diff options
Diffstat (limited to 'roms/u-boot/include/configs/MPC8315ERDB.h')
| -rw-r--r-- | roms/u-boot/include/configs/MPC8315ERDB.h | 370 |
1 files changed, 370 insertions, 0 deletions
diff --git a/roms/u-boot/include/configs/MPC8315ERDB.h b/roms/u-boot/include/configs/MPC8315ERDB.h new file mode 100644 index 000000000..688aa5ea9 --- /dev/null +++ b/roms/u-boot/include/configs/MPC8315ERDB.h @@ -0,0 +1,370 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2007-2010 Freescale Semiconductor, Inc. + * + * Dave Liu <daveliu@freescale.com> + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 +#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH 0x00000000 +#define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */ + +#define CONFIG_HWCONFIG + +/* + * DDR Setup + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ + | DDRCDR_PZ_LOZ \ + | DDRCDR_NZ_LOZ \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x7b880001 */ +/* + * Manually set up DDR parameters + * consist of two chips HY5PS12621BFP-C4 from HYNIX + */ +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ODT_RD_NEVER \ + | CSCONFIG_ODT_WR_ONLY_CURRENT \ + | CSCONFIG_ROW_BIT_13 \ + | CSCONFIG_COL_BIT_10) + /* 0x80010102 */ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ + | (0 << TIMING_CFG0_WRT_SHIFT) \ + | (0 << TIMING_CFG0_RRT_SHIFT) \ + | (0 << TIMING_CFG0_WWT_SHIFT) \ + | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ + | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ + | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) + /* 0x00220802 */ +#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ + | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ + | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ + | (5 << TIMING_CFG1_CASLAT_SHIFT) \ + | (6 << TIMING_CFG1_REFREC_SHIFT) \ + | (2 << TIMING_CFG1_WRREC_SHIFT) \ + | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ + | (2 << TIMING_CFG1_WRTORD_SHIFT)) + /* 0x27256222 */ +#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ + | (4 << TIMING_CFG2_CPO_SHIFT) \ + | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ + | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ + | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ + | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ + | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) + /* 0x121048c5 */ +#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ + | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) + /* 0x03600100 */ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ + | SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_DBW_32) + /* 0x43080000 */ +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ + | (0x0232 << SDRAM_MODE_SD_SHIFT)) + /* ODT 150ohm CL=3, AL=1 on SDRAM */ +#define CONFIG_SYS_DDR_MODE2 0x00000000 + +/* + * Memory test + */ +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +/* 127 64KB sectors and 8 8KB top sectors per device */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 + +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +/* + * NAND Flash on the Local Bus + */ + +#ifdef CONFIG_NAND_SPL +#define CONFIG_SYS_NAND_BASE 0xFFF00000 +#else +#define CONFIG_SYS_NAND_BASE 0xE0600000 +#endif + +#define CONFIG_MTD_PARTITION + +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_NAND_FSL_ELBC 1 +#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 +#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */ + +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 +#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 + + + +/* Still needed for spl_minimal.c */ +#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM +#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM + +#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \ + !defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +/* + * Serial Port + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } + +/* + * Board info - revision and where boot from + */ +#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 + +/* + * Config on-board RTC + */ +#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE +#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE +#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 +#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ + +#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 +#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 + +#define CONFIG_SYS_PCIE1_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 +#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 + +#define CONFIG_SYS_PCIE2_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 +#define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000 +#define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000 +#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 + +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCIE + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#define CONFIG_HAS_FSL_DR_USB +#define CONFIG_SYS_SCCR_USBDRCM 3 + +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_PHY_TYPE "utmi" +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET + +/* + * TSEC + */ +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) + +/* + * TSEC ethernet configuration + */ +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "eTSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "eTSEC1" +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: eTSEC[0-1] */ +#define CONFIG_ETHPRIME "eTSEC1" + +/* + * SATA + */ +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA1 +#define CONFIG_SYS_SATA1_OFFSET 0x18000 +#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SATA2 +#define CONFIG_SYS_SATA2_OFFSET 0x19000 +#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA + +#ifdef CONFIG_FSL_SATA +#define CONFIG_LBA48 +#endif + +/* + * Environment + */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +/* + * MMU Setup + */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#endif + +/* + * Environment Configuration + */ + +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#endif + +#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=ramfs.83xx\0" \ + "fdtaddr=780000\0" \ + "fdtfile=mpc8315erdb.dtb\0" \ + "usb_phy_type=utmi\0" \ + "" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ + "$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ |