN, + &fec->eth->ecntrl); + fec->rbd_index = 0; + fec->tbd_index = 0; + debug("eth_halt: done\n"); +} + +/** + * Transmit one frame + * @param[in] dev Our ethernet device to handle + * @param[in] packet Pointer to the data to be transmitted + * @param[in] length Data count in bytes + * @return 0 on success + */ +#ifdef CONFIG_DM_ETH +static int fecmxc_send(struct udevice *dev, void *packet, int length) +#else +static int fec_send(struct eth_device *dev, void *packet, int length) +#endif +{ + unsigned int status; + u32 size; + ulong addr, end; + int timeout = FEC_XFER_TIMEOUT; + int ret = 0; + + /* + * This routine transmits one frame. This routine only accepts + * 6-byte Ethernet addresses. + */ +#ifdef CONFIG_DM_ETH + struct fec_priv *fec = dev_get_priv(dev); +#else + struct fec_priv *fec = (struct fec_priv *)dev->priv; +#endif + + /* + * Check for valid length of data. + */ + if ((length > 1500) || (length <= 0)) { + printf("Payload (%d) too large\n", length); + return -1; + } + + /* + * Setup the transmit buffer. We are always using the first buffer for + * transmission, the second will be empty and only used to stop the DMA + * engine. We also flush the packet to RAM here to avoid cache trouble. + */ +#ifdef CONFIG_FEC_MXC_SWAP_PACKET + swap_packet((uint32_t *)packet, length); +#endif + + addr = (ulong)packet; + end = roundup(addr + length, ARCH_DMA_MINALIGN); + addr &= ~(ARCH_DMA_MINALIGN - 1); + flush_dcache_range(addr, end); + + writew(length, &fec->tbd_base[fec->tbd_index].data_length); + writel((uint32_t)addr, &fec->tbd_base[fec->tbd_index].data_pointer); + + /* + * update BD's status now + * This block: + * - is always the last in a chain (means no chain) + * - should transmitt the CRC + * - might be the last BD in the list, so the address counter should + * wrap (-> keep the WRAP flag) + */ + status = readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_WRAP; + status |= FEC_TBD_LAST | FEC_TBD_TC | FEC_TBD_READY; + writew(status, &fec->tbd_base[fec->tbd_index].status); + + /* + * Flush data cache. This code flushes both TX descriptors to RAM. + * After this code, the descriptors will be safely in RAM and we + * can start DMA. + */ + size = roundup(2 * sizeof(struct fec_bd), ARCH_DMA_MINALIGN); + addr = (ulong)fec->tbd_base; + flush_dcache_range(addr, addr + size); + + /* + * Below we read the DMA descriptor's last four bytes back from the + * DRAM. This is important in order to make sure that all WRITE + * operations on the bus that were triggered by previous cache FLUSH + * have completed. + * + * Otherwise, on MX28, it is possible to observe a corruption of the + * DMA descriptors. Please refer to schematic "Figure 1-2" in MX28RM + * for the bus structure of MX28. The scenario is as follows: + * + * 1) ARM core triggers a series of WRITEs on the AHB_ARB2 bus going + * to DRAM due to flush_dcache_range() + * 2) ARM core writes the FEC registers via AHB_ARB2 + * 3) FEC DMA starts reading/writing from/to DRAM via AHB_ARB3 + * + * Note that 2) does sometimes finish before 1) due to reordering of + * WRITE accesses on the AHB bus, therefore triggering 3) before the + * DMA descriptor is fully written into DRAM. This results in occasional + * corruption of the DMA descriptor. + */ + readl(addr + size - 4); + + /* Enable SmartDMA transmit task */ + fec_tx_task_enable(fec); + + /* + * Wait until frame is sent. On each turn of the wait cycle, we must + * invalidate data cache to see what's really in RAM. Also, we need + * barrier here. + */ + while (--timeout) { + if (!