diff options
Diffstat (limited to 'roms/u-boot/include/linux/mtd')
23 files changed, 5571 insertions, 0 deletions
diff --git a/roms/u-boot/include/linux/mtd/bbm.h b/roms/u-boot/include/linux/mtd/bbm.h new file mode 100644 index 000000000..7239eb112 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/bbm.h @@ -0,0 +1,161 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * linux/include/linux/mtd/bbm.h + * + * NAND family Bad Block Management (BBM) header file + * - Bad Block Table (BBT) implementation + * + * Copyright © 2005 Samsung Electronics + * Kyungmin Park <kyungmin.park@samsung.com> + * + * Copyright © 2000-2005 + * Thomas Gleixner <tglx@linuxtronix.de> + * + */ +#ifndef __LINUX_MTD_BBM_H +#define __LINUX_MTD_BBM_H + +/* The maximum number of NAND chips in an array */ +#ifndef CONFIG_SYS_NAND_MAX_CHIPS +#define CONFIG_SYS_NAND_MAX_CHIPS 1 +#endif + +/** + * struct nand_bbt_descr - bad block table descriptor + * @options: options for this descriptor + * @pages: the page(s) where we find the bbt, used with option BBT_ABSPAGE + * when bbt is searched, then we store the found bbts pages here. + * Its an array and supports up to 8 chips now + * @offs: offset of the pattern in the oob area of the page + * @veroffs: offset of the bbt version counter in the oob are of the page + * @version: version read from the bbt page during scan + * @len: length of the pattern, if 0 no pattern check is performed + * @maxblocks: maximum number of blocks to search for a bbt. This number of + * blocks is reserved at the end of the device where the tables are + * written. + * @reserved_block_code: if non-0, this pattern denotes a reserved (rather than + * bad) block in the stored bbt + * @pattern: pattern to identify bad block table or factory marked good / + * bad blocks, can be NULL, if len = 0 + * + * Descriptor for the bad block table marker and the descriptor for the + * pattern which identifies good and bad blocks. The assumption is made + * that the pattern and the version count are always located in the oob area + * of the first block. + */ +struct nand_bbt_descr { + int options; + int pages[CONFIG_SYS_NAND_MAX_CHIPS]; + int offs; + int veroffs; + uint8_t version[CONFIG_SYS_NAND_MAX_CHIPS]; + int len; + int maxblocks; + int reserved_block_code; + uint8_t *pattern; +}; + +/* Options for the bad block table descriptors */ + +/* The number of bits used per block in the bbt on the device */ +#define NAND_BBT_NRBITS_MSK 0x0000000F +#define NAND_BBT_1BIT 0x00000001 +#define NAND_BBT_2BIT 0x00000002 +#define NAND_BBT_4BIT 0x00000004 +#define NAND_BBT_8BIT 0x00000008 +/* The bad block table is in the last good block of the device */ +#define NAND_BBT_LASTBLOCK 0x00000010 +/* The bbt is at the given page, else we must scan for the bbt */ +#define NAND_BBT_ABSPAGE 0x00000020 +/* bbt is stored per chip on multichip devices */ +#define NAND_BBT_PERCHIP 0x00000080 +/* bbt has a version counter at offset veroffs */ +#define NAND_BBT_VERSION 0x00000100 +/* Create a bbt if none exists */ +#define NAND_BBT_CREATE 0x00000200 +/* + * Create an empty BBT with no vendor information. Vendor's information may be + * unavailable, for example, if the NAND controller has a different data and OOB + * layout or if this information is already purged. Must be used in conjunction + * with NAND_BBT_CREATE. + */ +#define NAND_BBT_CREATE_EMPTY 0x00000400 +/* Write bbt if neccecary */ +#define NAND_BBT_WRITE 0x00002000 +/* Read and write back block contents when writing bbt */ +#define NAND_BBT_SAVECONTENT 0x00004000 +/* Search good / bad pattern on the first and the second page */ +#define NAND_BBT_SCAN2NDPAGE 0x00008000 +/* Search good / bad pattern on the last page of the eraseblock */ +#define NAND_BBT_SCANLASTPAGE 0x00010000 +/* + * Use a flash based bad block table. By default, OOB identifier is saved in + * OOB area. This option is passed to the default bad block table function. + */ +#define NAND_BBT_USE_FLASH 0x00020000 +/* + * Do not store flash based bad block table marker in the OOB area; store it + * in-band. + */ +#define NAND_BBT_NO_OOB 0x00040000 +/* + * Do not write new bad block markers to OOB; useful, e.g., when ECC covers + * entire spare area. Must be used with NAND_BBT_USE_FLASH. + */ +#define NAND_BBT_NO_OOB_BBM 0x00080000 + +/* + * Flag set by nand_create_default_bbt_descr(), marking that the nand_bbt_descr + * was allocated dynamicaly and must be freed in nand_release(). Has no meaning + * in nand_chip.bbt_options. + */ +#define NAND_BBT_DYNAMICSTRUCT 0x80000000 + +/* The maximum number of blocks to scan for a bbt */ +#define NAND_BBT_SCAN_MAXBLOCKS 4 + +/* + * Constants for oob configuration + */ +#define NAND_SMALL_BADBLOCK_POS 5 +#define NAND_LARGE_BADBLOCK_POS 0 +#define ONENAND_BADBLOCK_POS 0 + +/* + * Bad block scanning errors + */ +#define ONENAND_BBT_READ_ERROR 1 +#define ONENAND_BBT_READ_ECC_ERROR 2 +#define ONENAND_BBT_READ_FATAL_ERROR 4 + +/** + * struct bbm_info - [GENERIC] Bad Block Table data structure + * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry + * @badblockpos: [INTERN] position of the bad block marker in the oob area + * @options: options for this descriptor + * @bbt: [INTERN] bad block table pointer + * @isbad_bbt: function to determine if a block is bad + * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for + * initial bad block scan + * @priv: [OPTIONAL] pointer to private bbm date + */ +struct bbm_info { + int bbt_erase_shift; + int badblockpos; + int options; + + uint8_t *bbt; + + int (*isbad_bbt)(struct mtd_info *mtd, loff_t ofs, int allowbbt); + + /* TODO Add more NAND specific fileds */ + struct nand_bbt_descr *badblock_pattern; + + void *priv; +}; + +/* OneNAND BBT interface */ +extern int onenand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd); +extern int onenand_default_bbt(struct mtd_info *mtd); + +#endif /* __LINUX_MTD_BBM_H */ diff --git a/roms/u-boot/include/linux/mtd/cfi.h b/roms/u-boot/include/linux/mtd/cfi.h new file mode 100644 index 000000000..3555518bd --- /dev/null +++ b/roms/u-boot/include/linux/mtd/cfi.h @@ -0,0 +1,32 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org> et al. + * + */ + +#ifndef __MTD_CFI_H__ +#define __MTD_CFI_H__ + +#define CFI_MFR_ANY 0xFFFF +#define CFI_ID_ANY 0xFFFF +#define CFI_MFR_CONTINUATION 0x007F + +#define CFI_MFR_AMD 0x0001 +#define CFI_MFR_AMIC 0x0037 +#define CFI_MFR_ATMEL 0x001F +#define CFI_MFR_EON 0x001C +#define CFI_MFR_FUJITSU 0x0004 +#define CFI_MFR_HYUNDAI 0x00AD +#define CFI_MFR_INTEL 0x0089 +#define CFI_MFR_MACRONIX 0x00C2 +#define CFI_MFR_NEC 0x0010 +#define CFI_MFR_PMC 0x009D +#define CFI_MFR_SAMSUNG 0x00EC +#define CFI_MFR_SHARP 0x00B0 +#define CFI_MFR_SST 0x00BF +#define CFI_MFR_ST 0x0020 /* STMicroelectronics */ +#define CFI_MFR_MICRON 0x002C /* Micron */ +#define CFI_MFR_TOSHIBA 0x0098 +#define CFI_MFR_WINBOND 0x00DA + +#endif /* __MTD_CFI_H__ */ diff --git a/roms/u-boot/include/linux/mtd/concat.h b/roms/u-boot/include/linux/mtd/concat.h new file mode 100644 index 000000000..c57e97377 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/concat.h @@ -0,0 +1,23 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * MTD device concatenation layer definitions + * + * Copyright © 2002 Robert Kaiser <rkaiser@sysgo.de> + * + */ + +#ifndef MTD_CONCAT_H +#define MTD_CONCAT_H + +struct mtd_info *mtd_concat_create( + struct mtd_info *subdev[], /* subdevices to concatenate */ + int num_devs, /* number of subdevices */ +#ifndef __UBOOT__ + const char *name); /* name for the new device */ +#else + char *name); /* name for the new device */ +#endif + +void mtd_concat_destroy(struct mtd_info *mtd); + +#endif diff --git a/roms/u-boot/include/linux/mtd/doc2000.h b/roms/u-boot/include/linux/mtd/doc2000.h new file mode 100644 index 000000000..d57f8da81 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/doc2000.h @@ -0,0 +1,207 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Linux driver for Disk-On-Chip devices + * + * Copyright © 1999 Machine Vision Holdings, Inc. + * Copyright © 1999-2010 David Woodhouse <dwmw2@infradead.org> + * Copyright © 2002-2003 Greg Ungerer <gerg@snapgear.com> + * Copyright © 2002-2003 SnapGear Inc + * + */ + +#ifndef __MTD_DOC2000_H__ +#define __MTD_DOC2000_H__ + +#include <linux/mtd/mtd.h> +#if 0 +#include <linux/mutex.h> +#endif + +#define DoC_Sig1 0 +#define DoC_Sig2 1 + +#define DoC_ChipID 0x1000 +#define DoC_DOCStatus 0x1001 +#define DoC_DOCControl 0x1002 +#define DoC_FloorSelect 0x1003 +#define DoC_CDSNControl 0x1004 +#define DoC_CDSNDeviceSelect 0x1005 +#define DoC_ECCConf 0x1006 +#define DoC_2k_ECCStatus 0x1007 + +#define DoC_CDSNSlowIO 0x100d +#define DoC_ECCSyndrome0 0x1010 +#define DoC_ECCSyndrome1 0x1011 +#define DoC_ECCSyndrome2 0x1012 +#define DoC_ECCSyndrome3 0x1013 +#define DoC_ECCSyndrome4 0x1014 +#define DoC_ECCSyndrome5 0x1015 +#define DoC_AliasResolution 0x101b +#define DoC_ConfigInput 0x101c +#define DoC_ReadPipeInit 0x101d +#define DoC_WritePipeTerm 0x101e +#define DoC_LastDataRead 0x101f +#define DoC_NOP 0x1020 + +#define DoC_Mil_CDSN_IO 0x0800 +#define DoC_2k_CDSN_IO 0x1800 + +#define DoC_Mplus_NOP 0x1002 +#define DoC_Mplus_AliasResolution 0x1004 +#define DoC_Mplus_DOCControl 0x1006 +#define DoC_Mplus_AccessStatus 0x1008 +#define DoC_Mplus_DeviceSelect 0x1008 +#define DoC_Mplus_Configuration 0x100a +#define DoC_Mplus_OutputControl 0x100c +#define DoC_Mplus_FlashControl 0x1020 +#define DoC_Mplus_FlashSelect 0x1022 +#define DoC_Mplus_FlashCmd 0x1024 +#define DoC_Mplus_FlashAddress 0x1026 +#define DoC_Mplus_FlashData0 0x1028 +#define DoC_Mplus_FlashData1 0x1029 +#define DoC_Mplus_ReadPipeInit 0x102a +#define DoC_Mplus_LastDataRead 0x102c +#define DoC_Mplus_LastDataRead1 0x102d +#define DoC_Mplus_WritePipeTerm 0x102e +#define DoC_Mplus_ECCSyndrome0 0x1040 +#define DoC_Mplus_ECCSyndrome1 0x1041 +#define DoC_Mplus_ECCSyndrome2 0x1042 +#define DoC_Mplus_ECCSyndrome3 0x1043 +#define DoC_Mplus_ECCSyndrome4 0x1044 +#define DoC_Mplus_ECCSyndrome5 0x1045 +#define DoC_Mplus_ECCConf 0x1046 +#define DoC_Mplus_Toggle 0x1046 +#define DoC_Mplus_DownloadStatus 0x1074 +#define DoC_Mplus_CtrlConfirm 0x1076 +#define DoC_Mplus_Power 0x1fff + +/* How to access the device? + * On ARM, it'll be mmap'd directly with 32-bit wide accesses. + * On PPC, it's mmap'd and 16-bit wide. + * Others use readb/writeb + */ +#if defined(__arm__) +#define ReadDOC_(adr, reg) ((unsigned char)(*(volatile __u32 *)(((unsigned long)adr)+((reg)<<2)))) +#define WriteDOC_(d, adr, reg) do{ *(volatile __u32 *)(((unsigned long)adr)+((reg)<<2)) = (__u32)d; wmb();} while(0) +#define DOC_IOREMAP_LEN 0x8000 +#elif defined(__ppc__) +#define ReadDOC_(adr, reg) ((unsigned char)(*(volatile __u16 *)(((unsigned long)adr)+((reg)<<1)))) +#define WriteDOC_(d, adr, reg) do{ *(volatile __u16 *)(((unsigned long)adr)+((reg)<<1)) = (__u16)d; wmb();} while(0) +#define DOC_IOREMAP_LEN 0x4000 +#else +#define ReadDOC_(adr, reg) readb((void __iomem *)(adr) + (reg)) +#define WriteDOC_(d, adr, reg) writeb(d, (void __iomem *)(adr) + (reg)) +#define DOC_IOREMAP_LEN 0x2000 + +#endif + +#if defined(__i386__) || defined(__x86_64__) +#define USE_MEMCPY +#endif + +/* These are provided to directly use the DoC_xxx defines */ +#define ReadDOC(adr, reg) ReadDOC_(adr,DoC_##reg) +#define WriteDOC(d, adr, reg) WriteDOC_(d,adr,DoC_##reg) + +#define DOC_MODE_RESET 0 +#define DOC_MODE_NORMAL 1 +#define DOC_MODE_RESERVED1 2 +#define DOC_MODE_RESERVED2 3 + +#define DOC_MODE_CLR_ERR 0x80 +#define DOC_MODE_RST_LAT 0x10 +#define DOC_MODE_BDECT 0x08 +#define DOC_MODE_MDWREN 0x04 + +#define DOC_ChipID_Doc2k 0x20 +#define DOC_ChipID_Doc2kTSOP 0x21 /* internal number for MTD */ +#define DOC_ChipID_DocMil 0x30 +#define DOC_ChipID_DocMilPlus32 0x40 +#define DOC_ChipID_DocMilPlus16 0x41 + +#define CDSN_CTRL_FR_B 0x80 +#define CDSN_CTRL_FR_B0 0x40 +#define CDSN_CTRL_FR_B1 0x80 + +#define CDSN_CTRL_ECC_IO 0x20 +#define CDSN_CTRL_FLASH_IO 0x10 +#define CDSN_CTRL_WP 0x08 +#define CDSN_CTRL_ALE 0x04 +#define CDSN_CTRL_CLE 0x02 +#define CDSN_CTRL_CE 0x01 + +#define DOC_ECC_RESET 0 +#define DOC_ECC_ERROR 0x80 +#define DOC_ECC_RW 0x20 +#define DOC_ECC__EN 0x08 +#define DOC_TOGGLE_BIT 0x04 +#define DOC_ECC_RESV 0x02 +#define DOC_ECC_IGNORE 0x01 + +#define DOC_FLASH_CE 0x80 +#define DOC_FLASH_WP 0x40 +#define DOC_FLASH_BANK 0x02 + +/* We have to also set the reserved bit 1 for enable */ +#define DOC_ECC_EN (DOC_ECC__EN | DOC_ECC_RESV) +#define DOC_ECC_DIS (DOC_ECC_RESV) + +struct Nand { + char floor, chip; + unsigned long curadr; + unsigned char curmode; + /* Also some erase/write/pipeline info when we get that far */ +}; + +#define MAX_FLOORS 4 +#define MAX_CHIPS 4 + +#define MAX_FLOORS_MIL 1 +#define MAX_CHIPS_MIL 1 + +#define MAX_FLOORS_MPLUS 2 +#define MAX_CHIPS_MPLUS 1 + +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 + +struct DiskOnChip { + unsigned long physadr; + void __iomem *virtadr; + unsigned long totlen; + unsigned char ChipID; /* Type of DiskOnChip */ + int ioreg; + + unsigned long mfr; /* Flash IDs - only one type of flash per device */ + unsigned long id; + int chipshift; + char page256; + char pageadrlen; + char interleave; /* Internal interleaving - Millennium Plus style */ + unsigned long erasesize; + + int curfloor; + int curchip; + + int numchips; + struct Nand *chips; + struct mtd_info *nextdoc; +/* XXX U-BOOT XXX */ +#if 0 + struct mutex lock; +#endif +}; + +int doc_decode_ecc(unsigned char sector[512], unsigned char ecc1[6]); + +/* XXX U-BOOT XXX */ +#if 1 +/* + * NAND Flash Manufacturer ID Codes + */ +#define NAND_MFR_TOSHIBA 0x98 +#define NAND_MFR_SAMSUNG 0xec +#endif + +#endif /* __MTD_DOC2000_H__ */ diff --git a/roms/u-boot/include/linux/mtd/flashchip.h b/roms/u-boot/include/linux/mtd/flashchip.h new file mode 100644 index 000000000..666480db9 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/flashchip.h @@ -0,0 +1,103 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright © 2000 Red Hat UK Limited + * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org> + * + */ + +#ifndef __MTD_FLASHCHIP_H__ +#define __MTD_FLASHCHIP_H__ + +#ifndef __UBOOT__ +/* For spinlocks. sched.h includes spinlock.h from whichever directory it + * happens to be in - so we don't have to care whether we're on 2.2, which + * has asm/spinlock.h, or 2.4, which has linux/spinlock.h + */ +#include <linux/sched.h> +#include <linux/mutex.h> +#endif + +typedef enum { + FL_READY, + FL_STATUS, + FL_CFI_QUERY, + FL_JEDEC_QUERY, + FL_ERASING, + FL_ERASE_SUSPENDING, + FL_ERASE_SUSPENDED, + FL_WRITING, + FL_WRITING_TO_BUFFER, + FL_OTP_WRITE, + FL_WRITE_SUSPENDING, + FL_WRITE_SUSPENDED, + FL_PM_SUSPENDED, + FL_SYNCING, + FL_UNLOADING, + FL_LOCKING, + FL_UNLOCKING, + FL_POINT, + FL_XIP_WHILE_ERASING, + FL_XIP_WHILE_WRITING, + FL_SHUTDOWN, + /* These 2 come from nand_state_t, which has been unified here */ + FL_READING, + FL_CACHEDPRG, + /* These 4 come from onenand_state_t, which has been unified here */ + FL_RESETING, + FL_OTPING, + FL_PREPARING_ERASE, + FL_VERIFYING_ERASE, + + FL_UNKNOWN +} flstate_t; + + + +/* NOTE: confusingly, this can be used to refer to more than one chip at a time, + if they're interleaved. This can even refer to individual partitions on + the same physical chip when present. */ + +struct flchip { + unsigned long start; /* Offset within the map */ + // unsigned long len; + /* We omit len for now, because when we group them together + we insist that they're all of the same size, and the chip size + is held in the next level up. If we get more versatile later, + it'll make it a damn sight harder to find which chip we want from + a given offset, and we'll want to add the per-chip length field + back in. + */ + int ref_point_counter; + flstate_t state; + flstate_t oldstate; + + unsigned int write_suspended:1; + unsigned int erase_suspended:1; + unsigned long in_progress_block_addr; + + struct mutex mutex; +#ifndef __UBOOT__ + wait_queue_head_t wq; /* Wait on here when we're waiting for the chip + to be ready */ +#endif + int word_write_time; + int buffer_write_time; + int erase_time; + + int word_write_time_max; + int buffer_write_time_max; + int erase_time_max; + + void *priv; +}; + +/* This is used to handle contention on write/erase operations + between partitions of the same physical chip. */ +struct flchip_shared { + struct mutex lock; + struct flchip *writing; + struct flchip *erasing; +}; + + +#endif /* __MTD_FLASHCHIP_H__ */ diff --git a/roms/u-boot/include/linux/mtd/fsl_upm.h b/roms/u-boot/include/linux/mtd/fsl_upm.h new file mode 100644 index 000000000..999999354 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/fsl_upm.h @@ -0,0 +1,44 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * FSL UPM NAND driver + * + * Copyright (C) 2007 MontaVista Software, Inc. + * Anton Vorontsov <avorontsov@ru.mvista.com> + */ + +#ifndef __LINUX_MTD_NAND_FSL_UPM +#define __LINUX_MTD_NAND_FSL_UPM + +#include <linux/mtd/rawnand.h> + +#define FSL_UPM_WAIT_RUN_PATTERN 0x1 +#define FSL_UPM_WAIT_WRITE_BYTE 0x2 +#define FSL_UPM_WAIT_WRITE_BUFFER 0x4 + +struct fsl_upm { + void __iomem *mdr; + void __iomem *mxmr; + void __iomem *mar; + void __iomem *io_addr; +}; + +struct fsl_upm_nand { + struct fsl_upm upm; + + int width; + int upm_cmd_offset; + int upm_addr_offset; + int upm_mar_chip_offset; + int wait_flags; + int (*dev_ready)(int chip_nr); + int chip_delay; + int chip_offset; + int chip_nr; + + /* no need to fill */ + int last_ctrl; +}; + +extern int fsl_upm_nand_init(struct nand_chip *chip, struct fsl_upm_nand *fun); + +#endif diff --git a/roms/u-boot/include/linux/mtd/fsmc_nand.h b/roms/u-boot/include/linux/mtd/fsmc_nand.h new file mode 100644 index 000000000..6079f9e26 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/fsmc_nand.h @@ -0,0 +1,84 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2010 + * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. + */ + +#ifndef __FSMC_NAND_H__ +#define __FSMC_NAND_H__ + +#include <linux/mtd/rawnand.h> + +struct fsmc_regs { + u32 ctrl; /* 0x00 */ + u8 reserved_1[0x40 - 0x04]; + u32 pc; /* 0x40 */ + u32 sts; /* 0x44 */ + u32 comm; /* 0x48 */ + u32 attrib; /* 0x4c */ + u32 ioata; /* 0x50 */ + u32 ecc1; /* 0x54 */ + u32 ecc2; /* 0x58 */ + u32 ecc3; /* 0x5c */ + u8 reserved_2[0xfe0 - 0x60]; + u32 peripid0; /* 0xfe0 */ + u32 peripid1; /* 0xfe4 */ + u32 peripid2; /* 0xfe8 */ + u32 peripid3; /* 0xfec */ + u32 pcellid0; /* 0xff0 */ + u32 pcellid1; /* 0xff4 */ + u32 pcellid2; /* 0xff8 */ + u32 pcellid3; /* 0xffc */ +}; + +/* ctrl register definitions */ +#define FSMC_WP (1 << 7) + +/* pc register definitions */ +#define FSMC_RESET (1 << 0) +#define FSMC_WAITON (1 << 1) +#define FSMC_ENABLE (1 << 2) +#define FSMC_DEVTYPE_NAND (1 << 3) +#define FSMC_DEVWID_8 (0 << 4) +#define FSMC_DEVWID_16 (1 << 4) +#define FSMC_ECCEN (1 << 6) +#define FSMC_ECCPLEN_512 (0 << 7) +#define FSMC_ECCPLEN_256 (1 << 7) +#define FSMC_TCLR_1 (1 << 9) +#define FSMC_TAR_1 (1 << 13) + +/* sts register definitions */ +#define FSMC_CODE_RDY (1 << 15) + +/* comm register definitions */ +#define FSMC_TSET_0 (0 << 0) +#define FSMC_TWAIT_6 (6 << 8) +#define FSMC_THOLD_4 (4 << 16) +#define FSMC_THIZ_1 (1 << 24) + +/* peripid2 register definitions */ +#define FSMC_REVISION_MSK (0xf) +#define FSMC_REVISION_SHFT (0x4) + +#define FSMC_VER8 0x8 + +/* + * There are 13 bytes of ecc for every 512 byte block and it has to be read + * consecutively and immediately after the 512 byte data block for hardware to + * generate the error bit offsets + * Managing the ecc bytes in the following way is easier. This way is similar to + * oobfree structure maintained already in u-boot nand driver + */ +#define FSMC_MAX_ECCPLACE_ENTRIES 32 + +struct fsmc_nand_eccplace { + u32 offset; + u32 length; +}; + +struct fsmc_eccplace { + struct fsmc_nand_eccplace eccplace[FSMC_MAX_ECCPLACE_ENTRIES]; +}; + +extern int fsmc_nand_init(struct nand_chip *nand); +#endif diff --git a/roms/u-boot/include/linux/mtd/mtd.h b/roms/u-boot/include/linux/mtd/mtd.h new file mode 100644 index 000000000..927854950 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/mtd.h @@ -0,0 +1,601 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright © 1999-2010 David Woodhouse <dwmw2@infradead.org> et al. + * + */ + +#ifndef __MTD_MTD_H__ +#define __MTD_MTD_H__ + +#ifndef __UBOOT__ +#include <linux/types.h> +#include <linux/uio.h> +#include <linux/notifier.h> +#include <linux/device.h> + +#include <mtd/mtd-abi.h> + +#include <asm/div64.h> +#else +#include <linux/compat.h> +#include <mtd/mtd-abi.h> +#include <linux/errno.h> +#include <linux/list.h> +#include <div64.h> +#if IS_ENABLED(CONFIG_DM) +#include <dm/device.h> +#endif + +#define MAX_MTD_DEVICES 32 +#endif + +#define MTD_ERASE_PENDING 0x01 +#define MTD_ERASING 0x02 +#define MTD_ERASE_SUSPEND 0x04 +#define MTD_ERASE_DONE 0x08 +#define MTD_ERASE_FAILED 0x10 + +#define MTD_FAIL_ADDR_UNKNOWN -1LL + +/* + * If the erase fails, fail_addr might indicate exactly which block failed. If + * fail_addr = MTD_FAIL_ADDR_UNKNOWN, the failure was not at the device level + * or was not specific to any particular block. + */ +struct erase_info { + struct mtd_info *mtd; + uint64_t addr; + uint64_t len; + uint64_t fail_addr; + u_long time; + u_long retries; + unsigned dev; + unsigned cell; + void (*callback) (struct erase_info *self); + u_long priv; + u_char state; + struct erase_info *next; + int scrub; +}; + +struct mtd_erase_region_info { + uint64_t offset; /* At which this region starts, from the beginning of the MTD */ + uint32_t erasesize; /* For this region */ + uint32_t numblocks; /* Number of blocks of erasesize in this region */ + unsigned long *lockmap; /* If keeping bitmap of locks */ +}; + +/** + * struct mtd_oob_ops - oob operation operands + * @mode: operation mode + * + * @len: number of data bytes to write/read + * + * @retlen: number of data bytes written/read + * + * @ooblen: number of oob bytes to write/read + * @oobretlen: number of oob bytes written/read + * @ooboffs: offset of oob data in the oob area (only relevant when + * mode = MTD_OPS_PLACE_OOB or MTD_OPS_RAW) + * @datbuf: data buffer - if NULL only oob data are read/written + * @oobbuf: oob data buffer + */ +struct mtd_oob_ops { + unsigned int mode; + size_t len; + size_t retlen; + size_t ooblen; + size_t oobretlen; + uint32_t ooboffs; + uint8_t *datbuf; + uint8_t *oobbuf; +}; + +#ifdef CONFIG_SYS_NAND_MAX_OOBFREE +#define