diff options
Diffstat (limited to 'roms/u-boot/include/configs/ls2080ardb.h')
| -rw-r--r-- | roms/u-boot/include/configs/ls2080ardb.h | 586 |
1 files changed, 586 insertions, 0 deletions
diff --git a/roms/u-boot/include/configs/ls2080ardb.h b/roms/u-boot/include/configs/ls2080ardb.h new file mode 100644 index 000000000..f2dc495fb --- /dev/null +++ b/roms/u-boot/include/configs/ls2080ardb.h @@ -0,0 +1,586 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2017, 2019-2021 NXP + * Copyright 2015 Freescale Semiconductor + */ + +#ifndef __LS2_RDB_H +#define __LS2_RDB_H + +#include "ls2080a_common.h" + +#ifdef CONFIG_FSL_QSPI +#ifdef CONFIG_TARGET_LS2081ARDB +#define CONFIG_QIXIS_I2C_ACCESS +#endif +#if !CONFIG_IS_ENABLED(DM_I2C) +#define CONFIG_SYS_I2C_EARLY_INIT +#endif +#endif + +#define I2C_MUX_CH_VOL_MONITOR 0xa +#define I2C_VOL_MONITOR_ADDR 0x38 +#define CONFIG_VOL_MONITOR_IR36021_READ +#define CONFIG_VOL_MONITOR_IR36021_SET + +#define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv" +#ifndef CONFIG_SPL_BUILD +#define CONFIG_VID +#endif +/* step the IR regulator in 5mV increments */ +#define IR_VDD_STEP_DOWN 5 +#define IR_VDD_STEP_UP 5 +/* The lowest and highest voltage allowed for LS2080ARDB */ +#define VDD_MV_MIN 819 +#define VDD_MV_MAX 1212 + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(void); +#endif + +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() +#define CONFIG_DDR_CLK_FREQ 133333333 +#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) + +#define CONFIG_DDR_SPD +#define CONFIG_DDR_ECC +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER +#define CONFIG_MEM_INIT_VALUE 0xdeadbeef +#define SPD_EEPROM_ADDRESS1 0x51 +#define SPD_EEPROM_ADDRESS2 0x52 +#define SPD_EEPROM_ADDRESS3 0x53 +#define SPD_EEPROM_ADDRESS4 0x54 +#define SPD_EEPROM_ADDRESS5 0x55 +#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */ +#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 +#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ +#define CONFIG_DIMM_SLOTS_PER_CTLR 2 +#define CONFIG_CHIP_SELECTS_PER_CTRL 4 +#ifdef CONFIG_SYS_FSL_HAS_DP_DDR +#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 +#endif + +/* SATA */ +#define CONFIG_SCSI_AHCI_PLAT + +#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 +#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 + +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + +#if !defined(CONFIG_FSL_QSPI) || defined(CONFIG_TFABOOT) + +#define CONFIG_SYS_NOR0_CSPR_EXT (0x0) +#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) +#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) + +#define CONFIG_SYS_NOR0_CSPR \ + (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR0_CSPR_EARLY \ + (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ + CSPR_PORT_SIZE_16 | \ + CSPR_MSEL_NOR | \ + CSPR_V) +#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) +#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ + FTIM0_NOR_TEADC(0x5) | \ + FTIM0_NOR_TEAHC(0x5)) +#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ + FTIM1_NOR_TRAD_NOR(0x1a) |\ + FTIM1_NOR_TSEQRAD_NOR(0x13)) +#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ + FTIM2_NOR_TCH(0x4) | \ + FTIM2_NOR_TWPH(0x0E) | \ + FTIM2_NOR_TWP(0x1c)) +#define CONFIG_SYS_NOR_FTIM3 0x04000000 +#define CONFIG_SYS_IFC_CCR 0x01000000 + +#ifdef CONFIG_MTD_NOR_FLASH +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ + CONFIG_SYS_FLASH_BASE + 0x40000000} +#endif + +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_MAX_ECCPOS 256 +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 + +#define CONFIG_SYS_NAND_CSPR_EXT (0x0) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ + | CSOR_NAND_PGS_4K /* Page Size = 4K */ \ + | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \ + | CSOR_NAND_PB(128)) /* Pages Per Block 128*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x0e) | \ + FTIM0_NAND_TWP(0x30) | \ + FTIM0_NAND_TWCHT(0x0e) | \ + FTIM0_NAND_TWH(0x14)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x64) | \ + FTIM1_NAND_TWBE(0xab) | \ + FTIM1_NAND_TRR(0x1c) | \ + FTIM1_NAND_TRP(0x30)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x1e) | \ + FTIM2_NAND_TREH(0x14) | \ + FTIM2_NAND_TWHRE(0x3c)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE + +#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024) +#define CONFIG_FSL_QIXIS /* use common QIXIS code */ +#define QIXIS_LBMAP_SWITCH 0x06 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_LBMAP_SHIFT 0 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x04 +#define QIXIS_LBMAP_NAND 0x09 +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RST_CTL_RESET_EN 0x30 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_RCW_SRC_NAND 0x119 +#define QIXIS_RST_FORCE_MEM 0x01 + +#define CONFIG_SYS_CSPR3_EXT (0x0) +#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) +#define CONFIG_SYS_CSPR3_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 \ + | CSPR_MSEL_GPCM \ + | CSPR_V) + +#define CONFIG_SYS_AMASK3 IFC_AMASK(64*1024) +#define CONFIG_SYS_CSOR3 CSOR_GPCM_ADM_SHIFT(12) +/* QIXIS Timing parameters for IFC CS3 */ +#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ + FTIM0_GPCM_TEADC(0x0e) | \ + FTIM0_GPCM_TEAHC(0x0e)) +#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ + FTIM1_GPCM_TRAD(0x3f)) +#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ + FTIM2_GPCM_TCH(0xf) | \ + FTIM2_GPCM_TWP(0x3E)) +#define CONFIG_SYS_CS3_FTIM3 0x0 + +#if defined(CONFIG_SPL) && defined(CONFIG_MTD_RAW_NAND) +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR_EARLY +#define CONFIG_SYS_CSPR2_FINAL CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 + +#define CONFIG_SPL_PAD_TO 0x80000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS (1024 * 1024) +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024) +#else +#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY +#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif + +/* Debug Server firmware */ +#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR +#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL +#endif +#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 + +#ifdef CONFIG_TARGET_LS2081ARDB +#define CONFIG_FSL_QIXIS /* use common QIXIS code */ +#define QIXIS_QMAP_MASK 0x07 +#define QIXIS_QMAP_SHIFT 5 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_QSPI 0x00 +#define QIXIS_RCW_SRC_QSPI 0x62 +#define QIXIS_LBMAP_ALTBANK 0x20 +#define QIXIS_RST_CTL_RESET 0x31 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#define QIXIS_LBMAP_MASK 0x0f +#define QIXIS_RST_CTL_RESET_EN 0x30 +#endif + +/* + * I2C + */ +#ifdef CONFIG_TARGET_LS2081ARDB +#define CONFIG_SYS_I2C_FPGA_ADDR 0x66 +#endif +#define I2C_MUX_PCA_ADDR 0x75 +#define I2C_MUX_PCA_ADDR_PRI 0x75 /* Primary Mux*/ + +/* I2C bus multiplexer */ +#define I2C_MUX_CH_DEFAULT 0x8 + +/* SPI */ +#if defined(CONFIG_FSL_DSPI) +#define