diff options
Diffstat (limited to 'roms/u-boot/include/configs/M54418TWR.h')
| -rw-r--r-- | roms/u-boot/include/configs/M54418TWR.h | 283 |
1 files changed, 283 insertions, 0 deletions
diff --git a/roms/u-boot/include/configs/M54418TWR.h b/roms/u-boot/include/configs/M54418TWR.h new file mode 100644 index 000000000..5447f84ca --- /dev/null +++ b/roms/u-boot/include/configs/M54418TWR.h @@ -0,0 +1,283 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Configuation settings for the Freescale MCF54418 TWR board. + * + * Copyright 2010-2012 Freescale Semiconductor, Inc. + * TsiChung Liew (Tsi-Chung.Liew@freescale.com) + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef _M54418TWR_H +#define _M54418TWR_H + +#include <linux/stringify.h> + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MCFUART +#define CONFIG_SYS_UART_PORT (0) +#define CONFIG_SYS_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 } + +#define LDS_BOARD_TEXT board/freescale/m54418twr/sbf_dram_init.o (.text*) + +#undef CONFIG_WATCHDOG + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +/* + * NAND FLASH + */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_JFFS2_NAND +#define CONFIG_NAND_FSL_NFC +#define CONFIG_SYS_NAND_BASE 0xFC0FC000 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE +#define CONFIG_SYS_NAND_SELECT_DEVICE +#endif + +/* Network configuration */ +#ifdef CONFIG_MCFFEC +#define CONFIG_MII_INIT 1 +#define CONFIG_SYS_DISCOVER_PHY +#define CONFIG_SYS_RX_ETH_BUFFER 2 +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN +#define CONFIG_SYS_TX_ETH_BUFFER 2 +#define CONFIG_HAS_ETH1 + +#define CONFIG_ETHPRIME "FEC0" +#define CONFIG_IPADDR 192.168.1.2 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 + +#define CONFIG_SYS_FEC_BUF_USE_SRAM +/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ +#ifndef CONFIG_SYS_DISCOVER_PHY +#define FECDUPLEX FULL +#define FECSPEED _100BASET +#define LINKSTATUS 1 +#else +#define LINKSTATUS 0 +#ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN +#endif +#endif /* CONFIG_SYS_DISCOVER_PHY */ +#endif + +#define CONFIG_HOSTNAME "M54418TWR" + +#if defined(CONFIG_CF_SBF) +/* ST Micro serial flash */ +#define CONFIG_SYS_LOAD_ADDR2 0x40010007 +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ + "loadaddr=0x40010000\0" \ + "sbfhdr=sbfhdr.bin\0" \ + "uboot=u-boot.bin\0" \ + "load=tftp ${loadaddr} ${sbfhdr};" \ + "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \ + "upd=run load; run prog\0" \ + "prog=sf probe 0:1 1000000 3;" \ + "sf erase 0 40000;" \ + "sf write ${loadaddr} 0 40000;" \ + "save\0" \ + "" +#elif defined(CONFIG_SYS_NAND_BOOT) +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ + "loadaddr=0x40010000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr} ${u-boot};\0" \ + "upd=run load; run prog\0" \ + "prog=nand device 0;" \ + "nand erase 0 40000;" \ + "nb_update ${loadaddr} ${filesize};" \ + "save\0" \ + "" +#else +#define CONFIG_SYS_UBOOT_END 0x3FFFF +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ + "loadaddr=40010000\0" \ + "u-boot=u-boot.bin\0" \ + "load=tftp ${loadaddr) ${u-boot}\0" \ + "upd=run load; run prog\0" \ + "prog=prot off mram" " ;" \ + "cp.b ${loadaddr} 0 ${filesize};" \ + "save\0" \ + "" +#endif + +/* Realtime clock */ +#undef CONFIG_MCFRTC +#define CONFIG_RTC_MCFRRTC +#define CONFIG_SYS_MCFRRTC_BASE 0xFC0A8000 + +/* Timer */ +#define CONFIG_MCFTMR + +/* I2c */ +#undef CONFIG_SYS_FSL_I2C +#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ +/* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 80000 +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x58000 +#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR + +/* DSPI and Serial Flash */ +#define CONFIG_CF_DSPI +#define CONFIG_SERIAL_FLASH +#define CONFIG_SYS_SBFHDR_SIZE 0x7 + +/* Input, PCI, Flexbus, and VCO */ +#define CONFIG_EXTRA_CLOCK + +#define CONFIG_PRAM 2048 /* 2048 KB */ + +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) + +#define CONFIG_SYS_MBAR 0xFC000000 + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 +/* End of used area in internal SRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +#define CONFIG_SYS_INIT_RAM_CTRL 0x221 +#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) - 32) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */ + +#define CONFIG_SYS_DRAM_TEST + +#if defined(CONFIG_CF_SBF) || defined(CONFIG_SYS_NAND_BOOT) +#define CONFIG_SERIAL_BOOT +#endif + +#if defined(CONFIG_SERIAL_BOOT) +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) +#else +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) +#endif + +#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024) +/* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +/* Reserve 256 kB for malloc() */ +#define CONFIG_SYS_MALLOC_LEN (256 << 10) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization ?? + */ +/* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \ + (CONFIG_SYS_SDRAM_SIZE << 20)) + +/* Configuration for environment + * Environment is embedded in u-boot in the second sector of the flash + */ + +/* FLASH organization */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE + +#ifdef CONFIG_SYS_FLASH_CFI + +/* Max size that the board might have */ +#define CONFIG_SYS_FLASH_SIZE 0x1000000 +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +/* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +/* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 270 +/* "Real" (hardware) sectors protection */ +#define CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE } +#else +/* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_SECT 270 +/* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 0 +#endif + +/* + * This is setting for JFFS2 support in u-boot. + * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. + */ +#ifdef CONFIG_CMD_JFFS2 +#define CONFIG_JFFS2_DEV "nand0" +#define CONFIG_JFFS2_PART_OFFSET (0x800000) + +#endif + +/* Cache Configuration */ +#define CONFIG_SYS_CACHELINE_SIZE 16 +#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 4) +#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) +#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) +#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ + CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ + CF_ACR_EN | CF_ACR_SM_ALL) +#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ + CF_CACR_ICINVA | CF_CACR_EUSP) +#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ + CF_CACR_DEC | CF_CACR_DDCM_P | \ + CF_CACR_DCINVA) & ~CF_CACR_ICINVA) + +#define CACR_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - 12) + +/*----------------------------------------------------------------------- + * Memory bank definitions + */ +/* + * CS0 - NOR Flash 16MB + * CS1 - Available + * CS2 - Available + * CS3 - Available + * CS4 - Available + * CS5 - Available + */ + + /* Flash */ +#define CONFIG_SYS_CS0_BASE 0x00000000 +#define CONFIG_SYS_CS0_MASK 0x000F0101 +#define CONFIG_SYS_CS0_CTRL 0x00001D60 + +#endif /* _M54418TWR_H */ |