MTD_MAX_OOBFREE_ENTRIES_LARGE CONFIG_SYS_NAND_MAX_OOBFREE +#else +#define MTD_MAX_OOBFREE_ENTRIES_LARGE 32 +#endif + +#ifdef CONFIG_SYS_NAND_MAX_ECCPOS +#define MTD_MAX_ECCPOS_ENTRIES_LARGE CONFIG_SYS_NAND_MAX_ECCPOS +#else +#define MTD_MAX_ECCPOS_ENTRIES_LARGE 680 +#endif +/** + * struct mtd_oob_region - oob region definition + * @offset: region offset + * @length: region length + * + * This structure describes a region of the OOB area, and is used + * to retrieve ECC or free bytes sections. + * Each section is defined by an offset within the OOB area and a + * length. + */ +struct mtd_oob_region { + u32 offset; + u32 length; +}; + +/* + * struct mtd_ooblayout_ops - NAND OOB layout operations + * @ecc: function returning an ECC region in the OOB area. + * Should return -ERANGE if %section exceeds the total number of + * ECC sections. + * @free: function returning a free region in the OOB area. + * Should return -ERANGE if %section exceeds the total number of + * free sections. + */ +struct mtd_ooblayout_ops { + int (*ecc)(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobecc); + int (*rfree)(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobfree); +}; + +/* + * Internal ECC layout control structure. For historical reasons, there is a + * similar, smaller struct nand_ecclayout_user (in mtd-abi.h) that is retained + * for export to user-space via the ECCGETLAYOUT ioctl. + * nand_ecclayout should be expandable in the future simply by the above macros. + */ +struct nand_ecclayout { + __u32 eccbytes; + __u32 eccpos[MTD_MAX_ECCPOS_ENTRIES_LARGE]; + __u32 oobavail; + struct nand_oobfree oobfree[MTD_MAX_OOBFREE_ENTRIES_LARGE]; +}; + +struct module; /* only needed for owner field in mtd_info */ + +struct mtd_info { + u_char type; + uint32_t flags; + uint64_t size; // Total size of the MTD + + /* "Major" erase size for the device. Naïve users may take this + * to be the only erase size available, or may use the more detailed + * information below if they desire + */ + uint32_t erasesize; + /* Minimal writable flash unit size. In case of NOR flash it is 1 (even + * though individual bits can be cleared), in case of NAND flash it is + * one NAND page (or half, or one-fourths of it), in case of ECC-ed NOR + * it is of ECC block size, etc. It is illegal to have writesize = 0. + * Any driver registering a struct mtd_info must ensure a writesize of + * 1 or larger. + */ + uint32_t writesize; + + /* + * Size of the write buffer used by the MTD. MTD devices having a write + * buffer can write multiple writesize chunks at a time. E.g. while + * writing 4 * writesize bytes to a device with 2 * writesize bytes + * buffer the MTD driver can (but doesn't have to) do 2 writesize + * operations, but not 4. Currently, all NANDs have writebufsize + * equivalent to writesize (NAND page size). Some NOR flashes do have + * writebufsize greater than writesize. + */ + uint32_t writebufsize; + + uint32_t oobsize; // Amount of OOB data per block (e.g. 16) + uint32_t oobavail; // Available OOB bytes per block + + /* + * If erasesize is a power of 2 then the shift is stored in + * erasesize_shift otherwise erasesize_shift is zero. Ditto writesize. + */ + unsigned int erasesize_shift; + unsigned int writesize_shift; + /* Masks based on erasesize_shift and writesize_shift */ + unsigned int erasesize_mask; + unsigned int writesize_mask; + + /* + * read ops return -EUCLEAN if max number of bitflips corrected on any + * one region comprising an ecc step equals or exceeds this value. + * Settable by driver, else defaults to ecc_strength. User can override + * in sysfs. N.B. The meaning of the -EUCLEAN return code has changed; + * see Documentation/ABI/testing/sysfs-class-mtd for more detail. + */ + unsigned int bitflip_threshold; + + // Kernel-only stuff starts here. +#ifndef __UBOOT__ + const char *name; +#else + char *name; +#endif + int index; + + /* OOB layout description */ + const struct mtd_ooblayout_ops *ooblayout; + + /* ECC layout structure pointer - read only! */ + struct nand_ecclayout *ecclayout; + + /* the ecc step size. */ + unsigned int ecc_step_size; + + /* max number of correctible bit errors per ecc step */ + unsigned int ecc_strength; + + /* Data for variable erase regions. If numeraseregions is zero, + * it means that the whole device has erasesize as given above. + */ + int numeraseregions; + struct mtd_erase_region_info *eraseregions; + + /* + * Do not call via these pointers, use corresponding mtd_*() + * wrappers instead. + */ + int (*_erase) (struct mtd_info *mtd, struct erase_info *instr); +#ifndef __UBOOT__ + int (*_point) (struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, void **virt, resource_size_t *phys); + int (*_unpoint) (struct mtd_info *mtd, loff_t from, size_t len); +#endif + unsigned long (*_get_unmapped_area) (struct mtd_info *mtd, + unsigned long len, + unsigned long offset, + unsigned long flags); + int (*_read) (struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf); + int (*_write) (struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf); + int (*_panic_write) (struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf); + int (*_read_oob) (struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops); + int (*_write_oob) (struct mtd_info *mtd, loff_t to, + struct mtd_oob_ops *ops); + int (*_get_fact_prot_info) (struct mtd_info *mtd, size_t len, + size_t *retlen, struct otp_info *buf); + int (*_read_fact_prot_reg) (struct mtd_info *mtd, loff_t from, + size_t len, size_t *retlen, u_char *buf); + int (*_get_user_prot_info) (struct mtd_info *mtd, size_t len, + size_t *retlen, struct otp_info *buf); + int (*_read_user_prot_reg) (struct mtd_info *mtd, loff_t from, + size_t len, size_t *retlen, u_char *buf); + int (*_write_user_prot_reg) (struct mtd_info *mtd, loff_t to, + size_t len, size_t *retlen, u_char *buf); + int (*_lock_user_prot_reg) (struct mtd_info *mtd, loff_t from, + size_t len); +#ifndef __UBOOT__ + int (*_writev) (struct mtd_info *mtd, const struct kvec *vecs, + unsigned long count, loff_t to, size_t *retlen); +#endif + void (*_sync) (struct mtd_info *mtd); + int (*_lock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); + int (*_unlock) (struct mtd_info *mtd, loff_t ofs, uint64_t len); + int (*_is_locked) (struct mtd_info *mtd, loff_t ofs, uint64_t len); + int (*_block_isreserved) (struct mtd_info *mtd, loff_t ofs); + int (*_block_isbad) (struct mtd_info *mtd, loff_t ofs); + int (*_block_markbad) (struct mtd_info *mtd, loff_t ofs); +#ifndef __UBOOT__ + int (*_suspend) (struct mtd_info *mtd); + void (*_resume) (struct mtd_info *mtd); + void (*_reboot) (struct mtd_info *mtd); +#endif + /* + * If the driver is something smart, like UBI, it may need to maintain + * its own reference counting. The below functions are only for driver. + */ + int (*_get_device) (struct mtd_info *mtd); + void (*_put_device) (struct mtd_info *mtd); + +#ifndef __UBOOT__ + /* Backing device capabilities for this device + * - provides mmap capabilities + */ + struct backing_dev_info *backing_dev_info; + + struct notifier_block reboot_notifier; /* default mode before reboot */ +#endif + + /* ECC status information */ + struct mtd_ecc_stats ecc_stats; + /* Subpage shift (NAND) */ + int subpage_sft; + + void *priv; + + struct module *owner; +#ifndef __UBOOT__ + struct device dev; +#else + struct udevice *dev; +#endif + int usecount; + + /* MTD devices do not have any parent. MTD partitions do. */ + struct mtd_info *parent; + + /* + * Offset of the partition relatively to the parent offset. + * Is 0 for real MTD devices (ie. not partitions). + */ + u64 offset; + + /* + * List node used to add an MTD partition to the parent + * partition list. + */ + struct list_head node; + + /* + * List of partitions attached to this MTD device (the parent + * MTD device can itself be a partition). + */ + struct list_head partitions; +}; + +#if IS_ENABLED(CONFIG_DM) +static inline void mtd_set_ofnode(struct mtd_info *mtd, ofnode node) +{ + dev_set_ofnode(mtd->dev, node); +} + +static inline const ofnode mtd_get_ofnode(struct mtd_info *mtd) +{ + return dev_ofnode(mtd->dev); +} +#else +struct device_node; + +static inline void mtd_set_of_node(struct mtd_info *mtd, + const struct device_node *np) +{ +} + +static inline const struct device_node *mtd_get_of_node(struct mtd_info *mtd) +{ + return NULL; +} +#endif + +static inline bool mtd_is_partition(const struct mtd_info *mtd) +{ + return mtd->parent; +} + +static inline bool mtd_has_partitions(const struct mtd_info *mtd) +{ + return !list_empty(&mtd->partitions); +} + +bool mtd_partitions_used(struct mtd_info *master); + +int mtd_ooblayout_ecc(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobecc); +int mtd_ooblayout_find_eccregion(struct mtd_info *mtd, int eccbyte, + int *section, + struct mtd_oob_region *oobregion); +int mtd_ooblayout_get_eccbytes(struct mtd_info *mtd, u8 *eccbuf, + const u8 *oobbuf, int start, int nbytes); +int mtd_ooblayout_set_eccbytes(struct mtd_info *mtd, const u8 *eccbuf, + u8 *oobbuf, int start, int nbytes); +int mtd_ooblayout_free(struct mtd_info *mtd, int section, + struct mtd_oob_region *oobfree); +int mtd_ooblayout_get_databytes(struct mtd_info *mtd, u8 *databuf, + const u8 *oobbuf, int start, int nbytes); +int mtd_ooblayout_set_databytes(struct mtd_info *mtd, const u8 *databuf, + u8 *oobbuf, int start, int nbytes); +int mtd_ooblayout_count_freebytes(struct mtd_info *mtd); +int mtd_ooblayout_count_eccbytes(struct mtd_info *mtd); + +static inline void mtd_set_ooblayout(struct mtd_info *mtd, + const struct mtd_ooblayout_ops *ooblayout) +{ + mtd->ooblayout = ooblayout; +} + +static inline u32 mtd_oobavail(struct mtd_info *mtd, struct mtd_oob_ops *ops) +{ + return ops->mode == MTD_OPS_AUTO_OOB ? mtd->oobavail : mtd->oobsize; +} + +int mtd_erase(struct mtd_info *mtd, struct erase_info *instr); +#ifndef __UBOOT__ +int mtd_point(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, + void **virt, resource_size_t *phys); +int mtd_unpoint(struct mtd_info *mtd, loff_t from, size_t len); +#endif +unsigned long mtd_get_unmapped_area(struct mtd_info *mtd, unsigned long len, + unsigned long offset, unsigned long flags); +int mtd_read(struct mtd_info *mtd, loff_t from, size_t len, size_t *retlen, + u_char *buf); +int mtd_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, + const u_char *buf); +int mtd_panic_write(struct mtd_info *mtd, loff_t to, size_t len, size_t *retlen, + const u_char *buf); + +int mtd_read_oob(struct mtd_info *mtd, loff_t from, struct mtd_oob_ops *ops); +int mtd_write_oob(struct mtd_info *mtd, loff_t to, struct mtd_oob_ops *ops); + +int mtd_get_fact_prot_info(struct mtd_info *mtd, size_t len, size_t *retlen, + struct otp_info *buf); +int mtd_read_fact_prot_reg(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf); +int mtd_get_user_prot_info(struct mtd_info *mtd, size_t len, size_t *retlen, + struct otp_info *buf); +int mtd_read_user_prot_reg(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf); +int mtd_write_user_prot_reg(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, u_char *buf); +int mtd_lock_user_prot_reg(struct mtd_info *mtd, loff_t from, size_t len); + +#ifndef __UBOOT__ +int mtd_writev(struct mtd_info *mtd, const struct kvec *vecs, + unsigned long count, loff_t to, size_t *retlen); +#endif + +static inline void mtd_sync(struct mtd_info *mtd) +{ + if (mtd->_sync) + mtd->_sync(mtd); +} + +int mtd_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len); +int mtd_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len); +int mtd_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len); +int mtd_block_isreserved(struct mtd_info *mtd, loff_t ofs); +int mtd_block_isbad(struct mtd_info *mtd, loff_t ofs); +int mtd_block_markbad(struct mtd_info *mtd, loff_t ofs); + +#ifndef __UBOOT__ +static inline int mtd_suspend(struct mtd_info *mtd) +{ + return mtd->_suspend ? mtd->_suspend(mtd) : 0; +} + +static inline void mtd_resume(struct mtd_info *mtd) +{ + if (mtd->_resume) + mtd->_resume(mtd); +} +#endif + +static inline uint32_t mtd_div_by_eb(uint64_t sz, struct mtd_info *mtd) +{ + if (mtd->erasesize_shift) + return sz >> mtd->erasesize_shift; + do_div(sz, mtd->erasesize); + return sz; +} + +static inline uint32_t mtd_mod_by_eb(uint64_t sz, struct mtd_info *mtd) +{ + if (mtd->erasesize_shift) + return sz & mtd->erasesize_mask; + return do_div(sz, mtd->erasesize); +} + +static inline uint32_t mtd_div_by_ws(uint64_t sz, struct mtd_info *mtd) +{ + if (mtd->writesize_shift) + return sz >> mtd->writesize_shift; + do_div(sz, mtd->writesize); + return sz; +} + +static inline uint32_t mtd_mod_by_ws(uint64_t sz, struct mtd_info *mtd) +{ + if (mtd->writesize_shift) + return sz & mtd->writesize_mask; + return do_div(sz, mtd->writesize); +} + +static inline int mtd_has_oob(const struct mtd_info *mtd) +{ + return mtd->_read_oob && mtd->_write_oob; +} + +static inline int mtd_type_is_nand(const struct mtd_info *mtd) +{ + return mtd->type == MTD_NANDFLASH || mtd->type == MTD_MLCNANDFLASH; +} + +static inline int mtd_can_have_bb(const struct mtd_info *mtd) +{ + return !!mtd->_block_isbad; +} + + /* Kernel-side ioctl definitions */ + +struct mtd_partition; +struct mtd_part_parser_data; + +extern int mtd_device_parse_register(struct mtd_info *mtd, + const char * const *part_probe_types, + struct mtd_part_parser_data *parser_data, + const struct mtd_partition *defparts, + int defnr_parts); +#define mtd_device_register(master, parts, nr_parts) \ + mtd_device_parse_register(master, NULL, NULL, parts, nr_parts) +extern int mtd_device_unregister(struct mtd_info *master); +extern struct mtd_info *get_mtd_device(struct mtd_info *mtd, int num); +extern int __get_mtd_device(struct mtd_info *mtd); +extern void __put_mtd_device(struct mtd_info *mtd); +extern struct mtd_info *get_mtd_device_nm(const char *name); +extern void put_mtd_device(struct mtd_info *mtd); + + +#ifndef __UBOOT__ +struct mtd_notifier { + void (*add)(struct mtd_info *mtd); + void (*remove)(struct mtd_info *mtd); + struct list_head list; +}; + + +extern void register_mtd_user (struct mtd_notifier *new); +extern int unregister_mtd_user (struct mtd_notifier *old); +#endif +void *mtd_kmalloc_up_to(const struct mtd_info *mtd, size_t *size); + +#ifdef CONFIG_MTD_PARTITIONS +void mtd_erase_callback(struct erase_info *instr); +#else +static inline void mtd_erase_callback(struct erase_info *instr) +{ + if (instr->callback) + instr->callback(instr); +} +#endif + +static inline int mtd_is_bitflip(int err) { + return err == -EUCLEAN; +} + +static inline int mtd_is_eccerr(int err) { + return err == -EBADMSG; +} + +static inline int mtd_is_bitflip_or_eccerr(int err) { + return mtd_is_bitflip(err) || mtd_is_eccerr(err); +} + +unsigned mtd_mmap_capabilities(struct mtd_info *mtd); + +#ifdef __UBOOT__ +/* drivers/mtd/mtdcore.h */ +int add_mtd_device(struct mtd_info *mtd); +int del_mtd_device(struct mtd_info *mtd); + +#ifdef CONFIG_MTD_PARTITIONS +int add_mtd_partitions(struct mtd_info *, const struct mtd_partition *, int); +int del_mtd_partitions(struct mtd_info *); +#else +static inline int add_mtd_partitions(struct mtd_info *mtd, + const struct mtd_partition *parts, + int nparts) +{ + return 0; +} + +static inline int del_mtd_partitions(struct mtd_info *mtd) +{ + return 0; +} +#endif + +struct mtd_info *__mtd_next_device(int i); +#define mtd_for_each_device(mtd) \ + for ((mtd) = __mtd_next_device(0); \ + (mtd) != NULL; \ + (mtd) = __mtd_next_device(mtd->index + 1)) + +/* drivers/mtd/mtdcore.c */ +void mtd_get_len_incl_bad(struct mtd_info *mtd, uint64_t offset, + const uint64_t length, uint64_t *len_incl_bad, + int *truncated); +bool mtd_dev_list_updated(void); + +/* drivers/mtd/mtd_uboot.c */ +int mtd_search_alternate_name(const char *mtdname, char *altname, + unsigned int max_len); + +#endif +#endif /* __MTD_MTD_H__ */ diff --git a/roms/u-boot/include/linux/mtd/nand.h b/roms/u-boot/include/linux/mtd/nand.h new file mode 100644 index 000000000..7774c17ad --- /dev/null +++ b/roms/u-boot/include/linux/mtd/nand.h @@ -0,0 +1,748 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright 2017 - Free Electrons + * + * Authors: + * Boris Brezillon <boris.brezillon@free-electrons.com> + * Peter Pan <peterpandong@micron.com> + */ + +#ifndef __LINUX_MTD_NAND_H +#define __LINUX_MTD_NAND_H + +#include <linux/mtd/mtd.h> + +/** + * struct nand_memory_organization - Memory organization structure + * @bits_per_cell: number of bits per NAND cell + * @pagesize: page size + * @oobsize: OOB area size + * @pages_per_eraseblock: number of pages per eraseblock + * @eraseblocks_per_lun: number of eraseblocks per LUN (Logical Unit Number) + * @planes_per_lun: number of planes per LUN + * @luns_per_target: number of LUN per target (target is a synonym for die) + * @ntargets: total number of targets exposed by the NAND device + */ +struct nand_memory_organization { + unsigned int bits_per_cell; + unsigned int pagesize; + unsigned int oobsize; + unsigned int pages_per_eraseblock; + unsigned int eraseblocks_per_lun; + unsigned int planes_per_lun; + unsigned int luns_per_target; + unsigned int ntargets; +}; + +#define NAND_MEMORG(bpc, ps, os, ppe, epl, ppl, lpt, nt) \ + { \ + .bits_per_cell = (bpc), \ + .pagesize = (ps), \ + .oobsize = (os), \ + .pages_per_eraseblock = (ppe), \ + .eraseblocks_per_lun = (epl), \ + .planes_per_lun = (ppl), \ + .luns_per_target = (lpt), \ + .ntargets = (nt), \ + } + +/** + * struct nand_row_converter - Information needed to convert an absolute offset + * into a row address + * @lun_addr_shift: position of the LUN identifier in the row address + * @eraseblock_addr_shift: position of the eraseblock identifier in the row + * address + */ +struct nand_row_converter { + unsigned int lun_addr_shift; + unsigned int eraseblock_addr_shift; +}; + +/** + * struct nand_pos - NAND position object + * @target: the NAND target/die + * @lun: the LUN identifier + * @plane: the plane within the LUN + * @eraseblock: the eraseblock within the LUN + * @page: the page within the LUN + * + * These information are usually used by specific sub-layers to select the + * appropriate target/die and generate a row address to pass to the device. + */ +struct nand_pos { + unsigned int target; + unsigned int lun; + unsigned int plane; + unsigned int eraseblock; + unsigned int page; +}; + +/** + * struct nand_page_io_req - NAND I/O request object + * @pos: the position this I/O request is targeting + * @dataoffs: the offset within the page + * @datalen: number of data bytes to read from/write to this page + * @databuf: buffer to store data in or get data from + * @ooboffs: the OOB offset within the page + * @ooblen: the number of OOB bytes to read from/write to this page + * @oobbuf: buffer to store OOB data in or get OOB data from + * @mode: one of the %MTD_OPS_XXX mode + * + * This object is used to pass per-page I/O requests to NAND sub-layers. This + * way all useful information are already formatted in a useful way and + * specific NAND layers can focus on translating these information into + * specific commands/operations. + */ +struct nand_page_io_req { + struct nand_pos pos; + unsigned int dataoffs; + unsigned int datalen; + union { + const void *out; + void *in; + } databuf; + unsigned int ooboffs; + unsigned int ooblen; + union { + const void *out; + void *in; + } oobbuf; + int mode; +}; + +/** + * struct nand_ecc_req - NAND ECC requirements + * @strength: ECC strength + * @step_size: ECC step/block size + */ +struct nand_ecc_req { + unsigned int strength; + unsigned int step_size; +}; + +#define NAND_ECCREQ(str, stp) { .strength = (str), .step_size = (stp) } + +/** + * struct nand_bbt - bad block table object + * @cache: in memory BBT cache + */ +struct nand_bbt { + unsigned long *cache; +}; + +struct nand_device; + +/** + * struct nand_ops - NAND operations + * @erase: erase a specific block. No need to check if the block is bad before + * erasing, this has been taken care of by the generic NAND layer + * @markbad: mark a specific block bad. No need to check if the block is + * already marked bad, this has been taken care of by the generic + * NAND layer. This method should just write the BBM (Bad Block + * Marker) so that future call to struct_nand_ops->isbad() return + * true + * @isbad: check whether a block is bad or not. This method should just read + * the BBM and return whether the block is bad or not based on what it + * reads + * + * These are all low level operations that should be implemented by specialized + * NAND layers (SPI NAND, raw NAND, ...). + */ +struct nand_ops { + int (*erase)(struct nand_device *nand, const struct nand_pos *pos); + int (*markbad)(struct nand_device *nand, const struct nand_pos *pos); + bool (*isbad)(struct nand_device *nand, const struct nand_pos *pos); +}; + +/** + * struct nand_device - NAND device + * @mtd: MTD instance attached to the NAND device + * @memorg: memory layout + * @eccreq: ECC requirements + * @rowconv: position to row address converter + * @bbt: bad block table info + * @ops: NAND operations attached to the NAND device + * + * Generic NAND object. Specialized NAND layers (raw NAND, SPI NAND, OneNAND) + * should declare their own NAND object embedding a nand_device struct (that's + * how inheritance is done). + * struct_nand_device->memorg and struct_nand_device->eccreq should be filled + * at device detection time to reflect the NAND device + * capabilities/requirements. Once this is done nanddev_init() can be called. + * It will take care of converting NAND information into MTD ones, which means + * the specialized NAND layers should never manually tweak + * struct_nand_device->mtd except for the ->_read/write() hooks. + */ +struct nand_device { + struct mtd_info *mtd; + struct nand_memory_organization memorg; + struct nand_ecc_req eccreq; + struct nand_row_converter rowconv; + struct nand_bbt bbt; + const struct nand_ops *ops; +}; + +/** + * struct nand_io_iter - NAND I/O iterator + * @req: current I/O request + * @oobbytes_per_page: maximum number of OOB bytes per page + * @dataleft: remaining number of data bytes to read/write + * @oobleft: remaining number of OOB bytes to read/write + * + * Can be used by specialized NAND layers to iterate over all pages covered + * by an MTD I/O request, which should greatly simplifies the boiler-plate + * code needed to read/write data from/to a NAND device. + */ +struct nand_io_iter { + struct nand_page_io_req req; + unsigned int oobbytes_per_page; + unsigned int dataleft; + unsigned int oobleft; +}; + +/** + * mtd_to_nanddev() - Get the NAND device attached to the MTD instance + * @mtd: MTD instance + * + * Return: the NAND device embedding @mtd. + */ +static inline struct nand_device *mtd_to_nanddev(struct mtd_info *mtd) +{ + return mtd->priv; +} + +/** + * nanddev_to_mtd() - Get the MTD device attached to a NAND device + * @nand: NAND device + * + * Return: the MTD device embedded in @nand. + */ +static inline struct mtd_info *nanddev_to_mtd(struct nand_device *nand) +{ + return nand->mtd; +} + +/* + * nanddev_bits_per_cell() - Get the number of bits per cell + * @nand: NAND device + * + * Return: the number of bits per cell. + */ +static inline unsigned int nanddev_bits_per_cell(const struct nand_device *nand) +{ + return nand->memorg.bits_per_cell; +} + +/** + * nanddev_page_size() - Get NAND page size + * @nand: NAND device + * + * Return: the page size. + */ +static inline size_t nanddev_page_size(const struct nand_device *nand) +{ + return nand->memorg.pagesize; +} + +/** + * nanddev_per_page_oobsize() - Get NAND OOB size + * @nand: NAND device + * + * Return: the OOB size. + */ +static inline unsigned int +nanddev_per_page_oobsize(const struct nand_device *nand) +{ + return nand->memorg.oobsize; +} + +/** + * nanddev_pages_per_eraseblock() - Get the number of pages per eraseblock + * @nand: NAND device + * + * Return: the number of pages per eraseblock. + */ +static inline unsigned int +nanddev_pages_per_eraseblock(const struct nand_device *nand) +{ + return nand->memorg.pages_per_eraseblock; +} + +/** + * nanddev_per_page_oobsize() - Get NAND erase block size + * @nand: NAND device + * + * Return: the eraseblock size. + */ +static inline size_t nanddev_eraseblock_size(const struct nand_device *nand) +{ + return nand->memorg.pagesize * nand->memorg.pages_per_eraseblock; +} + +/** + * nanddev_eraseblocks_per_lun() - Get the number of eraseblocks per LUN + * @nand: NAND device + * + * Return: the number of eraseblocks per LUN. + */ +static inline unsigned int +nanddev_eraseblocks_per_lun(const struct nand_device *nand) +{ + return nand->memorg.eraseblocks_per_lun; +} + +/** + * nanddev_target_size() - Get the total size provided by a single target/die + * @nand: NAND device + * + * Return: the total size exposed by a single target/die in bytes. + */ +static inline u64 nanddev_target_size(const struct nand_device *nand) +{ + return (u64)nand->memorg.luns_per_target * + nand->memorg.eraseblocks_per_lun * + nand->memorg.pages_per_eraseblock * + nand->memorg.pagesize; +} + +/** + * nanddev_ntarget() - Get the total of targets + * @nand: NAND device + * + * Return: the number of targets/dies exposed by @nand. + */ +static inline unsigned int nanddev_ntargets(const struct nand_device *nand) +{ + return nand->memorg.ntargets; +} + +/** + * nanddev_neraseblocks() - Get the total number of erasablocks + * @nand: NAND device + * + * Return: the total number of eraseblocks exposed by @nand. + */ +static inline unsigned int nanddev_neraseblocks(const struct nand_device *nand) +{ + return (u64)nand->memorg.luns_per_target * + nand->memorg.eraseblocks_per_lun * + nand->memorg.pages_per_eraseblock; +} + +/** + * nanddev_size() - Get NAND size + * @nand: NAND device + * + * Return: the total size (in bytes) exposed by @nand. + */ +static inline u64 nanddev_size(const struct nand_device *nand) +{ + return nanddev_target_size(nand) * nanddev_ntargets(nand); +} + +/** + * nanddev_get_memorg() - Extract memory organization info from a NAND device + * @nand: NAND device + * + * This can be used by the upper layer to fill the memorg info before calling + * nanddev_init(). + * + * Return: the memorg object embedded in the NAND device. + */ +static inline struct nand_memory_organization * +nanddev_get_memorg(struct nand_device *nand) +{ + return &nand->memorg; +} + +int nanddev_init(struct nand_device *nand, const struct nand_ops *ops, + struct module *owner); +void nanddev_cleanup(struct nand_device *nand); + +/** + * nanddev_register() - Register a NAND device + * @nand: NAND device + * + * Register a NAND device. + * This function is just a wrapper around mtd_device_register() + * registering the MTD device embedded in @nand. + * + * Return: 0 in case of success, a negative error code otherwise. + */ +static inline int nanddev_register(struct nand_device *nand) +{ + return mtd_device_register(nand->mtd, NULL, 0); +} + +/** + * nanddev_unregister() - Unregister a NAND device + * @nand: NAND device + * + * Unregister a NAND device. + * This function is just a wrapper around mtd_device_unregister() + * unregistering the MTD device embedded in @nand. + * + * Return: 0 in case of success, a negative error code otherwise. + */ +static inline int nanddev_unregister(struct nand_device *nand) +{ + return mtd_device_unregister(nand->mtd); +} + +#ifndef __UBOOT__ +/** + * nanddev_set_of_node() - Attach a DT node to a NAND device + * @nand: NAND device + * @np: DT node + * + * Attach a DT node to a NAND device. + */ +static inline void nanddev_set_of_node(struct nand_device *nand, + const struct device_node *np) +{ + mtd_set_of_node(nand->mtd, np); +} + +/** + * nanddev_get_of_node() - Retrieve the DT node attached to a NAND device + * @nand: NAND device + * + * Return: the DT node attached to @nand. + */ +static inline const struct device_node *nanddev_get_of_node(struct nand_device *nand) +{ + return mtd_get_of_node(nand->mtd); +} +#else +/** + * nanddev_set_of_node() - Attach a DT node to a NAND device + * @nand: NAND device + * @node: ofnode + * + * Attach a DT node to a NAND device. + */ +static inline void nanddev_set_ofnode(struct nand_device *nand, ofnode node) +{ + mtd_set_ofnode(nand->mtd, node); +} +#endif /* __UBOOT__ */ + +/** + * nanddev_offs_to_pos() - Convert an absolute NAND offset into a NAND position + * @nand: NAND device + * @offs: absolute NAND offset (usually passed by the MTD layer) + * @pos: a NAND position object to fill in + * + * Converts @offs into a nand_pos representation. + * + * Return: the offset within the NAND page pointed by @pos. + */ +static inline unsigned int nanddev_offs_to_pos(struct nand_device *nand, + loff_t offs, + struct nand_pos *pos) +{ + unsigned int pageoffs; + u64 tmp = offs; + + pageoffs = do_div(tmp, nand->memorg.pagesize); + pos->page = do_div(tmp, nand->memorg.pages_per_eraseblock); + pos->eraseblock = do_div(tmp, nand->memorg.eraseblocks_per_lun); + pos->plane = pos->eraseblock % nand->memorg.planes_per_lun; + pos->lun = do_div(tmp, nand->memorg.luns_per_target); + pos->target = tmp; + + return pageoffs; +} + +/** + * nanddev_pos_cmp() - Compare two NAND positions + * @a: First NAND position + * @b: Second NAND position + * + * Compares two NAND positions. + * + * Return: -1 if @a < @b, 0 if @a == @b and 1 if @a > @b. + */ +static inline int nanddev_pos_cmp(const struct nand_pos *a, + const struct nand_pos *b) +{ + if (a->target != b->target) + return a->target < b->target ? -1 : 1; + + if (a->lun != b->lun) + return a->lun < b->lun ? -1 : 1; + + if (a->eraseblock != b->eraseblock) + return a->eraseblock < b->eraseblock ? -1 : 1; + + if (a->page != b->page) + return a->page < b->page ? -1 : 1; + + return 0; +} + +/** + * nanddev_pos_to_offs() - Convert a NAND position into an absolute offset + * @nand: NAND device + * @pos: the NAND position to convert + * + * Converts @pos NAND position into an absolute offset. + * + * Return: the absolute offset. Note that @pos points to the beginning of a + * page, if one wants to point to a specific offset within this page + * the returned offset has to be adjusted manually. + */ +static inline loff_t nanddev_pos_to_offs(struct nand_device *nand, + const struct nand_pos *pos) +{ + unsigned int npages; + + npages = pos->page + + ((pos->eraseblock + + (pos->lun + + (pos->target * nand->memorg.luns_per_target)) * + nand->memorg.eraseblocks_per_lun) * + nand->memorg.pages_per_eraseblock); + + return (loff_t)npages * nand->memorg.pagesize; +} + +/** + * nanddev_pos_to_row() - Extract a row address from a NAND position + * @nand: NAND device + * @pos: the position to convert + * + * Converts a NAND position into a row address that can then be passed to the + * device. + * + * Return: the row address extracted from @pos. + */ +static inline unsigned int nanddev_pos_to_row(struct nand_device *nand, + const struct nand_pos *pos) +{ + return (pos->lun << nand->rowconv.lun_addr_shift) | + (pos->eraseblock << nand->rowconv.eraseblock_addr_shift) | + pos->page; +} + +/** + * nanddev_pos_next_target() - Move a position to the next target/die + * @nand: NAND device + * @pos: the position to update + * + * Updates @pos to point to the start of the next target/die. Useful when you + * want to iterate over all targets/dies of a NAND device. + */ +static inline void nanddev_pos_next_target(struct nand_device *nand, + struct nand_pos *pos) +{ + pos->page = 0; + pos->plane = 0; + pos->eraseblock = 0; + pos->lun = 0; + pos->target++; +} + +/** + * nanddev_pos_next_lun() - Move a position to the next LUN + * @nand: NAND device + * @pos: the position to update + * + * Updates @pos to point to the start of the next LUN. Useful when you want to + * iterate over all LUNs of a NAND device. + */ +static inline void nanddev_pos_next_lun(struct nand_device *nand, + struct nand_pos *pos) +{ + if (pos->lun >= nand->memorg.luns_per_target - 1) + return nanddev_pos_next_target(nand, pos); + + pos->lun++; + pos->page = 0; + pos->plane = 0; + pos->eraseblock = 0; +} + +/** + * nanddev_pos_next_eraseblock() - Move a position to the next eraseblock + * @nand: NAND device + * @pos: the position to update + * + * Updates @pos to point to the start of the next eraseblock. Useful when you + * want to iterate over all eraseblocks of a NAND device. + */ +static inline void nanddev_pos_next_eraseblock(struct nand_device *nand, + struct nand_pos *pos) +{ + if (pos->eraseblock >= nand->memorg.eraseblocks_per_lun - 1) + return nanddev_pos_next_lun(nand, pos); + + pos->eraseblock++; + pos->page = 0; + pos->plane = pos->eraseblock % nand->memorg.planes_per_lun; +} + +/** + * nanddev_pos_next_eraseblock() - Move a position to the next page + * @nand: NAND device + * @pos: the position to update + * + * Updates @pos to point to the start of the next page. Useful when you want to + * iterate over all pages of a NAND device. + */ +static inline void nanddev_pos_next_page(struct nand_device *nand, + struct nand_pos *pos) +{ + if (pos->page >= nand->memorg.pages_per_eraseblock - 1) + return nanddev_pos_next_eraseblock(nand, pos); + + pos->page++; +} + +/** + * nand_io_iter_init - Initialize a NAND I/O iterator + * @nand: NAND device + * @offs: absolute offset + * @req: MTD request + * @iter: NAND I/O iterator + * + * Initializes a NAND iterator based on the information passed by the MTD + * layer. + */ +static inline void nanddev_io_iter_init(struct nand_device *nand, + loff_t offs, struct mtd_oob_ops *req, + struct nand_io_iter *iter) +{ + struct mtd_info *mtd = nanddev_to_mtd(nand); + + iter->req.mode = req->mode; + iter->req.dataoffs = nanddev_offs_to_pos(nand, offs, &iter->req.pos); + iter->req.ooboffs = req->ooboffs; + iter->oobbytes_per_page = mtd_oobavail(mtd, req); + iter->dataleft = req->len; + iter->oobleft = req->ooblen; + iter->req.databuf.in = req->datbuf; + iter->req.datalen = min_t(unsigned int, + nand->memorg.pagesize - iter->req.dataoffs, + iter->dataleft); + iter->req.oobbuf.in = req->oobbuf; + iter->req.ooblen = min_t(unsigned int, + iter->oobbytes_per_page - iter->req.ooboffs, + iter->oobleft); +} + +/** + * nand_io_iter_next_page - Move to the next page + * @nand: NAND device + * @iter: NAND I/O iterator + * + * Updates the @iter to point to the next page. + */ +static inline void nanddev_io_iter_next_page(struct nand_device *nand, + struct nand_io_iter *iter) +{ + nanddev_pos_next_page(nand, &iter->req.pos); + iter->dataleft -= iter->req.datalen; + iter->req.databuf.in += iter->req.datalen; + iter->oobleft -= iter->req.ooblen; + iter->req.oobbuf.in += iter->req.ooblen; + iter->req.dataoffs = 0; + iter->req.ooboffs = 0; + iter->req.datalen = min_t(unsigned int, nand->memorg.pagesize, + iter->dataleft); + iter->req.ooblen = min_t(unsigned int, iter->oobbytes_per_page, + iter->oobleft); +} + +/** + * nand_io_iter_end - Should end iteration or not + * @nand: NAND device + * @iter: NAND I/O iterator + * + * Check whether @iter has reached the end of the NAND portion it was asked to + * iterate on or not. + * + * Return: true if @iter has reached the end of the iteration request, false + * otherwise. + */ +static inline bool nanddev_io_iter_end(struct nand_device *nand, + const struct nand_io_iter *iter) +{ + if (iter->dataleft || iter->oobleft) + return false; + + return true; +} + +/** + * nand_io_for_each_page - Iterate over all NAND pages contained in an MTD I/O + * request + * @nand: NAND device + * @start: start address to read/write from + * @req: MTD I/O request + * @iter: NAND I/O iterator + * + * Should be used for iterate over pages that are contained in an MTD request. + */ +#define nanddev_io_for_each_page(nand, start, req, iter) \ + for (nanddev_io_iter_init(nand, start, req, iter); \ + !nanddev_io_iter_end(nand, iter); \ + nanddev_io_iter_next_page(nand, iter)) + +bool nanddev_isbad(struct nand_device *nand, const struct nand_pos *pos); +bool nanddev_isreserved(struct nand_device *nand, const struct nand_pos *pos); +int nanddev_erase(struct nand_device *nand, const struct nand_pos *pos); +int nanddev_markbad(struct nand_device *nand, const struct nand_pos *pos); + +/* BBT related functions */ +enum nand_bbt_block_status { + NAND_BBT_BLOCK_STATUS_UNKNOWN, + NAND_BBT_BLOCK_GOOD, + NAND_BBT_BLOCK_WORN, + NAND_BBT_BLOCK_RESERVED, + NAND_BBT_BLOCK_FACTORY_BAD, + NAND_BBT_BLOCK_NUM_STATUS, +}; + +int nanddev_bbt_init(struct nand_device *nand); +void nanddev_bbt_cleanup(struct nand_device *nand); +int nanddev_bbt_update(struct nand_device *nand); +int nanddev_bbt_get_block_status(const struct nand_device *nand, + unsigned int entry); +int nanddev_bbt_set_block_status(struct nand_device *nand, unsigned int entry, + enum nand_bbt_block_status status); +int nanddev_bbt_markbad(struct nand_device *nand, unsigned int block); + +/** + * nanddev_bbt_pos_to_entry() - Convert a NAND position into a BBT entry + * @nand: NAND device + * @pos: the NAND position we want to get BBT entry for + * + * Return the BBT entry used to store information about the eraseblock pointed + * by @pos. + * + * Return: the BBT entry storing information about eraseblock pointed by @pos. + */ +static inline unsigned int nanddev_bbt_pos_to_entry(struct nand_device *nand, + const struct nand_pos *pos) +{ + return pos->eraseblock + + ((pos->lun + (pos->target * nand->memorg.luns_per_target)) * + nand->memorg.eraseblocks_per_lun); +} + +/** + * nanddev_bbt_is_initialized() - Check if the BBT has been initialized + * @nand: NAND device + * + * Return: true if the BBT has been initialized, false otherwise. + */ +static inline bool nanddev_bbt_is_initialized(struct nand_device *nand) +{ + return !!nand->bbt.cache; +} + +/* MTD -> NAND helper functions. */ +int nanddev_mtd_erase(struct mtd_info *mtd, struct erase_info *einfo); + +#endif /* __LINUX_MTD_NAND_H */ diff --git a/roms/u-boot/include/linux/mtd/nand_bch.h b/roms/u-boot/include/linux/mtd/nand_bch.h new file mode 100644 index 000000000..8ea6b04cc --- /dev/null +++ b/roms/u-boot/include/linux/mtd/nand_bch.h @@ -0,0 +1,68 @@ +/* + * Copyright © 2011 Ivan Djelic <ivan.djelic@parrot.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This file is the header for the NAND BCH ECC implementation. + */ + +#ifndef __MTD_NAND_BCH_H__ +#define __MTD_NAND_BCH_H__ + +struct mtd_info; +struct nand_bch_control; + +#if defined(CONFIG_NAND_ECC_BCH) + +static inline int mtd_nand_has_bch(void) { return 1; } + +/* + * Calculate BCH ecc code + */ +int nand_bch_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code); + +/* + * Detect and correct bit errors + */ +int nand_bch_correct_data(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, + u_char *calc_ecc); +/* + * Initialize BCH encoder/decoder + */ +struct nand_bch_control *nand_bch_init(struct mtd_info *mtd); +/* + * Release BCH encoder/decoder resources + */ +void nand_bch_free(struct nand_bch_control *nbc); + +#else /* !CONFIG_NAND_ECC_BCH */ + +static inline int mtd_nand_has_bch(void) { return 0; } + +static inline int +nand_bch_calculate_ecc(struct mtd_info *mtd, const u_char *dat, + u_char *ecc_code) +{ + return -1; +} + +static inline int +nand_bch_correct_data(struct mtd_info *mtd, unsigned char *buf, + unsigned char *read_ecc, unsigned char *calc_ecc) +{ + return -ENOTSUPP; +} + +static inline struct nand_bch_control *nand_bch_init(struct mtd_info *mtd) +{ + return NULL; +} + +static inline void nand_bch_free(struct nand_bch_control *nbc) {} + +#endif /* CONFIG_NAND_ECC_BCH */ + +#endif /* __MTD_NAND_BCH_H__ */ diff --git a/roms/u-boot/include/linux/mtd/nand_ecc.h b/roms/u-boot/include/linux/mtd/nand_ecc.h new file mode 100644 index 000000000..397836384 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/nand_ecc.h @@ -0,0 +1,27 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * drivers/mtd/nand_ecc.h + * + * Copyright (C) 2000-2010 Steven J. Hill <sjhill@realitydiluted.com> + * David Woodhouse <dwmw2@infradead.org> + * Thomas Gleixner <tglx@linutronix.de> + * + * This file is the header for the ECC algorithm. + */ + +#ifndef __MTD_NAND_ECC_H__ +#define __MTD_NAND_ECC_H__ + +struct mtd_info; + +/* + * Calculate 3 byte ECC code for 256 byte block + */ +int nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code); + +/* + * Detect and correct a 1 bit error for 256 byte block + */ +int nand_correct_data(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, u_char *calc_ecc); + +#endif /* __MTD_NAND_ECC_H__ */ diff --git a/roms/u-boot/include/linux/mtd/ndfc.h b/roms/u-boot/include/linux/mtd/ndfc.h new file mode 100644 index 000000000..d0558a982 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/ndfc.h @@ -0,0 +1,67 @@ +/* + * linux/include/linux/mtd/ndfc.h + * + * Copyright (c) 2006 Thomas Gleixner <tglx@linutronix.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Info: + * Contains defines, datastructures for ndfc nand controller + * + */ +#ifndef __LINUX_MTD_NDFC_H +#define __LINUX_MTD_NDFC_H + +/* NDFC Register definitions */ +#define NDFC_CMD 0x00 +#define NDFC_ALE 0x04 +#define NDFC_DATA 0x08 +#define NDFC_ECC 0x10 +#define NDFC_BCFG0 0x30 +#define NDFC_BCFG1 0x34 +#define NDFC_BCFG2 0x38 +#define NDFC_BCFG3 0x3c +#define NDFC_CCR 0x40 +#define NDFC_STAT 0x44 +#define NDFC_HWCTL 0x48 +#define NDFC_REVID 0x50 + +#define NDFC_STAT_IS_READY 0x01000000 + +#define NDFC_CCR_RESET_CE 0x80000000 /* CE Reset */ +#define NDFC_CCR_RESET_ECC 0x40000000 /* ECC Reset */ +#define NDFC_CCR_RIE 0x20000000 /* Interrupt Enable on Device Rdy */ +#define NDFC_CCR_REN 0x10000000 /* Enable wait for Rdy in LinearR */ +#define NDFC_CCR_ROMEN 0x08000000 /* Enable ROM In LinearR */ +#define NDFC_CCR_ARE 0x04000000 /* Auto-Read Enable */ +#define NDFC_CCR_BS(x) (((x) & 0x3) << 24) /* Select Bank on CE[x] */ +#define NDFC_CCR_BS_MASK 0x03000000 /* Select Bank */ +#define NDFC_CCR_ARAC0 0x00000000 /* 3 Addr, 1 Col 2 Row 512b page */ +#define NDFC_CCR_ARAC1 0x00001000 /* 4 Addr, 1 Col 3 Row 512b page */ +#define NDFC_CCR_ARAC2 0x00002000 /* 4 Addr, 2 Col 2 Row 2K page */ +#define NDFC_CCR_ARAC3 0x00003000 /* 5 Addr, 2 Col 3 Row 2K page */ +#define NDFC_CCR_ARAC_MASK 0x00003000 /* Auto-Read mode Addr Cycles */ +#define NDFC_CCR_RPG 0x0000C000 /* Auto-Read Page */ +#define NDFC_CCR_EBCC 0x00000004 /* EBC Configuration Completed */ +#define NDFC_CCR_DHC 0x00000002 /* Direct Hardware Control Enable */ + +#define NDFC_BxCFG_EN 0x80000000 /* Bank Enable */ +#define NDFC_BxCFG_CED 0x40000000 /* nCE Style */ +#define NDFC_BxCFG_SZ_MASK 0x08000000 /* Bank Size */ +#define NDFC_BxCFG_SZ_8BIT 0x00000000 /* 8bit */ +#define NDFC_BxCFG_SZ_16BIT 0x08000000 /* 16bit */ + +#define NDFC_MAX_BANKS 4 + +struct ndfc_controller_settings { + uint32_t ccr_settings; + uint64_t ndfc_erpn; +}; + +struct ndfc_chip_settings { + uint32_t bank_settings; +}; + +#endif diff --git a/roms/u-boot/include/linux/mtd/omap_elm.h b/roms/u-boot/include/linux/mtd/omap_elm.h new file mode 100644 index 000000000..f3db00d55 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/omap_elm.h @@ -0,0 +1,79 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2010-2011 Texas Instruments, <www.ti.com> + * Mansoor Ahamed <mansoor.ahamed@ti.com> + * + * Derived from work done by Rohit Choraria <rohitkc@ti.com> for omap3 + */ +#ifndef __ASM_ARCH_ELM_H +#define __ASM_ARCH_ELM_H +/* + * ELM Module Registers + */ + +/* ELM registers bit fields */ +#define ELM_SYSCONFIG_SOFTRESET_MASK (0x2) +#define ELM_SYSCONFIG_SOFTRESET (0x2) +#define ELM_SYSSTATUS_RESETDONE_MASK (0x1) +#define ELM_SYSSTATUS_RESETDONE (0x1) +#define ELM_LOCATION_CONFIG_ECC_BCH_LEVEL_MASK (0x3) +#define ELM_LOCATION_CONFIG_ECC_SIZE_MASK (0x7FF0000) +#define ELM_LOCATION_CONFIG_ECC_SIZE_POS (16) +#define ELM_SYNDROME_FRAGMENT_6_SYNDROME_VALID (0x00010000) +#define ELM_LOCATION_STATUS_ECC_CORRECTABLE_MASK (0x100) +#define ELM_LOCATION_STATUS_ECC_NB_ERRORS_MASK (0x1F) + +#define ELM_MAX_CHANNELS 8 +#define ELM_MAX_ERROR_COUNT 16 + +#ifndef __ASSEMBLY__ + +enum bch_level { + BCH_4_BIT = 0, + BCH_8_BIT, + BCH_16_BIT +}; + + +/* BCH syndrome registers */ +struct syndrome { + u32 syndrome_fragment_x[7]; /* 0x400, 0x404.... 