(readl(&fec->eth->x_des_active) & FEC_X_DES_ACTIVE_TDAR)) + break; + } + + if (!timeout) { + ret = -EINVAL; + goto out; + } + + /* + * The TDAR bit is cleared when the descriptors are all out from TX + * but on mx6solox we noticed that the READY bit is still not cleared + * right after TDAR. + * These are two distinct signals, and in IC simulation, we found that + * TDAR always gets cleared prior than the READY bit of last BD becomes + * cleared. + * In mx6solox, we use a later version of FEC IP. It looks like that + * this intrinsic behaviour of TDAR bit has changed in this newer FEC + * version. + * + * Fix this by polling the READY bit of BD after the TDAR polling, + * which covers the mx6solox case and does not harm the other SoCs. + */ + timeout = FEC_XFER_TIMEOUT; + while (--timeout) { + invalidate_dcache_range(addr, addr + size); + if (!(readw(&fec->tbd_base[fec->tbd_index].status) & + FEC_TBD_READY)) + break; + } + + if (!timeout) + ret = -EINVAL; + +out: + debug("fec_send: status 0x%x index %d ret %i\n", + readw(&fec->tbd_base[fec->tbd_index].status), + fec->tbd_index, ret); + /* for next transmission use the other buffer */ + if (fec->tbd_index) + fec->tbd_index = 0; + else + fec->tbd_index = 1; + + return ret; +} + +/** + * Pull one frame from the card + * @param[in] dev Our ethernet device to handle + * @return Length of packet read + */ +#ifdef CONFIG_DM_ETH +static int fecmxc_recv(struct udevice *dev, int flags, uchar **packetp) +#else +static int fec_recv(struct eth_device *dev) +#endif +{ +#ifdef CONFIG_DM_ETH + struct fec_priv *fec = dev_get_priv(dev); +#else + struct fec_priv *fec = (struct fec_priv *)dev->priv; +#endif + struct fec_bd *rbd = &fec->rbd_base[fec->rbd_index]; + unsigned long ievent; + int frame_length, len = 0; + uint16_t bd_status; + ulong addr, size, end; + int i; + +#ifdef CONFIG_DM_ETH + *packetp = memalign(ARCH_DMA_MINALIGN, FEC_MAX_PKT_SIZE); + if (*packetp == 0) { + printf("%s: error allocating packetp\n", __func__); + return -ENOMEM; + } +#else + ALLOC_CACHE_ALIGN_BUFFER(uchar, buff, FEC_MAX_PKT_SIZE); +#endif + + /* Check if any critical events have happened */ + ievent = readl(&fec->eth->ievent); + writel(ievent, &fec->eth->ievent); + debug("fec_recv: ievent 0x%lx\n", ievent); + if (ievent & FEC_IEVENT_BABR) { +#ifdef CONFIG_DM_ETH + fecmxc_halt(dev); + fecmxc_init(dev); +#else + fec_halt(dev); + fec_init(dev, fec->bd); +#endif + printf("some error: 0x%08lx\n", ievent); + return 0; + } + if (ievent & FEC_IEVENT_HBERR) { + /* Heartbeat error */ + writel(0x00000001 | readl(&fec->eth->x_cntrl), + &fec->eth->x_cntrl); + } + if (ievent & FEC_IEVENT_GRA) { + /* Graceful stop complete */ + if (readl(&fec->eth->x_cntrl) & 0x00000001) { +#ifdef CONFIG_DM_ETH + fecmxc_halt(dev); +#else + fec_halt(dev); +#endif + writel(~0x00000001 & readl(&fec->eth->x_cntrl), + &fec->eth->x_cntrl); +#ifdef CONFIG_DM_ETH + fecmxc_init(dev); +#else + fec_init(dev, fec->bd); +#endif + } + } + + /* + * Read the buffer status. Before the status can be read, the data cache + * must be invalidated, because the data in RAM might have been changed + * by DMA. The descriptors are properly aligned to cachelines so there's + * no need to worry they'd overlap. + * + * WARNING: By invalidating the descriptor here, we also invalidate + * the descriptors surrounding this one. Therefore we can NOT change the + * contents of this descriptor nor the surrounding ones. The problem is + * that in order to mark the descriptor as processed, we need to change + * the descriptor. The solution is to mark the whole cache line when all + * descriptors in the cache line are processed. + */ + addr = (ulong)rbd; + addr &= ~(ARCH_DMA_MINALIGN - 1); + size = roundup(sizeof(struct fec_bd), ARCH_DMA_MINALIGN); + invalidate_dcache_range(addr, addr + size); + + bd_status = readw(&rbd->status); + debug("fec_recv: status 0x%x\n", bd_status); + + if (!(bd_status & FEC_RBD_EMPTY)) { + if ((bd_status & FEC_RBD_LAST) && !(bd_status & FEC_RBD_ERR) && + ((readw(&rbd->data_length) - 4) > 14)) { + /* Get buffer address and size */ + addr = readl(&rbd->data_pointer); + frame_length = readw(&rbd->data_length) - 4; + /* Invalidate data cache over the buffer */ + end = roundup(addr + frame_length, ARCH_DMA_MINALIGN); + addr &= ~(ARCH_DMA_MINALIGN - 1); + invalidate_dcache_range(addr, end); + + /* Fill the buffer and pass it to upper layers */ +#ifdef CONFIG_FEC_MXC_SWAP_PACKET + swap_packet((uint32_t *)addr, frame_length); +#endif + +#ifdef CONFIG_DM_ETH + memcpy(*packetp, (char *)addr, frame_length); +#else + memcpy(buff, (char *)addr, frame_length); + net_process_received_packet(buff, frame_length); +#endif + len = frame_length; + } else { + if (bd_status & FEC_RBD_ERR) + debug("error frame: 0x%08lx 0x%08x\n", + addr, bd_status); + } + + /* + * Free the current buffer, restart the engine and move forward + * to the next buffer. Here we check if the whole cacheline of + * descriptors was already processed and if so, we mark it free + * as whole. + */ + size = RXDESC_PER_CACHELINE - 1; + if ((fec->rbd_index & size) == size) { + i = fec->rbd_index - size; + addr = (ulong)&fec->rbd_base[i]; + for (; i <= fec->rbd_index ; i++) { + fec_rbd_clean(i == (FEC_RBD_NUM - 1), + &fec->rbd_base[i]); + } + flush_dcache_range(addr, + addr + ARCH_DMA_MINALIGN); + } + + fec_rx_task_enable(fec); + fec->rbd_index = (fec->rbd_index + 1) % FEC_RBD_NUM; + } + debug("fec_recv: stop\n"); + + return len; +} + +static void fec_set_dev_name(char *dest, int dev_id) +{ + sprintf(dest, (dev_id == -1) ? "FEC" : "FEC%i", dev_id); +} + +static int fec_alloc_descs(struct fec_priv *fec) +{ + unsigned int size; + int i; + uint8_t *data; + ulong addr; + + /* Allocate TX descriptors. */ + size = roundup(2 * sizeof(struct fec_bd), ARCH_DMA_MINALIGN); + fec->tbd_base = memalign(ARCH_DMA_MINALIGN, size); + if (!fec->tbd_base) + goto err_tx; + + /* Allocate RX descriptors. */ + size = roundup(FEC_RBD_NUM * sizeof(struct fec_bd), ARCH_DMA_MINALIGN); + fec->rbd_base = memalign(ARCH_DMA_MINALIGN, size); + if (!fec->rbd_base) + goto err_rx; + + memset(fec->rbd_base, 0, size); + + /* Allocate RX buffers. */ + + /* Maximum RX buffer size. */ + size = roundup(FEC_MAX_PKT_SIZE, FEC_DMA_RX_MINALIGN); + for (i = 0; i < FEC_RBD_NUM; i++) { + data = memalign(FEC_DMA_RX_MINALIGN, size); + if (!data) { + printf("%s: error allocating rxbuf %d\n", __func__, i); + goto