diff options
Diffstat (limited to 'roms/u-boot/include/configs/socrates.h')
| -rw-r--r-- | roms/u-boot/include/configs/socrates.h | 284 |
1 files changed, 284 insertions, 0 deletions
diff --git a/roms/u-boot/include/configs/socrates.h b/roms/u-boot/include/configs/socrates.h new file mode 100644 index 000000000..da6054696 --- /dev/null +++ b/roms/u-boot/include/configs/socrates.h @@ -0,0 +1,284 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2008 + * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. + * + * Wolfgang Denk <wd@denx.de> + * Copyright 2004 Freescale Semiconductor. + * (C) Copyright 2002,2003 Motorola,Inc. + * Xianghua Xiao <X.Xiao@motorola.com> + */ + +/* + * Socrates + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_SOCRATES 1 + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +/* + * sysclk for MPC85xx + * + * Two valid values are: + * 33000000 + * 66000000 + * + * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz + * is likely the desired value here, so that is now the default. + * The board, however, can run at 66MHz. In any event, this value + * must match the settings of some switches. Details can be found + * in the README.mpc85xxads. + */ + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ 66666666 +#endif + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ + +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ + +#define CONFIG_SYS_CCSRBAR 0xE0000000 +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR + +/* DDR Setup */ +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#define CONFIG_DDR_SPD + +#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_VERY_BIG_RAM + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 2 + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS 0x50 /* CTLR 0 DIMM 0 */ + +#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ + +/* Hardcoded values, to use instead of SPD */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 +#define CONFIG_SYS_DDR_TIMING_0 0x00260802 +#define CONFIG_SYS_DDR_TIMING_1 0x3935D322 +#define CONFIG_SYS_DDR_TIMING_2 0x14904CC8 +#define CONFIG_SYS_DDR_MODE 0x00480432 +#define CONFIG_SYS_DDR_INTERVAL 0x030C0100 +#define CONFIG_SYS_DDR_CONFIG_2 0x04400000 +#define CONFIG_SYS_DDR_CONFIG 0xC3008000 +#define CONFIG_SYS_DDR_CLK_CONTROL 0x03800000 +#define CONFIG_SYS_SDRAM_SIZE 256 /* in Megs */ + +/* + * Flash on the LocalBus + */ +#define CONFIG_SYS_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ + +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_SYS_FLASH0 0xFE000000 +#define CONFIG_SYS_FLASH1 0xFC000000 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } + +#define CONFIG_SYS_LBC_FLASH_BASE CONFIG_SYS_FLASH1 /* Localbus flash start */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_LBC_FLASH_BASE /* start of FLASH */ + +#define CONFIG_SYS_BR0_PRELIM 0xfe001001 /* port size 16bit */ +#define CONFIG_SYS_OR0_PRELIM 0xfe000030 /* 32MB Flash */ +#define CONFIG_SYS_BR1_PRELIM 0xfc001001 /* port size 16bit */ +#define CONFIG_SYS_OR1_PRELIM 0xfe000030 /* 32MB Flash */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ +#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size used area in RAM*/ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384KiB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc */ + +/* FPGA and NAND */ +#define CONFIG_SYS_FPGA_BASE 0xc0000000 +#define CONFIG_SYS_FPGA_SIZE 0x00100000 /* 1 MB */ +#define CONFIG_SYS_HMI_BASE 0xc0010000 +#define CONFIG_SYS_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ +#define CONFIG_SYS_OR3_PRELIM 0xfff00000 /* 1 MB */ + +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_FPGA_BASE + 0x70) +#define CONFIG_SYS_MAX_NAND_DEVICE 1 + +/* LIME GDC */ +#define CONFIG_SYS_LIME_BASE 0xc8000000 +#define CONFIG_SYS_LIME_SIZE 0x04000000 /* 64 MB */ +#define CONFIG_SYS_BR2_PRELIM 0xc80018a1 /* UPMB, 32-bit */ +#define CONFIG_SYS_OR2_PRELIM 0xfc000000 /* 64 MB */ + +#define CONFIG_SYS_SPD_BUS_NUM 0 + +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 + +/* + * General PCI + * Memory space is mapped 1-1. + */ + +/* PCI is clocked by the external source at 33 MHz */ +#define CONFIG_PCI_CLK_FREQ 33000000 +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BASE 0xE2000000 +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE +#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16M */ + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "TSEC1" +#undef CONFIG_MPC85XX_FEC + +#define TSEC1_PHY_ADDR 0 +#define TSEC3_PHY_ADDR 1 + +#define TSEC1_PHYIDX 0 +#define TSEC3_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC3_FLAGS TSEC_GIGABIT + +/* Options are: TSEC[0,1] */ +#define CONFIG_ETHPRIME "TSEC0" + +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 + +/* + * Environment + */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_TIMESTAMP /* Print image info with ts */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ +#endif + +#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consdev=ttyS0\0" \ + "uboot_file=/home/tftp/syscon3/u-boot.bin\0" \ + "bootfile=/home/tftp/syscon3/uImage\0" \ + "fdt_file=/home/tftp/syscon3/socrates.dtb\0" \ + "initrd_file=/home/tftp/syscon3/uinitrd.gz\0" \ + "uboot_addr=FFF60000\0" \ + "kernel_addr=FE000000\0" \ + "fdt_addr=FE1E0000\0" \ + "ramdisk_addr=FE200000\0" \ + "fdt_addr_r=B00000\0" \ + "kernel_addr_r=200000\0" \ + "ramdisk_addr_r=400000\0" \ + "rootpath=/opt/eldk/ppc_85xxDP\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath\0" \ + "addcons=setenv bootargs $bootargs " \ + "console=$consdev,$baudrate\0" \ + "addip=setenv bootargs $bootargs " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ + ":$hostname:$netdev:off panic=1\0" \ + "boot_nor=run ramargs addcons;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ + "tftp ${fdt_addr_r} ${fdt_file}; " \ + "run nfsargs addip addcons;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "update_uboot=tftp 100000 ${uboot_file};" \ + "protect off fff60000 ffffffff;" \ + "era fff60000 ffffffff;" \ + "cp.b 100000 fff60000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "update_kernel=tftp 100000 ${bootfile};" \ + "era fe000000 fe1dffff;" \ + "cp.b 100000 fe000000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "update_fdt=tftp 100000 ${fdt_file};" \ + "era fe1e0000 fe1fffff;" \ + "cp.b 100000 fe1e0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "update_initrd=tftp 100000 ${initrd_file};" \ + "era fe200000 fe9fffff;" \ + "cp.b 100000 fe200000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "clean_data=era fea00000 fff5ffff\0" \ + "usbargs=setenv bootargs root=/dev/sda1 rw\0" \ + "load_usb=usb start;" \ + "ext2load usb 0:1 ${kernel_addr_r} /boot/uImage\0" \ + "boot_usb=run load_usb usbargs addcons;" \ + "bootm ${kernel_addr_r} - ${fdt_addr};" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "" +#define CONFIG_BOOTCOMMAND "run boot_nor" + +/* pass open firmware flat tree */ + +/* USB support */ +#define CONFIG_USB_OHCI_NEW 1 +#define CONFIG_PCI_OHCI 1 +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" +#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 + +#endif /* __CONFIG_H */ |