0x418 */ + u8 res1[36]; /* 0x41c */ +}; + +/* BCH error status & location register */ +struct location { + u32 location_status; /* 0x800 */ + u8 res1[124]; /* 0x804 */ + u32 error_location_x[ELM_MAX_ERROR_COUNT]; /* 0x880, 0x980, .. */ + u8 res2[64]; /* 0x8c0 */ +}; + +/* BCH ELM register map - do not try to allocate memmory for this structure. + * We have used plenty of reserved variables to fill the slots in the ELM + * register memory map. + * Directly initialize the struct pointer to ELM base address. + */ +struct elm { + u32 rev; /* 0x000 */ + u8 res1[12]; /* 0x004 */ + u32 sysconfig; /* 0x010 */ + u32 sysstatus; /* 0x014 */ + u32 irqstatus; /* 0x018 */ + u32 irqenable; /* 0x01c */ + u32 location_config; /* 0x020 */ + u8 res2[92]; /* 0x024 */ + u32 page_ctrl; /* 0x080 */ + u8 res3[892]; /* 0x084 */ + struct syndrome syndrome_fragments[ELM_MAX_CHANNELS]; /* 0x400,0x420 */ + u8 res4[512]; /* 0x600 */ + struct location error_location[ELM_MAX_CHANNELS]; /* 0x800,0x900 ... */ +}; + +int elm_check_error(u8 *syndrome, enum bch_level bch_type, u32 *error_count, + u32 *error_locations); +int elm_config(enum bch_level level); +void elm_reset(void); +void elm_init(void); +#endif /* __ASSEMBLY__ */ +#endif /* __ASM_ARCH_ELM_H */ diff --git a/roms/u-boot/include/linux/mtd/omap_gpmc.h b/roms/u-boot/include/linux/mtd/omap_gpmc.h new file mode 100644 index 000000000..864b05e43 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/omap_gpmc.h @@ -0,0 +1,97 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2004-2008 Texas Instruments, <www.ti.com> + * Rohit Choraria <rohitkc@ti.com> + * + * (C) Copyright 2013 Andreas Bießmann <andreas@biessmann.org> + */ +#ifndef __ASM_OMAP_GPMC_H +#define __ASM_OMAP_GPMC_H + +#define GPMC_BUF_EMPTY 0 +#define GPMC_BUF_FULL 1 +#define GPMC_MAX_SECTORS 8 + +enum omap_ecc { + /* 1-bit ECC calculation by Software, Error detection by Software */ + OMAP_ECC_HAM1_CODE_SW = 1, /* avoid un-initialized int can be 0x0 */ + /* 1-bit ECC calculation by GPMC, Error detection by Software */ + /* ECC layout compatible to legacy ROMCODE. */ + OMAP_ECC_HAM1_CODE_HW, + /* 4-bit ECC calculation by GPMC, Error detection by Software */ + OMAP_ECC_BCH4_CODE_HW_DETECTION_SW, + /* 4-bit ECC calculation by GPMC, Error detection by ELM */ + OMAP_ECC_BCH4_CODE_HW, + /* 8-bit ECC calculation by GPMC, Error detection by Software */ + OMAP_ECC_BCH8_CODE_HW_DETECTION_SW, + /* 8-bit ECC calculation by GPMC, Error detection by ELM */ + OMAP_ECC_BCH8_CODE_HW, + /* 16-bit ECC calculation by GPMC, Error detection by ELM */ + OMAP_ECC_BCH16_CODE_HW, +}; + +struct gpmc_cs { + u32 config1; /* 0x00 */ + u32 config2; /* 0x04 */ + u32 config3; /* 0x08 */ + u32 config4; /* 0x0C */ + u32 config5; /* 0x10 */ + u32 config6; /* 0x14 */ + u32 config7; /* 0x18 */ + u32 nand_cmd; /* 0x1C */ + u32 nand_adr; /* 0x20 */ + u32 nand_dat; /* 0x24 */ + u8 res[8]; /* blow up to 0x30 byte */ +}; + +struct bch_res_0_3 { + u32 bch_result_x[4]; +}; + +struct bch_res_4_6 { + u32 bch_result_x[3]; +}; + +struct gpmc { + u8 res1[0x10]; + u32 sysconfig; /* 0x10 */ + u8 res2[0x4]; + u32 irqstatus; /* 0x18 */ + u32 irqenable; /* 0x1C */ + u8 res3[0x20]; + u32 timeout_control; /* 0x40 */ + u8 res4[0xC]; + u32 config; /* 0x50 */ + u32 status; /* 0x54 */ + u8 res5[0x8]; /* 0x58 */ + struct gpmc_cs cs[8]; /* 0x60, 0x90, .. */ + u32 prefetch_config1; /* 0x1E0 */ + u32 prefetch_config2; /* 0x1E4 */ + u32 res6; /* 0x1E8 */ + u32 prefetch_control; /* 0x1EC */ + u32 prefetch_status; /* 0x1F0 */ + u32 ecc_config; /* 0x1F4 */ + u32 ecc_control; /* 0x1F8 */ + u32 ecc_size_config; /* 0x1FC */ + u32 ecc1_result; /* 0x200 */ + u32 ecc2_result; /* 0x204 */ + u32 ecc3_result; /* 0x208 */ + u32 ecc4_result; /* 0x20C */ + u32 ecc5_result; /* 0x210 */ + u32 ecc6_result; /* 0x214 */ + u32 ecc7_result; /* 0x218 */ + u32 ecc8_result; /* 0x21C */ + u32 ecc9_result; /* 0x220 */ + u8 res7[12]; /* 0x224 */ + u32 testmomde_ctrl; /* 0x230 */ + u8 res8[12]; /* 0x234 */ + struct bch_res_0_3 bch_result_0_3[GPMC_MAX_SECTORS]; /* 0x240,0x250, */ + u8 res9[16 * 4]; /* 0x2C0 - 0x2FF */ + struct bch_res_4_6 bch_result_4_6[GPMC_MAX_SECTORS]; /* 0x300,0x310, */ +}; + +/* Used for board specific gpmc initialization */ +extern const struct gpmc *gpmc_cfg; +extern char gpmc_cs0_flash; + +#endif /* __ASM_OMAP_GPMC_H */ diff --git a/roms/u-boot/include/linux/mtd/onenand.h b/roms/u-boot/include/linux/mtd/onenand.h new file mode 100644 index 000000000..e7b63ddd1 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/onenand.h @@ -0,0 +1,180 @@ +/* + * linux/include/linux/mtd/onenand.h + * + * Copyright (C) 2005-2007 Samsung Electronics + * Kyungmin Park <kyungmin.park@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __LINUX_MTD_ONENAND_H +#define __LINUX_MTD_ONENAND_H + +#include <linux/mtd/onenand_regs.h> + +/* Note: The header order is impoertant */ +#include <onenand_uboot.h> + +#include <linux/compat.h> +#include <linux/mtd/bbm.h> + +#define MAX_DIES 2 +#define MAX_BUFFERRAM 2 +#define MAX_ONENAND_PAGESIZE (4096 + 128) + +/* Scan and identify a OneNAND device */ +extern int onenand_scan (struct mtd_info *mtd, int max_chips); +/* Free resources held by the OneNAND device */ +extern void onenand_release (struct mtd_info *mtd); + +/** + * struct onenand_bufferram - OneNAND BufferRAM Data + * @param blockpage block & page address in BufferRAM + */ +struct onenand_bufferram { + int blockpage; +}; + +/** + * struct onenand_chip - OneNAND Private Flash Chip Data + * @param base [BOARDSPECIFIC] address to access OneNAND + * @dies: [INTERN][FLEXONENAND] number of dies on chip + * @boundary: [INTERN][FLEXONENAND] Boundary of the dies + * @diesize: [INTERN][FLEXONENAND] Size of the dies + * @param chipsize [INTERN] the size of one chip for multichip arrays + * @param device_id [INTERN] device ID + * @param verstion_id [INTERN] version ID + * @technology [INTERN] describes the internal NAND array technology such as SLC or MLC. + * @density_mask: [INTERN] chip density, used for DDP devices + * @param options [BOARDSPECIFIC] various chip options. They can partly be set to inform onenand_scan about + * @param erase_shift [INTERN] number of address bits in a block + * @param page_shift [INTERN] number of address bits in a page + * @param ppb_shift [INTERN] number of address bits in a pages per block + * @param page_mask [INTERN] a page per block mask + * @param writesize [INTERN] a real page size + * @param bufferam_index [INTERN] BufferRAM index + * @param bufferam [INTERN] BufferRAM info + * @param readw [REPLACEABLE] hardware specific function for read short + * @param writew [REPLACEABLE] hardware specific function for write short + * @param command [REPLACEABLE] hardware specific function for writing commands to the chip + * @param wait [REPLACEABLE] hardware specific function for wait on ready + * @param read_bufferram [REPLACEABLE] hardware specific function for BufferRAM Area + * @param write_bufferram [REPLACEABLE] hardware specific function for BufferRAM Area + * @param chip_lock [INTERN] spinlock used to protect access to this structure and the chip + * @param wq [INTERN] wait queue to sleep on if a OneNAND operation is in progress + * @param state [INTERN] the current state of the OneNAND device + * @param autooob [REPLACEABLE] the default (auto)placement scheme + * @param priv [OPTIONAL] pointer to private chip date + */ +struct onenand_chip { + void __iomem *base; + unsigned int dies; + unsigned int boundary[MAX_DIES]; + unsigned int diesize[MAX_DIES]; + unsigned int chipsize; + unsigned int device_id; + unsigned int version_id; + unsigned int technology; + unsigned int density_mask; + unsigned int options; + + unsigned int erase_shift; + unsigned int page_shift; + unsigned int ppb_shift; /* Pages per block shift */ + unsigned int page_mask; + unsigned int writesize; + + unsigned int bufferram_index; + struct onenand_bufferram bufferram[MAX_BUFFERRAM]; + + int (*command) (struct mtd_info *mtd, int cmd, loff_t address, + size_t len); + int (*wait) (struct mtd_info *mtd, int state); + int (*bbt_wait) (struct mtd_info *mtd, int state); + void (*unlock_all)(struct mtd_info *mtd); + int (*read_bufferram) (struct mtd_info *mtd, loff_t addr, int area, + unsigned char *buffer, int offset, size_t count); + int (*write_bufferram) (struct mtd_info *mtd, loff_t addr, int area, + const unsigned char *buffer, int offset, + size_t count); + unsigned short (*read_word) (void __iomem *addr); + void (*write_word) (unsigned short value, void __iomem *addr); + int (*chip_probe)(struct mtd_info *mtd); + void (*mmcontrol) (struct mtd_info *mtd, int sync_read); + int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); + int (*scan_bbt)(struct mtd_info *mtd); + + unsigned char *main_buf; + unsigned char *spare_buf; +#ifdef DONT_USE_UBOOT + spinlock_t chip_lock; + wait_queue_head_t wq; +#endif + int state; + unsigned char *page_buf; + unsigned char *oob_buf; + + struct nand_oobinfo *autooob; + int subpagesize; + struct nand_ecclayout *ecclayout; + + void *bbm; + + void *priv; +}; + +/* + * Helper macros + */ +#define ONENAND_CURRENT_BUFFERRAM(this) (this->bufferram_index) +#define ONENAND_NEXT_BUFFERRAM(this) (this->bufferram_index ^ 1) +#define ONENAND_SET_NEXT_BUFFERRAM(this) (this->bufferram_index ^= 1) +#define ONENAND_SET_PREV_BUFFERRAM(this) (this->bufferram_index ^= 1) +#define ONENAND_SET_BUFFERRAM0(this) (this->bufferram_index = 0) +#define ONENAND_SET_BUFFERRAM1(this) (this->bufferram_index = 1) + +#define FLEXONENAND(this) (this->device_id & DEVICE_IS_FLEXONENAND) +#define ONENAND_IS_MLC(this) (this->technology & ONENAND_TECHNOLOGY_IS_MLC) +#define ONENAND_IS_DDP(this) \ + (this->device_id & ONENAND_DEVICE_IS_DDP) + +#define ONENAND_IS_4KB_PAGE(this) \ + (this->options & ONENAND_HAS_4KB_PAGE) + +#define ONENAND_IS_2PLANE(this) (0) + +/* + * Options bits + */ +#define ONENAND_HAS_CONT_LOCK (0x0001) +#define ONENAND_HAS_UNLOCK_ALL (0x0002) +#define ONENAND_HAS_2PLANE (0x0004) +#define ONENAND_HAS_4KB_PAGE (0x0008) +#define ONENAND_RUNTIME_BADBLOCK_CHECK (0x0200) +#define ONENAND_PAGEBUF_ALLOC (0x1000) +#define ONENAND_OOBBUF_ALLOC (0x2000) + +/* + * OneNAND Flash Manufacturer ID Codes + */ +#define ONENAND_MFR_NUMONYX 0x20 +#define ONENAND_MFR_SAMSUNG 0xec + +/** + * struct nand_manufacturers - NAND Flash Manufacturer ID Structure + * @param name: Manufacturer name + * @param id: manufacturer ID code of device. +*/ +struct onenand_manufacturers { + int id; + char *name; +}; + +int onenand_bbt_read_oob(struct mtd_info *mtd, loff_t from, + struct mtd_oob_ops *ops); + +unsigned int onenand_block(struct onenand_chip *this, loff_t addr); +int flexonenand_region(struct mtd_info *mtd, loff_t addr); +#endif /* __LINUX_MTD_ONENAND_H */ diff --git a/roms/u-boot/include/linux/mtd/onenand_regs.h b/roms/u-boot/include/linux/mtd/onenand_regs.h new file mode 100644 index 000000000..8449a3cdc --- /dev/null +++ b/roms/u-boot/include/linux/mtd/onenand_regs.h @@ -0,0 +1,208 @@ +/* + * linux/include/linux/mtd/onenand_regs.h + * + * OneNAND Register header file + * + * Copyright (C) 2005-2007 Samsung Electronics + * Kyungmin Park <kyungmin.park@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef __ONENAND_REG_H +#define __ONENAND_REG_H + +/* Memory Address Map Translation (Word order) */ +#define ONENAND_MEMORY_MAP(x) ((x) << 1) + +/* + * External BufferRAM area + */ +#define ONENAND_BOOTRAM ONENAND_MEMORY_MAP(0x0000) +#define ONENAND_DATARAM ONENAND_MEMORY_MAP(0x0200) +#define ONENAND_SPARERAM ONENAND_MEMORY_MAP(0x8010) + +/* + * OneNAND Registers + */ +#define ONENAND_REG_MANUFACTURER_ID ONENAND_MEMORY_MAP(0xF000) +#define ONENAND_REG_DEVICE_ID ONENAND_MEMORY_MAP(0xF001) +#define ONENAND_REG_VERSION_ID ONENAND_MEMORY_MAP(0xF002) +#define ONENAND_REG_DATA_BUFFER_SIZE ONENAND_MEMORY_MAP(0xF003) +#define ONENAND_REG_BOOT_BUFFER_SIZE ONENAND_MEMORY_MAP(0xF004) +#define ONENAND_REG_NUM_BUFFERS ONENAND_MEMORY_MAP(0xF005) +#define ONENAND_REG_TECHNOLOGY ONENAND_MEMORY_MAP(0xF006) + +#define ONENAND_REG_START_ADDRESS1 ONENAND_MEMORY_MAP(0xF100) +#define ONENAND_REG_START_ADDRESS2 ONENAND_MEMORY_MAP(0xF101) +#define ONENAND_REG_START_ADDRESS3 ONENAND_MEMORY_MAP(0xF102) +#define ONENAND_REG_START_ADDRESS4 ONENAND_MEMORY_MAP(0xF103) +#define ONENAND_REG_START_ADDRESS5 ONENAND_MEMORY_MAP(0xF104) +#define ONENAND_REG_START_ADDRESS6 ONENAND_MEMORY_MAP(0xF105) +#define ONENAND_REG_START_ADDRESS7 ONENAND_MEMORY_MAP(0xF106) +#define ONENAND_REG_START_ADDRESS8 ONENAND_MEMORY_MAP(0xF107) + +#define ONENAND_REG_START_BUFFER ONENAND_MEMORY_MAP(0xF200) +#define ONENAND_REG_COMMAND ONENAND_MEMORY_MAP(0xF220) +#define ONENAND_REG_SYS_CFG1 ONENAND_MEMORY_MAP(0xF221) +#define ONENAND_REG_SYS_CFG2 ONENAND_MEMORY_MAP(0xF222) +#define ONENAND_REG_CTRL_STATUS ONENAND_MEMORY_MAP(0xF240) +#define ONENAND_REG_INTERRUPT ONENAND_MEMORY_MAP(0xF241) +#define ONENAND_REG_START_BLOCK_ADDRESS ONENAND_MEMORY_MAP(0xF24C) +#define ONENAND_REG_END_BLOCK_ADDRESS ONENAND_MEMORY_MAP(0xF24D) +#define ONENAND_REG_WP_STATUS ONENAND_MEMORY_MAP(0xF24E) + +#define ONENAND_REG_ECC_STATUS ONENAND_MEMORY_MAP(0xFF00) +#define ONENAND_REG_ECC_M0 ONENAND_MEMORY_MAP(0xFF01) +#define ONENAND_REG_ECC_S0 ONENAND_MEMORY_MAP(0xFF02) +#define ONENAND_REG_ECC_M1 ONENAND_MEMORY_MAP(0xFF03) +#define ONENAND_REG_ECC_S1 ONENAND_MEMORY_MAP(0xFF04) +#define ONENAND_REG_ECC_M2 ONENAND_MEMORY_MAP(0xFF05) +#define ONENAND_REG_ECC_S2 ONENAND_MEMORY_MAP(0xFF06) +#define ONENAND_REG_ECC_M3 ONENAND_MEMORY_MAP(0xFF07) +#define ONENAND_REG_ECC_S3 ONENAND_MEMORY_MAP(0xFF08) + +/* + * Device ID Register F001h (R) + */ +#define DEVICE_IS_FLEXONENAND (1 << 9) +#define FLEXONENAND_PI_MASK (0x3ff) +#define FLEXONENAND_PI_UNLOCK_SHIFT (14) +#define ONENAND_DEVICE_DENSITY_MASK (0xf) +#define ONENAND_DEVICE_DENSITY_SHIFT (4) +#define ONENAND_DEVICE_IS_DDP (1 << 3) +#define ONENAND_DEVICE_IS_DEMUX (1 << 2) +#define ONENAND_DEVICE_VCC_MASK (0x3) + +#define ONENAND_DEVICE_DENSITY_512Mb (0x002) +#define ONENAND_DEVICE_DENSITY_1Gb (0x003) +#define ONENAND_DEVICE_DENSITY_2Gb (0x004) +#define ONENAND_DEVICE_DENSITY_4Gb (0x005) + +/* + * Version ID Register F002h (R) + */ +#define ONENAND_VERSION_PROCESS_SHIFT (8) + +/* + * Technology Register F006h (R) + */ +#define ONENAND_TECHNOLOGY_IS_MLC (1 << 0) + +/* + * Start Address 1 F100h (R/W) + */ +#define ONENAND_DDP_SHIFT (15) +#define ONENAND_DDP_CHIP0 (0) +#define ONENAND_DDP_CHIP1 (1 << ONENAND_DDP_SHIFT) + +/* + * Start Address 8 F107h (R/W) + */ +#define ONENAND_FPA_MASK (0x7f) +#define ONENAND_FPA_SHIFT (2) +#define ONENAND_FSA_MASK (0x03) + +/* + * Start Buffer Register F200h (R/W) + */ +#define ONENAND_BSA_MASK (0x03) +#define ONENAND_BSA_SHIFT (8) +#define ONENAND_BSA_BOOTRAM (0 << 2) +#define ONENAND_BSA_DATARAM0 (2 << 2) +#define ONENAND_BSA_DATARAM1 (3 << 2) +#define ONENAND_BSC_MASK (0x07) + +/* + * Command Register F220h (R/W) + */ +#define ONENAND_CMD_READ (0x00) +#define ONENAND_CMD_READOOB (0x13) +#define ONENAND_CMD_PROG (0x80) +#define ONENAND_CMD_PROGOOB (0x1A) +#define ONENAND_CMD_2X_PROG (0x7D) +#define ONENAND_CMD_2X_CACHE_PROG (0x7F) +#define ONENAND_CMD_UNLOCK (0x23) +#define ONENAND_CMD_LOCK (0x2A) +#define ONENAND_CMD_LOCK_TIGHT (0x2C) +#define ONENAND_CMD_UNLOCK_ALL (0x27) +#define ONENAND_CMD_ERASE (0x94) +#define ONENAND_CMD_MULTIBLOCK_ERASE (0x95) +#define ONENAND_CMD_ERASE_VERIFY (0x71) +#define ONENAND_CMD_RESET (0xF0) +#define ONENAND_CMD_READID (0x90) +#define FLEXONENAND_CMD_RESET (0xF3) +#define FLEXONENAND_CMD_PI_UPDATE (0x05) +#define FLEXONENAND_CMD_PI_ACCESS (0x66) +#define FLEXONENAND_CMD_RECOVER_LSB (0x05) + +/* NOTE: Those are not *REAL* commands */ +#define ONENAND_CMD_BUFFERRAM (0x1978) +#define FLEXONENAND_CMD_READ_PI (0x1985) + +/* + * System Configuration 1 Register F221h (R, R/W) + */ +#define ONENAND_SYS_CFG1_SYNC_READ (1 << 15) +#define ONENAND_SYS_CFG1_BRL_7 (7 << 12) +#define ONENAND_SYS_CFG1_BRL_6 (6 << 12) +#define ONENAND_SYS_CFG1_BRL_5 (5 << 12) +#define ONENAND_SYS_CFG1_BRL_4 (4 << 12) +#define ONENAND_SYS_CFG1_BRL_3 (3 << 12) +#define ONENAND_SYS_CFG1_BRL_10 (2 << 12) +#define ONENAND_SYS_CFG1_BRL_9 (1 << 12) +#define ONENAND_SYS_CFG1_BRL_8 (0 << 12) +#define ONENAND_SYS_CFG1_BRL_SHIFT (12) +#define ONENAND_SYS_CFG1_BL_32 (4 << 9) +#define ONENAND_SYS_CFG1_BL_16 (3 << 9) +#define ONENAND_SYS_CFG1_BL_8 (2 << 9) +#define ONENAND_SYS_CFG1_BL_4 (1 << 9) +#define ONENAND_SYS_CFG1_BL_CONT (0 << 9) +#define ONENAND_SYS_CFG1_BL_SHIFT (9) +#define ONENAND_SYS_CFG1_NO_ECC (1 << 8) +#define ONENAND_SYS_CFG1_RDY (1 << 7) +#define ONENAND_SYS_CFG1_INT (1 << 6) +#define ONENAND_SYS_CFG1_IOBE (1 << 5) +#define ONENAND_SYS_CFG1_RDY_CONF (1 << 4) + +/* + * Controller Status Register F240h (R) + */ +#define ONENAND_CTRL_ONGO (1 << 15) +#define ONENAND_CTRL_LOCK (1 << 14) +#define ONENAND_CTRL_LOAD (1 << 13) +#define ONENAND_CTRL_PROGRAM (1 << 12) +#define ONENAND_CTRL_ERASE (1 << 11) +#define ONENAND_CTRL_ERROR (1 << 10) +#define ONENAND_CTRL_RSTB (1 << 7) + +/* + * Interrupt Status Register F241h (R) + */ +#define ONENAND_INT_MASTER (1 << 15) +#define ONENAND_INT_READ (1 << 7) +#define ONENAND_INT_WRITE (1 << 6) +#define ONENAND_INT_ERASE (1 << 5) +#define ONENAND_INT_RESET (1 << 4) +#define ONENAND_INT_CLEAR (0 << 0) + +/* + * NAND Flash Write Protection Status Register F24Eh (R) + */ +#define ONENAND_WP_US (1 << 2) +#define ONENAND_WP_LS (1 << 1) +#define ONENAND_WP_LTS (1 << 0) + +/* + * ECC Status Reigser FF00h (R) + */ +#define ONENAND_ECC_1BIT (1 << 0) +#define ONENAND_ECC_1BIT_ALL (0x5555) +#define ONENAND_ECC_2BIT (1 << 1) +#define ONENAND_ECC_2BIT_ALL (0xAAAA) +#define ONENAND_ECC_4BIT_UNCORRECTABLE (0x1010) +#define FLEXONENAND_UNCORRECTABLE_ERROR (0x1010) + +#endif /* __ONENAND_REG_H */ diff --git a/roms/u-boot/include/linux/mtd/partitions.h b/roms/u-boot/include/linux/mtd/partitions.h new file mode 100644 index 000000000..3822237f2 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/partitions.h @@ -0,0 +1,110 @@ +/* + * MTD partitioning layer definitions + * + * (C) 2000 Nicolas Pitre <nico@fluxnic.net> + * + * This code is GPL + */ + +#ifndef MTD_PARTITIONS_H +#define MTD_PARTITIONS_H + +#include <linux/types.h> + + +/* + * Partition definition structure: + * + * An array of struct partition is passed along with a MTD object to + * mtd_device_register() to create them. + * + * For each partition, these fields are available: + * name: string that will be used to label the partition's MTD device. + * size: the partition size; if defined as MTDPART_SIZ_FULL, the partition + * will extend to the end of the master MTD device. + * offset: absolute starting position within the master MTD device; if + * defined as MTDPART_OFS_APPEND, the partition will start where the + * previous one ended; if MTDPART_OFS_NXTBLK, at the next erase block; + * if MTDPART_OFS_RETAIN, consume as much as possible, leaving size + * after the end of partition. + * mask_flags: contains flags that have to be masked (removed) from the + * master MTD flag set for the corresponding MTD partition. + * For example, to force a read-only partition, simply adding + * MTD_WRITEABLE to the mask_flags will do the trick. + * + * Note: writeable partitions require their size and offset be + * erasesize aligned (e.g. use MTDPART_OFS_NEXTBLK). + */ + +struct mtd_partition { + const char *name; /* identifier string */ + uint64_t size; /* partition size */ + uint64_t offset; /* offset within the master MTD space */ + uint32_t mask_flags; /* master MTD flags to mask out for this partition */ + struct nand_ecclayout *ecclayout; /* out of band layout for this partition (NAND only) */ +}; + +#define MTDPART_OFS_RETAIN (-3) +#define MTDPART_OFS_NXTBLK (-2) +#define MTDPART_OFS_APPEND (-1) +#define MTDPART_SIZ_FULL (0) + + +struct mtd_info; +struct device_node; + +#ifndef __UBOOT__ +/** + * struct mtd_part_parser_data - used to pass data to MTD partition parsers. + * @origin: for RedBoot, start address of MTD device + * @of_node: for OF parsers, device node containing partitioning information + */ +struct mtd_part_parser_data { + unsigned long origin; + struct device_node *of_node; +}; + + +/* + * Functions dealing with the various ways of partitioning the space + */ + +struct mtd_part_parser { + struct list_head list; + struct module *owner; + const char *name; + int (*parse_fn)(struct mtd_info *, struct mtd_partition **, + struct mtd_part_parser_data *); +}; + +extern void register_mtd_parser(struct mtd_part_parser *parser); +extern void deregister_mtd_parser(struct mtd_part_parser *parser); +#endif + +int mtd_add_partition(struct mtd_info *master, const char *name, + long long offset, long long length); +int mtd_del_partition(struct mtd_info *master, int partno); +uint64_t mtd_get_device_size(const struct mtd_info *mtd); + +#if defined(CONFIG_MTD_PARTITIONS) +int mtd_parse_partitions(struct mtd_info *parent, const char **_mtdparts, + struct mtd_partition **_parts, int *_nparts); +void mtd_free_parsed_partitions(struct mtd_partition *parts, + unsigned int nparts); +#else +static inline int +mtd_parse_partitions(struct mtd_info *parent, const char **_mtdparts, + struct mtd_partition **_parts, int *_nparts) +{ + *_nparts = 0; + + return 0; +} +static inline void +mtd_free_parsed_partitions(struct mtd_partition *parts, unsigned int nparts) +{ + return; +} +#endif /* defined(MTD_PARTITIONS) */ + +#endif diff --git a/roms/u-boot/include/linux/mtd/rawnand.h b/roms/u-boot/include/linux/mtd/rawnand.h new file mode 100644 index 000000000..66febc6b7 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/rawnand.h @@ -0,0 +1,1333 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright © 2000-2010 David Woodhouse <dwmw2@infradead.org> + * Steven J. Hill <sjhill@realitydiluted.com> + * Thomas Gleixner <tglx@linutronix.de> + * + * Info: + * Contains standard defines and IDs for NAND flash devices + * + * Changelog: + * See git changelog. + */ +#ifndef __LINUX_MTD_RAWNAND_H +#define __LINUX_MTD_RAWNAND_H + +#include <config.h> + +#include <dm/device.h> +#include <linux/bitops.h> +#include <linux/compat.