err_ring; + } + + memset(data, 0, size); + + addr = (ulong)data; + fec->rbd_base[i].data_pointer = (uint32_t)addr; + fec->rbd_base[i].status = FEC_RBD_EMPTY; + fec->rbd_base[i].data_length = 0; + /* Flush the buffer to memory. */ + flush_dcache_range(addr, addr + size); + } + + /* Mark the last RBD to close the ring. */ + fec->rbd_base[i - 1].status = FEC_RBD_WRAP | FEC_RBD_EMPTY; + + fec->rbd_index = 0; + fec->tbd_index = 0; + + return 0; + +err_ring: + for (; i >= 0; i--) { + addr = fec->rbd_base[i].data_pointer; + free((void *)addr); + } + free(fec->rbd_base); +err_rx: + free(fec->tbd_base); +err_tx: + return -ENOMEM; +} + +static void fec_free_descs(struct fec_priv *fec) +{ + int i; + ulong addr; + + for (i = 0; i < FEC_RBD_NUM; i++) { + addr = fec->rbd_base[i].data_pointer; + free((void *)addr); + } + free(fec->rbd_base); + free(fec->tbd_base); +} + +struct mii_dev *fec_get_miibus(ulong base_addr, int dev_id) +{ + struct ethernet_regs *eth = (struct ethernet_regs *)base_addr; + struct mii_dev *bus; + int ret; + + bus = mdio_alloc(); + if (!bus) { + printf("mdio_alloc failed\n"); + return NULL; + } + bus->read = fec_phy_read; + bus->write = fec_phy_write; + bus->priv = eth; + fec_set_dev_name(bus->name, dev_id); + + ret = mdio_register(bus); + if (ret) { + printf("mdio_register failed\n"); + free(bus); + return NULL; + } + fec_mii_setspeed(eth); + return bus; +} + +#ifndef CONFIG_DM_ETH +#ifdef CONFIG_PHYLIB +int fec_probe(struct bd_info *bd, int dev_id, uint32_t base_addr, + struct mii_dev *bus, struct phy_device *phydev) +#else +static int fec_probe(struct bd_info *bd, int dev_id, uint32_t base_addr, + struct mii_dev *bus, int phy_id) +#endif +{ + struct eth_device *edev; + struct fec_priv *fec; + unsigned char ethaddr[6]; + char mac[16]; + uint32_t start; + int ret = 0; + + /* create and fill edev struct */ + edev = (struct eth_device *)malloc(sizeof(struct eth_device)); + if (!edev) { + puts("fec_mxc: not enough malloc memory for eth_device\n"); + ret = -ENOMEM; + goto err1; + } + + fec = (struct fec_priv *)malloc(sizeof(struct fec_priv)); + if (!fec) { + puts("fec_mxc: not enough malloc memory for fec_priv\n"); + ret = -ENOMEM; + goto err2; + } + + memset(edev, 0, sizeof(*edev)); + memset(fec, 0, sizeof(*fec)); + + ret = fec_alloc_descs(fec); + if (ret) + goto err3; + + edev->priv = fec; + edev->init = fec_init; + edev->send = fec_send; + edev->recv = fec_recv; + edev->halt = fec_halt; + edev->write_hwaddr = fec_set_hwaddr; + + fec->eth = (struct ethernet_regs *)(ulong)base_addr; + fec->bd = bd; + + fec->xcv_type = CONFIG_FEC_XCV_TYPE; + + /* Reset chip. */ + writel(readl(&fec->eth->ecntrl) | FEC_ECNTRL_RESET, &fec->eth->ecntrl); + start = get_timer(0); + while (readl(&fec->eth->ecntrl) & FEC_ECNTRL_RESET) { + if (get_timer(start) > (CONFIG_SYS_HZ * 5)) { + printf("FEC MXC: Timeout resetting chip\n"); + goto err4; + } + udelay(10); + } + + fec_reg_setup(fec); + fec_set_dev_name(edev->name, dev_id); + fec->dev_id = (dev_id == -1) ? 