CONFIG_SPI_FLASH_STMICRO +#endif + +/* + * RTC configuration + */ +#define RTC +#ifdef CONFIG_TARGET_LS2081ARDB +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 +#else +#define CONFIG_RTC_DS3231 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#endif + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + +#define CONFIG_FSL_MEMAC + +#ifdef CONFIG_PCI +#define CONFIG_PCI_SCAN_SHOW +#endif + +#define BOOT_TARGET_DEVICES(func) \ + func(USB, usb, 0) \ + func(MMC, mmc, 0) \ + func(SCSI, scsi, 0) \ + func(DHCP, dhcp, na) +#include <config_distro_bootcmd.h> + +#ifdef CONFIG_TFABOOT +#define QSPI_MC_INIT_CMD \ + "sf probe 0:0; " \ + "sf read 0x80640000 0x640000 0x80000; " \ + "env exists secureboot && " \ + "esbc_validate 0x80640000 && " \ + "esbc_validate 0x80680000; " \ + "sf read 0x80a00000 0xa00000 0x300000; " \ + "sf read 0x80e00000 0xe00000 0x100000; " \ + "fsl_mc start mc 0x80a00000 0x80e00000 \0" +#define SD_MC_INIT_CMD \ + "mmcinfo;mmc read 0x80a00000 0x5000 0x1200;" \ + "mmc read 0x80e00000 0x7000 0x800;" \ + "env exists secureboot && " \ + "mmc read 0x80640000 0x3200 0x20 && " \ + "mmc read 0x80680000 0x3400 0x20 && " \ + "esbc_validate 0x80640000 && " \ + "esbc_validate 0x80680000 ;" \ + "fsl_mc start mc 0x80a00000 0x80e00000\0" +#define IFC_MC_INIT_CMD \ + "env exists secureboot && " \ + "esbc_validate 0x580640000 && " \ + "esbc_validate 0x580680000; " \ + "fsl_mc start mc 0x580a00000 0x580e00000 \0" +#else +#ifdef CONFIG_QSPI_BOOT +#define MC_INIT_CMD \ + "mcinitcmd=sf probe 0:0; " \ + "sf read 0x80640000 0x640000 0x80000; " \ + "env exists secureboot && " \ + "esbc_validate 0x80640000 && " \ + "esbc_validate 0x80680000; " \ + "sf read 0x80a00000 0xa00000 0x300000; " \ + "sf read 0x80e00000 0xe00000 0x100000; " \ + "fsl_mc start mc 0x80a00000 0x80e00000 \0" +#elif defined(CONFIG_SD_BOOT) +#define MC_INIT_CMD \ + "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \ + "mmc read 0x80100000 0x7000 0x800;" \ + "env exists secureboot && " \ + "mmc read 0x80640000 0x3200 0x20 && " \ + "mmc read 0x80680000 0x3400 0x20 && " \ + "esbc_validate 0x80640000 && " \ + "esbc_validate 0x80680000 ;" \ + "fsl_mc start mc 0x80000000 0x80100000\0" \ + "mcmemsize=0x70000000\0" +#else +#define MC_INIT_CMD \ + "mcinitcmd=env exists secureboot && " \ + "esbc_validate 0x580640000 && " \ + "esbc_validate 0x580680000; " \ + "fsl_mc start mc 0x580a00000 0x580e00000 \0" +#endif +#endif + +/* Initial environment variables */ +#undef CONFIG_EXTRA_ENV_SETTINGS +#ifdef CONFIG_TFABOOT +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:bank_intlv=auto\0" \ + "ramdisk_addr=0x800000\0" \ + "ramdisk_size=0x2000000\0" \ + "fdt_high=0xa0000000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "fdt_addr=0x64f00000\0" \ + "kernel_addr=0x581000000\0" \ + "kernel_start=0x1000000\0" \ + "kernelheader_start=0x800000\0" \ + "scriptaddr=0x80000000\0" \ + "scripthdraddr=0x80080000\0" \ + "fdtheader_addr_r=0x80100000\0" \ + "kernelheader_addr_r=0x80200000\0" \ + "kernelheader_addr=0x580600000\0" \ + "kernel_addr_r=0x81000000\0" \ + "kernelheader_size=0x40000\0" \ + "fdt_addr_r=0x90000000\0" \ + "load_addr=0xa0000000\0" \ + "kernel_size=0x2800000\0" \ + "kernel_addr_sd=0x8000\0" \ + "kernel_size_sd=0x14000\0" \ + "console=ttyAMA0,38400n8\0" \ + "mcmemsize=0x70000000\0" \ + "sd_bootcmd=echo Trying load from SD ..;" \ + "mmcinfo; mmc read $load_addr " \ + "$kernel_addr_sd $kernel_size_sd && " \ + "bootm $load_addr#$board\0" \ + QSPI_MC_INIT_CMD \ + BOOTENV \ + "boot_scripts=ls2088ardb_boot.scr\0" \ + "boot_script_hdr=hdr_ls2088ardb_bs.out\0" \ + "scan_dev_for_boot_part=" \ + "part list ${devtype} ${devnum} devplist; " \ + "env exists devplist || setenv devplist 1; " \ + "for distro_bootpart in ${devplist}; do " \ + "if fstype ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "bootfstype; then " \ + "run scan_dev_for_boot; " \ + "fi; " \ + "done\0" \ + "boot_a_script=" \ + "load ${devtype} ${devnum}:${distro_bootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "env exists secureboot && load ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "${scripthdraddr} ${prefix}${boot_script_hdr} " \ + "&& esbc_validate ${scripthdraddr};" \ + "source ${scriptaddr}\0" \ + "qspi_bootcmd=echo Trying load from qspi..;" \ + "sf probe && sf read $load_addr " \ + "$kernel_start $kernel_size ; env exists secureboot &&" \ + "sf read $kernelheader_addr_r $kernelheader_start " \ + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ + " bootm $load_addr#$board\0" \ + "nor_bootcmd=echo Trying load from nor..;" \ + "cp.b $kernel_addr $load_addr " \ + "$kernel_size ; env exists secureboot && " \ + "cp.b $kernelheader_addr $kernelheader_addr_r " \ + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ + "bootm $load_addr#$board\0" +#else +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=fsl_ddr:bank_intlv=auto\0" \ + "ramdisk_addr=0x800000\0" \ + "ramdisk_size=0x2000000\0" \ + "fdt_high=0xa0000000\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "fdt_addr=0x64f00000\0" \ + "kernel_addr=0x581000000\0" \ + "kernel_start=0x1000000\0" \ + "kernelheader_start=0x600000\0" \ + "scriptaddr=0x80000000\0" \ + "scripthdraddr=0x80080000\0" \ + "fdtheader_addr_r=0x80100000\0" \ + "kernelheader_addr_r=0x80200000\0" \ + "kernelheader_addr=0x580600000\0" \ + "kernel_addr_r=0x81000000\0" \ + "kernelheader_size=0x40000\0" \ + "fdt_addr_r=0x90000000\0" \ + "load_addr=0xa0000000\0" \ + "kernel_size=0x2800000\0" \ + "kernel_addr_sd=0x8000\0" \ + "kernel_size_sd=0x14000\0" \ + "console=ttyAMA0,38400n8\0" \ + "mcmemsize=0x70000000\0" \ + "sd_bootcmd=echo Trying load from SD ..;" \ + "mmcinfo; mmc read $load_addr " \ + "$kernel_addr_sd $kernel_size_sd && " \ + "bootm $load_addr#$board\0" \ + MC_INIT_CMD \ + BOOTENV \ + "boot_scripts=ls2088ardb_boot.scr\0" \ + "boot_script_hdr=hdr_ls2088ardb_bs.out\0" \ + "scan_dev_for_boot_part=" \ + "part list ${devtype} ${devnum} devplist; " \ + "env exists devplist || setenv devplist 1; " \ + "for distro_bootpart in ${devplist}; do " \ + "if fstype ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "bootfstype; then " \ + "run scan_dev_for_boot; " \ + "fi; " \ + "done\0" \ + "boot_a_script=" \ + "load ${devtype} ${devnum}:${distro_bootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "env exists secureboot && load ${devtype} " \ + "${devnum}:${distro_bootpart} " \ + "${scripthdraddr} ${prefix}${boot_script_hdr}; " \ + "env exists secureboot " \ + "&& esbc_validate ${scripthdraddr};" \ + "source ${scriptaddr}\0" \ + "qspi_bootcmd=echo Trying load from qspi..;" \ + "sf probe && sf read $load_addr " \ + "$kernel_start $kernel_size ; env exists secureboot &&" \ + "sf read $kernelheader_addr_r $kernelheader_start " \ + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ + " bootm $load_addr#$board\0" \ + "nor_bootcmd=echo Trying