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/flashchip.h> +#include <linux/mtd/bbm.h> +#include <asm/cache.h> + +struct mtd_info; +struct nand_chip; +struct nand_flash_dev; +struct device_node; + +/* Get the flash and manufacturer id and lookup if the type is supported. */ +struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, + struct nand_chip *chip, + int *maf_id, int *dev_id, + struct nand_flash_dev *type); + +/* Scan and identify a NAND device */ +int nand_scan(struct mtd_info *mtd, int max_chips); +/* + * Separate phases of nand_scan(), allowing board driver to intervene + * and override command or ECC setup according to flash type. + */ +int nand_scan_ident(struct mtd_info *mtd, int max_chips, + struct nand_flash_dev *table); +int nand_scan_tail(struct mtd_info *mtd); + +/* Free resources held by the NAND device */ +void nand_release(struct mtd_info *mtd); + +/* Internal helper for board drivers which need to override command function */ +void nand_wait_ready(struct mtd_info *mtd); + +/* + * This constant declares the max. oobsize / page, which + * is supported now. If you add a chip with bigger oobsize/page + * adjust this accordingly. + */ +#define NAND_MAX_OOBSIZE 1664 +#define NAND_MAX_PAGESIZE 16384 + +/* + * Constants for hardware specific CLE/ALE/NCE function + * + * These are bits which can be or'ed to set/clear multiple + * bits in one go. + */ +/* Select the chip by setting nCE to low */ +#define NAND_NCE 0x01 +/* Select the command latch by setting CLE to high */ +#define NAND_CLE 0x02 +/* Select the address latch by setting ALE to high */ +#define NAND_ALE 0x04 + +#define NAND_CTRL_CLE (NAND_NCE | NAND_CLE) +#define NAND_CTRL_ALE (NAND_NCE | NAND_ALE) +#define NAND_CTRL_CHANGE 0x80 + +/* + * Standard NAND flash commands + */ +#define NAND_CMD_READ0 0 +#define NAND_CMD_READ1 1 +#define NAND_CMD_RNDOUT 5 +#define NAND_CMD_PAGEPROG 0x10 +#define NAND_CMD_READOOB 0x50 +#define NAND_CMD_ERASE1 0x60 +#define NAND_CMD_STATUS 0x70 +#define NAND_CMD_SEQIN 0x80 +#define NAND_CMD_RNDIN 0x85 +#define NAND_CMD_READID 0x90 +#define NAND_CMD_ERASE2 0xd0 +#define NAND_CMD_PARAM 0xec +#define NAND_CMD_GET_FEATURES 0xee +#define NAND_CMD_SET_FEATURES 0xef +#define NAND_CMD_RESET 0xff + +#define NAND_CMD_LOCK 0x2a +#define NAND_CMD_UNLOCK1 0x23 +#define NAND_CMD_UNLOCK2 0x24 + +/* Extended commands for large page devices */ +#define NAND_CMD_READSTART 0x30 +#define NAND_CMD_RNDOUTSTART 0xE0 +#define NAND_CMD_CACHEDPROG 0x15 + +/* Extended commands for AG-AND device */ +/* + * Note: the command for NAND_CMD_DEPLETE1 is really 0x00 but + * there is no way to distinguish that from NAND_CMD_READ0 + * until the remaining sequence of commands has been completed + * so add a high order bit and mask it off in the command. + */ +#define NAND_CMD_DEPLETE1 0x100 +#define NAND_CMD_DEPLETE2 0x38 +#define NAND_CMD_STATUS_MULTI 0x71 +#define NAND_CMD_STATUS_ERROR 0x72 +/* multi-bank error status (banks 0-3) */ +#define NAND_CMD_STATUS_ERROR0 0x73 +#define NAND_CMD_STATUS_ERROR1 0x74 +#define NAND_CMD_STATUS_ERROR2 0x75 +#define NAND_CMD_STATUS_ERROR3 0x76 +#define NAND_CMD_STATUS_RESET 0x7f +#define NAND_CMD_STATUS_CLEAR 0xff + +#define NAND_CMD_NONE -1 + +/* Status bits */ +#define NAND_STATUS_FAIL 0x01 +#define NAND_STATUS_FAIL_N1 0x02 +#define NAND_STATUS_TRUE_READY 0x20 +#define NAND_STATUS_READY 0x40 +#define NAND_STATUS_WP 0x80 + +#define NAND_DATA_IFACE_CHECK_ONLY -1 + +/* + * Constants for ECC_MODES + */ +typedef enum { + NAND_ECC_NONE, + NAND_ECC_SOFT, + NAND_ECC_HW, + NAND_ECC_HW_SYNDROME, + NAND_ECC_HW_OOB_FIRST, + NAND_ECC_SOFT_BCH, +} nand_ecc_modes_t; + +enum nand_ecc_algo { + NAND_ECC_UNKNOWN, + NAND_ECC_HAMMING, + NAND_ECC_BCH, +}; + +/* + * Constants for Hardware ECC + */ +/* Reset Hardware ECC for read */ +#define NAND_ECC_READ 0 +/* Reset Hardware ECC for write */ +#define NAND_ECC_WRITE 1 +/* Enable Hardware ECC before syndrome is read back from flash */ +#define NAND_ECC_READSYN 2 + +/* + * Enable generic NAND 'page erased' check. This check is only done when + * ecc.correct() returns -EBADMSG. + * Set this flag if your implementation does not fix bitflips in erased + * pages and you want to rely on the default implementation. + */ +#define NAND_ECC_GENERIC_ERASED_CHECK BIT(0) +#define NAND_ECC_MAXIMIZE BIT(1) +/* + * If your controller already sends the required NAND commands when + * reading or writing a page, then the framework is not supposed to + * send READ0 and SEQIN/PAGEPROG respectively. + */ +#define NAND_ECC_CUSTOM_PAGE_ACCESS BIT(2) + +/* Bit mask for flags passed to do_nand_read_ecc */ +#define NAND_GET_DEVICE 0x80 + + +/* + * Option constants for bizarre disfunctionality and real + * features. + */ +/* Buswidth is 16 bit */ +#define NAND_BUSWIDTH_16 0x00000002 +/* Device supports partial programming without padding */ +#define NAND_NO_PADDING 0x00000004 +/* Chip has cache program function */ +#define NAND_CACHEPRG 0x00000008 +/* Chip has copy back function */ +#define NAND_COPYBACK 0x00000010 +/* + * Chip requires ready check on read (for auto-incremented sequential read). + * True only for small page devices; large page devices do not support + * autoincrement. + */ +#define NAND_NEED_READRDY 0x00000100 + +/* Chip does not allow subpage writes */ +#define NAND_NO_SUBPAGE_WRITE 0x00000200 + +/* Device is one of 'new' xD cards that expose fake nand command set */ +#define NAND_BROKEN_XD 0x00000400 + +/* Device behaves just like nand, but is readonly */ +#define NAND_ROM 0x00000800 + +/* Device supports subpage reads */ +#define NAND_SUBPAGE_READ 0x00001000 + +/* + * Some MLC NANDs need data scrambling to limit bitflips caused by repeated + * patterns. + */ +#define NAND_NEED_SCRAMBLING 0x00002000 + +/* Device needs 3rd row address cycle */ +#define NAND_ROW_ADDR_3 0x00004000 + +/* Options valid for Samsung large page devices */ +#define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG + +/* Macros to identify the above */ +#define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) +#define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ)) +#define NAND_HAS_SUBPAGE_WRITE(chip) !((chip)->options & NAND_NO_SUBPAGE_WRITE) + +/* Non chip related options */ +/* This option skips the bbt scan during initialization. */ +#define NAND_SKIP_BBTSCAN 0x00010000 +/* + * This option is defined if the board driver allocates its own buffers + * (e.g. because it needs them DMA-coherent). + */ +#define NAND_OWN_BUFFERS 0x00020000 +/* Chip may not exist, so silence any errors in scan */ +#define NAND_SCAN_SILENT_NODEV 0x00040000 +/* + * Autodetect nand buswidth with readid/onfi. + * This suppose the driver will configure the hardware in 8 bits mode + * when calling nand_scan_ident, and update its configuration + * before calling nand_scan_tail. + */ +#define NAND_BUSWIDTH_AUTO 0x00080000 +/* + * This option could be defined by controller drivers to protect against + * kmap'ed, vmalloc'ed highmem buffers being passed from upper layers + */ +#define NAND_USE_BOUNCE_BUFFER 0x00100000 + +/* Options set by nand scan */ +/* bbt has already been read */ +#define NAND_BBT_SCANNED 0x40000000 +/* Nand scan has allocated controller struct */ +#define NAND_CONTROLLER_ALLOC 0x80000000 + +/* Cell info constants */ +#define NAND_CI_CHIPNR_MSK 0x03 +#define NAND_CI_CELLTYPE_MSK 0x0C +#define NAND_CI_CELLTYPE_SHIFT 2 + +/* ONFI features */ +#define ONFI_FEATURE_16_BIT_BUS (1 << 0) +#define ONFI_FEATURE_EXT_PARAM_PAGE (1 << 7) + +/* ONFI timing mode, used in both asynchronous and synchronous mode */ +#define ONFI_TIMING_MODE_0 (1 << 0) +#define ONFI_TIMING_MODE_1 (1 << 1) +#define ONFI_TIMING_MODE_2 (1 << 2) +#define ONFI_TIMING_MODE_3 (1 << 3) +#define ONFI_TIMING_MODE_4 (1 << 4) +#define ONFI_TIMING_MODE_5 (1 << 5) +#define ONFI_TIMING_MODE_UNKNOWN (1 << 6) + +/* ONFI feature address */ +#define ONFI_FEATURE_ADDR_TIMING_MODE 0x1 + +/* Vendor-specific feature address (Micron) */ +#define ONFI_FEATURE_ADDR_READ_RETRY 0x89 + +/* ONFI subfeature parameters length */ +#define ONFI_SUBFEATURE_PARAM_LEN 4 + +/* ONFI optional commands SET/GET FEATURES supported? */ +#define ONFI_OPT_CMD_SET_GET_FEATURES (1 << 2) + +struct nand_onfi_params { + /* rev info and features block */ + /* 'O' 'N' 'F' 'I' */ + u8 sig[4]; + __le16 revision; + __le16 features; + __le16 opt_cmd; + u8 reserved0[2]; + __le16 ext_param_page_length; /* since ONFI 2.1 */ + u8 num_of_param_pages; /* since ONFI 2.1 */ + u8 reserved1[17]; + + /* manufacturer information block */ + char manufacturer[12]; + char model[20]; + u8 jedec_id; + __le16 date_code; + u8 reserved2[13]; + + /* memory organization block */ + __le32 byte_per_page; + __le16 spare_bytes_per_page; + __le32 data_bytes_per_ppage; + __le16 spare_bytes_per_ppage; + __le32 pages_per_block; + __le32 blocks_per_lun; + u8 lun_count; + u8 addr_cycles; + u8 bits_per_cell; + __le16 bb_per_lun; + __le16 block_endurance; + u8 guaranteed_good_blocks; + __le16 guaranteed_block_endurance; + u8 programs_per_page; + u8 ppage_attr; + u8 ecc_bits; + u8 interleaved_bits; + u8 interleaved_ops; + u8 reserved3[13]; + + /* electrical parameter block */ + u8 io_pin_capacitance_max; + __le16 async_timing_mode; + __le16 program_cache_timing_mode; + __le16 t_prog; + __le16 t_bers; + __le16 t_r; + __le16 t_ccs; + __le16 src_sync_timing_mode; + u8 src_ssync_features; + __le16 clk_pin_capacitance_typ; + __le16 io_pin_capacitance_typ; + __le16 input_pin_capacitance_typ; + u8 input_pin_capacitance_max; + u8 driver_strength_support; + __le16 t_int_r; + __le16 t_adl; + u8 reserved4[8]; + + /* vendor */ + __le16 vendor_revision; + u8 vendor[88]; + + __le16 crc; +} __packed; + +#define ONFI_CRC_BASE 0x4F4E + +/* Extended ECC information Block Definition (since ONFI 2.1) */ +struct onfi_ext_ecc_info { + u8 ecc_bits; + u8 codeword_size; + __le16 bb_per_lun; + __le16 block_endurance; + u8 reserved[2]; +} __packed; + +#define ONFI_SECTION_TYPE_0 0 /* Unused section. */ +#define ONFI_SECTION_TYPE_1 1 /* for additional sections. */ +#define ONFI_SECTION_TYPE_2 2 /* for ECC information. */ +struct onfi_ext_section { + u8 type; + u8 length; +} __packed; + +#define ONFI_EXT_SECTION_MAX 8 + +/* Extended Parameter Page Definition (since ONFI 2.1) */ +struct onfi_ext_param_page { + __le16 crc; + u8 sig[4]; /* 'E' 'P' 'P' 'S' */ + u8 reserved0[10]; + struct onfi_ext_section sections[ONFI_EXT_SECTION_MAX]; + + /* + * The actual size of the Extended Parameter Page is in + * @ext_param_page_length of nand_onfi_params{}. + * The following are the variable length sections. + * So we do not add any fields below. Please see the ONFI spec. + */ +} __packed; + +struct nand_onfi_vendor_micron { + u8 two_plane_read; + u8 read_cache; + u8 read_unique_id; + u8 dq_imped; + u8 dq_imped_num_settings; + u8 dq_imped_feat_addr; + u8 rb_pulldown_strength; + u8 rb_pulldown_strength_feat_addr; + u8 rb_pulldown_strength_num_settings; + u8 otp_mode; + u8 otp_page_start; + u8 otp_data_prot_addr; + u8 otp_num_pages; + u8 otp_feat_addr; + u8 read_retry_options; + u8 reserved[72]; + u8 param_revision; +} __packed; + +struct jedec_ecc_info { + u8 ecc_bits; + u8 codeword_size; + __le16 bb_per_lun; + __le16 block_endurance; + u8 reserved[2]; +} __packed; + +/* JEDEC features */ +#define JEDEC_FEATURE_16_BIT_BUS (1 << 0) + +struct nand_jedec_params { + /* rev info and features block */ + /* 'J' 'E' 'S' 'D' */ + u8 sig[4]; + __le16 revision; + __le16 features; + u8 opt_cmd[3]; + __le16 sec_cmd; + u8 num_of_param_pages; + u8 reserved0[18]; + + /* manufacturer information block */ + char manufacturer[12]; + char model[20]; + u8 jedec_id[6]; + u8 reserved1[10]; + + /* memory organization block */ + __le32 byte_per_page; + __le16 spare_bytes_per_page; + u8 reserved2[6]; + __le32 pages_per_block; + __le32 blocks_per_lun; + u8 lun_count; + u8 addr_cycles; + u8 bits_per_cell; + u8 programs_per_page; + u8 multi_plane_addr; + u8 multi_plane_op_attr; + u8 reserved3[38]; + + /* electrical parameter block */ + __le16 async_sdr_speed_grade; + __le16 toggle_ddr_speed_grade; + __le16 sync_ddr_speed_grade; + u8 async_sdr_features; + u8 toggle_ddr_features; + u8 sync_ddr_features; + __le16 t_prog; + __le16 t_bers; + __le16 t_r; + __le16 t_r_multi_plane; + __le16 t_ccs; + __le16 io_pin_capacitance_typ; + __le16 input_pin_capacitance_typ; + __le16 clk_pin_capacitance_typ; + u8 driver_strength_support; + __le16 t_adl; + u8 reserved4[36]; + + /* ECC and endurance block */ + u8 guaranteed_good_blocks; + __le16 guaranteed_block_endurance; + struct jedec_ecc_info ecc_info[4]; + u8 reserved5[29]; + + /* reserved */ + u8 reserved6[148]; + + /* vendor */ + __le16 vendor_rev_num; + u8 reserved7[88]; + + /* CRC for Parameter Page */ + __le16 crc; +} __packed; + +/** + * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices + * @lock: protection lock + * @active: the mtd device which holds the controller currently + * @wq: wait queue to sleep on if a NAND operation is in + * progress used instead of the per chip wait queue + * when a hw controller is available. + */ +struct nand_hw_control { + spinlock_t lock; + struct nand_chip *active; +}; + +static inline void nand_hw_control_init(struct nand_hw_control *nfc) +{ + nfc->active = NULL; + spin_lock_init(&nfc->lock); + init_waitqueue_head(&nfc->wq); +} + +/** + * struct nand_ecc_step_info - ECC step information of ECC engine + * @stepsize: data bytes per ECC step + * @strengths: array of supported strengths + * @nstrengths: number of supported strengths + */ +struct nand_ecc_step_info { + int stepsize; + const int *strengths; + int nstrengths; +}; + +/** + * struct nand_ecc_caps - capability of ECC engine + * @stepinfos: array of ECC step information + * @nstepinfos: number of ECC step information + * @calc_ecc_bytes: driver's hook to calculate ECC bytes per step + */ +struct nand_ecc_caps { + const struct nand_ecc_step_info *stepinfos; + int nstepinfos; + int (*calc_ecc_bytes)(int step_size, int strength); +}; + +/* a shorthand to generate struct nand_ecc_caps with only one ECC stepsize */ +#define NAND_ECC_CAPS_SINGLE(__name, __calc, __step, ...) \ +static const int __name##_strengths[] = { __VA_ARGS__ }; \ +static const struct nand_ecc_step_info __name##_stepinfo = { \ + .stepsize = __step, \ + .strengths = __name##_strengths, \ + .nstrengths = ARRAY_SIZE(__name##_strengths), \ +}; \ +static const struct nand_ecc_caps __name = { \ + .stepinfos = &__name##_stepinfo, \ + .nstepinfos = 1, \ + .calc_ecc_bytes = __calc, \ +} + +/** + * struct nand_ecc_ctrl - Control structure for ECC + * @mode: ECC mode + * @algo: ECC algorithm + * @steps: number of ECC steps per page + * @size: data bytes per ECC step + * @bytes: ECC bytes per step + * @strength: max number of correctible bits per ECC step + * @total: total number of ECC bytes per page + * @prepad: padding information for syndrome based ECC generators + * @postpad: padding information for syndrome based ECC generators + * @options: ECC specific options (see NAND_ECC_XXX flags defined above) + * @layout: ECC layout control struct pointer + * @priv: pointer to private ECC control data + * @hwctl: function to control hardware ECC generator. Must only + * be provided if an hardware ECC is available + * @calculate: function for ECC calculation or readback from ECC hardware + * @correct: function for ECC correction, matching to ECC generator (sw/hw). + * Should return a positive number representing the number of + * corrected bitflips, -EBADMSG if the number of bitflips exceed + * ECC strength, or any other error code if the error is not + * directly related to correction. + * If -EBADMSG is returned the input buffers should be left + * untouched. + * @read_page_raw: function to read a raw page without ECC. This function + * should hide the specific layout used by the ECC + * controller and always return contiguous in-band and + * out-of-band data even if they're not stored + * contiguously on the NAND chip (e.g. + * NAND_ECC_HW_SYNDROME interleaves in-band and + * out-of-band data). + * @write_page_raw: function to write a raw page without ECC. This function + * should hide the specific layout used by the ECC + * controller and consider the passed data as contiguous + * in-band and out-of-band data. ECC controller is + * responsible for doing the appropriate transformations + * to adapt to its specific layout (e.g. + * NAND_ECC_HW_SYNDROME interleaves in-band and + * out-of-band data). + * @read_page: function to read a page according to the ECC generator + * requirements; returns maximum number of bitflips corrected in + * any single ECC step, 0 if bitflips uncorrectable, -EIO hw error + * @read_subpage: function to read parts of the page covered by ECC; + * returns same as read_page() + * @write_subpage: function to write parts of the page covered by ECC. + * @write_page: function to write a page according to the ECC generator + * requirements. + * @write_oob_raw: function to write chip OOB data without ECC + * @read_oob_raw: function to read chip OOB data without ECC + * @read_oob: function to read chip OOB data + * @write_oob: function to write chip OOB data + */ +struct nand_ecc_ctrl { + nand_ecc_modes_t mode; + enum nand_ecc_algo algo; + int steps; + int size; + int bytes; + int total; + int strength; + int prepad; + int postpad; + unsigned int options; + struct nand_ecclayout *layout; + void *priv; + void (*hwctl)(struct mtd_info *mtd, int mode); + int (*calculate)(struct mtd_info *mtd, const uint8_t *dat, + uint8_t *ecc_code); + int (*correct)(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc, + uint8_t *calc_ecc); + int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page); + int (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required, int page); + int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip, + uint8_t *buf, int oob_required, int page); + int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offs, uint32_t len, uint8_t *buf, int page); + int (*write_subpage)(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offset, uint32_t data_len, + const uint8_t *data_buf, int oob_required, int page); + int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, + const uint8_t *buf, int oob_required, int page); + int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, + int page); + int (*read_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, + int page); + int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page); + int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip, + int page); +}; + +static inline int nand_standard_page_accessors(struct nand_ecc_ctrl *ecc) +{ + return !(ecc->options & NAND_ECC_CUSTOM_PAGE_ACCESS); +} + +/** + * struct nand_buffers - buffer structure for read/write + * @ecccalc: buffer pointer for calculated ECC, size is oobsize. + * @ecccode: buffer pointer for ECC read from flash, size is oobsize. + * @databuf: buffer pointer for data, size is (page size + oobsize). + * + * Do not change the order of buffers. databuf and oobrbuf must be in + * consecutive order. + */ +struct nand_buffers { + uint8_t ecccalc[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)]; + uint8_t ecccode[ALIGN(NAND_MAX_OOBSIZE, ARCH_DMA_MINALIGN)]; + uint8_t databuf[ALIGN(NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE, + ARCH_DMA_MINALIGN)]; +}; + +/** + * struct nand_sdr_timings - SDR NAND chip timings + * + * This struct defines the timing requirements of a SDR NAND chip. + * These information can be found in every NAND datasheets and the timings + * meaning are described in the ONFI specifications: + * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing + * Parameters) + * + * All these timings are expressed in picoseconds. + * + * @tBERS_max: Block erase time + * @tCCS_min: Change column setup time + * @tPROG_max: Page program time + * @tR_max: Page read time + * @tALH_min: ALE hold time + * @tADL_min: ALE to data loading time + * @tALS_min: ALE setup time + * @tAR_min: ALE to RE# delay + * @tCEA_max: CE# access time + * @tCEH_min: CE# high hold time + * @tCH_min: CE# hold time + * @tCHZ_max: CE# high to output hi-Z + * @tCLH_min: CLE hold time + * @tCLR_min: CLE to RE# delay + * @tCLS_min: CLE setup time + * @tCOH_min: CE# high to output hold + * @tCS_min: CE# setup time + * @tDH_min: Data hold time + * @tDS_min: Data setup time + * @tFEAT_max: Busy time for Set Features and Get Features + * @tIR_min: Output hi-Z to RE# low + * @tITC_max: Interface and Timing Mode Change time + * @tRC_min: RE# cycle time + * @tREA_max: RE# access time + * @tREH_min: RE# high hold time + * @tRHOH_min: RE# high to output hold + * @tRHW_min: RE# high to WE# low + * @tRHZ_max: RE# high to output hi-Z + * @tRLOH_min: RE# low to output hold + * @tRP_min: RE# pulse width + * @tRR_min: Ready to RE# low (data only) + * @tRST_max: Device reset time, measured from the falling edge of R/B# to the + * rising edge of R/B#. + * @tWB_max: WE# high to SR[6] low + * @tWC_min: WE# cycle time + * @tWH_min: WE# high hold time + * @tWHR_min: WE# high to RE# low + * @tWP_min: WE# pulse width + * @tWW_min: WP# transition to WE# low + */ +struct nand_sdr_timings { + u64 tBERS_max; + u32 tCCS_min; + u64 tPROG_max; + u64 tR_max; + u32 tALH_min; + u32 tADL_min; + u32 tALS_min; + u32 tAR_min; + u32 tCEA_max; + u32 tCEH_min; + u32 tCH_min; + u32 tCHZ_max; + u32 tCLH_min; + u32 tCLR_min; + u32 tCLS_min; + u32 tCOH_min; + u32 tCS_min; + u32 tDH_min; + u32 tDS_min; + u32 tFEAT_max; + u32 tIR_min; + u32 tITC_max; + u32 tRC_min; + u32 tREA_max; + u32 tREH_min; + u32 tRHOH_min; + u32 tRHW_min; + u32 tRHZ_max; + u32 tRLOH_min; + u32 tRP_min; + u32 tRR_min; + u64 tRST_max; + u32 tWB_max; + u32 tWC_min; + u32 tWH_min; + u32 tWHR_min; + u32 tWP_min; + u32 tWW_min; +}; + +/** + * enum nand_data_interface_type - NAND interface timing type + * @NAND_SDR_IFACE: Single Data Rate interface + */ +enum nand_data_interface_type { + NAND_SDR_IFACE, +}; + +/** + * struct nand_data_interface - NAND interface timing + * @type: type of the timing + * @timings: The timing, type according to @type + */ +struct nand_data_interface { + enum nand_data_interface_type type; + union { + struct nand_sdr_timings sdr; + } timings; +}; + +/** + * nand_get_sdr_timings - get SDR timing from data interface + * @conf: The data interface + */ +static inline const struct nand_sdr_timings * +nand_get_sdr_timings(const struct nand_data_interface *conf) +{ + if (conf->type != NAND_SDR_IFACE) + return ERR_PTR(-EINVAL); + + return &conf->timings.sdr; +} + +/** + * struct nand_chip - NAND Private Flash Chip Data + * @mtd: MTD device registered to the MTD framework + * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the + * flash device + * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the + * flash device. + * @flash_node: [BOARDSPECIFIC] device node describing this instance + * @read_byte: [REPLACEABLE] read one byte from the chip + * @read_word: [REPLACEABLE] read one word from the chip + * @write_byte: [REPLACEABLE] write a single byte to the chip on the + * low 8 I/O lines + * @write_buf: [REPLACEABLE] write data from the buffer to the chip + * @read_buf: [REPLACEABLE] read data from the chip into the buffer + * @select_chip: [REPLACEABLE] select chip nr + * @block_bad: [REPLACEABLE] check if a block is bad, using OOB markers + * @block_markbad: [REPLACEABLE] mark a block bad + * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling + * ALE/CLE/nCE. Also