0 : dev_id; + fec->bus = bus; + fec_mii_setspeed(bus->priv); +#ifdef CONFIG_PHYLIB + fec->phydev = phydev; + phy_connect_dev(phydev, edev); + /* Configure phy */ + phy_config(phydev); +#else + fec->phy_id = phy_id; +#endif + eth_register(edev); + /* only support one eth device, the index number pointed by dev_id */ + edev->index = fec->dev_id; + + if (fec_get_hwaddr(fec->dev_id, ethaddr) == 0) { + debug("got MAC%d address from fuse: %pM\n", fec->dev_id, ethaddr); + memcpy(edev->enetaddr, ethaddr, 6); + if (fec->dev_id) + sprintf(mac, "eth%daddr", fec->dev_id); + else + strcpy(mac, "ethaddr"); + if (!env_get(mac)) + eth_env_set_enetaddr(mac, ethaddr); + } + return ret; +err4: + fec_free_descs(fec); +err3: + free(fec); +err2: + free(edev); +err1: + return ret; +} + +int fecmxc_initialize_multi(struct bd_info *bd, int dev_id, int phy_id, + uint32_t addr) +{ + uint32_t base_mii; + struct mii_dev *bus = NULL; +#ifdef CONFIG_PHYLIB + struct phy_device *phydev = NULL; +#endif + int ret; + + if (CONFIG_IS_ENABLED(IMX_MODULE_FUSE)) { + if (enet_fused((ulong)addr)) { + printf("SoC fuse indicates Ethernet@0x%x is unavailable.\n", addr); + return -ENODEV; + } + } + +#ifdef CONFIG_FEC_MXC_MDIO_BASE + /* + * The i.MX28 has two ethernet interfaces, but they are not equal. + * Only the first one can access the MDIO bus. + */ + base_mii = CONFIG_FEC_MXC_MDIO_BASE; +#else + base_mii = addr; +#endif + debug("eth_init: fec_probe(bd, %i, %i) @ %08x\n", dev_id, phy_id, addr); + bus = fec_get_miibus(base_mii, dev_id); + if (!bus) + return -ENOMEM; +#ifdef CONFIG_PHYLIB + phydev = phy_find_by_mask(bus, 1 << phy_id, PHY_INTERFACE_MODE_RGMII); + if (!phydev) { + mdio_unregister(bus); + free(bus); + return -ENOMEM; + } + ret = fec_probe(bd, dev_id, addr, bus, phydev); +#else + ret = fec_probe(bd, dev_id, addr, bus, phy_id); +#endif + if (ret) { +#ifdef CONFIG_PHYLIB + free(phydev); +#endif + mdio_unregister(bus); + free(bus); + } + return ret; +} + +#ifdef CONFIG_FEC_MXC_PHYADDR +int fecmxc_initialize(struct bd_info *bd) +{ + return fecmxc_initialize_multi(bd, -1, CONFIG_FEC_MXC_PHYADDR, + IMX_FEC_BASE); +} +#endif + +#ifndef CONFIG_PHYLIB +int fecmxc_register_mii_postcall(struct eth_device *dev, int (*cb)(int)) +{ + struct fec_priv *fec = (struct fec_priv *)dev->priv; + fec->mii_postcall = cb; + return 0; +} +#endif + +#else + +static int fecmxc_read_rom_hwaddr(struct udevice *dev) +{ + struct fec_priv *priv = dev_get_priv(dev); + struct eth_pdata *pdata = dev_get_plat(dev); + + return fec_get_hwaddr(priv->dev_id, pdata->enetaddr); +} + +static int fecmxc_free_pkt(struct udevice *dev, uchar *packet, int length) +{ + if (packet) + free(packet); + + return 0; +} + +static const struct eth_ops fecmxc_ops = { + .start = fecmxc_init, + .send = fecmxc_send, + .recv = fecmxc_recv, + .free_pkt = fecmxc_free_pkt, + .stop = fecmxc_halt, + .write_hwaddr = fecmxc_set_hwaddr, + .read_rom_hwaddr = fecmxc_read_rom_hwaddr, +}; + +static int device_get_phy_addr(struct fec_priv *priv, struct udevice *dev) +{ + struct ofnode_phandle_args phandle_args; + int reg, ret; + + ret = dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0, + &phandle_args); + if (ret) { + debug("Failed to find phy-handle (err = %d\n)", ret); + return ret; + } + + if (!ofnode_is_available(phandle_args.node)) + return -ENOENT; + + priv->phy_of_node = phandle_args.node; + reg = ofnode_read_u32_default(phandle_args.node, "reg", 0); + + return reg; +} + +static int fec_phy_init(struct fec_priv *priv, struct udevice *dev) +{ + struct phy_device *phydev; + int addr; + + addr = device_get_phy_addr(priv, dev); +#ifdef CONFIG_FEC_MXC_PHYADDR + addr = CONFIG_FEC_MXC_PHYADDR; +#endif + + phydev = phy_connect(priv->bus, addr, dev, priv->interface); + if (!phydev) + return -ENODEV; + + priv->phydev = phydev; + priv->phydev->node = priv->phy_of_node; + phy_config(phydev); + + return 0; +} + +#if CONFIG_IS_ENABLED(DM_GPIO) +/* FEC GPIO reset */ +static void fec_gpio_reset(struct fec_priv *priv) +{ + debug("fec_gpio_reset: fec_gpio_reset(dev)\n"); + if (dm_gpio_is_valid(&priv->phy_reset_gpio)) { + dm_gpio_set_value(&priv->phy_reset_gpio, 1); + mdelay(priv->reset_delay); + dm_gpio_set_value(&priv->phy_reset_gpio, 0); + if (priv->reset_post_delay) + mdelay(priv->reset_post_delay); + } +} +#endif + +static int fecmxc_probe(struct udevice *dev) +{ + bool dm_mii_bus = true; + struct eth_pdata *pdata = dev_get_plat(dev); + struct fec_priv *priv = dev_get_priv(dev); + struct mii_dev *bus = NULL; + uint32_t start; + int ret; + + if (CONFIG_IS_ENABLED(IMX_MODULE_FUSE)) { + if (enet_fused((ulong)priv->eth)) { + printf("SoC fuse indicates Ethernet@0x%lx is unavailable.\n", (ulong)priv->eth); + return -ENODEV; + } + } + + if (IS_ENABLED(CONFIG_IMX8)) { + ret = clk_get_by_name(dev, "ipg", &priv->ipg_clk); + if (ret < 0) { + debug("Can't get FEC ipg clk: %d\n", ret); + return ret; + } + ret = clk_enable(&priv->ipg_clk); + if (ret < 0) { + debug("Can't enable FEC ipg clk: %d\n", ret); + return ret; + } + + priv->clk_rate = clk_get_rate(&priv->ipg_clk); + } else if (CONFIG_IS_ENABLED(CLK_CCF)) { + ret = clk_get_by_name(dev, "ipg", &priv->ipg_clk); + if (ret < 0) { + debug("Can't get FEC ipg clk: %d\n", ret); + return ret; + } + ret = clk_enable(&priv->ipg_clk); + if(ret) + return ret; + + ret = clk_get_by_name(dev, "ahb", &priv->ahb_clk); + if (ret < 0) { + debug("Can't get FEC ahb clk: %d\n", ret); + return ret; + } + ret = clk_enable(&priv->ahb_clk); + if (ret) + return ret; + + ret = clk_get_by_name(dev, "enet_out", &priv->clk_enet_out); + if (!ret) { + ret = clk_enable(&priv->clk_enet_out); + if (ret) + return ret; + } + + ret = clk_get_by_name(dev, "enet_clk_ref", &priv->clk_ref); + if (!ret) { + ret = clk_enable(&priv->clk_ref); + if (ret) + return ret; + } + + ret = clk_get_by_name(dev, "ptp", &priv->clk_ptp); + if (!ret) { + ret = clk_enable(&priv->clk_ptp); + if (ret) + return ret; + } + + priv->clk_rate = clk_get_rate(&priv->ipg_clk); + } + + ret = fec_alloc_descs(priv); + if (ret) + return ret; + +#ifdef CONFIG_DM_REGULATOR + if (priv->phy_supply) { + ret = regulator_set_enable(priv->phy_supply, true); + if (ret) { + printf("%s: Error enabling phy supply\n", dev->name); + return ret; + } + } +#endif + +#if CONFIG_IS_ENABLED(DM_GPIO) + fec_gpio_reset(priv); +#endif + /* Reset chip. */ + writel(readl(&priv->eth->ecntrl) | FEC_ECNTRL_RESET, + &priv->eth->ecntrl); + start = get_timer(0); + while (readl(&priv->eth->ecntrl) & FEC_ECNTRL_RESET) { + if (get_timer(start) > (CONFIG_SYS_HZ * 5)) { + printf("FEC MXC: Timeout reseting chip\n"); + goto err_timeout; + } + udelay(10); + } + + fec_reg_setup(priv); + + priv->dev_id = dev_seq(dev); + +#ifdef CONFIG_DM_ETH_PHY + bus = eth_phy_get_mdio_bus(dev); +#endif + + if (!bus) { + dm_mii_bus = false; +#ifdef CONFIG_FEC_MXC_MDIO_BASE + bus = fec_get_miibus((ulong)CONFIG_FEC_MXC_MDIO_BASE, + dev_seq(dev)); +#else + bus = fec_get_miibus((ulong)priv->eth, dev_seq(dev)); +#endif + } + if (!bus) { + ret = -ENOMEM; + goto err_mii; + } + +#ifdef CONFIG_DM_ETH_PHY + eth_phy_set_mdio_bus(dev, bus); +#endif + + priv->bus = bus; + priv->interface = pdata->phy_interface; + switch (priv->interface) { + case PHY_INTERFACE_MODE_MII: + priv->xcv_type = MII100; + break; + case PHY_INTERFACE_MODE_RMII: + priv->xcv_type = RMII; + break; + case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_ID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_TXID: + priv->xcv_type = RGMII; + break; + default: + priv->xcv_type = CONFIG_FEC_XCV_TYPE; + printf("Unsupported interface type %d defaulting to %d\n", + priv->interface, priv->xcv_type); + break; + } + + ret = fec_phy_init(priv, dev); + if (ret) + goto err_phy; + + return 0; + +err_phy: + if (!dm_mii_bus) { + mdio_unregister(bus); + free(bus); + } +err_mii: +err_timeout: + fec_free_descs(priv); + return ret; +} + +static int fecmxc_remove(struct udevice *dev) +{ + struct fec_priv *priv = dev_get_priv(dev); + + free(priv->phydev); + fec_free_descs(priv); + mdio_unregister(priv->bus); + mdio_free(priv->bus); + +#ifdef CONFIG_DM_REGULATOR + if (priv->phy_supply) + regulator_set_enable(priv->phy_supply, false); +#endif + + return 0; +} + +static int fecmxc_of_to_plat(struct udevice *dev) +{ + int ret = 0; + struct eth_pdata *pdata = dev_get_plat(dev); + struct fec_priv *priv = dev_get_priv(dev); + const char *phy_mode; + + pdata->iobase = dev_read_addr(dev); + priv->eth = (struct ethernet_regs *)pdata->iobase; + + pdata->phy_interface = -1; + phy_mode = fdt_getprop(gd->fdt_blob, dev_of_offset(dev), "phy-mode", + NULL); + if (phy_mode) + pdata->phy_interface = phy_get_interface_by_name(phy_mode); + if (pdata->phy_interface == -1) { + debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); + return -EINVAL; + } + +#ifdef CONFIG_DM_REGULATOR + device_get_supply_regulator(dev, "phy-supply", &priv->phy_supply); +#endif + +#if CONFIG_IS_ENABLED(DM_GPIO) + ret = gpio_request_by_name(dev, "phy-reset-gpios", 0, + &priv->phy_reset_gpio, GPIOD_IS_OUT); + if (ret < 0) + return 0; /* property is optional, don't return error! */ + + priv->reset_delay = dev_read_u32_default(dev, "phy-reset-duration", 1); + if (priv->reset_delay > 1000) { + printf("FEC MXC: phy reset duration should be <= 1000ms\n"); + /* property value wrong, use default value */ + priv->reset_delay = 1; + } + + priv->reset_post_delay = dev_read_u32_default(dev, + "phy-reset-post-delay", + 0); + if (priv->reset_post_delay > 1000) { + printf("FEC MXC: phy reset post delay should be <= 1000ms\n"); + /* property value wrong, use default value */ + priv->reset_post_delay = 0; + } +#endif + + return 0; +} + +static const struct udevice_id fecmxc_ids[] = { + { .compatible = "fsl,imx28-fec" }, + { .compatible = "fsl,imx6q-fec" }, + { .compatible = "fsl,imx6sl-fec" }, + { .compatible = "fsl,imx6sx-fec" }, + { .compatible = "fsl,imx6ul-fec" }, + { .compatible = "fsl,imx53-fec" }, + { .compatible = "fsl,imx7d-fec" }, + { .compatible = "fsl,mvf600-fec" }, + { } +}; + +U_BOOT_DRIVER(fecmxc_gem) = { + .name = "fecmxc", + .id = UCLASS_ETH, + .of_match = fecmxc_ids, + .of_to_plat = fecmxc_of_to_plat, + .probe = fecmxc_probe, + .remove = fecmxc_remove, + .ops = &fecmxc_ops, + .priv_auto = sizeof(struct fec_priv), + .plat_auto = sizeof(struct eth_pdata), +}; +#endif |