1 files changed, 362 insertions, 0 deletions
diff --git a/roms/u-boot/drivers/spi/cadence_qspi.c b/roms/u-boot/drivers/spi/cadence_qspi.c
new file mode 100644
index 000000000..67980431b
--- /dev/null
+++ b/roms/u-boot/drivers/spi/cadence_qspi.c
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2012
+ * Altera Corporation <www.altera.com>
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <log.h>
+#include <asm-generic/io.h>
+#include <dm.h>
+#include <fdtdec.h>
+#include <malloc.h>
+#include <reset.h>
+#include <spi.h>
+#include <spi-mem.h>
+#include <dm/device_compat.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/sizes.h>
+#include "cadence_qspi.h"
+
+#define CQSPI_STIG_READ			0
+#define CQSPI_STIG_WRITE		1
+#define CQSPI_READ			2
+#define CQSPI_WRITE			3
+
+static int cadence_spi_write_speed(struct udevice *bus, uint hz)
+{
+	struct cadence_spi_plat *plat = dev_get_plat(bus);
+	struct cadence_spi_priv *priv = dev_get_priv(bus);
+
+	cadence_qspi_apb_config_baudrate_div(priv->regbase,
+					     plat->ref_clk_hz, hz);
+
+	/* Reconfigure delay timing if speed is changed. */
+	cadence_qspi_apb_delay(priv->regbase, plat->ref_clk_hz, hz,
+			       plat->tshsl_ns, plat->tsd2d_ns,
+			       plat->tchsh_ns, plat->tslch_ns);
+
+	return 0;
+}
+
+static int cadence_spi_read_id(void *reg_base, u8 len, u8 *idcode)
+{
+	struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(0x9F, 1),
+					  SPI_MEM_OP_NO_ADDR,
+					  SPI_MEM_OP_NO_DUMMY,
+					  SPI_MEM_OP_DATA_IN(len, idcode, 1));
+
+	return cadence_qspi_apb_command_read(reg_base, &op);
+}
+
+/* Calibration sequence to determine the read data capture delay register */
+static int spi_calibration(struct udevice *bus, uint hz)
+{
+	struct cadence_spi_priv *priv = dev_get_priv(bus);
+	void *base = priv->regbase;
+	unsigned int idcode = 0, temp = 0;
+	int err = 0, i, range_lo = -1, range_hi = -1;
+
+	/* start with slowest clock (1 MHz) */
+	cadence_spi_write_speed(bus, 1000000);
+
+	/* configure the read data capture delay register to 0 */
+	cadence_qspi_apb_readdata_capture(base, 1, 0);
+
+	/* Enable QSPI */
+	cadence_qspi_apb_controller_enable(base);
+
+	/* read the ID which will be our golden value */
+	err = cadence_spi_read_id(base, 3, (u8 *)&idcode);
+	if (err) {
+		puts("SF: Calibration failed (read)\n");
+		return err;
+	}
+
+	/* use back the intended clock and find low range */
+	cadence_spi_write_speed(bus, hz);
+	for (i = 0; i < CQSPI_READ_CAPTURE_MAX_DELAY; i++) {
+		/* Disable QSPI */
+		cadence_qspi_apb_controller_disable(base);
+
+		/* reconfigure the read data capture delay register */
+		cadence_qspi_apb_readdata_capture(base, 1, i);
+
+		/* Enable back QSPI */
+		cadence_qspi_apb_controller_enable(base);
+
+		/* issue a RDID to get the ID value */
+		err = cadence_spi_read_id(base, 3, (u8 *)&temp);
+		if (err) {
+			puts("SF: Calibration failed (read)\n");
+			return err;
+		}
+
+		/* search for range lo */
+		if (range_lo == -1 && temp == idcode) {
+			range_lo = i;
+			continue;
+		}
+
+		/* search for range hi */
+		if (range_lo != -1 && temp != idcode) {
+			range_hi = i - 1;
+			break;
+		}
+		range_hi = i;
+	}
+
+	if (range_lo == -1) {
+		puts("SF: Calibration failed (low range)\n");
+		return err;
+	}
+
+	/* Disable QSPI for subsequent initialization */
+	cadence_qspi_apb_controller_disable(base);
+
+	/* configure the final value for read data capture delay register */
+	cadence_qspi_apb_readdata_capture(base, 1, (range_hi + range_lo) / 2);
+	debug("SF: Read data capture delay calibrated to %i (%i - %i)\n",
+	      (range_hi + range_lo) / 2, range_lo, range_hi);
+
+	/* just to ensure we do once only when speed or chip select change */
+	priv->qspi_calibrated_hz = hz;
+	priv->qspi_calibrated_cs = spi_chip_select(bus);
+
+	return 0;
+}
+
+static int cadence_spi_set_speed(struct udevice *bus, uint hz)
+{
+	struct cadence_spi_plat *plat = dev_get_plat(bus);
+	struct cadence_spi_priv *priv = dev_get_priv(bus);
+	int err;
+
+	if (hz > plat->max_hz)
+		hz = plat->max_hz;
+
+	/* Disable QSPI */
+	cadence_qspi_apb_controller_disable(priv->regbase);
+
+	/*
+	 * Calibration required for different current SCLK speed, requested
+	 * SCLK speed or chip select
+	 */
+	if (priv->previous_hz != hz ||
+	    priv->qspi_calibrated_hz != hz ||
+	    priv->qspi_calibrated_cs != spi_chip_select(bus)) {
+		err = spi_calibration(bus, hz);
+		if (err)
+			return err;
+
+		/* prevent calibration run when same as previous request */
+		priv->previous_hz = hz;
+	}
+
+	/* Enable QSPI */
+	cadence_qspi_apb_controller_enable(priv->regbase);
+
+	debug("%s: speed=%d\n", __func__, hz);
+
+	return 0;
+}
+
+static int cadence_spi_probe(struct udevice *bus)
+{
+	struct cadence_spi_plat *plat = dev_get_plat(bus);
+	struct cadence_spi_priv *priv = dev_get_priv(bus);
+	struct clk clk;
+	int ret;
+
+	priv->regbase = plat->regbase;
+	priv->ahbbase = plat->ahbbase;
+
+	if (plat->ref_clk_hz == 0) {
+		ret = clk_get_by_index(bus, 0, &clk);
+		if (ret) {
+#ifdef CONFIG_CQSPI_REF_CLK
+			plat->ref_clk_hz = CONFIG_CQSPI_REF_CLK;
+#else
+			return ret;
+#endif
+		} else {
+			plat->ref_clk_hz = clk_get_rate(&clk);
+			clk_free(&clk);
+			if (IS_ERR_VALUE(plat->ref_clk_hz))
+				return plat->ref_clk_hz;
+		}
+	}
+
+	ret = reset_get_bulk(bus, &priv->resets);
+	if (ret)
+		dev_warn(bus, "Can't get reset: %d\n", ret);
+	else
+		reset_deassert_bulk(&priv->resets);
+
+	if (!priv->qspi_is_init) {
+		cadence_qspi_apb_controller_init(plat);
+		priv->qspi_is_init = 1;
+	}
+
+	return 0;
+}
+
+static int cadence_spi_remove(struct udevice *dev)
+{
+	struct cadence_spi_priv *priv = dev_get_priv(dev);
+
+	return reset_release_bulk(&priv->resets);
+}
+
+static int cadence_spi_set_mode(struct udevice *bus, uint mode)
+{
+	struct cadence_spi_plat *plat = dev_get_plat(bus);
+	struct cadence_spi_priv *priv = dev_get_priv(bus);
+
+	/* Disable QSPI */
+	cadence_qspi_apb_controller_disable(priv->regbase);
+
+	/* Set SPI mode */
+	cadence_qspi_apb_set_clk_mode(priv->regbase, mode);
+
+	/* Enable Direct Access Controller */
+	if (plat->use_dac_mode)
+		cadence_qspi_apb_dac_mode_enable(priv->regbase);
+
+	/* Enable QSPI */
+	cadence_qspi_apb_controller_enable(priv->regbase);
+
+	return 0;
+}
+
+static int cadence_spi_mem_exec_op(struct spi_slave *spi,
+				   const struct spi_mem_op *op)
+{
+	struct udevice *bus = spi->dev->parent;
+	struct cadence_spi_plat *plat = dev_get_plat(bus);
+	struct cadence_spi_priv *priv = dev_get_priv(bus);
+	void *base = priv->regbase;
+	int err = 0;
+	u32 mode;
+
+	/* Set Chip select */
+	cadence_qspi_apb_chipselect(base, spi_chip_select(spi->dev),
+				    plat->is_decoded_cs);
+
+	if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) {
+		if (!op->addr.nbytes)