used to write command and address + * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing + * device ready/busy line. If set to NULL no access to + * ready/busy is available and the ready/busy information + * is read from the chip status register. + * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing + * commands to the chip. + * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on + * ready. + * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for + * setting the read-retry mode. Mostly needed for MLC NAND. + * @ecc: [BOARDSPECIFIC] ECC control structure + * @buffers: buffer structure for read/write + * @buf_align: minimum buffer alignment required by a platform + * @hwcontrol: platform-specific hardware control structure + * @erase: [REPLACEABLE] erase function + * @scan_bbt: [REPLACEABLE] function to scan bad block table + * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring + * data from array to read regs (tR). + * @state: [INTERN] the current state of the NAND device + * @oob_poi: "poison value buffer," used for laying out OOB data + * before writing + * @page_shift: [INTERN] number of address bits in a page (column + * address bits). + * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock + * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry + * @chip_shift: [INTERN] number of address bits in one chip + * @options: [BOARDSPECIFIC] various chip options. They can partly + * be set to inform nand_scan about special functionality. + * See the defines for further explanation. + * @bbt_options: [INTERN] bad block specific options. All options used + * here must come from bbm.h. By default, these options + * will be copied to the appropriate nand_bbt_descr's. + * @badblockpos: [INTERN] position of the bad block marker in the oob + * area. + * @badblockbits: [INTERN] minimum number of set bits in a good block's + * bad block marker position; i.e., BBM == 11110111b is + * not bad when badblockbits == 7 + * @bits_per_cell: [INTERN] number of bits per cell. i.e., 1 means SLC. + * @ecc_strength_ds: [INTERN] ECC correctability from the datasheet. + * Minimum amount of bit errors per @ecc_step_ds guaranteed + * to be correctable. If unknown, set to zero. + * @ecc_step_ds: [INTERN] ECC step required by the @ecc_strength_ds, + * also from the datasheet. It is the recommended ECC step + * size, if known; if unknown, set to zero. + * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is + * set to the actually used ONFI mode if the chip is + * ONFI compliant or deduced from the datasheet if + * the NAND chip is not ONFI compliant. + * @numchips: [INTERN] number of physical chips + * @chipsize: [INTERN] the size of one chip for multichip arrays + * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 + * @pagebuf: [INTERN] holds the pagenumber which is currently in + * data_buf. + * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is + * currently in data_buf. + * @subpagesize: [INTERN] holds the subpagesize + * @onfi_version: [INTERN] holds the chip ONFI version (BCD encoded), + * non 0 if ONFI supported. + * @jedec_version: [INTERN] holds the chip JEDEC version (BCD encoded), + * non 0 if JEDEC supported. + * @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is + * supported, 0 otherwise. + * @jedec_params: [INTERN] holds the JEDEC parameter page when JEDEC is + * supported, 0 otherwise. + * @read_retries: [INTERN] the number of read retry modes supported + * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand + * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand + * @setup_data_interface: [OPTIONAL] setup the data interface and timing. If + * chipnr is set to %NAND_DATA_IFACE_CHECK_ONLY this + * means the configuration should not be applied but + * only checked. + * @bbt: [INTERN] bad block table pointer + * @bbt_td: [REPLACEABLE] bad block table descriptor for flash + * lookup. + * @bbt_md: [REPLACEABLE] bad block table mirror descriptor + * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial + * bad block scan. + * @controller: [REPLACEABLE] a pointer to a hardware controller + * structure which is shared among multiple independent + * devices. + * @priv: [OPTIONAL] pointer to private chip data + * @write_page: [REPLACEABLE] High-level page write function + */ + +struct nand_chip { + struct mtd_info mtd; + void __iomem *IO_ADDR_R; + void __iomem *IO_ADDR_W; + + int flash_node; + + uint8_t (*read_byte)(struct mtd_info *mtd); + u16 (*read_word)(struct mtd_info *mtd); + void (*write_byte)(struct mtd_info *mtd, uint8_t byte); + void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); + void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); + void (*select_chip)(struct mtd_info *mtd, int chip); + int (*block_bad)(struct mtd_info *mtd, loff_t ofs); + int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); + void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); + int (*dev_ready)(struct mtd_info *mtd); + void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, + int page_addr); + int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); + int (*erase)(struct mtd_info *mtd, int page); + int (*scan_bbt)(struct mtd_info *mtd); + int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, + uint32_t offset, int data_len, const uint8_t *buf, + int oob_required, int page, int raw); + int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip, + int feature_addr, uint8_t *subfeature_para); + int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip, + int feature_addr, uint8_t *subfeature_para); + int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode); + int (*setup_data_interface)(struct mtd_info *mtd, int chipnr, + const struct nand_data_interface *conf); + + + int chip_delay; + unsigned int options; + unsigned int bbt_options; + + int page_shift; + int phys_erase_shift; + int bbt_erase_shift; + int chip_shift; + int numchips; + uint64_t chipsize; + int pagemask; + int pagebuf; + unsigned int pagebuf_bitflips; + int subpagesize; + uint8_t bits_per_cell; + uint16_t ecc_strength_ds; + uint16_t ecc_step_ds; + int onfi_timing_mode_default; + int badblockpos; + int badblockbits; + + int onfi_version; + int jedec_version; + struct nand_onfi_params onfi_params; + struct nand_jedec_params jedec_params; + + struct nand_data_interface *data_interface; + + int read_retries; + + flstate_t state; + + uint8_t *oob_poi; + struct nand_hw_control *controller; + struct nand_ecclayout *ecclayout; + + struct nand_ecc_ctrl ecc; + struct nand_buffers *buffers; + unsigned long buf_align; + struct nand_hw_control hwcontrol; + + uint8_t *bbt; + struct nand_bbt_descr *bbt_td; + struct nand_bbt_descr *bbt_md; + + struct nand_bbt_descr *badblock_pattern; + + void *priv; +}; + +static inline void nand_set_flash_node(struct nand_chip *chip, + ofnode node) +{ + chip->flash_node = ofnode_to_offset(node); +} + +static inline ofnode nand_get_flash_node(struct nand_chip *chip) +{ + return offset_to_ofnode(chip->flash_node); +} + +static inline struct nand_chip *mtd_to_nand(struct mtd_info *mtd) +{ + return container_of(mtd, struct nand_chip, mtd); +} + +static inline struct mtd_info *nand_to_mtd(struct nand_chip *chip) +{ + return &chip->mtd; +} + +static inline void *nand_get_controller_data(struct nand_chip *chip) +{ + return chip->priv; +} + +static inline void nand_set_controller_data(struct nand_chip *chip, void *priv) +{ + chip->priv = priv; +} + +/* + * NAND Flash Manufacturer ID Codes + */ +#define NAND_MFR_TOSHIBA 0x98 +#define NAND_MFR_SAMSUNG 0xec +#define NAND_MFR_FUJITSU 0x04 +#define NAND_MFR_NATIONAL 0x8f +#define NAND_MFR_RENESAS 0x07 +#define NAND_MFR_STMICRO 0x20 +#define NAND_MFR_HYNIX 0xad +#define NAND_MFR_MICRON 0x2c +#define NAND_MFR_AMD 0x01 +#define NAND_MFR_MACRONIX 0xc2 +#define NAND_MFR_EON 0x92 +#define NAND_MFR_SANDISK 0x45 +#define NAND_MFR_INTEL 0x89 +#define NAND_MFR_ATO 0x9b + +/* The maximum expected count of bytes in the NAND ID sequence */ +#define NAND_MAX_ID_LEN 8 + +/* + * A helper for defining older NAND chips where the second ID byte fully + * defined the chip, including the geometry (chip size, eraseblock size, page + * size). All these chips have 512 bytes NAND page size. + */ +#define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts) \ + { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \ + .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) } + +/* + * A helper for defining newer chips which report their page size and + * eraseblock size via the extended ID bytes. + * + * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with + * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the + * device ID now only represented a particular total chip size (and voltage, + * buswidth), and the page size, eraseblock size, and OOB size could vary while + * using the same device ID. + */ +#define EXTENDED_ID_NAND(nm, devid, chipsz, opts) \ + { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \ + .options = (opts) } + +#define NAND_ECC_INFO(_strength, _step) \ + { .strength_ds = (_strength), .step_ds = (_step) } +#define NAND_ECC_STRENGTH(type) ((type)->ecc.strength_ds) +#define NAND_ECC_STEP(type) ((type)->ecc.step_ds) + +/** + * struct nand_flash_dev - NAND Flash Device ID Structure + * @name: a human-readable name of the NAND chip + * @dev_id: the device ID (the second byte of the full chip ID array) + * @mfr_id: manufecturer ID part of the full chip ID array (refers the same + * memory address as @id[0]) + * @dev_id: device ID part of the full chip ID array (refers the same memory + * address as @id[1]) + * @id: full device ID array + * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as + * well as the eraseblock size) is determined from the extended NAND + * chip ID array) + * @chipsize: total chip size in MiB + * @erasesize: eraseblock size in bytes (determined from the extended ID if 0) + * @options: stores various chip bit options + * @id_len: The valid length of the @id. + * @oobsize: OOB size + * @ecc: ECC correctability and step information from the datasheet. + * @ecc.strength_ds: The ECC correctability from the datasheet, same as the + * @ecc_strength_ds in nand_chip{}. + * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the + * @ecc_step_ds in nand_chip{}, also from the datasheet. + * For example, the "4bit ECC for each 512Byte" can be set with + * NAND_ECC_INFO(4, 512). + * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND + * reset. Should be deduced from timings described + * in the datasheet. + * + */ +struct nand_flash_dev { + char *name; + union { + struct { + uint8_t mfr_id; + uint8_t dev_id; + }; + uint8_t id[NAND_MAX_ID_LEN]; + }; + unsigned int pagesize; + unsigned int chipsize; + unsigned int erasesize; + unsigned int options; + uint16_t id_len; + uint16_t oobsize; + struct { + uint16_t strength_ds; + uint16_t step_ds; + } ecc; + int onfi_timing_mode_default; +}; + +/** + * struct nand_manufacturers - NAND Flash Manufacturer ID Structure + * @name: Manufacturer name + * @id: manufacturer ID code of device. +*/ +struct nand_manufacturers { + int id; + char *name; +}; + +extern struct nand_flash_dev nand_flash_ids[]; +extern struct nand_manufacturers nand_manuf_ids[]; + +int nand_default_bbt(struct mtd_info *mtd); +int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs); +int nand_isreserved_bbt(struct mtd_info *mtd, loff_t offs); +int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); +int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, + int allowbbt); +int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, uint8_t *buf); + +/* +* Constants for oob configuration +*/ +#define NAND_SMALL_BADBLOCK_POS 5 +#define NAND_LARGE_BADBLOCK_POS 0 + +/** + * struct platform_nand_chip - chip level device structure + * @nr_chips: max. number of chips to scan for + * @chip_offset: chip number offset + * @nr_partitions: number of partitions pointed to by partitions (or zero) + * @partitions: mtd partition list + * @chip_delay: R/B delay value in us + * @options: Option flags, e.g. 16bit buswidth + * @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH + * @part_probe_types: NULL-terminated array of probe types + */ +struct platform_nand_chip { + int nr_chips; + int chip_offset; + int nr_partitions; + struct mtd_partition *partitions; + int chip_delay; + unsigned int options; + unsigned int bbt_options; + const char **part_probe_types; +}; + +/* Keep gcc happy */ +struct platform_device; + +/** + * struct platform_nand_ctrl - controller level device structure + * @probe: platform specific function to probe/setup hardware + * @remove: platform specific function to remove/teardown hardware + * @hwcontrol: platform specific hardware control structure + * @dev_ready: platform specific function to read ready/busy pin + * @select_chip: platform specific chip select function + * @cmd_ctrl: platform specific function for controlling + * ALE/CLE/nCE. Also used to write command and address + * @write_buf: platform specific function for write buffer + * @read_buf: platform specific function for read buffer + * @read_byte: platform specific function to read one byte from chip + * @priv: private data to transport driver specific settings + * + * All fields are optional and depend on the hardware driver requirements + */ +struct platform_nand_ctrl { + int (*probe)(struct platform_device *pdev); + void (*remove)(struct platform_device *pdev); + void (*hwcontrol)(struct mtd_info *mtd, int cmd); + int (*dev_ready)(struct mtd_info *mtd); + void (*select_chip)(struct mtd_info *mtd, int chip); + void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); + void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); + void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); + unsigned char (*read_byte)(struct mtd_info *mtd); + void *priv; +}; + +/** + * struct platform_nand_data - container structure for platform-specific data + * @chip: chip level chip structure + * @ctrl: controller level device structure + */ +struct platform_nand_data { + struct platform_nand_chip chip; + struct platform_nand_ctrl ctrl; +}; + +#ifdef CONFIG_SYS_NAND_ONFI_DETECTION +/* return the supported features. */ +static inline int onfi_feature(struct nand_chip *chip) +{ + return chip->onfi_version ? le16_to_cpu(chip->onfi_params.features) : 0; +} + +/* return the supported asynchronous timing mode. */ +static inline int onfi_get_async_timing_mode(struct nand_chip *chip) +{ + if (!chip->onfi_version) + return ONFI_TIMING_MODE_UNKNOWN; + return le16_to_cpu(chip->onfi_params.async_timing_mode); +} + +/* return the supported synchronous timing mode. */ +static inline int onfi_get_sync_timing_mode(struct nand_chip *chip) +{ + if (!chip->onfi_version) + return ONFI_TIMING_MODE_UNKNOWN; + return le16_to_cpu(chip->onfi_params.src_sync_timing_mode); +} +#else +static inline int onfi_feature(struct nand_chip *chip) +{ + return 0; +} + +static inline int onfi_get_async_timing_mode(struct nand_chip *chip) +{ + return ONFI_TIMING_MODE_UNKNOWN; +} + +static inline int onfi_get_sync_timing_mode(struct nand_chip *chip) +{ + return ONFI_TIMING_MODE_UNKNOWN; +} +#endif + +int onfi_init_data_interface(struct nand_chip *chip, + struct nand_data_interface *iface, + enum nand_data_interface_type type, + int timing_mode); + +/* + * Check if it is a SLC nand. + * The !nand_is_slc() can be used to check the MLC/TLC nand chips. + * We do not distinguish the MLC and TLC now. + */ +static inline bool nand_is_slc(struct nand_chip *chip) +{ + return chip->bits_per_cell == 1; +} + +/** + * Check if the opcode's address should be sent only on the lower 8 bits + * @command: opcode to check + */ +static inline int nand_opcode_8bits(unsigned int command) +{ + switch (command) { + case NAND_CMD_READID: + case NAND_CMD_PARAM: + case NAND_CMD_GET_FEATURES: + case NAND_CMD_SET_FEATURES: + return 1; + default: + break; + } + return 0; +} + +/* return the supported JEDEC features. */ +static inline int jedec_feature(struct nand_chip *chip) +{ + return chip->jedec_version ? le16_to_cpu(chip->jedec_params.features) + : 0; +} + +/* Standard NAND functions from nand_base.c */ +void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len); +void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len); +void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len); +void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len); +uint8_t nand_read_byte(struct mtd_info *mtd); + +/* get timing characteristics from ONFI timing mode. */ +const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode); +/* get data interface from ONFI timing mode 0, used after reset. */ +const struct nand_data_interface *nand_get_default_data_interface(void); + +int nand_check_erased_ecc_chunk(void *data, int datalen, + void *ecc, int ecclen, + void *extraoob, int extraooblen, + int threshold); + +int nand_check_ecc_caps(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail); + +int nand_match_ecc_req(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail); + +int nand_maximize_ecc(struct nand_chip *chip, + const struct nand_ecc_caps *caps, int oobavail); + +/* Reset and initialize a NAND device */ +int nand_reset(struct nand_chip *chip, int chipnr); + +/* NAND operation helpers */ +int nand_reset_op(struct nand_chip *chip); +int nand_readid_op(struct nand_chip *chip, u8 addr, void *buf, + unsigned int len); +int nand_status_op(struct nand_chip *chip, u8 *status); +int nand_exit_status_op(struct nand_chip *chip); +int nand_erase_op(struct nand_chip *chip, unsigned int eraseblock); +int nand_read_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, void *buf, unsigned int len); +int nand_change_read_column_op(struct nand_chip *chip, + unsigned int offset_in_page, void *buf, + unsigned int len, bool force_8bit); +int nand_read_oob_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, void *buf, unsigned int len); +int nand_prog_page_begin_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, const void *buf, + unsigned int len); +int nand_prog_page_end_op(struct nand_chip *chip); +int nand_prog_page_op(struct nand_chip *chip, unsigned int page, + unsigned int offset_in_page, const void *buf, + unsigned int len); +int nand_change_write_column_op(struct nand_chip *chip, + unsigned int offset_in_page, const void *buf, + unsigned int len, bool force_8bit); +int nand_read_data_op(struct nand_chip *chip, void *buf, unsigned int len, + bool force_8bit); +int nand_write_data_op(struct nand_chip *chip, const void *buf, + unsigned int len, bool force_8bit); + +#endif /* __LINUX_MTD_RAWNAND_H */ diff --git a/roms/u-boot/include/linux/mtd/samsung_onenand.h b/roms/u-boot/include/linux/mtd/samsung_onenand.h new file mode 100644 index 000000000..7774fecdf --- /dev/null +++ b/roms/u-boot/include/linux/mtd/samsung_onenand.h @@ -0,0 +1,116 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2005-2009 Samsung Electronics + * Minkyu Kang <mk7.kang@samsung.com> + * Kyungmin Park <kyungmin.park@samsung.com> + */ + +#ifndef __SAMSUNG_ONENAND_H__ +#define __SAMSUNG_ONENAND_H__ + +/* + * OneNAND Controller + */ + +#ifndef __ASSEMBLY__ +struct samsung_onenand { + unsigned int mem_cfg; /* 0x0000 */ + unsigned char res1[0xc]; + unsigned int burst_len; /* 0x0010 */ + unsigned char res2[0xc]; + unsigned int mem_reset; /* 0x0020 */ + unsigned char res3[0xc]; + unsigned int int_err_stat; /* 0x0030 */ + unsigned char res4[0xc]; + unsigned int int_err_mask; /* 0x0040 */ + unsigned char res5[0xc]; + unsigned int int_err_ack; /* 0x0050 */ + unsigned char res6[0xc]; + unsigned int ecc_err_stat; /* 0x0060 */ + unsigned char res7[0xc]; + unsigned int manufact_id; /* 0x0070 */ + unsigned char res8[0xc]; + unsigned int device_id; /* 0x0080 */ + unsigned char res9[0xc]; + unsigned int data_buf_size; /* 0x0090 */ + unsigned char res10[0xc]; + unsigned int boot_buf_size; /* 0x00A0 */ + unsigned char res11[0xc]; + unsigned int buf_amount; /* 0x00B0 */ + unsigned char res12[0xc]; + unsigned int tech; /* 0x00C0 */ + unsigned char res13[0xc]; + unsigned int fba; /* 0x00D0 */ + unsigned char res14[0xc]; + unsigned int fpa; /* 0x00E0 */ + unsigned char res15[0xc]; + unsigned int fsa; /* 0x00F0 */ + unsigned char res16[0x3c]; + unsigned int sync_mode; /* 0x0130 */ + unsigned char res17[0xc]; + unsigned int trans_spare; /* 0x0140 */ + unsigned char res18[0x3c]; + unsigned int err_page_addr; /* 0x0180 */ + unsigned char res19[0x1c]; + unsigned int int_pin_en; /* 0x01A0 */ + unsigned char res20[0x1c]; + unsigned int acc_clock; /* 0x01C0 */ + unsigned char res21[0x1c]; + unsigned int err_blk_addr; /* 0x01E0 */ + unsigned char res22[0xc]; + unsigned int flash_ver_id; /* 0x01F0 */ + unsigned char res23[0x6c]; + unsigned int watchdog_cnt_low; /* 0x0260 */ + unsigned char res24[0xc]; + unsigned int watchdog_cnt_hi; /* 0x0270 */ + unsigned char res25[0xc]; + unsigned int sync_write; /* 0x0280 */ + unsigned char res26[0x1c]; + unsigned int cold_reset; /* 0x02A0 */ + unsigned char res27[0xc]; + unsigned int ddp_device; /* 0x02B0 */ + unsigned char res28[0xc]; + unsigned int multi_plane; /* 0x02C0 */ + unsigned char res29[0x1c]; + unsigned int trans_mode; /* 0x02E0 */ + unsigned char res30[0x1c]; + unsigned int ecc_err_stat2; /* 0x0300 */ + unsigned char res31[0xc]; + unsigned int ecc_err_stat3; /* 0x0310 */ + unsigned char res32[0xc]; + unsigned int ecc_err_stat4; /* 0x0320 */ + unsigned char res33[0x1c]; + unsigned int dev_page_size; /* 0x0340 */ + unsigned char res34[0x4c]; + unsigned int int_mon_status; /* 0x0390 */ +}; +#endif + +#define ONENAND_MEM_RESET_HOT 0x3 +#define ONENAND_MEM_RESET_COLD 0x2 +#define ONENAND_MEM_RESET_WARM 0x1 + +#define INT_ERR_ALL 0x3fff +#define CACHE_OP_ERR (1 << 13) +#define RST_CMP (1 << 12) +#define RDY_ACT (1 << 11) +#define INT_ACT (1 << 10) +#define UNSUP_CMD (1 << 9) +#define LOCKED_BLK (1 << 8) +#define BLK_RW_CMP (1 << 7) +#define ERS_CMP (1 << 6) +#define PGM_CMP (1 << 5) +#define LOAD_CMP (1 << 4) +#define ERS_FAIL (1 << 3) +#define PGM_FAIL (1 << 2) +#define INT_TO (1 << 1) +#define LD_FAIL_ECC_ERR (1 << 0) + +#define TSRF (1 << 0) + +/* common initialize function */ +extern void s3c_onenand_init(struct mtd_info *); +extern int s5pc110_chip_probe(struct mtd_info *); +extern int s5pc210_chip_probe(struct mtd_info *); + +#endif diff --git a/roms/u-boot/include/linux/mtd/spi-nor.h b/roms/u-boot/include/linux/mtd/spi-nor.h new file mode 100644 index 