load from nor..;" \ + "cp.b $kernel_addr $load_addr " \ + "$kernel_size ; env exists secureboot && " \ + "cp.b $kernelheader_addr $kernelheader_addr_r " \ + "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\ + "bootm $load_addr#$board\0" +#endif + +#ifdef CONFIG_TFABOOT +#define QSPI_NOR_BOOTCOMMAND \ + "sf probe 0:0; " \ + "sf read 0x806c0000 0x6c0000 0x40000; " \ + "env exists mcinitcmd && env exists secureboot "\ + "&& esbc_validate 0x806c0000; " \ + "sf read 0x80d00000 0xd00000 0x100000; " \ + "env exists mcinitcmd && " \ + "fsl_mc lazyapply dpl 0x80d00000; " \ + "run distro_bootcmd;run qspi_bootcmd; " \ + "env exists secureboot && esbc_halt;" + +/* Try to boot an on-SD kernel first, then do normal distro boot */ +#define SD_BOOTCOMMAND \ + "env exists mcinitcmd && env exists secureboot "\ + "&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \ + "&& esbc_validate $load_addr; " \ + "env exists mcinitcmd && run mcinitcmd " \ + "&& mmc read 0x80d00000 0x6800 0x800 " \ + "&& fsl_mc lazyapply dpl 0x80d00000; " \ + "run distro_bootcmd;run sd_bootcmd; " \ + "env exists secureboot && esbc_halt;" + +/* Try to boot an on-NOR kernel first, then do normal distro boot */ +#define IFC_NOR_BOOTCOMMAND \ + "env exists mcinitcmd && env exists secureboot "\ + "&& esbc_validate 0x5806C0000; env exists mcinitcmd "\ + "&& fsl_mc lazyapply dpl 0x580d00000;" \ + "run distro_bootcmd;run nor_bootcmd; " \ + "env exists secureboot && esbc_halt;" +#else +#undef CONFIG_BOOTCOMMAND +#ifdef CONFIG_QSPI_BOOT +/* Try to boot an on-QSPI kernel first, then do normal distro boot */ +#define CONFIG_BOOTCOMMAND \ + "sf probe 0:0; " \ + "sf read 0x806c0000 0x6c0000 0x40000; " \ + "env exists mcinitcmd && env exists secureboot "\ + "&& esbc_validate 0x806C0000; " \ + "sf read 0x80d00000 0xd00000 0x100000; " \ + "env exists mcinitcmd && " \ + "fsl_mc lazyapply dpl 0x80d00000; " \ + "run distro_bootcmd;run qspi_bootcmd; " \ + "env exists secureboot && esbc_halt;" +#elif defined(CONFIG_SD_BOOT) +/* Try to boot an on-SD kernel first, then do normal distro boot */ +#define CONFIG_BOOTCOMMAND \ + "env exists mcinitcmd && env exists secureboot "\ + "&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \ + "&& esbc_validate $load_addr; " \ + "env exists mcinitcmd && run mcinitcmd " \ + "&& mmc read 0x88000000 0x6800 0x800 " \ + "&& fsl_mc lazyapply dpl 0x88000000; " \ + "run distro_bootcmd;run sd_bootcmd; " \ + "env exists secureboot && esbc_halt;" +#else +/* Try to boot an on-NOR kernel first, then do normal distro boot */ +#define CONFIG_BOOTCOMMAND \ + "env exists mcinitcmd && env exists secureboot "\ + "&& esbc_validate 0x5806C0000; env exists mcinitcmd "\ + "&& fsl_mc lazyapply dpl 0x580d00000;" \ + "run distro_bootcmd;run nor_bootcmd; " \ + "env exists secureboot && esbc_halt;" +#endif +#endif + +/* MAC/PHY configuration */ +#ifdef CONFIG_FSL_MC_ENET +#ifdef CONFIG_QSPI_BOOT +#define CONFIG_CORTINA_FW_ADDR 0x20980000 +#else +#define CONFIG_CORTINA_FW_ADDR 0x580980000 +#endif +#define CONFIG_CORTINA_FW_LENGTH 0x40000 + +#define CORTINA_PHY_ADDR1 0x10 +#define CORTINA_PHY_ADDR2 0x11 +#define CORTINA_PHY_ADDR3 0x12 +#define CORTINA_PHY_ADDR4 0x13 +#define AQ_PHY_ADDR1 0x00 +#define AQ_PHY_ADDR2 0x01 +#define AQ_PHY_ADDR3 0x02 +#define AQ_PHY_ADDR4 0x03 +#define AQR405_IRQ_MASK 0x36 + +#define CONFIG_ETHPRIME "DPMAC1@xgmii" +#endif + +#include <asm/fsl_secure_boot.h> + +#endif /* __LS2_RDB_H */ |