+			mode = CQSPI_STIG_READ;
+		else
+			mode = CQSPI_READ;
+	} else {
+		if (!op->addr.nbytes || !op->data.buf.out)
+			mode = CQSPI_STIG_WRITE;
+		else
+			mode = CQSPI_WRITE;
+	}
+
+	switch (mode) {
+	case CQSPI_STIG_READ:
+		err = cadence_qspi_apb_command_read(base, op);
+		break;
+	case CQSPI_STIG_WRITE:
+		err = cadence_qspi_apb_command_write(base, op);
+		break;
+	case CQSPI_READ:
+		err = cadence_qspi_apb_read_setup(plat, op);
+		if (!err)
+			err = cadence_qspi_apb_read_execute(plat, op);
+		break;
+	case CQSPI_WRITE:
+		err = cadence_qspi_apb_write_setup(plat, op);
+		if (!err)
+			err = cadence_qspi_apb_write_execute(plat, op);
+		break;
+	default:
+		err = -1;
+		break;
+	}
+
+	return err;
+}
+
+static int cadence_spi_of_to_plat(struct udevice *bus)
+{
+	struct cadence_spi_plat *plat = dev_get_plat(bus);
+	ofnode subnode;
+
+	plat->regbase = (void *)devfdt_get_addr_index(bus, 0);
+	plat->ahbbase = (void *)devfdt_get_addr_size_index(bus, 1,
+			&plat->ahbsize);
+	plat->is_decoded_cs = dev_read_bool(bus, "cdns,is-decoded-cs");
+	plat->fifo_depth = dev_read_u32_default(bus, "cdns,fifo-depth", 128);
+	plat->fifo_width = dev_read_u32_default(bus, "cdns,fifo-width", 4);
+	plat->trigger_address = dev_read_u32_default(bus,
+						     "cdns,trigger-address",
+						     0);
+	/* Use DAC mode only when MMIO window is at least 8M wide */
+	if (plat->ahbsize >= SZ_8M)
+		plat->use_dac_mode = true;
+
+	/* All other paramters are embedded in the child node */
+	subnode = dev_read_first_subnode(bus);
+	if (!ofnode_valid(subnode)) {
+		printf("Error: subnode with SPI flash config missing!\n");
+		return -ENODEV;
+	}
+
+	/* Use 500 KHz as a suitable default */
+	plat->max_hz = ofnode_read_u32_default(subnode, "spi-max-frequency",
+					       500000);
+
+	/* Read other parameters from DT */
+	plat->page_size = ofnode_read_u32_default(subnode, "page-size", 256);
+	plat->block_size = ofnode_read_u32_default(subnode, "block-size", 16);
+	plat->tshsl_ns = ofnode_read_u32_default(subnode, "cdns,tshsl-ns",
+						 200);
+	plat->tsd2d_ns = ofnode_read_u32_default(subnode, "cdns,tsd2d-ns",
+						 255);
+	plat->tchsh_ns = ofnode_read_u32_default(subnode, "cdns,tchsh-ns", 20);
+	plat->tslch_ns = ofnode_read_u32_default(subnode, "cdns,tslch-ns", 20);
+
+	debug("%s: regbase=%p ahbbase=%p max-frequency=%d page-size=%d\n",
+	      __func__, plat->regbase, plat->ahbbase, plat->max_hz,
+	      plat->page_size);
+
+	return 0;
+}
+
+static const struct spi_controller_mem_ops cadence_spi_mem_ops = {
+	.exec_op = cadence_spi_mem_exec_op,
+};
+
+static const struct dm_spi_ops cadence_spi_ops = {
+	.set_speed	= cadence_spi_set_speed,
+	.set_mode	= cadence_spi_set_mode,
+	.mem_ops	= &cadence_spi_mem_ops,
+	/*
+	 * cs_info is not needed, since we require all chip selects to be
+	 * in the device tree explicitly
+	 */
+};
+
+static const struct udevice_id cadence_spi_ids[] = {
+	{ .compatible = "cdns,qspi-nor" },
+	{ .compatible = "ti,am654-ospi" },
+	{ }
+};
+
+U_BOOT_DRIVER(cadence_spi) = {
+	.name = "cadence_spi",
+	.id = UCLASS_SPI,
+	.of_match = cadence_spi_ids,
+	.ops = &cadence_spi_ops,
+	.of_to_plat = cadence_spi_of_to_plat,
+	.plat_auto	= sizeof(struct cadence_spi_plat),
+	.priv_auto	= sizeof(struct cadence_spi_priv),
+	.probe = cadence_spi_probe,
+	.remove = cadence_spi_remove,
+	.flags = DM_FLAG_OS_PREPARE,
+};