000000000..c3e38e499 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/spi-nor.h @@ -0,0 +1,444 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * Synced from Linux v4.19 + */ + +#ifndef __LINUX_MTD_SPI_NOR_H +#define __LINUX_MTD_SPI_NOR_H + +#include <linux/bitops.h> +#include <linux/mtd/cfi.h> +#include <linux/mtd/mtd.h> + +/* + * Manufacturer IDs + * + * The first byte returned from the flash after sending opcode SPINOR_OP_RDID. + * Sometimes these are the same as CFI IDs, but sometimes they aren't. + */ +#define SNOR_MFR_ATMEL CFI_MFR_ATMEL +#define SNOR_MFR_GIGADEVICE 0xc8 +#define SNOR_MFR_INTEL CFI_MFR_INTEL +#define SNOR_MFR_ST CFI_MFR_ST /* ST Micro <--> Micron */ +#define SNOR_MFR_MICRON CFI_MFR_MICRON /* ST Micro <--> Micron */ +#define SNOR_MFR_ISSI CFI_MFR_PMC +#define SNOR_MFR_MACRONIX CFI_MFR_MACRONIX +#define SNOR_MFR_SPANSION CFI_MFR_AMD +#define SNOR_MFR_SST CFI_MFR_SST +#define SNOR_MFR_WINBOND 0xef /* Also used by some Spansion */ + +/* + * Note on opcode nomenclature: some opcodes have a format like + * SPINOR_OP_FUNCTION{4,}_x_y_z. The numbers x, y, and z stand for the number + * of I/O lines used for the opcode, address, and data (respectively). The + * FUNCTION has an optional suffix of '4', to represent an opcode which + * requires a 4-byte (32-bit) address. + */ + +/* Flash opcodes. */ +#define SPINOR_OP_WREN 0x06 /* Write enable */ +#define SPINOR_OP_RDSR 0x05 /* Read status register */ +#define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */ +#define SPINOR_OP_RDSR2 0x3f /* Read status register 2 */ +#define SPINOR_OP_WRSR2 0x3e /* Write status register 2 */ +#define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */ +#define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */ +#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual Output SPI) */ +#define SPINOR_OP_READ_1_2_2 0xbb /* Read data bytes (Dual I/O SPI) */ +#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad Output SPI) */ +#define SPINOR_OP_READ_1_4_4 0xeb /* Read data bytes (Quad I/O SPI) */ +#define SPINOR_OP_READ_1_1_8 0x8b /* Read data bytes (Octal Output SPI) */ +#define SPINOR_OP_READ_1_8_8 0xcb /* Read data bytes (Octal I/O SPI) */ +#define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */ +#define SPINOR_OP_PP_1_1_4 0x32 /* Quad page program */ +#define SPINOR_OP_PP_1_4_4 0x38 /* Quad page program */ +#define SPINOR_OP_PP_1_1_8 0x82 /* Octal page program */ +#define SPINOR_OP_PP_1_8_8 0xc2 /* Octal page program */ +#define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */ +#define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */ +#define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */ +#define SPINOR_OP_CHIP_ERASE 0xc7 /* Erase whole flash chip */ +#define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */ +#define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */ +#define SPINOR_OP_RDSFDP 0x5a /* Read SFDP */ +#define SPINOR_OP_RDCR 0x35 /* Read configuration register */ +#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */ +#define SPINOR_OP_CLFSR 0x50 /* Clear flag status register */ +#define SPINOR_OP_RDEAR 0xc8 /* Read Extended Address Register */ +#define SPINOR_OP_WREAR 0xc5 /* Write Extended Address Register */ + +/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */ +#define SPINOR_OP_READ_4B 0x13 /* Read data bytes (low frequency) */ +#define SPINOR_OP_READ_FAST_4B 0x0c /* Read data bytes (high frequency) */ +#define SPINOR_OP_READ_1_1_2_4B 0x3c /* Read data bytes (Dual Output SPI) */ +#define SPINOR_OP_READ_1_2_2_4B 0xbc /* Read data bytes (Dual I/O SPI) */ +#define SPINOR_OP_READ_1_1_4_4B 0x6c /* Read data bytes (Quad Output SPI) */ +#define SPINOR_OP_READ_1_4_4_4B 0xec /* Read data bytes (Quad I/O SPI) */ +#define SPINOR_OP_READ_1_1_8_4B 0x7c /* Read data bytes (Octal Output SPI) */ +#define SPINOR_OP_READ_1_8_8_4B 0xcc /* Read data bytes (Octal I/O SPI) */ +#define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */ +#define SPINOR_OP_PP_1_1_4_4B 0x34 /* Quad page program */ +#define SPINOR_OP_PP_1_4_4_4B 0x3e /* Quad page program */ +#define SPINOR_OP_PP_1_1_8_4B 0x84 /* Octal page program */ +#define SPINOR_OP_PP_1_8_8_4B 0x8e /* Octal page program */ +#define SPINOR_OP_BE_4K_4B 0x21 /* Erase 4KiB block */ +#define SPINOR_OP_BE_32K_4B 0x5c /* Erase 32KiB block */ +#define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */ + +/* Double Transfer Rate opcodes - defined in JEDEC JESD216B. */ +#define SPINOR_OP_READ_1_1_1_DTR 0x0d +#define SPINOR_OP_READ_1_2_2_DTR 0xbd +#define SPINOR_OP_READ_1_4_4_DTR 0xed + +#define SPINOR_OP_READ_1_1_1_DTR_4B 0x0e +#define SPINOR_OP_READ_1_2_2_DTR_4B 0xbe +#define SPINOR_OP_READ_1_4_4_DTR_4B 0xee + +/* Used for SST flashes only. */ +#define SPINOR_OP_BP 0x02 /* Byte program */ +#define SPINOR_OP_WRDI 0x04 /* Write disable */ +#define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */ + +/* Used for SST26* flashes only. */ +#define SPINOR_OP_READ_BPR 0x72 /* Read block protection register */ +#define SPINOR_OP_WRITE_BPR 0x42 /* Write block protection register */ + +/* Used for S3AN flashes only */ +#define SPINOR_OP_XSE 0x50 /* Sector erase */ +#define SPINOR_OP_XPP 0x82 /* Page program */ +#define SPINOR_OP_XRDSR 0xd7 /* Read status register */ + +#define XSR_PAGESIZE BIT(0) /* Page size in Po2 or Linear */ +#define XSR_RDY BIT(7) /* Ready */ + +/* Used for Macronix and Winbond flashes. */ +#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ +#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ + +/* Used for Spansion flashes only. */ +#define SPINOR_OP_BRWR 0x17 /* Bank register write */ +#define SPINOR_OP_BRRD 0x16 /* Bank register read */ +#define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */ + +/* Used for Micron flashes only. */ +#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */ +#define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */ + +/* Status Register bits. */ +#define SR_WIP BIT(0) /* Write in progress */ +#define SR_WEL BIT(1) /* Write enable latch */ +/* meaning of other SR_* bits may differ between vendors */ +#define SR_BP0 BIT(2) /* Block protect 0 */ +#define SR_BP1 BIT(3) /* Block protect 1 */ +#define SR_BP2 BIT(4) /* Block protect 2 */ +#define SR_TB BIT(5) /* Top/Bottom protect */ +#define SR_SRWD BIT(7) /* SR write protect */ +/* Spansion/Cypress specific status bits */ +#define SR_E_ERR BIT(5) +#define SR_P_ERR BIT(6) + +#define SR_QUAD_EN_MX BIT(6) /* Macronix Quad I/O */ + +/* Enhanced Volatile Configuration Register bits */ +#define EVCR_QUAD_EN_MICRON BIT(7) /* Micron Quad I/O */ + +/* Flag Status Register bits */ +#define FSR_READY BIT(7) /* Device status, 0 = Busy, 1 = Ready */ +#define FSR_E_ERR BIT(5) /* Erase operation status */ +#define FSR_P_ERR BIT(4) /* Program operation status */ +#define FSR_PT_ERR BIT(1) /* Protection error bit */ + +/* Configuration Register bits. */ +#define CR_QUAD_EN_SPAN BIT(1) /* Spansion Quad I/O */ + +/* Status Register 2 bits. */ +#define SR2_QUAD_EN_BIT7 BIT(7) + +/* Supported SPI protocols */ +#define SNOR_PROTO_INST_MASK GENMASK(23, 16) +#define SNOR_PROTO_INST_SHIFT 16 +#define SNOR_PROTO_INST(_nbits) \ + ((((unsigned long)(_nbits)) << SNOR_PROTO_INST_SHIFT) & \ + SNOR_PROTO_INST_MASK) + +#define SNOR_PROTO_ADDR_MASK GENMASK(15, 8) +#define SNOR_PROTO_ADDR_SHIFT 8 +#define SNOR_PROTO_ADDR(_nbits) \ + ((((unsigned long)(_nbits)) << SNOR_PROTO_ADDR_SHIFT) & \ + SNOR_PROTO_ADDR_MASK) + +#define SNOR_PROTO_DATA_MASK GENMASK(7, 0) +#define SNOR_PROTO_DATA_SHIFT 0 +#define SNOR_PROTO_DATA(_nbits) \ + ((((unsigned long)(_nbits)) << SNOR_PROTO_DATA_SHIFT) & \ + SNOR_PROTO_DATA_MASK) + +#define SNOR_PROTO_IS_DTR BIT(24) /* Double Transfer Rate */ + +#define SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits) \ + (SNOR_PROTO_INST(_inst_nbits) | \ + SNOR_PROTO_ADDR(_addr_nbits) | \ + SNOR_PROTO_DATA(_data_nbits)) +#define SNOR_PROTO_DTR(_inst_nbits, _addr_nbits, _data_nbits) \ + (SNOR_PROTO_IS_DTR | \ + SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits)) + +enum spi_nor_protocol { + SNOR_PROTO_1_1_1 = SNOR_PROTO_STR(1, 1, 1), + SNOR_PROTO_1_1_2 = SNOR_PROTO_STR(1, 1, 2), + SNOR_PROTO_1_1_4 = SNOR_PROTO_STR(1, 1, 4), + SNOR_PROTO_1_1_8 = SNOR_PROTO_STR(1, 1, 8), + SNOR_PROTO_1_2_2 = SNOR_PROTO_STR(1, 2, 2), + SNOR_PROTO_1_4_4 = SNOR_PROTO_STR(1, 4, 4), + SNOR_PROTO_1_8_8 = SNOR_PROTO_STR(1, 8, 8), + SNOR_PROTO_2_2_2 = SNOR_PROTO_STR(2, 2, 2), + SNOR_PROTO_4_4_4 = SNOR_PROTO_STR(4, 4, 4), + SNOR_PROTO_8_8_8 = SNOR_PROTO_STR(8, 8, 8), + + SNOR_PROTO_1_1_1_DTR = SNOR_PROTO_DTR(1, 1, 1), + SNOR_PROTO_1_2_2_DTR = SNOR_PROTO_DTR(1, 2, 2), + SNOR_PROTO_1_4_4_DTR = SNOR_PROTO_DTR(1, 4, 4), + SNOR_PROTO_1_8_8_DTR = SNOR_PROTO_DTR(1, 8, 8), +}; + +static inline bool spi_nor_protocol_is_dtr(enum spi_nor_protocol proto) +{ + return !!(proto & SNOR_PROTO_IS_DTR); +} + +static inline u8 spi_nor_get_protocol_inst_nbits(enum spi_nor_protocol proto) +{ + return ((unsigned long)(proto & SNOR_PROTO_INST_MASK)) >> + SNOR_PROTO_INST_SHIFT; +} + +static inline u8 spi_nor_get_protocol_addr_nbits(enum spi_nor_protocol proto) +{ + return ((unsigned long)(proto & SNOR_PROTO_ADDR_MASK)) >> + SNOR_PROTO_ADDR_SHIFT; +} + +static inline u8 spi_nor_get_protocol_data_nbits(enum spi_nor_protocol proto) +{ + return ((unsigned long)(proto & SNOR_PROTO_DATA_MASK)) >> + SNOR_PROTO_DATA_SHIFT; +} + +static inline u8 spi_nor_get_protocol_width(enum spi_nor_protocol proto) +{ + return spi_nor_get_protocol_data_nbits(proto); +} + +#define SPI_NOR_MAX_CMD_SIZE 8 +enum spi_nor_ops { + SPI_NOR_OPS_READ = 0, + SPI_NOR_OPS_WRITE, + SPI_NOR_OPS_ERASE, + SPI_NOR_OPS_LOCK, + SPI_NOR_OPS_UNLOCK, +}; + +enum spi_nor_option_flags { + SNOR_F_USE_FSR = BIT(0), + SNOR_F_HAS_SR_TB = BIT(1), + SNOR_F_NO_OP_CHIP_ERASE = BIT(2), + SNOR_F_S3AN_ADDR_DEFAULT = BIT(3), + SNOR_F_READY_XSR_RDY = BIT(4), + SNOR_F_USE_CLSR = BIT(5), + SNOR_F_BROKEN_RESET = BIT(6), +}; + +/** + * struct flash_info - Forward declaration of a structure used internally by + * spi_nor_scan() + */ +struct flash_info; + +/* + * TODO: Remove, once all users of spi_flash interface are moved to MTD + * +struct spi_flash { + * Defined below (keep this text to enable searching for spi_flash decl) + * } + */ +#ifndef DT_PLAT_C +#define spi_flash spi_nor +#endif + +/** + * struct spi_nor - Structure for defining a the SPI NOR layer + * @mtd: point to a mtd_info structure + * @lock: the lock for the read/write/erase/lock/unlock operations + * @dev: point to a spi device, or a spi nor controller device. + * @info: spi-nor part JDEC MFR id and other info + * @manufacturer_sfdp: manufacturer specific SFDP table + * @page_size: the page size of the SPI NOR + * @addr_width: number of address bytes + * @erase_opcode: the opcode for erasing a sector + * @read_opcode: the read opcode + * @read_dummy: the dummy needed by the read operation + * @program_opcode: the program opcode + * @bank_read_cmd: Bank read cmd + * @bank_write_cmd: Bank write cmd + * @bank_curr: Current flash bank + * @sst_write_second: used by the SST write operation + * @flags: flag options for the current SPI-NOR (SNOR_F_*) + * @read_proto: the SPI protocol for read operations + * @write_proto: the SPI protocol for write operations + * @reg_proto the SPI protocol for read_reg/write_reg/erase operations + * @cmd_buf: used by the write_reg + * @prepare: [OPTIONAL] do some preparations for the + * read/write/erase/lock/unlock operations + * @unprepare: [OPTIONAL] do some post work after the + * read/write/erase/lock/unlock operations + * @read_reg: [DRIVER-SPECIFIC] read out the register + * @write_reg: [DRIVER-SPECIFIC] write data to the register + * @read: [DRIVER-SPECIFIC] read data from the SPI NOR + * @write: [DRIVER-SPECIFIC] write data to the SPI NOR + * @erase: [DRIVER-SPECIFIC] erase a sector of the SPI NOR + * at the offset @offs; if not provided by the driver, + * spi-nor will send the erase opcode via write_reg() + * @flash_lock: [FLASH-SPECIFIC] lock a region of the SPI NOR + * @flash_unlock: [FLASH-SPECIFIC] unlock a region of the SPI NOR + * @flash_is_locked: [FLASH-SPECIFIC] check if a region of the SPI NOR is + * completely locked + * @quad_enable: [FLASH-SPECIFIC] enables SPI NOR quad mode + * @priv: the private data + */ +struct spi_nor { + struct mtd_info mtd; + struct udevice *dev; + struct spi_slave *spi; + const struct flash_info *info; + u8 *manufacturer_sfdp; + u32 page_size; + u8 addr_width; + u8 erase_opcode; + u8 read_opcode; + u8 read_dummy; + u8 program_opcode; +#ifdef CONFIG_SPI_FLASH_BAR + u8 bank_read_cmd; + u8 bank_write_cmd; + u8 bank_curr; +#endif + enum spi_nor_protocol read_proto; + enum spi_nor_protocol write_proto; + enum spi_nor_protocol reg_proto; + bool sst_write_second; + u32 flags; + u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE]; + + int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops); + void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops); + int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len); + int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len); + + ssize_t (*read)(struct spi_nor *nor, loff_t from, + size_t len, u_char *read_buf); + ssize_t (*write)(struct spi_nor *nor, loff_t to, + size_t len, const u_char *write_buf); + int (*erase)(struct spi_nor *nor, loff_t offs); + + int (*flash_lock)(struct spi_nor *nor, loff_t ofs, uint64_t len); + int (*flash_unlock)(struct spi_nor *nor, loff_t ofs, uint64_t len); + int (*flash_is_locked)(struct spi_nor *nor, loff_t ofs, uint64_t len); + int (*quad_enable)(struct spi_nor *nor); + + void *priv; +/* Compatibility for spi_flash, remove once sf layer is merged with mtd */ + const char *name; + u32 size; + u32 sector_size; + u32 erase_size; +}; + +#ifndef __UBOOT__ +static inline void spi_nor_set_flash_node(struct spi_nor *nor, + const struct device_node *np) +{ + mtd_set_of_node(&nor->mtd, np); +} + +static inline const struct +device_node *spi_nor_get_flash_node(struct spi_nor *nor) +{ + return mtd_get_of_node(&nor->mtd); +} +#endif /* __UBOOT__ */ + +/** + * struct spi_nor_hwcaps - Structure for describing the hardware capabilies + * supported by the SPI controller (bus master). + * @mask: the bitmask listing all the supported hw capabilies + */ +struct spi_nor_hwcaps { + u32 mask; +}; + +/* + *(Fast) Read capabilities. + * MUST be ordered by priority: the higher bit position, the higher priority. + * As a matter of performances, it is relevant to use Octo SPI protocols first, + * then Quad SPI protocols before Dual SPI protocols, Fast Read and lastly + * (Slow) Read. + */ +#define SNOR_HWCAPS_READ_MASK GENMASK(14, 0) +#define SNOR_HWCAPS_READ BIT(0) +#define SNOR_HWCAPS_READ_FAST BIT(1) +#define SNOR_HWCAPS_READ_1_1_1_DTR BIT(2) + +#define SNOR_HWCAPS_READ_DUAL GENMASK(6, 3) +#define SNOR_HWCAPS_READ_1_1_2 BIT(3) +#define SNOR_HWCAPS_READ_1_2_2 BIT(4) +#define SNOR_HWCAPS_READ_2_2_2 BIT(5) +#define SNOR_HWCAPS_READ_1_2_2_DTR BIT(6) + +#define SNOR_HWCAPS_READ_QUAD GENMASK(10, 7) +#define SNOR_HWCAPS_READ_1_1_4 BIT(7) +#define SNOR_HWCAPS_READ_1_4_4 BIT(8) +#define SNOR_HWCAPS_READ_4_4_4 BIT(9) +#define SNOR_HWCAPS_READ_1_4_4_DTR BIT(10) + +#define SNOR_HWCPAS_READ_OCTO GENMASK(14, 11) +#define SNOR_HWCAPS_READ_1_1_8 BIT(11) +#define SNOR_HWCAPS_READ_1_8_8 BIT(12) +#define SNOR_HWCAPS_READ_8_8_8 BIT(13) +#define SNOR_HWCAPS_READ_1_8_8_DTR BIT(14) + +/* + * Page Program capabilities. + * MUST be ordered by priority: the higher bit position, the higher priority. + * Like (Fast) Read capabilities, Octo/Quad SPI protocols are preferred to the + * legacy SPI 1-1-1 protocol. + * Note that Dual Page Programs are not supported because there is no existing + * JEDEC/SFDP standard to define them. Also at this moment no SPI flash memory + * implements such commands. + */ +#define SNOR_HWCAPS_PP_MASK GENMASK(22, 16) +#define SNOR_HWCAPS_PP BIT(16) + +#define SNOR_HWCAPS_PP_QUAD GENMASK(19, 17) +#define SNOR_HWCAPS_PP_1_1_4 BIT(17) +#define SNOR_HWCAPS_PP_1_4_4 BIT(18) +#define SNOR_HWCAPS_PP_4_4_4 BIT(19) + +#define SNOR_HWCAPS_PP_OCTO GENMASK(22, 20) +#define SNOR_HWCAPS_PP_1_1_8 BIT(20) +#define SNOR_HWCAPS_PP_1_8_8 BIT(21) +#define SNOR_HWCAPS_PP_8_8_8 BIT(22) + +/** + * spi_nor_scan() - scan the SPI NOR + * @nor: the spi_nor structure + * + * The drivers can use this function to scan the SPI NOR. + * In the scanning, it will try to get all the necessary information to + * fill the mtd_info{} and the spi_nor{}. + * + * Return: 0 for success, others for failure. + */ +int spi_nor_scan(struct spi_nor *nor); + +#endif diff --git a/roms/u-boot/include/linux/mtd/spinand.h b/roms/u-boot/include/linux/mtd/spinand.h new file mode 100644 index 000000000..15bcd59f3 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/spinand.h @@ -0,0 +1,450 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (c) 2016-2017 Micron Technology, Inc. + * + * Authors: + * Peter Pan <peterpandong@micron.com> + */ +#ifndef __LINUX_MTD_SPINAND_H +#define __LINUX_MTD_SPINAND_H + +#ifndef __UBOOT__ +#include <linux/mutex.h> +#include <linux/bitops.h> +#include <linux/device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/nand.h> +#include <linux/spi/spi.h> +#include <linux/spi/spi-mem.h> +#else +#include <common.h> +#include <spi.h> +#include <spi-mem.h> +#include <linux/mtd/nand.h> +#endif + +/** + * Standard SPI NAND flash operations + */ + +#define SPINAND_RESET_OP \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xff, 1), \ + SPI_MEM_OP_NO_ADDR, \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_WR_EN_DIS_OP(enable) \ + SPI_MEM_OP(SPI_MEM_OP_CMD((enable) ? 0x06 : 0x04, 1), \ + SPI_MEM_OP_NO_ADDR, \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_READID_OP(ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x9f, 1), \ + SPI_MEM_OP_NO_ADDR, \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 1)) + +#define SPINAND_SET_FEATURE_OP(reg, valptr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x1f, 1), \ + SPI_MEM_OP_ADDR(1, reg, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_OUT(1, valptr, 1)) + +#define SPINAND_GET_FEATURE_OP(reg, valptr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x0f, 1), \ + SPI_MEM_OP_ADDR(1, reg, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_IN(1, valptr, 1)) + +#define SPINAND_BLK_ERASE_OP(addr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xd8, 1), \ + SPI_MEM_OP_ADDR(3, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_PAGE_READ_OP(addr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x13, 1), \ + SPI_MEM_OP_ADDR(3, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_PAGE_READ_FROM_CACHE_OP(fast, addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(fast ? 0x0b : 0x03, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 1)) + +#define SPINAND_PAGE_READ_FROM_CACHE_X2_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x3b, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 2)) + +#define SPINAND_PAGE_READ_FROM_CACHE_X4_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x6b, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_DUMMY(ndummy, 1), \ + SPI_MEM_OP_DATA_IN(len, buf, 4)) + +#define SPINAND_PAGE_READ_FROM_CACHE_DUALIO_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xbb, 1), \ + SPI_MEM_OP_ADDR(2, addr, 2), \ + SPI_MEM_OP_DUMMY(ndummy, 2), \ + SPI_MEM_OP_DATA_IN(len, buf, 2)) + +#define SPINAND_PAGE_READ_FROM_CACHE_QUADIO_OP(addr, ndummy, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0xeb, 1), \ + SPI_MEM_OP_ADDR(2, addr, 4), \ + SPI_MEM_OP_DUMMY(ndummy, 4), \ + SPI_MEM_OP_DATA_IN(len, buf, 4)) + +#define SPINAND_PROG_EXEC_OP(addr) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(0x10, 1), \ + SPI_MEM_OP_ADDR(3, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_NO_DATA) + +#define SPINAND_PROG_LOAD(reset, addr, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(reset ? 0x02 : 0x84, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_OUT(len, buf, 1)) + +#define SPINAND_PROG_LOAD_X4(reset, addr, buf, len) \ + SPI_MEM_OP(SPI_MEM_OP_CMD(reset ? 0x32 : 0x34, 1), \ + SPI_MEM_OP_ADDR(2, addr, 1), \ + SPI_MEM_OP_NO_DUMMY, \ + SPI_MEM_OP_DATA_OUT(len, buf, 4)) + +/** + * Standard SPI NAND flash commands + */ +#define SPINAND_CMD_PROG_LOAD_X4 0x32 +#define SPINAND_CMD_PROG_LOAD_RDM_DATA_X4 0x34 + +/* feature register */ +#define REG_BLOCK_LOCK 0xa0 +#define BL_ALL_UNLOCKED 0x00 + +/* configuration register */ +#define REG_CFG 0xb0 +#define CFG_OTP_ENABLE BIT(6) +#define CFG_ECC_ENABLE BIT(4) +#define CFG_QUAD_ENABLE BIT(0) + +/* status register */ +#define REG_STATUS 0xc0 +#define STATUS_BUSY BIT(0) +#define STATUS_ERASE_FAILED BIT(2) +#define STATUS_PROG_FAILED BIT(3) +#define STATUS_ECC_MASK GENMASK(5, 4) +#define STATUS_ECC_NO_BITFLIPS (0 << 4) +#define STATUS_ECC_HAS_BITFLIPS (1 << 4) +#define STATUS_ECC_UNCOR_ERROR (2 << 4) + +struct spinand_op; +struct spinand_device; + +#define SPINAND_MAX_ID_LEN 4 + +/** + * struct spinand_id - SPI NAND id structure + * @data: buffer containing the id bytes. Currently 4 bytes large, but can + * be extended if required + * @len: ID length + * + * struct_spinand_id->data contains all bytes returned after a READ_ID command, + * including dummy bytes if the chip does not emit ID bytes right after the + * READ_ID command. The responsibility to extract real ID bytes is left to + * struct_manufacurer_ops->detect(). + */ +struct spinand_id { + u8 data[SPINAND_MAX_ID_LEN]; + int len; +}; + +/** + * struct manufacurer_ops - SPI NAND manufacturer specific operations + * @detect: detect a SPI NAND device. Every time a SPI NAND device is probed + * the core calls the struct_manufacurer_ops->detect() hook of each + * registered manufacturer until one of them return 1. Note that + * the first thing to check in this hook is that the manufacturer ID + * in struct_spinand_device->id matches the manufacturer whose + * ->detect() hook has been called. Should return 1 if there's a + * match, 0 if the manufacturer ID does not match and a negative + * error code otherwise. When true is returned, the core assumes + * that properties of the NAND chip (spinand->base.memorg and + * spinand->base.eccreq) have been filled + * @init: initialize a SPI NAND device + * @cleanup: cleanup a SPI NAND device + * + * Each SPI NAND manufacturer driver should implement this interface so that + * NAND chips coming from this vendor can be detected and initialized properly. + */ +struct spinand_manufacturer_ops { + int (*detect)(struct spinand_device *spinand); + int (*init)(struct spinand_device *spinand); + void (*cleanup)(struct spinand_device *spinand); +}; + +/** + * struct spinand_manufacturer - SPI NAND manufacturer instance + * @id: manufacturer ID + * @name: manufacturer name + * @ops: manufacturer operations + */ +struct spinand_manufacturer { + u8 id; + char *name; + const struct spinand_manufacturer_ops *ops; +}; + +/* SPI NAND manufacturers */ +extern const struct spinand_manufacturer gigadevice_spinand_manufacturer; +extern const struct spinand_manufacturer macronix_spinand_manufacturer; +extern const struct spinand_manufacturer micron_spinand_manufacturer; +extern const struct spinand_manufacturer toshiba_spinand_manufacturer; +extern const struct spinand_manufacturer winbond_spinand_manufacturer; + +/** + * struct spinand_op_variants - SPI NAND operation variants + * @ops: the list of variants for a given operation + * @nops: the number of variants + * + * Some operations like read-from-cache/write-to-cache have several variants + * depending on the number of IO lines you use to transfer data or address + * cycles. This structure is a way to describe the different variants supported + * by a chip and let the core pick the best one based on the SPI mem controller + * capabilities. + */ +struct spinand_op_variants { + const struct spi_mem_op *ops; + unsigned int nops; +}; + +#define SPINAND_OP_VARIANTS(name, ...) \ + const struct spinand_op_variants name = { \ + .ops = (struct spi_mem_op[]) { __VA_ARGS__ }, \ + .nops = sizeof((struct spi_mem_op[]){ __VA_ARGS__ }) / \ + sizeof(struct spi_mem_op), \ + } + +/** + * spinand_ecc_info - description of the on-die ECC implemented by a SPI NAND + * chip + * @get_status: get the ECC status. Should return a positive number encoding + * the number of corrected bitflips if correction was possible or + * -EBADMSG if there are uncorrectable errors. I can also return + * other negative error codes if the error is not caused by + * uncorrectable bitflips + * @ooblayout: the OOB layout used by the on-die ECC implementation + */ +struct spinand_ecc_info { + int (*get_status)(struct spinand_device *spinand, u8 status); + const struct mtd_ooblayout_ops *ooblayout; +}; + +#define SPINAND_HAS_QE_BIT BIT(0) +#define SPINAND_HAS_CR_FEAT_BIT BIT(1) + +/** + * struct spinand_info - Structure used to describe SPI NAND chips + * @model: model name + * @devid: device ID + * @flags: OR-ing of the SPINAND_XXX flags + * @memorg: memory organization + * @eccreq: ECC requirements + * @eccinfo: on-die ECC info + * @op_variants: operations variants + * @op_variants.read_cache: variants of the read-cache operation + * @op_variants.write_cache: variants of the write-cache operation + * @op_variants.update_cache: variants of the update-cache operation + * @select_target: function used to select a target/die. Required only for + * multi-die chips + * + * Each SPI NAND manufacturer driver should have a spinand_info table + * describing all the chips supported by the driver. + */ +struct spinand_info { + const char *model; + u8 devid; + u32 flags; + struct nand_memory_organization memorg; + struct nand_ecc_req eccreq; + struct spinand_ecc_info eccinfo; + struct { + const struct spinand_op_variants *read_cache; + const struct spinand_op_variants *write_cache; + const struct spinand_op_variants *update_cache; + } op_variants; + int (*select_target)(struct spinand_device *spinand, + unsigned int target); +}; + +#define SPINAND_INFO_OP_VARIANTS(__read, __write, __update) \ + { \ + .read_cache = __read, \ + .write_cache = __write, \ + .update_cache = __update, \ + } + +#define SPINAND_ECCINFO(__ooblayout, __get_status) \ + .eccinfo = { \ + .ooblayout = __ooblayout, \ + .get_status = __get_status, \ + } + +#define SPINAND_SELECT_TARGET(__func) \ + .select_target = __func, + +#define SPINAND_INFO(__model, __id, __memorg, __eccreq, __op_variants, \ + __flags, ...) \ + { \ + .model = __model, \ + .devid = __id, \ + .memorg = __memorg, \ + .eccreq = __eccreq, \ + .op_variants = __op_variants, \ + .flags = __flags, \ + __VA_ARGS__ \ + } + +/** + * struct spinand_device - SPI NAND device instance + * @base: NAND device instance + * @slave: pointer to the SPI slave object + * @lock: lock used to serialize accesses to the NAND + * @id: NAND ID as returned by READ_ID + * @flags: NAND flags + * @op_templates: various SPI mem op templates + * @op_templates.read_cache: read cache op template + * @op_templates.write_cache: write cache op template + * @op_templates.update_cache: update cache op template + * @select_target: select a specific target/die. Usually called before sending + * a command addressing a page or an eraseblock embedded in + * this die. Only required if your chip exposes several dies + * @cur_target: currently selected target/die + * @eccinfo: on-die ECC information + * @cfg_cache: config register cache. One entry per die + * @databuf: bounce buffer for data + * @oobbuf: bounce buffer for OOB data + * @scratchbuf: buffer used for everything but page accesses. This is needed + * because the spi-mem interface explicitly requests that buffers + * passed in spi_mem_op be DMA-able, so we can't based the bufs on + * the stack + * @manufacturer: SPI NAND manufacturer information + * @priv: manufacturer private data + */ +struct spinand_device { + struct nand_device base; +#ifndef __UBOOT__ + struct spi_mem *spimem; + struct mutex lock; +#else + struct spi_slave *slave; +#endif + struct spinand_id id; + u32 flags; + + struct { + const struct spi_mem_op *read_cache; + const struct spi_mem_op *write_cache; + const struct spi_mem_op *update_cache; + } op_templates; + + int (*select_target)(struct spinand_device *spinand, + unsigned int target); + unsigned int cur_target; + + struct spinand_ecc_info eccinfo; + + u8 *cfg_cache; + u8 *databuf; + u8 *oobbuf; + u8 *scratchbuf; + const struct spinand_manufacturer *manufacturer; + void *priv; +}; + +/** + * mtd_to_spinand() - Get the SPI NAND device attached to an MTD instance + * @mtd: MTD instance + * + * Return: the SPI NAND device attached to @mtd. + */ +static inline struct spinand_device *mtd_to_spinand(struct mtd_info *mtd) +{ + return container_of(mtd_to_nanddev(mtd), struct spinand_device, base); +} + +/** + * spinand_to_mtd() - Get the MTD device embedded in a SPI NAND device + * @spinand: SPI NAND device + * + * Return: the MTD device embedded in @spinand. + */ +static inline struct mtd_info *spinand_to_mtd(struct spinand_device *spinand) +{ + return nanddev_to_mtd(&spinand->base); +} + +/** + * nand_to_spinand() - Get the SPI NAND device embedding an NAND object + * @nand: NAND object + * + * Return: the SPI NAND device embedding @nand. + */ +static inline struct spinand_device *nand_to_spinand(struct nand_device *nand) +{ + return container_of(nand, struct spinand_device, base); +} + +/** + * spinand_to_nand() - Get the NAND device embedded in a SPI NAND object + * @spinand: SPI NAND device + * + * Return: the NAND device embedded in @spinand. + */ +static inline struct nand_device * +spinand_to_nand(struct spinand_device *spinand) +{ + return &spinand->base; +} + +#ifndef __UBOOT__ +/** + * spinand_set_of_node - Attach a DT node to a SPI NAND device + * @spinand: SPI NAND device + * @np: DT node + * + * Attach a DT node to a SPI NAND device. + */ +static inline void spinand_set_of_node(struct spinand_device *spinand, + const struct device_node *np) +{ + nanddev_set_of_node(&spinand->base, np); +} +#else +/** + * spinand_set_of_node - Attach a DT node to a SPI NAND device + * @spinand: SPI NAND device + * @node: ofnode + * + * Attach a DT node to a SPI NAND device. + */ +static inline void spinand_set_ofnode(struct spinand_device *spinand, + ofnode node) +{ + nanddev_set_ofnode(&spinand->base, node); +} +#endif /* __UBOOT__ */ + +int spinand_match_and_init(struct spinand_device *dev, + const struct spinand_info *table, + unsigned int table_size, u8 devid); + +int spinand_upd_cfg(struct spinand_device *spinand, u8 mask, u8 val); +int spinand_select_target(struct spinand_device *spinand, unsigned int target); + +#endif /* __LINUX_MTD_SPINAND_H */ diff --git a/roms/u-boot/include/linux/mtd/st_smi.h b/roms/u-boot/include/linux/mtd/st_smi.h new file mode 100644 index 000000000..605896978 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/st_smi.h @@ -0,0 +1,100 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2009 + * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. + */ + +#ifndef ST_SMI_H +#define ST_SMI_H + +/* 0xF800.0000 . 0xFBFF.FFFF 64MB SMI (Serial Flash Mem) */ +/* 0xFC00.0000 . 0xFC1F.FFFF 2MB SMI (Serial Flash Reg.) */ + +#define FLASH_START_ADDRESS CONFIG_SYS_FLASH_BASE +#define FLASH_BANK_SIZE CONFIG_SYS_FLASH_BANK_SIZE + +#define SMIBANK0_BASE (FLASH_START_ADDRESS) +#define SMIBANK1_BASE (SMIBANK0_BASE + FLASH_BANK_SIZE) +#define SMIBANK2_BASE (SMIBANK1_BASE + FLASH_BANK_SIZE) +#define SMIBANK3_BASE (SMIBANK2_BASE + FLASH_BANK_SIZE) + +#define BANK0 0 +#define BANK1 1 +#define BANK2 2 +#define BANK3 3 + +struct smi_regs { + u32 smi_cr1; + u32 smi_cr2; + u32 smi_sr; + u32 smi_tr; + u32 smi_rr; +}; + +/* CONTROL REG 1 */ +#define BANK_EN 0x0000000F /* enables all banks */ +#define DSEL_TIME 0x00000060 /* Deselect time */ +#define PRESCAL5 0x00000500 /* AHB_CK prescaling value */ +#define PRESCALA 0x00000A00 /* AHB_CK prescaling value */ +#define PRESCAL3 0x00000300 /* AHB_CK prescaling value */ +#define PRESCAL4 0x00000400 /* AHB_CK prescaling value */ +#define SW_MODE 0x10000000 /* enables SW Mode */ +#define WB_MODE 0x20000000 /* Write Burst Mode */ +#define FAST_MODE 0x00008000 /* Fast Mode */ +#define HOLD1 0x00010000 + +/* CONTROL REG 2 */ +#define RD_STATUS_REG 0x00000400 /* reads status reg */ +#define WE 0x00000800 /* Write Enable */ +#define BANK0_SEL 0x00000000 /* Select Banck0 */ +#define BANK1_SEL 0x00001000 /* Select Banck1 */ +#define BANK2_SEL 0x00002000 /* Select Banck2 */ +#define BANK3_SEL 0x00003000 /* Select Banck3 */ +#define BANKSEL_SHIFT 12 +#define SEND 0x00000080 /* Send data */ +#define TX_LEN_1 0x00000001 /* data length = 1 byte */ +#define TX_LEN_2 0x00000002 /* data length = 2 byte */ +#define TX_LEN_3 0x00000003 /* data length = 3 byte */ +#define TX_LEN_4 0x00000004 /* data length = 4 byte */ +#define RX_LEN_1 0x00000010 /* data length = 1 byte */ +#define RX_LEN_2 0x00000020 /* data length = 2 byte */ +#define RX_LEN_3 0x00000030 /* data length = 3 byte */ +#define RX_LEN_4 0x00000040 /* data length = 4 byte */ +#define TFIE 0x00000100 /* Tx Flag Interrupt Enable */ +#define WCIE 0x00000200 /* WCF Interrupt Enable */ + +/* STATUS_REG */ +#define INT_WCF_CLR 0xFFFFFDFF /* clear: WCF clear */ +#define INT_TFF_CLR 0xFFFFFEFF /* clear: TFF clear */ +#define WIP_BIT 0x00000001 /* WIP Bit of SPI SR */ +#define WEL_BIT 0x00000002 /* WEL Bit of SPI SR */ +#define RSR 0x00000005 /* Read Status regiser */ +#define TFF 0x00000100 /* Transfer Finished FLag */ +#define WCF 0x00000200 /* Transfer Finished FLag */ +#define ERF1 0x00000400 /* Error Flag 1 */ +#define ERF2 0x00000800 /* Error Flag 2 */ +#define WM0 0x00001000 /* WM Bank 0 */ +#define WM1 0x00002000 /* WM Bank 1 */ +#define WM2 0x00004000 /* WM Bank 2 */ +#define WM3 0x00008000 /* WM Bank 3 */ +#define WM_SHIFT 12 + +/* TR REG */ +#define READ_ID 0x0000009F /* Read Identification */ +#define BULK_ERASE 0x000000C7 /* BULK erase */ +#define SECTOR_ERASE 0x000000D8 /* SECTOR erase */ +#define WRITE_ENABLE 0x00000006 /* Wenable command to FLASH */ + +struct flash_dev { + u32 density; + ulong size; + ushort sector_count; +}; + +#define SFLASH_PAGE_SIZE 0x100 /* flash page size */ +#define XFER_FINISH_TOUT 15 /* xfer finish timeout(in ms) */ +#define WMODE_TOUT 15 /* write enable timeout(in ms) */ + +extern void smi_init(void); + +#endif diff --git a/roms/u-boot/include/linux/mtd/ubi.h b/roms/u-boot/include/linux/mtd/ubi.h new file mode 100644 index 000000000..badf6a0c6 --- /dev/null +++ b/roms/u-boot/include/linux/mtd/ubi.h @@ -0,0 +1,289 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (c) International Business Machines Corp., 2006 + * + * Author: Artem Bityutskiy (Битюцкий Артём) + */ + +#ifndef __LINUX_UBI_H__ +#define __LINUX_UBI_H__ + +#include <linux/types.h> +#ifndef __UBOOT__ +#include <linux/ioctl.h> +#include <linux/scatterlist.h> +#include <mtd/ubi-user.h> +#endif + +/* All voumes/LEBs */ +#define UBI_ALL -1 + +/* + * Maximum number of scatter gather list entries, + * we use only 64 to have a lower memory foot print. + */ +#define UBI_MAX_SG_COUNT 64 + +/* + * enum ubi_open_mode - UBI volume open mode constants. + * + * UBI_READONLY: read-only mode + * UBI_READWRITE: read-write mode + * UBI_EXCLUSIVE: exclusive mode + * UBI_METAONLY: modify only the volume meta-data, + * i.e. the data stored in the volume table, but not in any of volume LEBs. + */ +enum { + UBI_READONLY = 1, + UBI_READWRITE, + UBI_EXCLUSIVE, + UBI_METAONLY +}; + +/** + * struct ubi_volume_info - UBI volume description data structure. + * @vol_id: volume ID + * @ubi_num: UBI device number this volume belongs to + * @size: how many physical eraseblocks are reserved for this volume + * @used_bytes: how many bytes of data this volume contains + * @used_ebs: how many physical eraseblocks of this volume actually contain any + * data + * @vol_type: volume type (%UBI_DYNAMIC_VOLUME or %UBI_STATIC_VOLUME) + * @corrupted: non-zero if the volume is corrupted (static volumes only) + * @upd_marker: non-zero if the volume has update marker set + * @alignment: volume alignment + * @usable_leb_size: how many bytes are available in logical eraseblocks of + * this volume + * @name_len: volume name length + * @name: volume name + * @cdev: UBI volume character device major and minor numbers + * + * The @corrupted flag is only relevant to static volumes and is always zero + * for dynamic ones. This is because UBI does not care about dynamic volume + * data protection and only cares about protecting static volume data. + * + * The @upd_marker flag is set if the volume update operation was interrupted. + * Before touching the volume data during the update operation, UBI first sets + * the update marker flag for this volume. If the volume update operation was + * further interrupted, the update marker indicates this. If the update marker + * is set, the contents of the volume is certainly damaged and a new volume + * update operation has to be started. + * + * To put it differently, @corrupted and @upd_marker fields have different + * semantics: + * o the @corrupted flag means that this static volume is corrupted for some + * reasons, but not because an interrupted volume update + * o the @upd_marker field means that the volume is damaged because of an + * interrupted update operation. + * + * I.e., the @corrupted flag is never set if the @upd_marker flag is set. + * + * The @used_bytes and @used_ebs fields are only really needed for static + * volumes and contain the number of bytes stored in this static volume and how + * many eraseblock this data occupies. In case of dynamic volumes, the + * @used_bytes field is equivalent to @size*@usable_leb_size, and the @used_ebs + * field is equivalent to @size. + * + * In general, logical eraseblock size is a property of the UBI device, not + * of the UBI volume. Indeed, the logical eraseblock size depends on the + * physical eraseblock size and on how much bytes UBI headers consume. But + * because of the volume alignment (@alignment), the usable size of logical + * eraseblocks if a volume may be less. The following equation is true: + * @usable_leb_size = LEB size - (LEB size mod @alignment), + * where LEB size is the logical eraseblock size defined by the UBI device. + * + * The alignment is multiple to the minimal flash input/output unit size or %1 + * if all the available space is used. + * + * To put this differently, alignment may be considered is a way to change + * volume logical eraseblock sizes. + */ +struct ubi_volume_info { + int ubi_num; + int vol_id; + int size; + long long used_bytes; + int used_ebs; + int vol_type; + int corrupted; + int upd_marker; + int alignment; + int usable_leb_size; + int name_len; + const char *name; + dev_t cdev; +}; + +/** + * struct ubi_sgl - UBI scatter gather list data structure. + * @list_pos: current position in @sg[] + * @page_pos: current position in @sg[@list_pos] + * @sg: the scatter gather list itself + * + * ubi_sgl is a wrapper around a scatter list which keeps track of the + * current position in the list and the current list item such that + * it can be used across multiple ubi_leb_read_sg() calls. + */ +struct ubi_sgl { + int list_pos; + int page_pos; +#ifndef __UBOOT__ + struct scatterlist sg[UBI_MAX_SG_COUNT]; +#endif +}; + +/** + * ubi_sgl_init - initialize an UBI scatter gather list data structure. + * @usgl: the UBI scatter gather struct itself + * + * Please note that you still have to use sg_init_table() or any adequate + * function to initialize the unterlaying struct scatterlist. + */ +static inline void ubi_sgl_init(struct ubi_sgl *usgl) +{ + usgl->list_pos = 0; + usgl->page_pos = 0; +} + +/** + * struct ubi_device_info - UBI device description data structure. + * @ubi_num: ubi device number + * @leb_size: logical eraseblock size on this UBI device + * @leb_start: starting offset of logical eraseblocks within physical + * eraseblocks + * @min_io_size: minimal I/O unit size + * @max_write_size: maximum amount of bytes the underlying flash can write at a + * time (MTD write buffer size) + * @ro_mode: if this device is in read-only mode + * @cdev: UBI character device major and minor numbers + * + * Note, @leb_size is the logical eraseblock size offered by the UBI device. + * Volumes of this UBI device may have smaller logical eraseblock size if their + * alignment is not equivalent to %1. + * + * The @max_write_size field describes flash write maximum write unit. For + * example, NOR flash allows for changing individual bytes, so @min_io_size is + * %1. However, it does not mean than NOR flash has to write data byte-by-byte. + * Instead, CFI NOR flashes have a write-buffer of, e.g., 64 bytes, and when + * writing large chunks of data, they write 64-bytes at a time. Obviously, this + * improves write throughput. + * + * Also, the MTD device may have N interleaved (striped) flash chips + * underneath, in which case @min_io_size can be physical min. I/O size of + * single flash chip, while @max_write_size can be N * @min_io_size. + * + * The @max_write_size field is always greater or equivalent to @min_io_size. + * E.g., some NOR flashes may have (@min_io_size = 1, @max_write_size = 64). In + * contrast, NAND flashes usually have @min_io_size = @max_write_size = NAND + * page size. + */ +struct ubi_device_info { + int ubi_num; + int leb_size; + int leb_start; + int min_io_size; + int max_write_size; + int ro_mode; +#ifndef __UBOOT__ + dev_t cdev; +#endif +}; + +/* + * Volume notification types. + * @UBI_VOLUME_ADDED: a volume has been added (an UBI device was attached or a + * volume was created) + * @UBI_VOLUME_REMOVED: a volume has been removed (an UBI device was detached + * or a volume was removed) + * @UBI_VOLUME_RESIZED: a volume has been re-sized + * @UBI_VOLUME_RENAMED: a volume has been re-named + * @UBI_VOLUME_UPDATED: data has been written to a volume + * + * These constants define which type of event has happened when a volume + * notification function is invoked. + */ +enum { + UBI_VOLUME_ADDED, + UBI_VOLUME_REMOVED, + UBI_VOLUME_RESIZED, + UBI_VOLUME_RENAMED, + UBI_VOLUME_UPDATED, +}; + +/* + * struct ubi_notification - UBI notification description structure. + * @di: UBI device description object + * @vi: UBI volume description object + * + * UBI notifiers are called with a pointer to an object of this type. The + * object describes the notification. Namely, it provides a description of the + * UBI device and UBI volume the notification informs about. + */ +struct ubi_notification { + struct ubi_device_info di; + struct ubi_volume_info vi; +}; + +/* UBI descriptor given to users when they open UBI volumes */ +struct ubi_volume_desc; + +int ubi_get_device_info(int ubi_num, struct ubi_device_info *di); +void ubi_get_volume_info(struct ubi_volume_desc *desc, + struct ubi_volume_info *vi); +struct ubi_volume_desc *ubi_open_volume(int ubi_num, int vol_id, int mode); +struct ubi_volume_desc *ubi_open_volume_nm(int ubi_num, const char *name, + int mode); +struct ubi_volume_desc *ubi_open_volume_path(const char *pathname, int mode); + +#ifndef __UBOOT__ +typedef int (*notifier_fn_t)(void *nb, + unsigned long action, void *data); + +struct notifier_block { + notifier_fn_t notifier_call; + struct notifier_block *next; + void *next; + int priority; +}; + +int ubi_register_volume_notifier(struct notifier_block *nb, + int ignore_existing); +int ubi_unregister_volume_notifier(struct notifier_block *nb); +#endif + +void ubi_close_volume(struct ubi_volume_desc *desc); +int ubi_leb_read(struct ubi_volume_desc *desc, int lnum, char *buf, int offset, + int len, int check); +int ubi_leb_read_sg(struct ubi_volume_desc *desc, int lnum, struct ubi_sgl *sgl, + int offset, int len, int check); +int ubi_leb_write(struct ubi_volume_desc *desc, int lnum, const void *buf, + int offset, int len); +int ubi_leb_change(struct ubi_volume_desc *desc, int lnum, const void *buf, + int len); +int ubi_leb_erase(struct ubi_volume_desc *desc, int lnum); +int ubi_leb_unmap(struct ubi_volume_desc *desc, int lnum); +int ubi_leb_map(struct ubi_volume_desc *desc, int lnum); +int ubi_is_mapped(struct ubi_volume_desc *desc, int lnum); +int ubi_sync(int ubi_num); +int ubi_flush(int ubi_num, int vol_id, int lnum); + +/* + * This function is the same as the 'ubi_leb_read()' function, but it does not + * provide the checking capability. + */ +static inline int ubi_read(struct ubi_volume_desc *desc, int lnum, char *buf, + int offset, int len) +{ + return ubi_leb_read(desc, lnum, buf, offset, len, 0); +} + +/* + * This function is the same as the 'ubi_leb_read_sg()' function, but it does + * not provide the checking capability. + */ +static inline int ubi_read_sg(struct ubi_volume_desc *desc, int lnum, + struct ubi_sgl *sgl, int offset, int len) +{ + return ubi_leb_read_sg(desc, lnum, sgl, offset, len, 0); +} +#endif /* !__LINUX_UBI_H__ */ |